DS03A-LB Outdoor LoRaWAN Door Sensor User Manual

The Dragino DS03A-LB is a (% style="color:blue" %)**LoRaWAN Door Sensor**(%%) for Internet of Things solution. It detects door open/close status and uplinks to IoT server via LoRaWAN network. user can see the door status, open duration, open counts in the IoT Server.

21

)))

22

23

(((

24

The LoRa wireless technology used in DS03A-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.

)))

(((

The DS03A-LB will send periodically data every 2 hours as well as for each door open/close action. It also counts the door open times and calculates the last door open duration. Users can also disable the uplink for each open/close event, instead, DS03A-LB can count each open event and uplink periodically.

)))

(((

DS03A-LB supports (% style="color:blue" %)**Datalog Feature,**(%%) it can save the data when there is no LoRaWAN network and uplink when network recover.

)))

(((

DS03A-LB has the (% style="color:blue" %)**Open Alarm Feature**(%%), user can set this feature so the device will send an alarm if the door has been open for a certain time.

37

38

DS03A-LB is designed for outdoor use. It has a weatherproof enclosure and industrial level battery to work in low to high temperatures

)))

(((

DS03A-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.

)))

(((

DS03A-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.

)))

(((

Each DS03A-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.

)))

[[image:image-20230522092934-2.png||height="346" width="774"]]

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

61

* Ultra-low power consumption

62

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

63

* Door Open/Close detect

64

* Door open/close statistics

65

* Datalog Feature, Open Alarm Feature

66

* Support Bluetooth v5.1 and LoRaWAN remote configure

67

* Support wireless OTA update firmware

68

* Uplink on periodically

69

* Downlink to change configure

70

* 8500mAh Battery for long term use

* Wall Mountable

* Outdoor Use

== 1.3 Specification ==

75

76

77

(% style="color:#037691" %)**Common DC Characteristics:**

78

79

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

80

* Operating Temperature: -40 ~~ 85°C

81

82

(% style="color:#037691" %)**Sensor Detect Distance:**

83

84

* Wood Door: 10mm ~~ 30mm

85

* Iron Door: 30 ~~ 45mm

86

87

(% style="color:#037691" %)**LoRa Spec:**

88

89

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

90

* Max +22 dBm constant RF output vs.

91

* RX sensitivity: down to -139 dBm.

92

* Excellent blocking immunity

93

94

(% style="color:#037691" %)**Battery:**

95

96

* Li/SOCI2 un-chargeable battery

97

* Capacity: 8500mAh

98

* Self-Discharge: <1% / Year @ 25°C

99

* Max continuously current: 130mA

100

* Max boost current: 2A, 1 second

101

102

(% style="color:#037691" %)**Power Consumption**

103

104

* Sleep Mode: 5uA @ 3.3v

105

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

106

107

== 1.4 Applications ==

108

109

110

[[image:Main.User Manual for LoRaWAN End Nodes.LDS03A - Outdoor LoRaWAN OpenClose Door Sensor Manual.WebHome@1654741400370-813.png]]

111

112

113

== 1.5 Sleep mode and working mode ==

114

115

116

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

117

118

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

119

120

121

== 1.6 Button & LEDs ==

122

123

124

[[image:Main.User Manual for LoRaWAN End Nodes.PS-LB -- LoRaWAN Pressure Sensor.WebHome@1675071855856-879.png]]

125

126

127

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

128

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

129

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

130

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

131

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

132

)))

133

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

134

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

135

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

136

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

137

)))

138

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means Device is in Deep Sleep Mode.

139

140

== 1.7 BLE connection ==

141

142

143

DS03A-LB support BLE remote configure.

144

145

146

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

147

148

* Press button to send an uplink

149

* Press button to active device.

150

* Device Power on or reset.

151

152

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

153

154

155

== 1.8 Pin Definitions ==

156

157

[[image:image-20230630160843-7.png]]

== 1.9 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.LDS03A - Outdoor LoRaWAN OpenClose Door Sensor Manual.WebHome@1654741444887-479.png||height="399" width="513"]]

163

164

165

[[image:Main.User Manual for LoRaWAN End Nodes.PS-LB -- LoRaWAN Pressure Sensor.WebHome@1675143884058-338.png]]

166

167

168

[[image:Main.User Manual for LoRaWAN End Nodes.PS-LB -- LoRaWAN Pressure Sensor.WebHome@1675143899218-599.png]]

169

170

171

[[image:Main.User Manual for LoRaWAN End Nodes.PS-LB -- LoRaWAN Pressure Sensor.WebHome@1675143909447-639.png]]

172

173

174

= 2. Configure DS03A-LB to connect to LoRaWAN network =

175

176

== 2.1 How it works ==

177

178

179

The DS03A-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DS03A-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 2 hours.

180

181

182

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

183

184

185

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example. (% style="display:none" %)

186

187

The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

188

189

[[image:image-20230522092858-1.png||height="391" width="874"]]

190

191

192

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DS03A-LB.

193

194

Each DS03A-LB is shipped with a sticker with the default device EUI as below:

195

196

[[image:image-20230426085205-1.png||height="238" width="512"]]

197

198

199

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

200

201

(% style="display:none" %) (%%)

202

203

(% style="color:blue" %)**Register the device**

204

205

206

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675144099263-405.png?rev=1.1||alt="1675144099263-405.png"]](% style="display:none" %)

207

208

209

(% style="color:blue" %)**Add APP EUI and DEV EUI**

210

211

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675144117571-832.png?rev=1.1||alt="1675144117571-832.png"]]

212

213

214

(% style="color:blue" %)**Add APP EUI in the application**

215

216

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675144143021-195.png?rev=1.1||alt="1675144143021-195.png"]]

217

218

219

(% style="color:blue" %)**Add APP KEY**

220

221

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675144157838-392.png?rev=1.1||alt="1675144157838-392.png"]]

222

223

224

(% style="color:blue" %)**Step 2:**(%%) Activate on DS03A-LB

225

226

227

Press the button for 5 seconds to activate the DS03A-LB.

228

229

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to Join LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

230

231

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

232

233

234

== 2.3 Uplink Payload ==

235

236

=== 2.3.1 Device Status, FPORT~=5 ===

237

238

239

Users can use the downlink command(**0x26 01**) to ask DS03A-LB to send device configure detail, include device configure status. DS03A-LB will uplink a payload via FPort=5 to server.

240

241

The Payload format is as below.

242

243

244

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

245

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

250

251

[[image:image-20230630155406-1.png||height="190" width="873"]]

252

253

254

(% style="color:#037691" %)**Sensor Model**(%%): For DS03A-LB, this value is 0x1B

255

256

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

257

258

(% style="color:#037691" %)**Frequency Band**:

0x01: EU868

0x02: US915

0x03: IN865

0x04: AU915

0x05: KZ865

0x06: RU864

0x07: AS923

0x08: AS923-1

0x09: AS923-2

0x0a: AS923-3

0x0b: CN470

0x0c: EU433

0x0d: KR920

0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

290

291

AU915 and US915:value 0x00 ~~ 0x08

292

293

CN470: value 0x0B ~~ 0x0C

294

295

Other Bands: Always 0x00

296

297

298

(% style="color:#037691" %)**Battery Info**:

299

300

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== (% style="color:inherit; font-family:inherit; font-size:23px" %)2.3.2 Sensor Configuration, FPORT~=4(%%) ===

308

309

310

DS03A-LB will only send this command after getting the downlink command (0x26 02) from the server.

311

312

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

313

|(% colspan="5" style="background-color:#d9e2f3; color:#0070c0; width:504px" %)**Sensor Configuration FPORT=4**

* (((

(% style="color:blue" %)**TDC: (default: 0x001C20)**

319

)))

320

321

Uplink interval for the Open/Close Event, default value is 0x001C20 which is 7200 seconds = 2 hours.

* (((

(% style="color:blue" %)**Disalarm: (default: 0)**

326

)))

327

328

**If Disalarm = 1**, DS03A-LB will only send uplink at every TDC periodically. This is normally use for pulse meter application, in this application, there are many open/close event, and platform only care about the total number of pulse.

329

330

**If Disalarm = 0**, DS03A-LB will send uplink at every TDC periodically and send data on each open/close event. This is useful for the application user need to monitor the open/close event in real-time.

331

332

333

(% style="color:red" %)** Note: When Disalarm=0, a high frequently open/close event will cause lots of uplink and drain battery very fast. **

* (((

(% style="color:blue" %)**Keep Status & Keep Time**

338

)))

339

340

Shows the configure value of [[Alarm Base on Timeout Feature>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H3.8A0AlarmBaseonTimeout]]

341

342

[[image:image-20230630155527-3.png||height="146" width="902"]]

343

344

345

=== 2.3.3 Real-Time Open/Close Status, Uplink FPORT~=2 ===

346

347

348

DS03A-LB will send this uplink **after** Device Status once join the LoRaWAN network successfully. And DS03A-LB will send uplinks when:

349

350

* Every 2 hours, this interval [[can be changed>>||anchor="H3.3.1SetTransmitIntervalTime"]].

351

* There is an Open/Close event. (This info can be disabled by AT+DISALARM=1)

352

353

Uplink Payload totals 11 bytes.

354

355

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)

356

|=(% colspan="5" style="background-color:#D9E2F3;color:#0070C0;width:515px" %)**Real-Time Open/Close Status, FPORT=2**

357

358

|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((

359

Status

360

361

&[[Alarm>>||anchor="H3.3.4A0AlarmBaseonTimeout"]]

362

)))|(% style="width:95px" %)Total open door events|(% style="width:119px" %)(((

363

The last door open duration (unit: sec)

364

)))|(% style="width:108px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]

**Status & Alarm:**

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:680px" %)

369

|(% style="background-color:#d9e2f3; color:#0070c0; width:59px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:79px" %)**[bit7:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:110px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:106px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:167px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:122px" %)**bit0**

370

|(% style="width:76px" %)**Value**|(% style="width:96px" %)Reserve|(% style="width:110px" %)(((

371

Count mod

372

)))|(% style="width:106px" %)TDC flag 0:No;1:Yes|(% style="width:167px" %)[[Enable/disable Timeout Alarm>>||anchor="H3.3.3A0Enable2FDisableAlarm"]]

373

0: No Alarm; 1: Alarm|(% style="width:122px" %)Status 0: Close, 1: Open

374

375

[[image:image-20230630155451-2.png||height="246" width="928"]]

376

377

[[image:image-20230630155908-6.png||height="295" width="927"]]

378

379

380

=== 2.3.4 Historical Door Open/Close Event, FPORT~=3 ===

381

382

383

DS03A-LB stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.5DatalogFeature"]].

384

385

The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time open/close status.

386

387

* (((

388

Each data entry is 11 bytes and has the same structure as [[Real-Time open/close status>>||anchor="H2.3.2A0Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]], to save airtime and battery, DS03A-LB will send max bytes according to the current DR and Frequency bands.

389

)))

390

391

For example, in the US915 band, the max payload for different DR is:

392

393

(((

394

**~1. DR0**: max is 11 bytes so one entry of data

)))

(((

**2. DR1**: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)

)))

(((

**3. DR2**: total payload includes 11 entries of data

)))

(((

**4. DR3**: total payload includes 22 entries of data.

407

)))

408

409

If DS03A-LB doesn't have any data in the polling time. It will uplink 11 bytes of 0

410

411

[[image:image-20230630155556-4.png||height="146" width="938"]]

**Downlink:**

0x31 64 9E 7D 34 64 9E 7E 9C 05

**Uplink:**

45 00 00 00 00 00 00 64 9E 7D 48 40 00 00 00 00 00 63 64 9E 7D 9C 41 00 00 01 00 00 63 64 9E 7D A4 40 00 00 01 00 00 8D 64 9E 7E 31 43 00 00 02 00 00 8D 64 9E 7E 44 48 00 00 02 00 00 1F 64 9E 7E 59 4B 00 00 03 00 00 1F 64 9E 7E 6B

**Parsed Value:**

[COUNTMOD, TDC_FLAG, ALARM, DOOR_STATUS, DOOR_OPEN_TIMES, LAST_DOOR_OPEN_DURATION, TIME]

426

427

428

[SUM,YES,FALSE,OPEN,0,0,2023-06-30 06:59:20],

429

430

[SUM,NO,FALSE,CLOSE,0,99,2023-06-30 07:00:44],

431

432

[SUM,NO,FALSE,OPEN, 1,99,2023-06-30 07:00:52],

433

434

[SUM,NO,FALSE,CLOSE,1,141,2023-06-30 07:03:13],

435

436

[SUM,NO,TRUE,OPEN, 2,141,2023-06-30 07:03:32],

437

438

[PART,NO,FALSE,CLOSE,2,31,2023-06-30 07:03:53],

439

440

[PART,NO,TRUE,OPEN, 3,31,2023-06-30 07:04:11],

441

442

[[image:image-20230630155751-5.png||height="188" width="809"]]

443

444

445

== 2.4 Payload Decoder file ==

(((

In TTN, use can add a custom payload so it shows friendly.

)))

(((

In the page **Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder** to add the decoder from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]

)))

== 2.5 Datalog Feature ==

458

459

460

(% style="color:blue" %)**Datalog Feature** (%%)is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DS03A-LB will store the reading for future retrieving purposes.

461

462

463

=== 2.5.1 Ways to get datalog via LoRaWAN ===

464

465

466

Set PNACKMD=1, DS03A-LB will wait for ACK for every uplink, when there is no LoRaWAN network,DS03A-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.

467

468

* a) DS03A-LB will do an ACK check for data records sending to make sure every data arrive server.

469

* b) DS03A-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but DS03A-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if DS03A-LB gets a ACK, DS03A-LB will consider there is a network connection and resend all NONE-ACK Message.

470

471

Below is the typical case for the Datalog Feature (Set PNACKMD=1)

472

473

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="image-20220703111700-2.png" height="381" width="1119"]]

474

475

476

=== 2.5.2 Unix TimeStamp ===

477

478

479

DS03A-LB uses Unix TimeStamp format based on

480

481

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="image-20220523001219-11.png" height="97" width="627"]]

482

483

User can get this time from link: [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :

484

485

Below is the converter example

486

487

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="image-20220523001219-12.png" height="298" width="720"]]

488

489

So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25

490

491

492

=== 2.5.3 Set Device Time ===

493

494

495

User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.

496

497

Once DS03A-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to DS03A-LB. If DS03A-LB fails to get the time from the server, DS03A-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).

498

499

(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN v3 and loriot support but TTN v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN v2 if SYNCMOD=1.**

500

501

502

== 2.6 Show Data in DataCake IoT Server ==

503

504

505

Datacake IoT platform provides a human-friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:

506

507

508

(% style="color:blue" %)**Step 1:**(%%)** Link TTNv3 to Datacake.**[[https:~~/~~/docs.datacake.de/lorawan/lns/thethingsindustries#create-integration-on-tti>>url:https://docs.datacake.de/lorawan/lns/thethingsindustries#create-integration-on-tti]]

509

510

(% style="color:blue" %)**Step 2:**(%%)** Configure DS03A-LB in Datacake.**

511

512

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746350207-427.png?rev=1.1||alt="1654746350207-427.png"]]

513

514

515

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654747162439-840.png?rev=1.1||alt="1654747162439-840.png"]]

516

517

518

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746405400-203.png?rev=1.1||alt="1654746405400-203.png"]]

519

520

521

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746763908-732.png?rev=1.1||alt="1654746763908-732.png"]]

522

523

524

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746716087-684.png?rev=1.1||alt="1654746716087-684.png"]]

525

526

527

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746693868-718.png?rev=1.1||alt="1654746693868-718.png"]]

528

529

530

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746674738-826.png?rev=1.1||alt="1654746674738-826.png"]]

531

532

533

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746646379-591.png?rev=1.1||alt="1654746646379-591.png"]]

534

535

536

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746549277-209.png?rev=1.1||alt="1654746549277-209.png"]]

537

538

539

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746593411-887.png?rev=1.1||alt="1654746593411-887.png"]]

540

541

542

== 2.7 Frequency Plans ==

543

544

545

The DS03A-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

546

547

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

548

549

550

== 2.8 Firmware Change Log ==

551

552

553

**Firmware download link: **[[https:~~/~~/www.dropbox.com/sh/b0uwyzjs4px4eao/AADvI7fPRwsFKTglEmaRRuaaa?dl=0>>https://www.dropbox.com/sh/b0uwyzjs4px4eao/AADvI7fPRwsFKTglEmaRRuaaa?dl=0]]

554

555

556

= 3. Configure DS03A-LB =

557

558

== 3.1 Configure Methods: ==

559

560

561

DS03A-LB supports below configure method:

562

563

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

564

* AT Command via UART Connection : See [[Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

565

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

566

567

== 3.2 General Commands ==

568

569

570

These commands are to configure:

571

572

* General system settings like: uplink interval.

573

* LoRaWAN protocol & radio related command.

574

575

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

576

577

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

578

579

580

== 3.3 Commands special design for DS03A-LB ==

581

582

583

These commands only valid for DS03A-LB, as below:

584

585

586

=== 3.3.1 Set Transmit Interval Time ===

587

588

589

Feature: Change LoRaWAN End Node Transmit Interval.

590

591

(% style="color:blue" %)**AT Command: AT+TDC**

592

593

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

594

|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**

595

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

596

30000

597

OK

598

the interval is 30000ms = 30s

599

)))

600

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

601

OK

602

Set transmit interval to 60000ms = 60 seconds

603

)))

604

605

(% style="color:blue" %)**Downlink Command: 0x01**

606

607

Format: Command Code (0x01) followed by 3 bytes time value.

608

609

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

610

611

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

612

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

613

614

=== 3.3.2 Get Device Status ===

615

616

617

Send a LoRaWAN downlink to ask device send Alarm settings.

618

619

* (% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

620

621

Sensor will upload Device Status via FPORT=5. See payload section for detail.

622

623

624

=== 3.3.3 Enable / Disable Alarm ===

625

626

627

Feature: Enable/Disable Alarm for open/close event. Default value 0.

628

629

(% style="color:blue" %)**AT Command: **

630

631

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)

632

|(% style="background-color:#d9e2f3; color:#0070c0; width:154px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:278px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0; width:88px" %)**Response**

633

|(% style="width:154px" %)AT+DISALARM=1|(% style="width:278px" %)End node will only send packets in TDC time.|OK

634

|(% style="width:154px" %)AT+DISALARM=0|(% style="width:278px" %)End node will send packets in TDC time or status change for door sensor|OK

635

636

(% style="color:blue" %)**Downlink Command: **

637

638

0xA7 01 ~/~/ Same As AT+DISALARM=1

639

640

0xA7 00 ~/~/ Same As AT+DISALARM=0

641

642

643

=== 3.3.4 Alarm Base on Timeout ===

644

645

646

DS03A-LB can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:

* (((

(% style="color:blue" %)**Keep Status: Status to be monitor**

651

)))

652

653

(% style="color:#037691" %)**Keep Status = 1**(%%): Monitor Close to Open event

654

655

(% style="color:#037691" %)**Keep Status = 0**(%%): Monitor Open to Close event

* (((

(% style="color:blue" %)**Keep Time: Timeout to send an Alarm**

660

)))

661

662

Range 0 ~~ 65535(0xFFFF) seconds.

663

664

If (% style="color:#037691" %)**keep time = 0**(%%), Disable Alarm Base on Timeout feature.

665

666

If (% style="color:#037691" %)**keep time > 0**(%%), device will monitor the keep status event and send an alarm when status doesn't change after timeout.

667

668

669

(% style="color:blue" %)**AT Command to configure:**

670

671

* (((

672

(% style="color:#037691" %)**AT+TTRIG=1,30** (%%) **~-~->** When the **Keep Status** change from close to open, and device remains in open status for more than 30 seconds. LDS03A will send an uplink packet, the [[Alarm bit>>||anchor="H2.3.2A0Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.

)))

* (((

(% style="color:#037691" %)**AT+TTRIG=0,0** (%%) **~-~-> ** Default Value, disable timeout Alarm.

677

)))

678

679

(% style="color:blue" %)**Downlink Command to configure:**

680

681

(% style="color:#037691" %)**Command: 0xA9 aa bb cc**

682

683

**A9:** Command Type Code

684

685

**aa:** status to be monitored

**bb cc:** timeout.

If user send 0xA9 01 00 1E: equal to AT+TTRIG=1,30

Or

0xA9 00 00 00: Equal to AT+TTRIG=0,0. Disable timeout Alarm.

695

696

697

=== 3.3.5 Count Mod ===

698

699

700

(% style="color:blue" %)**AT Command:**

701

702

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)

703

|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 277px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 88px;background-color:#D9E2F3;color:#0070C0" %)**Response**

704

|(% style="width:155px" %)(((

705

AT+COUNTMOD=0

706

)))|(% style="width:277px" %)(((

707

the count value keeps accumulating mode

708

)))|(% style="width:86px" %)(((

709

OK

710

)))

711

|(% style="width:155px" %)(((

712

AT+COUNTMOD=1

713

)))|(% style="width:277px" %)(((

714

the count value will be reset after each TDC time（Last Close Duration Reset after each uplink）

715

)))|(% style="width:86px" %)(((

OK

)))

(% style="color:blue" %)**Downlink Command:**

720

721

Example: 0B aa => AT+COUNTMOD = second byte

722

723

724

=== 3.3.6 Interrupt Pin Channel Mod ===

725

726

727

(% style="color:blue" %)**AT Command:**

728

729

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)

730

|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 288px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 57px;background-color:#D9E2F3;color:#0070C0" %)**Response**

731

|(% style="width:155px" %)(((

732

AT+TTRCHANNEL=1

733

)))|(% style="width:288px" %)(((

734

set as single channel, only use PA8 pin as interrupt pin.

735

)))|(% style="width:44px" %)(((

736

OK

737

)))

738

|(% style="width:155px" %)(((

739

AT+TTRCHANNEL=2

740

)))|(% style="width:288px" %)(((

741

is set as dual channel, use PA8 pin and PA4 pin as interrupt pin.

742

)))|(% style="width:44px" %)(((

OK

)))

(% style="color:blue" %)**Downlink Command:**

747

748

Example: 0D aa => AT+TTRCHANNEL = second byte

749

750

751

=== 3.3.7 Change the name of AT+TTRIG to AT+TTRIG1 ===

752

753

754

(% style="color:blue" %)**Downlink Command:**

755

756

Example: A9 01 aa bb cc => AT+TTRIG1= third byte, 4th byte and 5th byte

757

758

759

=== 3.3.8 Added AT+TTRIG2 for PB15 pin ===

760

761

762

(% style="color:blue" %)**Downlink Command:**

763

764

Example: A9 02 aa bb cc => AT+TTRIG2= third byte, 4th byte and 5th byte

765

766

767

=== 3.3.9 TTRIG1/2 timeout status alarm ===

768

769

770

It needs to be used with AT+TTRIG1 or AT+TTRIG2. When TTRIG1 or TTRIG2 times out and causes an alarm, and the status does not change subsequently, an alarm packet will be sent at the alarm interval.

771

772

(% style="color:blue" %)**AT Command:**

773

774

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

775

|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 279px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 76px;background-color:#D9E2F3;color:#0070C0" %)**Response**

776

|(% style="width:155px" %)(((

777

AT+TTRALARM=0

778

)))|(% style="width:279px" %)(((

779

disable continuous alarm

780

)))|(% style="width:84px" %)(((

781

OK

782

)))

783

|(% style="width:155px" %)(((

784

AT+TTRALARM=60

785

)))|(% style="width:279px" %)(((

786

The alarm interval is 60 minutes (unit: minutes)

787

)))|(% style="width:84px" %)(((

OK

)))

(% style="color:blue" %)**Downlink Command:**

792

793

Example: 0C aa => AT+TTRALARM= aa

794

795

796

= 4. Battery & Power Consumption =

797

798

799

DS03A-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

800

801

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

802

803

804

= 5. OTA firmware update =

805

806

807

User can change firmware DS03A-LB to:

808

809

* Change Frequency band/ region.

810

* Update with new features.

811

* Fix bugs.

812

813

Firmware and changelog can be downloaded from : **[[Firmware download link>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**

814

815

816

**Methods to Update Firmware:**

817

818

* (Recommanded way) OTA firmware update via wireless:** [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**

819

* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

= 7. Order Info =

Part Number: (% style="color:blue" %)**DS03A-LB-XX**

829

830

(% style="color:red" %)**XX**(%%): The default frequency band

831

832

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

833

834

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

835

836

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

837

838

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

839

840

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

841

842

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

843

844

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

845

846

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

= 8. Packing Info =

(% style="color:#037691" %)**Package Includes**:

852

853

* DS03A-LB LoRaWAN Temperature Sensor

854

855

(% style="color:#037691" %)**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

869

870

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].

Wiki source code of DS03A-LB Outdoor LoRaWAN Door Sensor User Manual

Applications

Navigation