Skip to Content
Last modified by Mengting Qiu on 2023/12/14 11:15
From version 116.4
edited by Xiaoling
on 2023/11/13 10:38
Change comment: There is no comment for this version
To version 82.1
edited by Xiaoling
on 2023/06/14 16:24
Change comment: Uploaded new attachment "image-20230614162359-3.png", version {1}

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -DS20L -- LoRaWAN Smart Distance Detector User Manual
1 +LDS12-LB -- LoRaWAN LiDAR ToF Distance Sensor User Manual
Content
... ... @@ -1,5 +1,5 @@
1 1  (% style="text-align:center" %)
2 -[[image:image-20231110085342-2.png||height="481" width="481"]]
2 +[[image:image-20230614153353-1.png]]
3 3  
4 4  
5 5  
... ... @@ -7,7 +7,6 @@
7 7  
8 8  
9 9  
10 -
11 11  **Table of Contents：**
12 12  
13 13  {{toc/}}
... ... @@ -19,429 +19,443 @@
19 19  
20 20  = 1. Introduction =
21 21  
22 -== 1.1 What is LoRaWAN Smart Distance Detector ==
21 +== 1.1 What is LoRaWAN LiDAR ToF Distance Sensor ==
23 23  
24 24  
25 -The Dragino (% style="color:blue" %)**DS20L is a smart distance detector**(%%) base on long-range wireless LoRaWAN technology. It uses (% style="color:blue" %)**LiDAR sensor**(%%) to detect the distance between DS20L and object, then DS20L will send the distance data to the IoT Platform via LoRaWAN. DS20L can measure range between 3cm ~~ 200cm.
24 +The Dragino LDS12-LB is a (% style="color:blue" %)**LoRaWAN LiDAR ToF (Time of Flight) Distance Sensor**(%%) for Internet of Things solution. It is capable to measure the distance to an object as close as 10 centimeters (+/- 5cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)!. The LiDAR probe uses laser induction technology for distance measurement.
26 26  
27 -DS20L allows users to send data and reach extremely long ranges via LoRaWAN. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current 
28 -consumption. It targets professional wireless sensor network applications such smart cities, building automation, and so on.
26 +The LDS12-LB can be applied to scenarios such as horizontal distance measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, etc.
29 29  
30 -DS20L has a (% style="color:blue" %)**built-in 2400mAh non-chargeable battery**(%%) for long-term use up to several years*. Users can also power DS20L with an external power source for (% style="color:blue" %)**continuous measuring and distance alarm / counting purposes.**
28 +It detects the distance between the measured object and the sensor, and uploads the value via wireless to LoRaWAN IoT Server.
31 31  
32 -DS20L is fully compatible with (% style="color:blue" %)**LoRaWAN v1.0.3 Class A protocol**(%%), it can work with a standard LoRaWAN gateway.
30 +The LoRa wireless technology used in LDS12-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
33 33  
32 +LDS12-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
34 34  
35 -[[image:image-20231110102635-5.png||height="402" width="807"]]
34 +LDS12-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
36 36  
36 +Each LDS12-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
37 37  
38 +[[image:image-20230613140115-3.png||height="453" width="800"]]
39 +
40 +
38 38  == 1.2 ​Features ==
39 39  
40 40  
41 -* LoRaWAN Class A protocol
42 -* LiDAR distance detector, range 3 ~~ 200cm
43 -* Periodically detect or continuously detect mode
44 +* LoRaWAN 1.0.3 Class A
45 +* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
46 +* Ultra-low power consumption
47 +* Liquid Level Measurement by Ultrasonic technology
48 +* Measure through container, No need to contact Liquid
49 +* Valid level range 20mm - 2000mm
50 +* Accuracy: ±(5mm+S*0.5%) (S: Measure Value)
51 +* Cable Length : 25cm
52 +* Support Bluetooth v5.1 and LoRaWAN remote configure
53 +* Support wireless OTA update firmware
44 44  * AT Commands to change parameters
45 -* Remotely configure parameters via LoRaWAN Downlink
46 -* Alarm & Counting mode
47 -* Firmware upgradable via program port or LoRa protocol
48 -* Built-in 2400mAh battery or power by external power source
55 +* Downlink to change configure
56 +* IP66 Waterproof Enclosure
57 +* 8500mAh Battery for long term use
49 49  
50 50  
51 51  == 1.3 Specification ==
52 52  
53 53  
54 -(% style="color:#037691" %)**LiDAR Sensor:**
63 +(% style="color:#037691" %)**Common DC Characteristics:**
55 55  
56 -* Operation Temperature: -40 ~~ 80 °C
57 -* Operation Humidity: 0~~99.9%RH (no Dew)
58 -* Storage Temperature: -10 ~~ 45°C
59 -* Measure Range: 3cm~~200cm @ 90% reflectivity
60 -* Accuracy: ±2cm @ (3cm~~100cm); ±5% @ (100~~200cm)
61 -* ToF FoV: ±9°, Total 18°
62 -* Light source: VCSEL
65 +* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
66 +* Operating Temperature: -40 ~~ 85°C
63 63  
68 +(% style="color:#037691" %)**LoRa Spec:**
64 64  
70 +* Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
71 +* Max +22 dBm constant RF output vs.
72 +* RX sensitivity: down to -139 dBm.
73 +* Excellent blocking immunity
65 65  
75 +(% style="color:#037691" %)**Battery:**
66 66  
67 -== 1.4 Power Consumption ==
77 +* Li/SOCI2 un-chargeable battery
78 +* Capacity: 8500mAh
79 +* Self-Discharge: <1% / Year @ 25°C
80 +* Max continuously current: 130mA
81 +* Max boost current: 2A, 1 second
68 68  
83 +(% style="color:#037691" %)**Power Consumption**
69 69  
70 -(% style="color:#037691" %)**Battery Power Mode:**
85 +* Sleep Mode: 5uA @ 3.3v
86 +* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
71 71  
72 -* Idle: 0.003 mA @ 3.3v
73 -* Max : 360 mA
74 74  
75 -(% style="color:#037691" %)**Continuously mode**:
89 +== 1.4 Suitable Container & Liquid ==
76 76  
77 -* Idle: 21 mA @ 3.3v
78 -* Max : 360 mA
79 79  
92 +* Solid Wall container such as: steel, iron, glass, ceramics, non-foaming plastics etc.
93 +* Container shape is regular, and surface is smooth.
94 +* Container Thickness:
95 +** Pure metal material.  2~~8mm, best is 3~~5mm
96 +** Pure non metal material: <10 mm
97 +* Pure liquid without irregular deposition.
80 80  
81 81  
100 +(% style="display:none" %)
82 82  
83 -= 2. Configure DS20L to connect to LoRaWAN network =
102 +== 1.5 Install LDS12-LB ==
84 84  
85 -== 2.1 How it works ==
86 86  
105 +(% style="color:blue" %)**Step 1**(%%):  ** Choose the installation point.**
87 87  
88 -The DS20L is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DS20L. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
107 +LDS12-LB (% style="color:red" %)**MUST**(%%) be installed on the container bottom middle position.
89 89  
90 -(% style="display:none" %) (%%)
109 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615091045-3.png?rev=1.1||alt="image-20220615091045-3.png"]]
91 91  
92 -== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
93 93  
112 +(((
113 +(% style="color:blue" %)**Step 2**(%%):  **Polish the installation point.**
114 +)))
94 94  
95 -Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
116 +(((
117 +For Metal Surface with paint, it is important to polish the surface, first use crude sand paper to polish the paint level , then use exquisite sand paper to polish the metal level to make it shine & smooth.
118 +)))
96 96  
97 -The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.(% style="display:none" %)
120 +[[image:image-20230613143052-5.png]]
98 98  
99 -[[image:image-20231110102635-5.png||height="402" width="807"]](% style="display:none" %)
100 100  
101 -(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DS20L.
123 +No polish needed if the container is shine metal surface without paint or non-metal container.
102 102  
103 -Each DS20L is shipped with a sticker with the default device EUI as below:
125 +[[image:image-20230613143125-6.png]]
104 104  
105 -[[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
106 106  
128 +(((
129 +(% style="color:blue" %)**Step3:   **(%%)**Test the installation point.**
130 +)))
107 107  
108 -You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
132 +(((
133 +Power on LDS12-LB, check if the blue LED is on, If the blue LED is on, means the sensor works. Then put ultrasonic coupling paste on the sensor and put it tightly on the installation point.
134 +)))
109 109  
136 +(((
137 +It is necessary to put the coupling paste between the sensor and the container, otherwise LDS12-LB won't detect the liquid level.
138 +)))
110 110  
111 -(% style="color:blue" %)**Register the device**
140 +(((
141 +After paste the LDS12-LB well, power on LDS12-LB. In the first 30 seconds of booting, device will check the sensors status and BLUE LED will show the status as below. After 30 seconds, BLUE LED will be off to save battery life.
142 +)))
112 112  
113 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]
114 114  
145 +(((
146 +(% style="color:blue" %)**LED Status:**
147 +)))
115 115  
116 -(% style="color:blue" %)**Add APP EUI and DEV EUI**
149 +* (((
150 +**Onboard LED**: When power on device, the onboard LED will fast blink 4 times which means detect the sensor well.
151 +)))
117 117  
118 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]
153 +* (((
154 +(% style="color:blue" %)**BLUE LED**(% style="color:red" %)** always ON**(%%): Sensor is power on but doesn't detect liquid. There is problem in installation point.
155 +)))
156 +* (((
157 +(% style="color:blue" %)**BLUE LED**(% style="color:red" %)** slowly blinking**(%%): Sensor detects Liquid Level, The installation point is good.
158 +)))
119 119  
160 +(((
161 +LDS12-LB will enter into low power mode at 30 seconds after system reset or power on, Blue LED will be off after that.
162 +)))
120 120  
121 -(% style="color:blue" %)**Add APP EUI in the application**
122 122  
165 +(((
166 +(% style="color:red" %)**Note :**(%%)** (% style="color:blue" %)Ultrasonic coupling paste(%%)**(% style="color:blue" %) (%%) is subjected in most shipping way. So the default package doesn't include it and user needs to purchase locally.
167 +)))
123 123  
124 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]
125 125  
170 +(((
171 +(% style="color:blue" %)**Step4:   **(%%)**Install use Epoxy ab glue.**
172 +)))
126 126  
127 -(% style="color:blue" %)**Add APP KEY**
174 +(((
175 +Prepare Eproxy AB glue.
176 +)))
128 128  
129 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
178 +(((
179 +Put Eproxy AB glue in the sensor and press it hard on the container installation point.
180 +)))
130 130  
182 +(((
183 +Reset LDS12-LB and see if the BLUE LED is slowly blinking.
184 +)))
131 131  
132 -(% style="color:blue" %)**Step 2:**(%%) Activate on DS20L
186 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615091045-8.png?width=341&height=203&rev=1.1||alt="image-20220615091045-8.png"]] [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615091045-9.png?width=284&height=200&rev=1.1||alt="image-20220615091045-9.png"]]
133 133  
134 134  
135 -Press the button for 5 seconds to activate the DS20L.
189 +(((
190 +(% style="color:red" %)**Note :**
136 136  
137 -(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
192 +(% style="color:red" %)**1:**(%%)** (% style="color:blue" %)Eproxy AB glue(%%)** needs 3~~ 5 minutes to stable attached. we can use other glue material to keep it in the position.
193 +)))
138 138  
139 -After join success, it will start to upload messages to TTN and you can see the messages in the panel.
195 +(((
196 +(% style="color:red" %)**2:**(%%)** (% style="color:blue" %)Eproxy AB glue(%%)** is subjected in most shipping way. So the default package doesn't include it and user needs to purchase locally.
197 +)))
140 140  
141 141  
142 -== 2.3 ​Uplink Payload ==
200 +== 1.6 Applications ==
143 143  
144 -=== 2.3.1 Device Status, FPORT~=5 ===
145 145  
203 +* Smart liquid control solution
146 146  
147 -Users can use the downlink command(**0x26 01**) to ask DS20L to send device configure detail, include device configure status. DS20L will uplink a payload via FPort=5 to server.
205 +* Smart liquefied gas solution
148 148  
149 -The Payload format is as below.
150 150  
151 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
152 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
153 -**Size(bytes)**
154 -)))|=(% style="width: 100px; background-color: #4F81BD;color:white;" %)**1**|=(% style="width: 100px; background-color: #4F81BD;color:white;" %)**2**|=(% style="background-color: #4F81BD;color:white; width: 100px;" %)**1**|=(% style="background-color: #4F81BD;color:white; width: 100px;" %)**1**|=(% style="background-color: #4F81BD;color:white; width: 50px;" %)**2**
155 -|(% style="width:62.5px" %)Value|(% style="width:110px" %)Sensor Model|(% style="width:48px" %)Firmware Version|(% style="width:94px" %)Frequency Band|(% style="width:91px" %)Sub-band|(% style="width:60px" %)BAT
208 +== 1.7 Precautions ==
156 156  
157 -Example parse in TTNv3
158 158  
159 -[[image:image-20230805103904-1.png||height="131" width="711"]]
211 +* At room temperature, containers of different materials, such as steel, glass, iron, ceramics, non-foamed plastics and other dense materials, have different detection blind areas and detection limit heights.
160 160  
161 -(% style="color:blue" %)**Sensor Model**(%%): For DS20L, this value is 0x24
213 +* For containers of the same material at room temperature, the detection blind zone and detection limit height are also different for the thickness of the container.
162 162  
163 -(% style="color:blue" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
215 +* When the detected liquid level exceeds the effective detection value of the sensor, and the liquid level of the liquid to be measured shakes or tilts, the detected liquid height is unstable.
164 164  
165 -(% style="color:blue" %)**Frequency Band**:
217 +(% style="display:none" %)
166 166  
167 -0x01: EU868
219 +== 1.8 Sleep mode and working mode ==
168 168  
169 -0x02: US915
170 170  
171 -0x03: IN865
222 +(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
172 172  
173 -0x04: AU915
224 +(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
174 174  
175 -0x05: KZ865
176 176  
177 -0x06: RU864
227 +== 1.9 Button & LEDs ==
178 178  
179 -0x07: AS923
180 180  
181 -0x08: AS923-1
230 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
182 182  
183 -0x09: AS923-2
184 184  
185 -0x0a: AS923-3
233 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
234 +|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
235 +|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((
236 +If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
237 +Meanwhile, BLE module will be active and user can connect via BLE to configure device.
238 +)))
239 +|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((
240 +(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
241 +(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
242 +Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
243 +)))
244 +|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
186 186  
187 -0x0b: CN470
188 188  
189 -0x0c: EU433
247 +== 1.10 BLE connection ==
190 190  
191 -0x0d: KR920
192 192  
193 -0x0e: MA869
250 +LDS12-LB support BLE remote configure.
194 194  
195 -(% style="color:blue" %)**Sub-Band**:
252 +BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
196 196  
197 -AU915 and US915:value 0x00 ~~ 0x08
254 +* Press button to send an uplink
255 +* Press button to active device.
256 +* Device Power on or reset.
198 198  
199 -CN470: value 0x0B ~~ 0x0C
258 +If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
200 200  
201 -Other Bands: Always 0x00
202 202  
203 -(% style="color:blue" %)**Battery Info**:
261 +== 1.11 Pin Definitions ==
204 204  
205 -Check the battery voltage.
263 +[[image:image-20230523174230-1.png]]
206 206  
207 -Ex1: 0x0B45 = 2885mV
208 208  
209 -Ex2: 0x0B49 = 2889mV
266 +== 1.12 Mechanical ==
210 210  
211 211  
212 -=== 2.3.2 Uplink Payload, FPORT~=2 ===
269 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
213 213  
214 214  
215 -(((
216 -DS20L will send this uplink **after** Device Status once join the LoRaWAN network successfully. And DS20L will:
272 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
217 217  
218 -periodically send this uplink every 20 minutes, this interval [[can be changed>>||anchor="H3.3.1SetTransmitIntervalTime"]].
219 219  
220 -Uplink Payload totals 11 bytes.
221 -)))
275 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
222 222  
223 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
224 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
225 -**Size(bytes)**
226 -)))|=(% style="width: 30px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 50px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 70px;background-color:#4F81BD;color:white" %)**2**|=(% style="background-color:#4F81BD;color:white; width: 80px;" %)**1**|=(% style="background-color: #4F81BD;color:white; width: 70px;" %)**1**|=(% style="background-color: #4F81BD;color:white; width: 70px;" %)**1**
227 -|(% style="width:62.5px" %)Value|(% style="width:62.5px" %)[[BAT>>||anchor="HBatteryInfo"]]|(% style="width:62.5px" %)(((
228 -[[Temperature DS18B20>>||anchor="HDS18B20Temperaturesensor"]]
229 -)))|[[Distance>>||anchor="HDistance"]]|[[Distance signal strength>>||anchor="HDistancesignalstrength"]]|(% style="width:122px" %)(((
230 -[[Interrupt flag & Interrupt_level>>||anchor="HInterruptPin26A0InterruptLevel"]]
231 -)))|(% style="width:54px" %)[[LiDAR temp>>||anchor="HLiDARtemp"]]|(% style="width:96px" %)(((
232 -[[Message Type>>||anchor="HMessageType"]]
233 -)))
234 234  
235 -[[image:image-20230805104104-2.png||height="136" width="754"]]
278 +(% style="color:blue" %)**Probe Mechanical:**
236 236  
280 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615090910-1.png?rev=1.1||alt="image-20220615090910-1.png"]]
237 237  
238 -==== (% style="color:blue" %)**Battery Info**(%%) ====
239 239  
283 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615090910-2.png?rev=1.1||alt="image-20220615090910-2.png"]]
240 240  
241 -Check the battery voltage for DS20L.
242 242  
243 -Ex1: 0x0B45 = 2885mV
286 += 2. Configure LDS12-LB to connect to LoRaWAN network =
244 244  
245 -Ex2: 0x0B49 = 2889mV
288 +== 2.1 How it works ==
246 246  
247 247  
248 -==== (% style="color:blue" %)**DS18B20 Temperature sensor**(%%) ====
291 +The LDS12-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the LDS12-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
249 249  
293 +(% style="display:none" %) (%%)
250 250  
251 -This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
295 +== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
252 252  
253 253  
254 -**Example**:
298 +Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
255 255  
256 -If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
300 +The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
257 257  
258 -If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
302 +[[image:image-20230613140140-4.png||height="453" width="800"]](% style="display:none" %)
259 259  
260 260  
261 -==== (% style="color:blue" %)**Distance**(%%) ====
305 +(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from LDS12-LB.
262 262  
307 +Each LDS12-LB is shipped with a sticker with the default device EUI as below:
263 263  
264 -Represents the distance value of the measurement output, the default unit is cm, and the value range parsed as a decimal number is 0-1200. In actual use, when the signal strength value Strength.
309 +[[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
265 265  
266 266  
267 -**Example**:
312 +You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
268 268  
269 -If the data you get from the register is 0x0B 0xEA, the distance between the sensor and the measured object is 0BEA(H) = 3050 (D)/10 = 305cm.
270 270  
315 +(% style="color:blue" %)**Register the device**
271 271  
272 -==== (% style="color:blue" %)**Distance signal strength**(%%) ====
317 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]
273 273  
274 274  
275 -Refers to the signal strength, the default output value will be between 0-65535. When the distance measurement gear is fixed, the farther the distance measurement is, the lower the signal strength; the lower the target reflectivity, the lower the signal strength. When Strength is greater than 100 and not equal to 65535, the measured value of Dist is considered credible.
320 +(% style="color:blue" %)**Add APP EUI and DEV EUI**
276 276  
322 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]
277 277  
278 -**Example**:
279 279  
280 -If payload is: 01D7(H)=471(D), distance signal strength=471, 471>100,471≠65535, the measured value of Dist is considered credible.
325 +(% style="color:blue" %)**Add APP EUI in the application**
281 281  
282 -Customers can judge whether they need to adjust the environment based on the signal strength.
283 283  
328 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]
284 284  
285 -**1) When the sensor detects valid data:**
286 286  
287 -[[image:image-20230805155335-1.png||height="145" width="724"]]
331 +(% style="color:blue" %)**Add APP KEY**
288 288  
333 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
289 289  
290 -**2) When the sensor detects invalid data:**
291 291  
292 -[[image:image-20230805155428-2.png||height="139" width="726"]]
336 +(% style="color:blue" %)**Step 2:**(%%) Activate on LDS12-LB
293 293  
294 294  
295 -**3) When the sensor is not connected:**
339 +Press the button for 5 seconds to activate the LDS12-LB.
296 296  
297 -[[image:image-20230805155515-3.png||height="143" width="725"]]
341 +(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
298 298  
343 +After join success, it will start to upload messages to TTN and you can see the messages in the panel.
299 299  
300 -==== (% style="color:blue" %)**Interrupt Pin & Interrupt Level**(%%) ====
301 301  
346 +== 2.3  ​Uplink Payload ==
302 302  
303 -This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up.
304 304  
305 -Note: The Internet Pin is a separate pin in the screw terminal. See pin mapping of GPIO_EXTI .
306 -
307 -**Example:**
308 -
309 -If byte[0]&0x01=0x00 : Normal uplink packet.
310 -
311 -If byte[0]&0x01=0x01 : Interrupt Uplink Packet.
312 -
313 -
314 -==== (% style="color:blue" %)**LiDAR temp**(%%) ====
315 -
316 -
317 -Characterize the internal temperature value of the sensor.
318 -
319 -**Example: **
320 -If payload is: 1C(H) <<24>>24=28(D),LiDAR temp=28℃.
321 -If payload is: F2(H) <<24>>24=-14(D),LiDAR temp=-14℃.
322 -
323 -
324 -==== (% style="color:blue" %)**Message Type**(%%) ====
325 -
326 -
327 327  (((
328 -For a normal uplink payload, the message type is always 0x01.
350 +LDS12-LB will uplink payload via LoRaWAN with below payload format: 
329 329  )))
330 330  
331 331  (((
332 -Valid Message Type:
354 +Uplink payload includes in total 8 bytes.
333 333  )))
334 334  
335 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:499px" %)
336 -|=(% style="width: 161px;background-color:#4F81BD;color:white" %)**Message Type Code**|=(% style="width: 164px;background-color:#4F81BD;color:white" %)**Description**|=(% style="width: 174px;background-color:#4F81BD;color:white" %)**Payload**
337 -|(% style="width:160px" %)0x01|(% style="width:163px" %)Normal Uplink|(% style="width:173px" %)Normal Uplink Payload
338 -|(% style="width:160px" %)0x02|(% style="width:163px" %)Reply configures info|(% style="width:173px" %)Configure Info Payload
357 +(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
358 +|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)(((
359 +**Size(bytes)**
360 +)))|=(% style="width: 62.5px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="background-color:#D9E2F3;color:#0070C0" %)1|=(% style="background-color:#D9E2F3;color:#0070C0" %)2|=(% style="background-color:#D9E2F3;color:#0070C0" %)**1**
361 +|(% style="width:62.5px" %)Value|(% style="width:62.5px" %)[[BAT>>||anchor="H2.3.1A0BatteryInfo"]]|(((
362 +[[Distance>>||anchor="H2.3.2A0Distance"]]
363 +(unit: mm)
364 +)))|[[Digital Interrupt (Optional)>>||anchor="H2.3.3A0InterruptPin"]]|(((
365 +[[Temperature (Optional )>>||anchor="H2.3.4A0DS18B20Temperaturesensor"]]
366 +)))|[[Sensor Flag>>||anchor="H2.3.5A0SensorFlag"]]
339 339  
340 -[[image:image-20230805150315-4.png||height="233" width="723"]]
368 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/1654850511545-399.png?rev=1.1||alt="1654850511545-399.png"]]
341 341  
342 342  
343 -=== 2.3.3 Historical measuring distance, FPORT~=3 ===
371 +=== 2.3.1  Battery Info ===
344 344  
345 345  
346 -DS20L stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.5.4Pollsensorvalue"]].
374 +Check the battery voltage for LDS12-LB.
347 347  
348 -The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time measuring distance.
376 +Ex1: 0x0B45 = 2885mV
349 349  
350 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
351 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
352 -**Size(bytes)**
353 -)))|=(% style="width: 80px;background-color:#4F81BD;color:white" %)1|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 50px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 70px;background-color:#4F81BD;color:white" %)**2**|=(% style="background-color:#4F81BD; color: white; width: 85px;" %)**1**|=(% style="background-color: #4F81BD; color: white; width: 85px;" %)4
354 -|(% style="width:62.5px" %)Value|(% style="width:62.5px" %)Interrupt flag & Interrupt_level|(% style="width:62.5px" %)(((
355 -Reserve(0xFF)
356 -)))|Distance|Distance signal strength|(% style="width:88px" %)(((
357 -LiDAR temp
358 -)))|(% style="width:85px" %)Unix TimeStamp
378 +Ex2: 0x0B49 = 2889mV
359 359  
360 -**Interrupt flag & Interrupt level:**
361 361  
362 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:480px" %)
363 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
364 -**Size(bit)**
365 -)))|=(% style="width: 90px;background-color:#4F81BD;color:white" %)**bit7**|=(% style="width: 90px;background-color:#4F81BD;color:white" %)**bit6**|=(% style="width: 60px;background-color:#4F81BD;color:white" %)**[bit5:bit2]**|=(% style="width: 90px; background-color: #4F81BD; color: white;" %)**bit1**|=(% style="background-color: #4F81BD; color: white; width: 90px;" %)**bit0**
366 -|(% style="width:62.5px" %)Value|(% style="width:62.5px" %)No ACK message|(% style="width:62.5px" %)Poll Message Flag|Reserve|(% style="width:91px" %)Interrupt level|(% style="width:88px" %)(((
367 -Interrupt flag
368 -)))
381 +=== 2.3.2  Distance ===
369 369  
370 -* (((
371 -Each data entry is 11 bytes and has the same structure as [[Uplink Payload>>||anchor="H2.3.2UplinkPayload2CFPORT3D2"]], to save airtime and battery, DS20L will send max bytes according to the current DR and Frequency bands.
383 +
384 +(((
385 +Get the distance. Flat object range 20mm - 2000mm.
372 372  )))
373 373  
374 -For example, in the US915 band, the max payload for different DR is:
388 +(((
389 +For example, if the data you get from the register is **0x06 0x05**, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
375 375  
376 -**a) DR0:** max is 11 bytes so one entry of data
391 +(% style="color:blue" %)**0605(H) = 1541 (D) = 1541 mm.**
392 +)))
377 377  
378 -**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
394 +* If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
379 379  
380 -**c) DR2:** total payload includes 11 entries of data
396 +* If the sensor value lower than 0x0014 (20mm), the sensor value will be invalid.
381 381  
382 -**d) DR3:** total payload includes 22 entries of data.
383 383  
384 -If DS20L doesn't have any data in the polling time. It will uplink 11 bytes of 0
399 +=== 2.3.3  Interrupt Pin ===
385 385  
386 386  
387 -**Downlink:**
402 +This data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up.
388 388  
389 -0x31 64 CC 68 0C 64 CC 69 74 05
404 +**Example:**
390 390  
391 -[[image:image-20230805144936-2.png||height="113" width="746"]]
406 +0x00: Normal uplink packet.
392 392  
393 -**Uplink:**
408 +0x01: Interrupt Uplink Packet.
394 394  
395 -43 FF 0E 10 00 B0 1E 64 CC 68 0C 40 FF 0D DE 00 A8 1E 64 CC 68 29 40 FF 09 92 00 D3 1E 64 CC 68 65 40 FF 02 3A 02 BC 1E 64 CC 68 A1 41 FF 0E 1A 00 A4 1E 64 CC 68 C0 40 FF 0D 2A 00 B8 1E 64 CC 68 E8 40 FF 00 C8 11 6A 1E 64 CC 69 24 40 FF 0E 24 00 AD 1E 64 CC 69 6D
396 396  
411 +=== 2.3.4  DS18B20 Temperature sensor ===
397 397  
398 -**Parsed Value:**
399 399  
400 -[DISTANCE , DISTANCE_SIGNAL_STRENGTH，LIDAR_TEMP，EXTI_STATUS , EXTI_FLAG , TIME]
414 +This is optional, user can connect external DS18B20 sensor to the +3.3v, 1-wire and GND pin . and this field will report temperature.
401 401  
416 +**Example**:
402 402  
403 -[360,176,30,High,True,2023-08-04 02:53:00],
418 +If payload is: 0105H:  (0105 & FC00 == 0), temp = 0105H /10 = 26.1 degree
404 404  
405 -[355,168,30,Low,False,2023-08-04 02:53:29],
420 +If payload is: FF3FH :  (FF3F & FC00 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
406 406  
407 -[245,211,30,Low,False,2023-08-04 02:54:29],
408 408  
409 -[57,700,30,Low,False,2023-08-04 02:55:29],
423 +=== 2.3.5  Sensor Flag ===
410 410  
411 -[361,164,30,Low,True,2023-08-04 02:56:00],
412 412  
413 -[337,184,30,Low,False,2023-08-04 02:56:40],
426 +(((
427 +0x01: Detect Ultrasonic Sensor
428 +)))
414 414  
415 -[20,4458,30,Low,False,2023-08-04 02:57:40],
430 +(((
431 +0x00: No Ultrasonic Sensor
432 +)))
416 416  
417 -[362,173,30,Low,False,2023-08-04 02:58:53],
418 418  
435 +=== 2.3.6  Decode payload in The Things Network ===
419 419  
420 -**History read from serial port：**
421 421  
422 -[[image:image-20230805145056-3.png]]
423 -
424 -
425 -=== 2.3.4 Decode payload in The Things Network ===
426 -
427 -
428 428  While using TTN network, you can add the payload format to decode the payload.
429 429  
430 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLDS12-LoRaWAN%20LiDAR%20ToF%20Distance%20Sensor%20User%20Manual/WebHome/1654592762713-715.png?rev=1.1||alt="1654592762713-715.png"]]
440 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654850829385-439.png?rev=1.1||alt="1654850829385-439.png"]]
431 431  
442 +The payload decoder function for TTN V3 is here:
432 432  
433 433  (((
434 -The payload decoder function for TTN is here:
445 +LDS12-LB TTN V3 Payload Decoder:  [[ttps:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
435 435  )))
436 436  
437 -(((
438 -DS20L TTN Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
439 -)))
440 440  
449 +== 2.4  Uplink Interval ==
441 441  
442 -== 2.4 ​Show Data in DataCake IoT Server ==
443 443  
452 +The LDS12-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>||anchor="H3.3.1SetTransmitIntervalTime"]]
444 444  
454 +
455 +== 2.5  ​Show Data in DataCake IoT Server ==
456 +
457 +
445 445  (((
446 446  [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
447 447  )))
... ... @@ -464,7 +464,7 @@
464 464  
465 465  (% style="color:blue" %)**Step 3**(%%)**: Create an account or log in Datacake.**
466 466  
467 -(% style="color:blue" %)**Step 4**(%%)**: Search the DS20L and add DevEUI.**
480 +(% style="color:blue" %)**Step 4**(%%)**: Search the LDS12-LB and add DevEUI.**
468 468  
469 469  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654851029373-510.png?rev=1.1||alt="1654851029373-510.png"]]
470 470  
... ... @@ -474,29 +474,34 @@
474 474  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20220610165129-11.png?width=1088&height=595&rev=1.1||alt="image-20220610165129-11.png"]]
475 475  
476 476  
477 -== 2.5 Datalog Feature ==
490 +== 2.6 Datalog Feature ==
478 478  
479 479  
480 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DS20L will store the reading for future retrieving purposes.
493 +Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, LDS12-LB will store the reading for future retrieving purposes.
481 481  
482 482  
483 -=== 2.5.1 Ways to get datalog via LoRaWAN ===
496 +=== 2.6.1 Ways to get datalog via LoRaWAN ===
484 484  
485 485  
486 -Set PNACKMD=1, DS20L will wait for ACK for every uplink, when there is no LoRaWAN network, DS20L will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
499 +Set PNACKMD=1, LDS12-LB will wait for ACK for every uplink, when there is no LoRaWAN network,LDS12-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
487 487  
488 488  * (((
489 -a) DS20L will do an ACK check for data records sending to make sure every data arrive server.
502 +a) LDS12-LB will do an ACK check for data records sending to make sure every data arrive server.
490 490  )))
491 491  * (((
492 -b) DS20L will send data in **CONFIRMED Mode** when PNACKMD=1, but DS20L won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if DS20L gets a ACK, DS20L will consider there is a network connection and resend all NONE-ACK messages.
505 +b) LDS12-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but LDS12-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if LDS12-LB gets a ACK, LDS12-LB will consider there is a network connection and resend all NONE-ACK messages.
493 493  )))
494 494  
495 -=== 2.5.2 Unix TimeStamp ===
508 +Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
496 496  
510 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
497 497  
498 -DS20L uses Unix TimeStamp format based on
499 499  
513 +=== 2.6.2 Unix TimeStamp ===
514 +
515 +
516 +LDS12-LB uses Unix TimeStamp format based on
517 +
500 500  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
501 501  
502 502  User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
... ... @@ -509,23 +509,23 @@
509 509  So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
510 510  
511 511  
512 -=== 2.5.3 Set Device Time ===
530 +=== 2.6.3 Set Device Time ===
513 513  
514 514  
515 515  User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
516 516  
517 -Once DS20L Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to DS20L. If DS20L fails to get the time from the server, DS20L will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
535 +Once LDS12-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to LDS12-LB. If LDS12-LB fails to get the time from the server, LDS12-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
518 518  
519 519  (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
520 520  
521 521  
522 -=== 2.5.4 Poll sensor value ===
540 +=== 2.6.4 Poll sensor value ===
523 523  
524 524  
525 525  Users can poll sensor values based on timestamps. Below is the downlink command.
526 526  
527 527  (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:425.818px" %)
528 -|(% colspan="4" style="background-color:#4f81bd; color:white; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
546 +|(% colspan="4" style="background-color:#d9e2f3; color:#0070c0; width:423px" %)**Downlink Command to poll Open/Close status (0x31)**
529 529  |(% style="width:58px" %)**1byte**|(% style="width:127px" %)**4bytes**|(% style="width:124px" %)**4bytes**|(% style="width:114px" %)**1byte**
530 530  |(% style="width:58px" %)31|(% style="width:127px" %)Timestamp start|(% style="width:124px" %)Timestamp end|(% style="width:114px" %)Uplink Interval
531 531  
... ... @@ -542,24 +542,24 @@
542 542  )))
543 543  
544 544  (((
545 -Uplink Internal =5s，means DS20L will send one packet every 5s. range 5~~255s.
563 +Uplink Internal =5s，means LDS12-LB will send one packet every 5s. range 5~~255s.
546 546  )))
547 547  
548 548  
549 -== 2.6 Frequency Plans ==
567 +== 2.7 Frequency Plans ==
550 550  
551 551  
552 -The DS20L uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
570 +The LDS12-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
553 553  
554 554  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
555 555  
556 556  
557 -3. Configure DS20L
575 += 3. Configure LDS12-LB =
558 558  
559 559  == 3.1 Configure Methods ==
560 560  
561 561  
562 -DS20L supports below configure method:
580 +LDS12-LB supports below configure method:
563 563  
564 564  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
565 565  
... ... @@ -567,6 +567,7 @@
567 567  
568 568  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
569 569  
588 +
570 570  == 3.2 General Commands ==
571 571  
572 572  
... ... @@ -581,10 +581,10 @@
581 581  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
582 582  
583 583  
584 -== 3.3 Commands special design for DS20L ==
603 +== 3.3 Commands special design for LDS12-LB ==
585 585  
586 586  
587 -These commands only valid for DS20L, as below:
606 +These commands only valid for LDS12-LB, as below:
588 588  
589 589  
590 590  === 3.3.1 Set Transmit Interval Time ===
... ... @@ -599,7 +599,7 @@
599 599  )))
600 600  
601 601  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
602 -|=(% style="width: 156px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 137px;background-color:#4F81BD;color:white" %)**Function**|=(% style="background-color:#4F81BD;color:white" %)**Response**
621 +|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
603 603  |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
604 604  30000
605 605  OK
... ... @@ -635,24 +635,20 @@
635 635  === 3.3.2 Set Interrupt Mode ===
636 636  
637 637  
638 -Feature, Set Interrupt mode for pin of GPIO_EXTI.
657 +Feature, Set Interrupt mode for PA8 of pin.
639 639  
640 -When AT+INTMOD=0 is set, GPIO_EXTI is used as a digital input port.
659 +When AT+INTMOD=0 is set, PA8 is used as a digital input port.
641 641  
642 642  (% style="color:blue" %)**AT Command: AT+INTMOD**
643 643  
644 644  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
645 -|=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 197px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Response**
664 +|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
646 646  |(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
647 647  0
648 648  OK
649 649  the mode is 0 =Disable Interrupt
650 650  )))
651 -|(% style="width:154px" %)(((
652 -AT+INTMOD=2
653 -
654 -(default)
655 -)))|(% style="width:196px" %)(((
670 +|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
656 656  Set Transmit Interval
657 657  0. (Disable Interrupt),
658 658  ~1. (Trigger by rising and falling edge)
... ... @@ -670,10 +670,11 @@
670 670  
671 671  * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
672 672  
688 +
673 673  = 4. Battery & Power Consumption =
674 674  
675 675  
676 -DS20L use built-in 2400mAh non-chargeable battery for long-term use up to several years*. See below link for detail information about the battery info and how to replace.
692 +LDS12-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
677 677  
678 678  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
679 679  
... ... @@ -682,7 +682,7 @@
682 682  
683 683  
684 684  (% class="wikigeneratedid" %)
685 -User can change firmware DS20L to:
701 +User can change firmware LDS12-LB to:
686 686  
687 687  * Change Frequency band/ region.
688 688  
... ... @@ -690,7 +690,7 @@
690 690  
691 691  * Fix bugs.
692 692  
693 -Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/zqv1vt3komgp4tu/AAC33PnXIcWOVl_UXBEAeT_xa?dl=0]]**
709 +Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/ph4uyz0rchflrnw/AADr1f_5Sg30804NItpfOQbla?dl=0]]**
694 694  
695 695  Methods to Update Firmware:
696 696  
... ... @@ -698,12 +698,13 @@
698 698  
699 699  * Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
700 700  
717 +
701 701  = 6. FAQ =
702 702  
703 -== 6.1 What is the frequency plan for DS20L? ==
720 +== 6.1 What is the frequency plan for LDS12-LB? ==
704 704  
705 705  
706 -DS20L use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
723 +LDS12-LB use the same frequency as other Dragino products. User can see the detail from this link:  [[Introduction>>doc:Main.End Device Frequency Band.WebHome||anchor="H1.Introduction"]]
707 707  
708 708  
709 709  = 7. Trouble Shooting =
... ... @@ -718,11 +718,11 @@
718 718  
719 719  
720 720  (((
721 -(% style="color:blue" %)**Cause ①**(%%)**：**Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance. (such as glass and water, etc.)
738 +(% style="color:blue" %)**Cause ①**(%%)**：**Due to the physical principles of The LiDAR probe, the above phenomenon is likely to occur if the detection object is the material with high reflectivity (such as mirror, smooth floor tile, etc.) or transparent substance (such as glass and water, etc.)
722 722  )))
723 723  
724 724  (((
725 -(% style="color:red" %)**Troubleshooting**(%%): Please avoid use of this product under such circumstance in practice.
742 +Troubleshooting: Please avoid use of this product under such circumstance in practice.
726 726  )))
727 727  
728 728  
... ... @@ -731,7 +731,7 @@
731 731  )))
732 732  
733 733  (((
734 -(% style="color:red" %)**Troubleshooting**(%%): please use dry dust-free cloth to gently remove the foreign matter.
751 +Troubleshooting: please use dry dust-free cloth to gently remove the foreign matter.
735 735  )))
736 736  
737 737  
... ... @@ -738,7 +738,7 @@
738 738  = 8. Order Info =
739 739  
740 740  
741 -Part Number: (% style="color:blue" %)**DS20L-XXX**
758 +Part Number: (% style="color:blue" %)**LDS12-LB-XXX**
742 742  
743 743  (% style="color:red" %)**XXX**(%%): **The default frequency band**
744 744  
... ... @@ -758,12 +758,13 @@
758 758  
759 759  * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
760 760  
778 +
761 761  = 9. ​Packing Info =
762 762  
763 763  
764 764  (% style="color:#037691" %)**Package Includes**:
765 765  
766 -* DS20L LoRaWAN Smart Distance Detector x 1
784 +* LDS12-LB LoRaWAN LiDAR ToF Distance Sensor x 1
767 767  
768 768  (% style="color:#037691" %)**Dimension and weight**:
769 769  
... ... @@ -775,6 +775,7 @@
775 775  
776 776  * Weight / pcs : g
777 777  
796 +
778 778  = 10. Support =
779 779  
780 780  
image-20230615152941-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -87.9 KB
Content
image-20230615153004-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -87.9 KB
Content
image-20230805103904-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -46.9 KB
Content
image-20230805104104-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -46.3 KB
Content
image-20230805144259-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -872.7 KB
Content
image-20230805144936-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -37.5 KB
Content
image-20230805145056-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -30.7 KB
Content
image-20230805150315-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -90.6 KB
Content
image-20230805155335-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -45.4 KB
Content
image-20230805155428-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -45.5 KB
Content
image-20230805155515-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -45.7 KB
Content
image-20231110085300-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -613.3 KB
Content
image-20231110085342-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -178.7 KB
Content
image-20231110091447-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -85.4 KB
Content
image-20231110091506-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -85.4 KB
Content
image-20231110102635-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -84.7 KB
Content