Changes for page DS20L -- LoRaWAN Smart Distance Detector User Manual 01

Last modified by Mengting Qiu on 2023/12/14 11:15

From 39.6 to 39.7 From 67.7 to 67.8

From version 39.7

edited by Xiaoling
on 2023/05/19 17:49

Change comment: There is no comment for this version

To version 67.7

edited by Xiaoling
on 2023/05/30 14:32

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 19 added, 0 removed)

Details

Page properties

Title

@@ -1,1 +1,1 @@
--S31-LB / S31B-LB LoRaWAN Outdoor Temperature & Humidity Sensor User Manual
++SW3L-LB -- LoRaWAN Flow Sensor User Manual

Content

@@ -1,9 +1,10 @@
  (% style="text-align:center" %)
--[[image:S31-B.jpg]]
++[[image:image-20230530140053-1.jpeg||height="645" width="645"]]
++
  **Table of Contents：**
  {{toc/}}
@@ -15,41 +15,43 @@
  = 1. Introduction =
--== 1.1 What is S31x-LB LoRaWAN Temperature & Humidity Sensor ==
++== 1.1 What is SW3L-LB LoRaWAN Flow Sensor ==
--The Dragino S31x-LB is a (% style="color:blue" %)**LoRaWAN Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)**surrounding environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via LoRaWAN wireless protocol.
++The Dragino SW3L-LB is a (% style="color:blue" %)**LoRaWAN Flow Sensor**(%%). It detects water flow volume and uplink to IoT server via LoRaWAN network. User can use this to(% style="color:blue" %)** monitor the water usage for buildings.**
--The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
++The SW3L-LB will send water flow volume every 20 minutes. It can also (% style="color:blue" %)**detect the water flow status**(%%) and (% style="color:blue" %)**send Alarm**(%%), to avoid the waste for water usage such as broken toilet case.
--The LoRa wireless technology used in S31x-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
++SW3L-LB is designed for both indoor and outdoor use. It has a weatherproof enclosure and industrial level battery to work in low to high temperatures.
--S31x-LB supports (% style="color:blue" %)**Temperature & Humdity alarm feature**(%%), user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
++The LoRa wireless technology used in SW3L-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
--S31x-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
++SW3L-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
--S31x-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
++SW3L-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
--Each S31x-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
++Each SW3L-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
++[[image:image-20230530135919-1.png||height="404" width="806"]]
++
++
  == 1.2 Features ==
  * LoRaWAN 1.0.3 Class A
--* Ultra-low power consumption
--* External 3 meters SHT31 probe (For S31-LB)
--* Measure range -55°C ~~ 125°C
--* Temperature & Humidity alarm
  * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
++* Ultra-low power consumption
++* Upload water flow volume
++* Monitor water waste
++* AT Commands to change parameters
++* supports Datalog feature
  * Support Bluetooth v5.1 and LoRaWAN remote configure
  * Support wireless OTA update firmware
--* Uplink on periodically
++* Uplink on periodically and open/close event
  * Downlink to change configure
  * 8500mAh Battery for long term use
--
--
  == 1.3 Specification ==
@@ -58,20 +58,6 @@
  * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
  * Operating Temperature: -40 ~~ 85°C
--(% style="color:#037691" %)**Temperature Sensor:**
--
--* Range: -40 to + 80°C
--* Accuracy: ±0.2 @ 0-90 °C
--* Resolution: 0.1°C
--* Long Term Shift: <0.03 °C/yr
--
--(% style="color:#037691" %)**Humidity Sensor: **
--
--* Range: 0 ~~ 99.9% RH
--* Accuracy: ± 2%RH ( 0 ~~ 100%RH)
--* Resolution: 0.01% RH
--* Long Term Shift: <0.25 %RH/yr
--
  (% style="color:#037691" %)**LoRa Spec:**
  * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
@@ -92,17 +92,23 @@
  * Sleep Mode: 5uA @ 3.3v
  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
++== 1.4 Applications ==
--== 1.4 Sleep mode and working mode ==
++* Flow Sensor application
++* Water Control
++* Toilet Flow Sensor
++* Monitor Waste water
++== 1.5 Sleep mode and working mode ==
++
  (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
  (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
--== 1.5 Button & LEDs ==
++== 1.6 Button & LEDs ==
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
@@ -121,14 +121,12 @@
  )))
  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
++== 1.7 BLE connection ==
--== 1.6 BLE connection ==
++SW3L-LB support BLE remote configure.
--S31x-LB support BLE remote configure.
--
--
  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
  * Press button to send an uplink
@@ -138,31 +138,26 @@
  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
--== 1.7  Hardware Variant ==
++== 1.8 Pin Definitions ==
++[[image:image-20230523174230-1.png]]
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 218px;background-color:#D9E2F3;color:#0070C0" %)Probe Info
--|(% style="width:102px" %)S31-LB|(% style="width:190px" %)[[image:S31.jpg]]|(% style="width:297px" %)(((
--1 x SHT31 Probe
--Cable Length : 2 meters
++== 1.9 Flow Sensor Spec ==
--
--)))
--|(% style="width:102px" %)S31B-LB|(% style="width:190px" %)[[image:S31B.jpg]]|(% style="width:297px" %)(((
--1 x SHT31 Probe
--Installed in device.
++(((
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Model**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Probe**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Diameter**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Range**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**Max Pressure**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**Measure**
++|(% style="width:88px" %)SW3L-004|(% style="width:75px" %)DW-004|(% style="width:107px" %)G1/2" /DN15|(% style="width:101px" %)1~~30L/min|(% style="width:116px" %)≤ 2.0Mpa|(% style="width:124px" %)450 pulse = 1 L
++|(% style="width:88px" %)SW3L-006|(% style="width:75px" %)DW-006|(% style="width:107px" %)G3/4" /DN20|(% style="width:101px" %)1~~60L/min|(% style="width:116px" %)≤ 1.2Mpa|(% style="width:124px" %)390 pulse = 1 L
++|(% style="width:88px" %)SW3L-010|(% style="width:75px" %)DW-010|(% style="width:107px" %)G 1" /DN25|(% style="width:101px" %)2~~100L/min|(% style="width:116px" %)≤ 2.0Mpa|(% style="width:124px" %)64 pulse = 1 L
  )))
--(% style="display:none" %)
++== 2.10 Mechanical ==
--== 1.8 Mechanical ==
--
--
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
@@ -172,13 +172,29 @@
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
--= 2. Configure S31x-LB to connect to LoRaWAN network =
++(% style="color:blue" %)**DW-004 Flow Sensor: diameter: G1/2” / DN15.  450 pulse = 1 L**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091350-1.png?width=722&height=385&rev=1.1||alt="image-20220519091350-1.png"]]
++
++
++(% style="color:blue" %)**006: DW-006 Flow Sensor: diameter: G3/4” / DN20.  390 pulse = 1 L**
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091423-2.png?width=723&height=258&rev=1.1||alt="image-20220519091423-2.png"]]
++
++
++(% style="color:blue" %)**010: DW-010 Flow Sensor: diameter: G 1” / DN25.   64 pulse = 1 L**
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091423-3.png?width=724&height=448&rev=1.1||alt="image-20220519091423-3.png"]]
++
++
++= 2. Configure CPL03-LB to connect to LoRaWAN network =
++
  == 2.1 How it works ==
--The S31x-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
++The SW3L-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the SW3L-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
++(% style="display:none" %) (%%)
  == 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
@@ -185,13 +185,15 @@
  Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]]  as a LoRaWAN gateway in this example.
--The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
++The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
++[[image:image-20230530135929-2.png||height="404" width="806"]](% style="display:none" %)
--(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB.
--Each S31x-LB is shipped with a sticker with the default device EUI as below:
++(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SW3L-LB.
++Each SW3L-LB is shipped with a sticker with the default device EUI as below:
++
  [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
@@ -219,10 +219,10 @@
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
--(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB
++(% style="color:blue" %)**Step 2:**(%%) Activate on SW3L-LB
--Press the button for 5 seconds to activate the S31x-LB.
++Press the button for 5 seconds to activate the SW3L-LB.
  (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
@@ -234,8 +234,10 @@
  === 2.3.1 Device Status, FPORT~=5 ===
--Users can use the downlink command(**0x26 01**) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.
++Include device configure status. Once SW3L-LB Joined the network, it will uplink this message to the server. After that, SW3L-LB will uplink Device Status every 12 hours.
++Users can use the downlink command(**0x26 01**) to ask SW3L-LB to send device configure detail, include device configure status. SW3L-LB will uplink a payload via FPort=5 to server.
++
  The Payload format is as below.
@@ -246,10 +246,10 @@
  Example parse in TTNv3
--[[image:image-20230421171614-1.png||alt="图片-20230421171614-1.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/1652925144491-755.png?width=732&height=139&rev=1.1||alt="1652925144491-755.png"]]
--(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
++(% style="color:#037691" %)**Sensor Model**(%%): For SW3L-LB, this value is 0x11
  (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
@@ -302,246 +302,360 @@
  Ex2: 0x0B49 = 2889mV
--=== 2.3.2  Sensor Data. FPORT~=2 ===
++=== 2.3.2 Sensor Configuration, FPORT~=4 ===
--Sensor Data is uplink via FPORT=2
++SW3L will only send this command after getting the downlink command (0x26 02) from the server.
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
--|=(% style="width: 90px;background-color:#D9E2F3" %)(((
--**Size(bytes)**
--)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2
--|(% style="width:99px" %)**Value**|(% style="width:69px" %)(((
--[[Battery>>||anchor="HBattery"]]
--)))|(% style="width:130px" %)(((
--[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
--)))|(% style="width:91px" %)(((
--[[Alarm Flag>>||anchor="HAlarmFlag26MOD"]]
--)))|(% style="width:103px" %)(((
--[[Temperature>>||anchor="HTemperature"]]
--)))|(% style="width:80px" %)(((
--[[Humidity>>||anchor="HHumidity"]]
--)))
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %) **Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:105px" %)**3**|(% style="background-color:#d9e2f3; color:#0070c0; width:60px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:96px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:105px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:74px" %)**1**
++|**Value**|(% style="width:104px" %)TDC(unit:sec)|(% style="width:43px" %)N/A|(% style="width:91px" %)Stop Timer|(% style="width:100px" %)Alarm Timer|(% style="width:69px" %)Reserve
--==== (% style="color:#4472c4" %)**Battery**(%%) ====
++* (% style="color:#037691" %)**TDC: (default: 0x0004B0)**
--Sensor Battery Level.
++Uplink interval for the total pulse count, default value is 0x0004B0 which is 1200 seconds = 20 minutes.
--Ex1: 0x0B45 = 2885mV
--Ex2: 0x0B49 = 2889mV
++* (% style="color:#037691" %)**STOP Duration & Alarm Timer**
++Shows the configure value of [[Alarm for continuously water flow>>||anchor="H3.4Alarmforcontinuouslywaterflow"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095747-2.png?width=723&height=113&rev=1.1||alt="image-20220519095747-2.png"]]
--==== (% style="color:#4472c4" %)**Temperature**(%%) ====
--**Example**:
++=== 2.3.3 Water Flow Value, Uplink FPORT~=2 ===
--If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
--If payload is: FF3FH :  (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
++(((
++SW3L will send this uplink **after** Device Status once join the LoRaWAN network successfully. And SW3L will:
++)))
--（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
++(((
++periodically send this uplink every 20 minutes, this interval [[can be changed>>||anchor="H3.1SetTransmitIntervalTime"]].
++)))
++(((
++Uplink Payload totals 11 bytes.
++)))
--==== (% style="color:#4472c4" %)**Humidity**(%%) ====
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|=(% colspan="6" style="width: 510px;background-color:#D9E2F3;color:#0070C0" %)**Water Flow Value,  FPORT=2**
++|(% style="width:60px" %)**Size(bytes)**|(% style="width:130px" %)**1**|(% style="width:130px" %)**4**|(% style="width:30px" %)**1**|(% style="width:50px" %)**1**|(% style="width:80px" %)**4**
++|(% style="width:110px" %)**Value**|(% style="width:81px" %)Calculate Flag  & [[Alarm>>||anchor="H3.4Alarmforcontinuouslywaterflow"]]|(% style="width:95px" %)(((
++Total pulse Or Last Pulse
++)))|(% style="width:55px" %)MOD|(% style="width:115px" %)Reserve(0x01)|(% style="width:129px" %)[[Unix TimeStamp>>||anchor="H2.4.1UnixTimeStamp"]]
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:470px" %)
++|=(% colspan="4" style="width: 470px;background-color:#D9E2F3;color:#0070C0" %)**Status & Alarm field**
++|(% style="width:60px" %)**Size(bit)**|(% style="width:80px" %)**6**|(% style="width:310px" %)**1**|(% style="width:20px" %)**1**
++|(% style="width:88px" %)**Value**|(% style="width:117px" %)Calculate Flag|(% style="width:221px" %)Alarm: 0: No Alarm; 1: Alarm|(% style="width:64px" %)N/A
--Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-3.png?width=736&height=284&rev=1.1||alt="image-20220519095946-3.png"]]
--==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
++* (((
++(% style="color:#037691" %)**Calculate Flag**
++)))
++(((
++The calculate flag is a user defined field, IoT server can use this flag to handle different meters with different pulse factors. For example, if there are 100 Flow Sensors, meters 1 ~~50 are 1 liter/pulse and meters 51 ~~ 100 has 1.5 liter/pulse.
++)))
--**Example:**
++(((
++**Example: in the default payload:**
++)))
--If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message
++* (((
++calculate flag=0: for SW3L-004 Flow Sensor: 450 pulse = 1 L
++)))
++* (((
++calculate flag=1: for SW3L-006 Flow Sensor: 390 pulse = 1 L
++)))
++* (((
++calculate flag=2: for SW3L-010 Flow Sensor: 64 pulse = 1 L
++)))
--If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm
++(((
++Default value: 0.
++)))
--If payload >> 2 = 0x00     **~-~->**  means MOD=1, This is a sampling uplink message
++(((
++Range (6 bits): (b)000000 ~~ (b) 111111
--If payload >> 2 = 0x31     **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail.
++If user use with a meter for example is 0.02L/pulse. To proper decode the correct value in server,
++1) User can set the Calculate Flag of this sensor to 3.
--== 2.4 Payload Decoder file ==
++2) In server side, when a sensor data arrive, the decoder will check the value of Calculate Flag, It the value is 3, the total volume = 0.02 x Pulse Count.
++)))
++(((
++(% style="color:red" %)**NOTE: User need to set Calculate Flag to proper value before use Flow Sensor. Downlink or AT Command see: **(%%)Refer: [[Set Calculate Flag>>||anchor="H3.6Setthecalculateflag"]]
++)))
--In TTN, use can add a custom payload so it shows friendly reading
++* (((
++(% style="color:#037691" %)**Alarm**
++)))
--In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
++(((
++See [[Alarm for continuously water flow>>||anchor="H3.4Alarmforcontinuouslywaterflow"]]
++)))
--[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-4.png?width=724&height=65&rev=1.1||alt="image-20220519095946-4.png"]]
--== 2.5 Datalog Feature ==
++* (((
++(% style="color:#037691" %)**Total pulse**
++)))
++(((
++Total pulse/counting since factory
++)))
--Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
++(((
++Range (4 Bytes) : 0x00000000~~ 0xFFFFFFFF .
++)))
++* (((
++(% style="color:#037691" %)**Last Pulse**
++)))
--=== 2.5.1 Ways to get datalog via LoRaWAN ===
++(((
++Total pulse since last FPORT=2 uplink. (Default 20 minutes)
++)))
++(((
++Range (4 Bytes) : 0x00000000~~ 0xFFFFFFFF .
++)))
--Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
++* (((
++(% style="color:#037691" %)**MOD: Default =0**
++)))
--* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
--* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
++(((
++MOD=0 ~-~-> Uplink Total Pulse since factory
++)))
--Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
++(((
++MOD=1 ~-~-> Uplink total pulse since last FPORT=2 uplink.
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
++* (((
++(% style="color:#037691" %)**Water Flow Value**
++)))
++(((
++**Total Water Flow Volume = (Calculate Flag) x (Total Pulse)=9597/450=21.3L**
++)))
--=== 2.5.2 Unix TimeStamp ===
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-5.png?width=727&height=50&rev=1.1||alt="image-20220519095946-5.png"]]
--S31x-LB uses Unix TimeStamp format based on
++(((
++**Total Water Flow for TDC timer = (Calculate Flag) x (Last Pulse)=79/450=0.2L**
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-6.png?width=733&height=43&rev=1.1||alt="image-20220519095946-6.png"]] **       **
--User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
--Below is the converter example
++=== 2.3.4 Historical Water Flow Status, FPORT~=3 ===
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
++(((
++SW3L stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.4DatalogFeature"]].
++)))
--So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
++(((
++The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time water flow status.
++)))
++* (((
++Each data entry is 11 bytes and has the same structure as [[real time water flow status>>||anchor="H2.3.3A0WaterFlowValue2CUplinkFPORT3D2"]], to save airtime and battery, SW3L will send max bytes according to the current DR and Frequency bands.
++)))
--=== 2.5.3 Set Device Time ===
++(((
++For example, in the US915 band, the max payload for different DR is:
++)))
++(((
++**a) DR0:** max is 11 bytes so one entry of data
++)))
--User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
++(((
++**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
++)))
--Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
++(((
++**c) DR2:** total payload includes 11 entries of data
++)))
--(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
++(((
++**d) DR3:** total payload includes 22 entries of data.
++)))
++(((
++If SW3L doesn't have any data in the polling time. It will uplink 11 bytes of 0
++)))
--=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
++(((
++(% style="color:#037691" %)**Downlink:**
++)))
++(((
++0x31 62 46 B1 F0 62 46 B3 94 07
++)))
--The Datalog uplinks will use below payload format.
++[[image:1652926690850-712.png||_mstalt="295178" height="115" width="726"]]
--**Retrieval data payload:**
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 80px;background-color:#D9E2F3" %)(((
--**Size(bytes)**
--)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**
--|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((
--Temp_Black
--)))|(% style="width:51px" %)Temp_White|(% style="width:89px" %)Temp_ Red or Temp _White|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]
++(((
++(% style="color:#037691" %)**Uplink:**
++)))
--**Poll message flag & Ext:**
++(((
++00 00 01 00 00 00 00 62 46 B2 26 00 00 01 00 00 00 00 62 46 B2 5D 00 00 01 00 00 00 00 62 46 B2 99 00 00 01 00 00 00 00 62 46 B2 D5 00 00 01 00 00 01 15 62 46 B3 11 00 00 01 00 00 01 1F 62 46 B3 7E
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]
++(((
++(% style="color:#037691" %)**Parsed Value:**
++)))
--**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
++(((
++[Alarm, Calculate Flag, MOD, Total pulse or Last Pulse,** **Water Flow Value, TIME]
++)))
--**Poll Message Flag**: 1: This message is a poll message reply.
--* Poll Message Flag is set to 1.
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:04:54],
++)))
--* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:05:49],
++)))
--For example, in US915 band, the max payload for different DR is:
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:06:49],
++)))
--**a) DR0:** max is 11 bytes so one entry of data
++(((
++[FALSE,0,0,0,0.0,2022-04-01 08:07:49],
++)))
--**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
++(((
++[FALSE,0,0,277,0.6,2022-04-01 08:08:49],
++)))
--**c) DR2:** total payload includes 11 entries of data
++(((
++[FALSE,0,0,287,0.6,2022-04-01 08:10:38],
++)))
--**d) DR3: **total payload includes 22 entries of data.
++[[image:1652926777796-267.png||_mstalt="300183" height="279" width="724"]]
--If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0
++== 2.4 Payload Decoder file ==
--**Example:**
--If S31x-LB has below data inside Flash:
++In TTN, use can add a custom payload so it shows friendly reading
--[[image:1682646494051-944.png]]
++In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
--If user sends below downlink command:  3160065F9760066DA705
--Where : Start time: 60065F97 = time 21/1/19 04:27:03
++== 2.5 Datalog Feature ==
--             Stop time: 60066DA7= time 21/1/19 05:27:03
++Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, CPL03-LB will store the reading for future retrieving purposes.
--**S31x-LB will uplink this payload.**
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]
++=== 2.5.1 Ways to get datalog via LoRaWAN ===
--(((
--__**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E
--)))
--(((
--Where the first 11 bytes is for the first entry:
--)))
++Set PNACKMD=1, CPL03-LB will wait for ACK for every uplink, when there is no LoRaWAN network,CPL03-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
--(((
--7FFF089801464160065F97
++* (((
++a) CPL03-LB will do an ACK check for data records sending to make sure every data arrive server.
  )))
--
--(((
--**Ext sensor data**=0x7FFF/100=327.67
++* (((
++b) CPL03-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but CPL03-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if CPL03-LB gets a ACK, CPL03-LB will consider there is a network connection and resend all NONE-ACK messages.
  )))
++Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
++
++
++=== 2.5.2 Unix TimeStamp ===
++
++
++CPL03-LB uses Unix TimeStamp format based on
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
++
++User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
++
++Below is the converter example
++
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
++
++
++So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
++
++
++=== 2.5.3 Set Device Time ===
++
++
++User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
++
++Once CPL03-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to CPL03-LB. If CPL03-LB fails to get the time from the server, CPL03-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
++
++(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
++
++
++=== 2.5.4 Poll sensor value ===
++
++
++Users can poll sensor values based on timestamps. Below is the downlink command.
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:425.818px" %)
++|(% colspan="4" style="background-color:#d9e2f3; color:#0070c0; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
++|(% style="width:58px" %)**1byte**|(% style="width:127px" %)**4bytes**|(% style="width:124px" %)**4bytes**|(% style="width:114px" %)**1byte**
++|(% style="width:58px" %)31|(% style="width:127px" %)Timestamp start|(% style="width:124px" %)Timestamp end|(% style="width:114px" %)Uplink Interval
++
  (((
--**Temp**=0x088E/100=22.00
++Timestamp start and Timestamp end-use Unix TimeStamp format as mentioned above. Devices will reply with all data logs during this period, using the uplink interval.
  )))
  (((
--**Hum**=0x014B/10=32.6
++For example, downlink command [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/image-20220518162852-1.png?rev=1.1||alt="image-20220518162852-1.png"]]
  )))
  (((
--**poll message flag & Ext**=0x41,means reply data,Ext=1
++Is to check 2021/11/12 12:00:00 to 2021/11/12 15:00:00's data
  )))
  (((
--**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03
++Uplink Internal =5s，means CPL03-LB will send one packet every 5s. range 5~~255s.
  )))
--(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
--
--== 2.6 Temperature Alarm Feature ==
--
--
--S31x-LB work flow with Alarm feature.
--
--
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]
--
--
  == 2.7 Frequency Plans ==
--The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
++The CPL03-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
--= 3. Configure S31x-LB =
++= 3. Configure CPL03-LB =
  == 3.1 Configure Methods ==
--S31x-LB supports below configure method:
++CPL03-LB supports below configure method:
  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
--
--
  == 3.2 General Commands ==
@@ -555,21 +555,25 @@
  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
--== 3.3 Commands special design for S31x-LB ==
++== 3.3 Commands special design for CPL03-LB ==
--These commands only valid for S31x-LB, as below:
++These commands only valid for CPL03-LB, as below:
  === 3.3.1 Set Transmit Interval Time ===
++(((
  Feature: Change LoRaWAN End Node Transmit Interval.
++)))
++(((
  (% style="color:blue" %)**AT Command: AT+TDC**
++)))
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**
++|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
  |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
  OK
@@ -580,20 +580,47 @@
  Set transmit interval to 60000ms = 60 seconds
  )))
++(((
  (% style="color:blue" %)**Downlink Command: 0x01**
++)))
++(((
  Format: Command Code (0x01) followed by 3 bytes time value.
++)))
++(((
  If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
++)))
--* Example 1: Downlink Payload: 0100001E       ~/~/  Set Transmit Interval (TDC) = 30 seconds
--* Example 2: Downlink Payload: 0100003C       ~/~/  Set Transmit Interval (TDC) = 60 seconds
++* (((
++Example 1: Downlink Payload: 0100001E       ~/~/ Set Transmit Interval (TDC) = 30 seconds
++)))
++* (((
++Example 2: Downlink Payload: 0100003C      ~/~/ Set Transmit Interval (TDC) = 60 seconds
++
++)))
--=== 3.3.2 Get Device Status ===
++=== 3.3.2 Quit AT Command ===
++Feature: Quit AT Command mode, so user needs to input the password again before using AT Commands.
++
++(% style="color:blue" %)**AT Command: AT+DISAT**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:452px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 198px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 99px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:155px" %)AT+DISAT|(% style="width:198px" %)Quit AT Commands mode|(% style="width:96px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++No downlink command for this feature.
++
++
++=== 3.3.3 Get Device Status ===
++
++
  Send a LoRaWAN downlink to ask device send Alarm settings.
  (% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
@@ -601,91 +601,202 @@
  Sensor will upload Device Status via FPORT=5. See payload section for detail.
--=== 3.3.3 Set Temperature Alarm Threshold ===
++=== 3.3.4 Enable / Disable Alarm ===
--* (% style="color:blue" %)**AT Command:**
++Feature: Enable/Disable Alarm for open/close event. Default value 0.
--(% style="color:#037691" %)**AT+SHTEMP=min,max**
++(% style="color:blue" %)**AT Command:**
--* When min=0, and max≠0, Alarm higher than max
--* When min≠0, and max=0, Alarm lower than min
--* When min≠0 and max≠0, Alarm higher than max or lower than min
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
++|(% style="background-color:#d9e2f3; color:#0070c0; width:154px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:278px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0; width:88px" %)**Response**
++|(% style="width:154px" %)AT+DISALARM=1|(% style="width:278px" %)End node will only send packets in TDC time.|OK
++|(% style="width:154px" %)AT+DISALARM=0|(% style="width:278px" %)End node will send packets in TDC time or status change for door sensor|OK
--Example:
++(% style="color:blue" %)**Downlink Command:**
--   AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
++**0xA7 01**     ~/~/  Same As AT+DISALARM=1
--* (% style="color:blue" %)**Downlink Payload:**
++**0xA7 00    ** ~/~/  Same As AT+DISALARM=0
--(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%)     ~/~/ Set AT+SHTEMP=0,30
--(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
++=== 3.3.5 Alarm Base on Timeout ===
--=== 3.3.4 Set Humidity Alarm Threshold ===
++(((
++CPL03-LB can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:
++)))
--* (% style="color:blue" %)**AT Command:**
++(((
++(% style="color:#4f81bd" %)**1. Keep Status: Status to be monitor**
++)))
--(% style="color:#037691" %)**AT+SHHUM=min,max**
++(((
++**Keep Status = 1**: Monitor Close to Open event
++)))
--* When min=0, and max≠0, Alarm higher than max
--* When min≠0, and max=0, Alarm lower than min
--* When min≠0 and max≠0, Alarm higher than max or lower than min
++(((
++**Keep Status = 0**: Monitor Open to Close event
++)))
--Example:
--   AT+SHHUM=70,0      ~/~/ Alarm when humidity lower than 70%.
++(((
++(% style="color:#4f81bd" %)**2. Keep Time: Timeout to send an Alarm**
++)))
--* (% style="color:blue" %)**Downlink Payload:**
++(((
++Range 0 ~~ 65535(0xFFFF) seconds.
++)))
--(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)         ~/~/ Set AT+SHTHUM=70,0
++(((
++If** keep time = 0**, Disable Alarm Base on Timeout feature.
++)))
--(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
++(((
++If **keep time > 0**, device will monitor the keep status event and send an alarm when status doesn’t change after timeout.
++)))
--=== 3.3.5 Set Alarm Interval ===
++(((
++(% style="color:#4f81bd" %)**AT Command**(%%) to configure:
++)))
++(((
++(% style="color:blue" %)**AT+TTRIG=1,30**(%%)   ~-~-> When the **Keep Status** change from connect to disconnect, and device remains in disconnect status for more than 30 seconds. CPL03-LB will send an uplink packet, the [[Alarm bit>>||anchor="H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
++)))
--The shortest time of two Alarm packet. (unit: min)
++(((
++(% style="color:blue" %)**AT+TTIG=0,0 **(%%)      ~-~-> Default Value, disable timeout Alarm.
++)))
--* (% style="color:blue" %)**AT Command:**
--(% style="color:#037691" %)**AT+ATDC=30** (%%)      ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
++(((
++(% style="color:#4f81bd" %)**Downlink Command**(%%) to configure:
++)))
--* (% style="color:blue" %)**Downlink Payload:**
++(((
++**Command: 0xA9 aa bb cc**
++)))
--(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
++(((
++**A9: **Command Type Code
++)))
++(((
++**aa: **status to be monitored
++)))
--=== 3.3.6 Get Alarm settings ===
++(((
++**bb cc: **timeout.
++)))
--Send a LoRaWAN downlink to ask device send Alarm settings.
++(((
++If user send 0xA9 01 00 1E: equal to AT+TTRIG=1,30
++)))
--* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
++(((
++Or
++)))
--**Example:**
++(((
++0xA9 00 00 00: Equal to AT+TTRIG=0,0. Disable timeout Alarm.
++)))
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/1655948182791-225.png?rev=1.1||alt="1655948182791-225.png"]]
++=== 3.3.6 Clear Flash Record ===
--**Explain:**
--* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
++Feature: Clear flash storage for data log feature.
++(% style="color:blue" %)**AT Command: AT+CLRDTA**
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
++|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 169px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 174px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:157px" %)AT+CLRDTA|(% style="width:169px" %)Clear flash storage for data log feature.|Clear all stored sensor data… OK
--=== 3.3.7 Set Interrupt Mode ===
++(((
++(% style="color:blue" %)**Downlink Command:**
++)))
++(((
++* **Example**: 0xA301     ~/~/  Same as AT+CLRDTA
++)))
--Feature, Set Interrupt mode for GPIO_EXIT.
++
++=== 3.3.7 Set trigger mode ===
++
++
++Feature: Set the trigger interrupt mode.
++
++(% style="color:blue" %)**AT Command: AT+TTRMOD**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:495px" %)
++|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 246px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 92px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:157px" %)(((
++AT+TTRMOD=1
++)))|(% style="width:156px" %)Count and trigger from open to close (rising edge)|(% style="width:89px" %)(((
++(((
++OK
++)))
++)))
++|(% style="width:157px" %)(((
++AT+TTRMOD=0
++)))|(% style="width:156px" %)Count and trigger from close to open (falling edge)|(% style="width:89px" %)(((
++OK
++)))
++
++(% style="color:blue" %)**Downlink Command:**
++
++* **Example**: 0xA401       ~/~/  Same as AT+ TTRMOD =1
++
++=== 3.3.8 Set the calculate flag ===
++
++
++Feature: Set the calculate flag
++
++(% style="color:blue" %)**AT Command: AT+CALCFLAG**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:461px" %)
++|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 193px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:158px" %)AT+CALCFLAG =1|(% style="width:192px" %)Set the calculate flag to 1.|(% style="width:109px" %)OK
++|(% style="width:158px" %)AT+CALCFLAG =2|(% style="width:192px" %)Set the calculate flag to 2.|(% style="width:109px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++* **Example**: 0XA501         ~/~/  Same as AT+CALCFLAG =1
++
++=== 3.3.9 Set count number ===
++
++
++Feature: Manually set the count number
++
++(% style="color:blue" %)**AT Command: AT+SETCNT**
++
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:479px" %)
++|=(% style="width: 160px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 223px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 96px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:160px" %)AT+ SETCNT =0|(% style="width:221px" %)Set the count number to 0.|(% style="width:95px" %)OK
++|(% style="width:160px" %)AT+ SETCNT =100|(% style="width:221px" %)Set the count number to 100.|(% style="width:95px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++* **Example**: 0xA6000001      ~/~/  Same as AT+ SETCNT =1
++
++* **Example**: 0xA6000064      ~/~/  Same as AT+ SETCNT =100
++
++=== 3.3.10 Set Interrupt Mode ===
++
++
++Feature, Set Interrupt mode for PA8 of pin.
++
++When AT+INTMOD=0 is set, PA8 is used as a digital input port.
++
  (% style="color:blue" %)**AT Command: AT+INTMOD**
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
  |(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
  OK
@@ -706,14 +706,42 @@
  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
  * Example 1: Downlink Payload: 06000000       ~/~/  Turn off interrupt mode
++
  * Example 2: Downlink Payload: 06000003      ~/~/   Set the interrupt mode to rising edge trigger
++=== 3.3.11 Set Power Output Duration ===
++Control the output duration 5V . Before each sampling, device will
++
++~1. first enable the power output to external sensor,
++
++2. keep it on as per duration, read sensor value and construct uplink payload
++
++3. final, close the power output.
++
++(% style="color:blue" %)**AT Command: AT+5VT**
++
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
++OK
++|(% style="width:154px" %)AT+5VT=500|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
++
++(% style="color:blue" %)**Downlink Command: 0x07**
++
++Format: Command Code (0x07) followed by 2 bytes.
++
++The first and second bytes are the time to turn on.
++
++* Example 1: Downlink Payload: 070000     **~-~-->**   AT+5VT=0
++
++* Example 2: Downlink Payload: 0701F4      **~-~-->**  AT+5VT=500
++
  = 4. Battery & Power Consumption =
--S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++CPL03-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
@@ -722,32 +722,36 @@
  (% class="wikigeneratedid" %)
--User can change firmware S31x-LB to:
++User can change firmware CPL03-LB to:
  * Change Frequency band/ region.
++
  * Update with new features.
++
  * Fix bugs.
  Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
--
  Methods to Update Firmware:
  * (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
++
  * Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
++= 6. FAQ =
++== 6.1  AT Commands input doesn't work ==
--= 6. FAQ =
++In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
  = 7. Order Info =
--Part Number: (% style="color:blue" %)**S31-LB-XX  / S31B-LB-XX**
++Part Number: (% style="color:blue" %)**CPL03-LB-XXX**
--(% style="color:red" %)**XX**(%%): The default frequency band
++(% style="color:red" %)**XXX**(%%): The default frequency band
  * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
@@ -765,14 +765,12 @@
  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
--
--
  = 8. Packing Info =
  (% style="color:#037691" %)**Package Includes**:
--* S31x-LB LoRaWAN Temperature & Humidity Sensor
++* CPL03-LB LoRaWAN Pulse/Contact Sensor
  (% style="color:#037691" %)**Dimension and weight**:
@@ -784,8 +784,6 @@
  * Weight / pcs : g
--
--
  = 9. Support =

image-20230523174230-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+605.9 KB

Content

image-20230524105433-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+121.4 KB

Content

image-20230524105747-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+223.2 KB

Content

image-20230524110125-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+194.1 KB

Content

image-20230524110211-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+110.1 KB

Content

image-20230524114302-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+12.0 KB

Content

image-20230524114654-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+17.8 KB

Content

image-20230524114826-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+82.3 KB

Content

image-20230524144422-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+34.9 KB

Content

image-20230524144456-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+33.9 KB

Content

image-20230527093155-1.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+9.3 KB

Content

image-20230527093214-2.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+14.7 KB

Content

image-20230530084138-1.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.1 MB

Content

image-20230530084608-2.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.1 MB

Content

image-20230530111051-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+85.1 KB

Content

image-20230530111412-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+85.0 KB

Content

image-20230530135919-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+87.6 KB

Content

image-20230530135929-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+87.6 KB

Content

image-20230530140053-1.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.3 MB

Content