Skip to Content
Last modified by Mengting Qiu on 2023/12/14 11:15
From version 30.1
edited by Ellie Zhang
on 2023/05/06 14:39
Change comment: There is no comment for this version
To version 60.15
edited by Xiaoling
on 2023/05/27 11:12
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Ellie
1 +XWiki.Xiaoling
Content
... ... @@ -4,7 +4,7 @@
4 4  
5 5  
6 6  
7 -**目录：**
7 +**Table of Contents：**
8 8  
9 9  {{toc/}}
10 10  
... ... @@ -13,46 +13,29 @@
13 13  
14 14  
15 15  
16 -= 一、简介 =
16 += 1. Introduction =
17 17  
18 -== 1.1 什么是 S31x-LB LoRaWAN 温湿度传感器 ==
18 +== 1.1 What is S31x-LB LoRaWAN Temperature & Humidity Sensor ==
19 19  
20 20  
21 -(((
22 -Dragino S31x-LB 是 用于物联网解决方案的(% style="color:blue" %)**LoRaWAN 温度和湿度传感器。**(%%)用于(% style="color:blue" %)**精确测量周围环境温度和相对空气湿度**(%%)，然后通过LoRaWAN无线协议上传到物联网服务器。
23 -)))
21 +The Dragino S31x-LB is a (% style="color:blue" %)**LoRaWAN Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)**surrounding environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via LoRaWAN wireless protocol.
24 24  
25 -(((
26 -S31x-LB采用的温湿度传感器为SHT31，是Sensirion的全校准、线性化、温度补偿数字输出，具有很强的可靠性和长期稳定性。SHT31 固定在(% style="color:blue" %)**防水防冷凝外壳**(%%)中，可长期使用。
27 -)))
23 +The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
28 28  
29 -(((
30 30  The LoRa wireless technology used in S31x-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
31 -)))
32 32  
33 -(((
34 -S31x-LB supports (% style="color:blue" %)**Temperature & Humdity alarm feature,**(%%) user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
35 -)))
27 +S31x-LB supports (% style="color:blue" %)**Temperature & Humdity alarm feature**(%%), user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
36 36  
37 -(((
38 -S31x-LB has max 3 probes which measure maximum 3 temperature points.
39 -)))
29 +S31x-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
40 40  
41 -(((
42 -S31x-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
43 -)))
31 +S31x-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
44 44  
45 -(((
46 -S31x-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
47 -)))
48 -
49 -(((
50 50  Each S31x-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
51 -)))
52 52  
53 53  
54 54  == 1.2 ​Features ==
55 55  
38 +
56 56  * LoRaWAN 1.0.3 Class A
57 57  * Ultra-low power consumption
58 58  * External 3 meters SHT31 probe (For S31-LB)
... ... @@ -149,12 +149,19 @@
149 149  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
150 150  
151 151  
152 -== 1.7  Hardware Variant ==
135 +== 1.7 Pin Definitions ==
153 153  
137 +[[image:image-20230523174230-1.png]]
154 154  
155 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
139 +
140 +== 1.8 Hardware Variant ==
141 +
142 +
143 +(% border="1" cellspacing="5" style="width:510px" %)
156 156  |=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 218px;background-color:#D9E2F3;color:#0070C0" %)Probe Info
157 -|(% style="width:102px" %)S31-LB|(% style="width:190px" %) |(% style="width:297px" %)(((
145 +|(% style="width:102px" %)(((
146 +S31-LB
147 +)))|(% style="width:190px" %)[[image:image-20230527093214-2.jpeg]]|(% style="width:297px" %)(((
158 158  1 x SHT31 Probe
159 159  
160 160  Cable Length : 2 meters
... ... @@ -161,7 +161,9 @@
161 161  
162 162  
163 163  )))
164 -|(% style="width:102px" %)S31B-LB|(% style="width:190px" %) |(% style="width:297px" %)(((
154 +|(% style="width:102px" %)(((
155 +S31B-LB
156 +)))|(% style="width:190px" %)[[image:image-20230527093155-1.jpeg]]|(% style="width:297px" %)(((
165 165  1 x SHT31 Probe
166 166  
167 167  Installed in device.
... ... @@ -171,7 +171,7 @@
171 171  
172 172  
173 173  
174 -== 1.8 Mechanical ==
166 +== 1.9 Mechanical ==
175 175  
176 176  
177 177  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
... ... @@ -257,7 +257,7 @@
257 257  
258 258  Example parse in TTNv3
259 259  
260 -[[image:image-20230421171614-1.png||alt="图片-20230421171614-1.png"]]
252 +[[image:image-20230524144422-1.png||height="174" width="1080"]]
261 261  
262 262  
263 263  (% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
... ... @@ -319,21 +319,24 @@
319 319  Sensor Data is uplink via FPORT=2
320 320  
321 321  (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
322 -|=(% style="width: 90px;background-color:#D9E2F3" %)(((
314 +|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
323 323  **Size(bytes)**
324 -)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2
325 -|(% style="width:99px" %)**Value**|(% style="width:69px" %)(((
326 -[[Battery>>||anchor="HBattery:"]]
316 +)))|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)4|=(% style="width: 150px; background-color: #D9E2F3;color:#0070C0" %)1|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)**2**|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2
317 +|(% style="width:99px" %)Value|(% style="width:69px" %)(((
318 +Battery
327 327  )))|(% style="width:130px" %)(((
328 -[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
329 -)))|(% style="width:91px" %)(((
330 -[[Alarm Flag>>||anchor="HAlarmFlag26MOD:"]]
331 -)))|(% style="width:103px" %)(((
332 -[[Temperature>>||anchor="HTemperature:"]]
333 -)))|(% style="width:80px" %)(((
334 -[[Humidity>>||anchor="HHumidity:"]]
320 +Unix TimeStamp
321 +)))|(% style="width:194px" %)(((
322 +Alarm Flag & MOD& Level of PA8
323 +)))|(% style="width:106px" %)(((
324 +Temperature
325 +)))|(% style="width:97px" %)(((
326 +Humidity
335 335  )))
336 336  
329 +[[image:image-20230524144456-2.png||height="180" width="1142"]]
330 +
331 +
337 337  ==== (% style="color:#4472c4" %)**Battery**(%%) ====
338 338  
339 339  Sensor Battery Level.
... ... @@ -361,17 +361,21 @@
361 361  Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
362 362  
363 363  
364 -==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
359 +==== (% style="color:#4472c4" %)**Alarm Flag & MOD & Level of PA8**(%%) ====
365 365  
366 366  
367 367  **Example:**
368 368  
369 -If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message
364 +If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
370 370  
371 -If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm
366 +If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm.
372 372  
373 -If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message
368 +If payload & 0x80>>7 = 0x01  **~-~->** The PA8 is low level.
374 374  
370 +If payload & 0x80>>7 =0x00  **~-~->** The PA8 is high level.
371 +
372 +If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message.
373 +
375 375  If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
376 376  
377 377  
... ... @@ -382,7 +382,7 @@
382 382  
383 383  In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
384 384  
385 -[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
384 +[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
386 386  
387 387  
388 388  == 2.5 Datalog Feature ==
... ... @@ -394,15 +394,20 @@
394 394  === 2.5.1 Ways to get datalog via LoRaWAN ===
395 395  
396 396  
397 -Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayloadA028FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
396 +Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
398 398  
399 -* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
400 -* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
398 +* (((
399 +a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
400 +)))
401 +* (((
402 +b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
403 +)))
401 401  
402 402  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
403 403  
404 404  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
405 405  
409 +
406 406  === 2.5.2 Unix TimeStamp ===
407 407  
408 408  
... ... @@ -416,6 +416,7 @@
416 416  
417 417  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
418 418  
423 +
419 419  So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
420 420  
421 421  
... ... @@ -436,18 +436,31 @@
436 436  
437 437  **Retrieval data payload:**
438 438  
439 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
440 -|=(% style="width: 80px;background-color:#D9E2F3" %)(((
444 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
445 +|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
441 441  **Size(bytes)**
442 -)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**
443 -|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((
444 -[[Temp_Black>>||anchor="HTemperatureBlack:"]]
445 -)))|(% style="width:51px" %)[[Temp_White>>||anchor="HTemperatureWhite:"]]|(% style="width:89px" %)[[Temp_ Red or Temp _White>>||anchor="HTemperatureREDorTemperatureWhite:"]]|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]
447 +)))|=(% style="width: 40px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 55px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 65px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 180px; background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 100px; background-color:#D9E2F3;color:#0070C0" %)**4**
448 +|(% style="width:103px" %)Value|(% style="width:68px" %)(((
449 +ignore
450 +)))|(% style="width:104px" %)(((
451 +(((
452 +Humidity
453 +)))
446 446  
447 -**Poll message flag & Ext:**
455 +(((
456 +
457 +)))
458 +)))|(% style="width:87px" %)(((
459 +Temperature
460 +)))|(% style="width:178px" %)(((
461 +Poll message flag & Alarm Flag& Level of PA8
462 +)))|(% style="width:137px" %)Unix Time Stamp
448 448  
449 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]
464 +**Poll message flag & Alarm Flag & Level of PA8:**
450 450  
466 +[[image:image-20230524114302-1.png||height="115" width="736"]]
467 +
468 +
451 451  **No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
452 452  
453 453  **Poll Message Flag**: 1: This message is a poll message reply.
... ... @@ -468,26 +468,26 @@
468 468  
469 469  If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
470 470  
471 -
472 472  **Example:**
473 473  
474 474  If S31x-LB has below data inside Flash:
475 475  
476 -[[image:1682646494051-944.png]]
493 +[[image:image-20230524114654-2.png]]
477 477  
478 -If user sends below downlink command: 3160065F9760066DA705
479 479  
480 -Where : Start time: 60065F97 = time 21/1/19 04:27:03
496 +If user sends below downlink command: 31646D84E1646D856C05
481 481  
482 - Stop time: 60066DA7= time 21/1/19 05:27:03
498 +Where : Start time: 646D84E1 = time 23/5/24 03:30:41
483 483  
500 + Stop time: 646D856C= time 23/5/24 03:33:00
484 484  
502 +
485 485  **S31x-LB will uplink this payload.**
486 486  
487 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]
505 +[[image:image-20230524114826-3.png||height="448" width="1244"]]
488 488  
489 489  (((
490 -__**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E
508 +00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
491 491  )))
492 492  
493 493  (((
... ... @@ -495,30 +495,26 @@
495 495  )))
496 496  
497 497  (((
498 -7FFF089801464160065F97
516 +00 00 02 36 01 10 40 64 6D 84 E1
499 499  )))
500 500  
501 501  (((
502 -**Ext sensor data**=0x7FFF/100=327.67
520 +**Hum**=0x0236/10=56.6
503 503  )))
504 504  
505 505  (((
506 -**Temp**=0x088E/100=22.00
524 +**Temp**=0x0110/10=27.2
507 507  )))
508 508  
509 509  (((
510 -**Hum**=0x014B/10=32.6
528 +**poll message flag & Alarm Flag & Level of PA8**=0x40,means reply data,sampling uplink message,the PA8 is low level.
511 511  )))
512 512  
513 513  (((
514 -**poll message flag & Ext**=0x41,means reply data,Ext=1
532 +**Unix time** is 0x646D84E1=1684899041s=23/5/24 03:30:41
515 515  )))
516 516  
517 -(((
518 -**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03
519 -)))
520 520  
521 -
522 522  (% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
523 523  
524 524  == 2.6 Temperature Alarm Feature ==
... ... @@ -527,9 +527,10 @@
527 527  S31x-LB work flow with Alarm feature.
528 528  
529 529  
530 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]
544 +[[image:image-20230524110125-3.png||height="768" width="1115"]]
531 531  
532 532  
547 +
533 533  == 2.7 Frequency Plans ==
534 534  
535 535  
... ... @@ -608,6 +608,7 @@
608 608  
609 609  === 3.3.3 Set Temperature Alarm Threshold ===
610 610  
626 +
611 611  * (% style="color:blue" %)**AT Command:**
612 612  
613 613  (% style="color:#037691" %)**AT+SHTEMP=min,max**
... ... @@ -629,6 +629,7 @@
629 629  
630 630  === 3.3.4 Set Humidity Alarm Threshold ===
631 631  
648 +
632 632  * (% style="color:blue" %)**AT Command:**
633 633  
634 634  (% style="color:#037691" %)**AT+SHHUM=min,max**
... ... @@ -650,6 +650,7 @@
650 650  
651 651  === 3.3.5 Set Alarm Interval ===
652 652  
670 +
653 653  The shortest time of two Alarm packet. (unit: min)
654 654  
655 655  * (% style="color:blue" %)**AT Command:**
... ... @@ -670,9 +670,8 @@
670 670  
671 671  **Example:**
672 672  
673 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/1655948182791-225.png?rev=1.1||alt="1655948182791-225.png"]]
691 +[[image:image-20230524110211-4.png]]
674 674  
675 -
676 676  **Explain:**
677 677  
678 678  * Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
... ... @@ -680,12 +680,14 @@
680 680  === 3.3.7 Set Interrupt Mode ===
681 681  
682 682  
683 -Feature, Set Interrupt mode for GPIO_EXIT.
700 +Feature, Set Interrupt mode for PA8 of pin.
684 684  
702 +When AT+INTMOD=0 is set, PA8 is used as a digital input port.
703 +
685 685  (% style="color:blue" %)**AT Command: AT+INTMOD**
686 686  
687 687  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
688 -|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
707 +|=(% style="width: 155px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3" %)**Response**
689 689  |(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
690 690  0
691 691  OK
... ... @@ -708,6 +708,34 @@
708 708  * Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
709 709  * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
710 710  
730 +=== 3.3.8 Set Power Output Duration ===
731 +
732 +
733 +Control the output duration 5V . Before each sampling, device will
734 +
735 +~1. first enable the power output to external sensor,
736 +
737 +2. keep it on as per duration, read sensor value and construct uplink payload
738 +
739 +3. final, close the power output.
740 +
741 +(% style="color:blue" %)**AT Command: AT+5VT**
742 +
743 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
744 +|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
745 +|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
746 +OK
747 +|(% style="width:154px" %)AT+5VT=500|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
748 +
749 +(% style="color:blue" %)**Downlink Command: 0x07**
750 +
751 +Format: Command Code (0x07) followed by 2 bytes.
752 +
753 +The first and second bytes are the time to turn on.
754 +
755 +* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
756 +* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
757 +
711 711  = 4. Battery & Power Consumption =
712 712  
713 713  
... ... @@ -726,61 +726,61 @@
726 726  * Update with new features.
727 727  * Fix bugs.
728 728  
729 -固件和变更日志可以从以下位置下载：**[[固件下载链接>>https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
776 +Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
730 730  
731 731  
732 -更新固件的方法：
779 +Methods to Update Firmware:
733 733  
734 -* （推荐方式）无线OTA固件更新：  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
735 -* 通过 UART TTL 接口更新。**[[指令>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**。
781 +* (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
782 +* Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
736 736  
737 -= 6. 常见问题 =
784 += 6. FAQ =
738 738  
739 739  
740 740  
741 -= 7. 订单信息 =
788 += 7. Order Info =
742 742  
743 743  
744 -零件号：(% style="color:blue" %)**S31-LB-XX / S31B-LB-XX**
791 +Part Number: (% style="color:blue" %)**S31-LB-XX  / S31B-LB-XX**
745 745  
746 -(% style="color:red" %)**XX**(%%) : 默认频段
793 +(% style="color:red" %)**XX**(%%): The default frequency band
747 747  
748 -* (% style="color:red" %)**AS923**(%%) : LoRaWAN AS923 频段
795 +* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
749 749  
750 -* (% style="color:red" %)**AU915**(%%) : LoRaWAN AU915 频段
797 +* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
751 751  
752 -* (% style="color:red" %)**EU433**(%%) : LoRaWAN EU433 频段
799 +* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
753 753  
754 -* (% style="color:red" %)**EU868**(%%) : LoRaWAN EU868 频段
801 +* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
755 755  
756 -* (% style="color:red" %)**KR920**(%%) : LoRaWAN KR920 频段
803 +* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
757 757  
758 -* (% style="color:red" %)**US915**(%%) : LoRaWAN US915 频段
805 +* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
759 759  
760 -* (% style="color:red" %)**IN865**(%%) : LoRaWAN IN865 频段
807 +* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
761 761  
762 -* (% style="color:red" %)**CN470**(%%) : LoRaWAN CN470 频段
809 +* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
763 763  
764 -= 8. 包装信息 =
811 += 8. ​Packing Info =
765 765  
766 766  
767 -(% style="color:#037691" %)**套餐包括**：
814 +(% style="color:#037691" %)**Package Includes**:
768 768  
769 -* S31x-LB LoRaWAN 温湿度传感器
816 +* S31x-LB LoRaWAN Temperature & Humidity Sensor
770 770  
771 -(% style="color:#037691" %)**尺寸和重量**：
818 +(% style="color:#037691" %)**Dimension and weight**:
772 772  
773 -* 设备尺寸：cm
820 +* Device Size: cm
774 774  
775 -* 设备重量：g
822 +* Device Weight: g
776 776  
777 -* 包装尺寸/个 : cm
824 +* Package Size / pcs : cm
778 778  
779 -* 重量/个：克
826 +* Weight / pcs : g
780 780  
781 -= 9.支持 =
828 += 9. Support =
782 782  
783 783  
784 -* 周一至周五的 09:00 至 18:00 GMT+8 提供支持。由于时区不同，我们无法提供现场支持。但是，您的问题将在上述时间表中尽快得到解答。
831 +* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
785 785  
786 -* 提供尽可能多的关于您的询问的信息（产品型号、准确描述您的问题和复制它的步骤等）并发送邮件至 [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
833 +* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].
S31.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ellie
Size
... ... @@ -1,0 +1,1 @@
1 +58.7 KB
Content
S31B.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ellie
Size
... ... @@ -1,0 +1,1 @@
1 +40.5 KB
Content
image-20230523174230-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +605.9 KB
Content
image-20230524105433-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +121.4 KB
Content
image-20230524105747-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +223.2 KB
Content
image-20230524110125-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +194.1 KB
Content
image-20230524110211-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +110.1 KB
Content
image-20230524114302-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +12.0 KB
Content
image-20230524114654-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +17.8 KB
Content
image-20230524114826-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +82.3 KB
Content
image-20230524144422-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +34.9 KB
Content
image-20230524144456-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +33.9 KB
Content
image-20230527093155-1.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +9.3 KB
Content
image-20230527093214-2.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +14.7 KB
Content