Skip to Content
Last modified by Mengting Qiu on 2023/12/14 11:15
From version 39.7
edited by Xiaoling
on 2023/05/19 17:49
Change comment: There is no comment for this version
To version 55.1
edited by Saxer Lin
on 2023/05/24 11:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.Saxer
Content
... ... @@ -48,8 +48,6 @@
48 48  * Downlink to change configure
49 49  * 8500mAh Battery for long term use
50 50  
51 -
52 -
53 53  == 1.3 Specification ==
54 54  
55 55  
... ... @@ -92,8 +92,6 @@
92 92  * Sleep Mode: 5uA @ 3.3v
93 93  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
94 94  
95 -
96 -
97 97  == 1.4 Sleep mode and working mode ==
98 98  
99 99  
... ... @@ -121,8 +121,6 @@
121 121  )))
122 122  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
123 123  
124 -
125 -
126 126  == 1.6 BLE connection ==
127 127  
128 128  
... ... @@ -138,12 +138,19 @@
138 138  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
139 139  
140 140  
141 -== 1.7  Hardware Variant ==
135 +== 1.7 Pin Definitions ==
142 142  
137 +[[image:image-20230523174230-1.png]]
143 143  
139 +
140 +== 1.8 Hardware Variant ==
141 +
142 +
144 144  (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
145 145  |=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 218px;background-color:#D9E2F3;color:#0070C0" %)Probe Info
146 -|(% style="width:102px" %)S31-LB|(% style="width:190px" %)[[image:S31.jpg]]|(% style="width:297px" %)(((
145 +|(% style="width:102px" %)(((
146 +S31-LB
147 +)))|(% style="width:190px" %)[[image:S31.jpg]]|(% style="width:297px" %)(((
147 147  1 x SHT31 Probe
148 148  
149 149  Cable Length : 2 meters
... ... @@ -150,7 +150,9 @@
150 150  
151 151  
152 152  )))
153 -|(% style="width:102px" %)S31B-LB|(% style="width:190px" %)[[image:S31B.jpg]]|(% style="width:297px" %)(((
154 +|(% style="width:102px" %)(((
155 +S31B-LB
156 +)))|(% style="width:190px" %)[[image:S31B.jpg]]|(% style="width:297px" %)(((
154 154  1 x SHT31 Probe
155 155  
156 156  Installed in device.
... ... @@ -160,7 +160,7 @@
160 160  
161 161  
162 162  
163 -== 1.8 Mechanical ==
166 +== 1.9 Mechanical ==
164 164  
165 165  
166 166  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
... ... @@ -307,19 +307,25 @@
307 307  
308 308  Sensor Data is uplink via FPORT=2
309 309  
310 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
313 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:700px" %)
311 311  |=(% style="width: 90px;background-color:#D9E2F3" %)(((
312 312  **Size(bytes)**
313 -)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2
316 +)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width: 194px; background-color: rgb(217, 226, 243);" %)1|=(% style="width: 106px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 97px; background-color: rgb(217, 226, 243);" %)2
314 314  |(% style="width:99px" %)**Value**|(% style="width:69px" %)(((
315 315  [[Battery>>||anchor="HBattery"]]
316 316  )))|(% style="width:130px" %)(((
317 317  [[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
318 -)))|(% style="width:91px" %)(((
319 -[[Alarm Flag>>||anchor="HAlarmFlag26MOD"]]
320 -)))|(% style="width:103px" %)(((
321 +)))|(% style="width:194px" %)(((
322 +[[Alarm Flag&>>Alarm Flag& MOD& Level of PA8]]
323 +
324 +[[MOD&>>Alarm Flag& MOD& Level of PA8]]
325 +
326 +[[Level of PA8>>Alarm Flag& MOD& Level of PA8]]
327 +
328 +
329 +)))|(% style="width:106px" %)(((
321 321  [[Temperature>>||anchor="HTemperature"]]
322 -)))|(% style="width:80px" %)(((
331 +)))|(% style="width:97px" %)(((
323 323  [[Humidity>>||anchor="HHumidity"]]
324 324  )))
325 325  
... ... @@ -350,17 +350,21 @@
350 350  Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
351 351  
352 352  
353 -==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
362 +==== (% style="color:#4472c4" %)**Alarm Flag & MOD & Level of PA8**(%%) ====
354 354  
355 355  
356 356  **Example:**
357 357  
358 -If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message
367 +If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
359 359  
360 -If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm
369 +If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm.
361 361  
362 -If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message
371 +If payload & 0x80>>7 = 0x01  **~-~->** The PA8 is low level.
363 363  
373 +If payload & 0x80>>7 =0x00  **~-~->** The PA8 is high level.
374 +
375 +If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message.
376 +
364 364  If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
365 365  
366 366  
... ... @@ -371,7 +371,7 @@
371 371  
372 372  In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
373 373  
374 -[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
387 +[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
375 375  
376 376  
377 377  == 2.5 Datalog Feature ==
... ... @@ -385,8 +385,12 @@
385 385  
386 386  Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
387 387  
388 -* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
389 -* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
401 +* (((
402 +a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
403 +)))
404 +* (((
405 +b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
406 +)))
390 390  
391 391  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
392 392  
... ... @@ -427,18 +427,35 @@
427 427  
428 428  **Retrieval data payload:**
429 429  
430 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
447 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:680px" %)
431 431  |=(% style="width: 80px;background-color:#D9E2F3" %)(((
432 432  **Size(bytes)**
433 -)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**
434 -|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((
435 -Temp_Black
436 -)))|(% style="width:51px" %)Temp_White|(% style="width:89px" %)Temp_ Red or Temp _White|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]
450 +)))|=(% style="width: 68px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 104px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 87px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 178px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 137px; background-color: rgb(217, 226, 243);" %)**4**
451 +|(% style="width:103px" %)**Value**|(% style="width:68px" %)(((
452 +ignore
453 +)))|(% style="width:104px" %)(((
454 +(((
455 +Humidity
456 +)))
437 437  
438 -**Poll message flag & Ext:**
458 +(((
459 +
460 +)))
461 +)))|(% style="width:87px" %)(((
462 +Temperature
463 +)))|(% style="width:178px" %)(((
464 +Poll message flag &
439 439  
440 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]
466 +Alarm Flag&
441 441  
468 +Level of PA8
469 +)))|(% style="width:137px" %)Unix Time Stamp
470 +
471 +**Poll message flag & Alarm Flag & Level of PA8:**
472 +
473 +[[image:image-20230524114302-1.png||height="115" width="736"]]
474 +
475 +
442 442  **No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
443 443  
444 444  **Poll Message Flag**: 1: This message is a poll message reply.
... ... @@ -459,26 +459,26 @@
459 459  
460 460  If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
461 461  
462 -
463 463  **Example:**
464 464  
465 465  If S31x-LB has below data inside Flash:
466 466  
467 -[[image:1682646494051-944.png]]
500 +[[image:image-20230524114654-2.png]]
468 468  
469 -If user sends below downlink command: 3160065F9760066DA705
470 470  
471 -Where : Start time: 60065F97 = time 21/1/19 04:27:03
503 +If user sends below downlink command: 31646D84E1646D856C05
472 472  
473 - Stop time: 60066DA7= time 21/1/19 05:27:03
505 +Where : Start time: 646D84E1 = time 23/5/24 03:30:41
474 474  
507 + Stop time: 646D856C= time 23/5/24 03:33:00
475 475  
509 +
476 476  **S31x-LB will uplink this payload.**
477 477  
478 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]
512 +[[image:image-20230524114826-3.png]]
479 479  
480 480  (((
481 -__**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E
515 +00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
482 482  )))
483 483  
484 484  (((
... ... @@ -486,30 +486,26 @@
486 486  )))
487 487  
488 488  (((
489 -7FFF089801464160065F97
523 +00 00 02 36 01 10 40 64 6D 84 E1
490 490  )))
491 491  
492 492  (((
493 -**Ext sensor data**=0x7FFF/100=327.67
527 +**Hum**=0x0236/10=56.6
494 494  )))
495 495  
496 496  (((
497 -**Temp**=0x088E/100=22.00
531 +**Temp**=0x0110/10=27.2
498 498  )))
499 499  
500 500  (((
501 -**Hum**=0x014B/10=32.6
535 +**poll message flag & Alarm Flag & Level of PA8**=0x40,means reply data,sampling uplink message,the PA8 is low level.
502 502  )))
503 503  
504 504  (((
505 -**poll message flag & Ext**=0x41,means reply data,Ext=1
539 +**Unix time** is 0x646D84E1=1684899041s=23/5/24 03:30:41
506 506  )))
507 507  
508 -(((
509 -**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03
510 -)))
511 511  
512 -
513 513  (% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
514 514  
515 515  == 2.6 Temperature Alarm Feature ==
... ... @@ -518,9 +518,10 @@
518 518  S31x-LB work flow with Alarm feature.
519 519  
520 520  
521 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]
551 +[[image:image-20230524110125-3.png||height="768" width="1115"]]
522 522  
523 523  
554 +
524 524  == 2.7 Frequency Plans ==
525 525  
526 526  
... ... @@ -540,8 +540,6 @@
540 540  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
541 541  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
542 542  
543 -
544 -
545 545  == 3.2 General Commands ==
546 546  
547 547  
... ... @@ -589,8 +589,6 @@
589 589  * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
590 590  * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
591 591  
592 -
593 -
594 594  === 3.3.2 Get Device Status ===
595 595  
596 596  
... ... @@ -668,20 +668,19 @@
668 668  
669 669  **Example:**
670 670  
671 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/1655948182791-225.png?rev=1.1||alt="1655948182791-225.png"]]
698 +[[image:image-20230524110211-4.png]]
672 672  
673 -
674 674  **Explain:**
675 675  
676 676  * Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
677 677  
678 -
679 -
680 680  === 3.3.7 Set Interrupt Mode ===
681 681  
682 682  
683 -Feature, Set Interrupt mode for GPIO_EXIT.
707 +Feature, Set Interrupt mode for PA8 of pin.
684 684  
709 +When AT+INTMOD=0 is set, PA8 is used as a digital input port.
710 +
685 685  (% style="color:blue" %)**AT Command: AT+INTMOD**
686 686  
687 687  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
... ... @@ -708,8 +708,34 @@
708 708  * Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
709 709  * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
710 710  
737 +=== 3.3.8 Set Power Output Duration ===
711 711  
712 712  
740 +Control the output duration 5V . Before each sampling, device will
741 +
742 +~1. first enable the power output to external sensor,
743 +
744 +2. keep it on as per duration, read sensor value and construct uplink payload
745 +
746 +3. final, close the power output.
747 +
748 +(% style="color:blue" %)**AT Command: AT+5VT**
749 +
750 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
751 +|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
752 +|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
753 +OK
754 +|(% style="width:154px" %)AT+5VT=500|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
755 +
756 +(% style="color:blue" %)**Downlink Command: 0x07**
757 +
758 +Format: Command Code (0x07) followed by 2 bytes.
759 +
760 +The first and second bytes are the time to turn on.
761 +
762 +* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
763 +* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
764 +
713 713  = 4. Battery & Power Consumption =
714 714  
715 715  
... ... @@ -736,8 +736,6 @@
736 736  * (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
737 737  * Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
738 738  
739 -
740 -
741 741  = 6. FAQ =
742 742  
743 743  
... ... @@ -765,8 +765,6 @@
765 765  
766 766  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
767 767  
768 -
769 -
770 770  = 8. ​Packing Info =
771 771  
772 772  
... ... @@ -784,8 +784,6 @@
784 784  
785 785  * Weight / pcs : g
786 786  
787 -
788 -
789 789  = 9. Support =
790 790  
791 791  
image-20230523174230-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +605.9 KB
Content
image-20230524105433-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +121.4 KB
Content
image-20230524105747-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +223.2 KB
Content
image-20230524110125-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +194.1 KB
Content
image-20230524110211-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +110.1 KB
Content
image-20230524114302-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +12.0 KB
Content
image-20230524114654-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +17.8 KB
Content
image-20230524114826-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +82.3 KB
Content