Skip to Content
Last modified by Mengting Qiu on 2025/07/03 16:36
From version 31.1
edited by Saxer Lin
on 2023/07/01 09:43
Change comment: There is no comment for this version
To version 4.5
edited by Xiaoling
on 2023/05/16 09:21
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Saxer
1 +XWiki.Xiaoling
Content
... ... @@ -51,12 +51,8 @@
51 51  )))
52 52  
53 53  
54 -[[image:image-20230522092934-2.png||height="346" width="774"]]
55 -
56 -
57 57  == 1.2 ​Features ==
58 58  
59 -
60 60  * LoRaWAN 1.0.3 Class A
61 61  * Ultra-low power consumption
62 62  * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
... ... @@ -73,7 +73,6 @@
73 73  
74 74  == 1.3 Specification ==
75 75  
76 -
77 77  (% style="color:#037691" %)**Common DC Characteristics:**
78 78  
79 79  * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
... ... @@ -106,7 +106,6 @@
106 106  
107 107  == 1.4 Applications ==
108 108  
109 -
110 110  [[image:Main.User Manual for LoRaWAN End Nodes.LDS03A - Outdoor LoRaWAN OpenClose Door Sensor Manual.WebHome@1654741400370-813.png]]
111 111  
112 112  
... ... @@ -140,7 +140,7 @@
140 140  == 1.7 BLE connection ==
141 141  
142 142  
143 -DS03A-LB support BLE remote configure.
137 +D2x-LB support BLE remote configure.
144 144  
145 145  
146 146  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
... ... @@ -152,13 +152,9 @@
152 152  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
153 153  
154 154  
155 -== 1.8 Pin Definitions ==
149 +== 1.8 Mechanical ==
156 156  
157 -[[image:image-20230630160843-7.png]]
158 158  
159 -== 1.9 Mechanical ==
160 -
161 -
162 162  [[image:Main.User Manual for LoRaWAN End Nodes.LDS03A - Outdoor LoRaWAN OpenClose Door Sensor Manual.WebHome@1654741444887-479.png||height="399" width="513"]]
163 163  
164 164  
... ... @@ -176,7 +176,7 @@
176 176  == 2.1 How it works ==
177 177  
178 178  
179 -The DS03A-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DS03A-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 2 hours.
169 +The DS03A-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the DS03A-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
180 180  
181 181  
182 182  == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
... ... @@ -184,11 +184,9 @@
184 184  
185 185  Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example. (% style="display:none" %)
186 186  
187 -The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
177 +The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
188 188  
189 -[[image:image-20230522092858-1.png||height="391" width="874"]]
190 190  
191 -
192 192  (% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from DS03A-LB.
193 193  
194 194  Each DS03A-LB is shipped with a sticker with the default device EUI as below:
... ... @@ -235,7 +235,6 @@
235 235  
236 236  === 2.3.1 Device Status, FPORT~=5 ===
237 237  
238 -
239 239  Users can use the downlink command(**0x26 01**) to ask DS03A-LB to send device configure detail, include device configure status. DS03A-LB will uplink a payload via FPort=5 to server.
240 240  
241 241  The Payload format is as below.
... ... @@ -248,42 +248,42 @@
248 248  
249 249  Example parse in TTNv3
250 250  
251 -[[image:image-20230630155406-1.png||height="190" width="873"]]
238 +[[image:image-20230415153147-2.png||height="220" width="1120"]]
252 252  
253 253  
254 -(% style="color:#037691" %)**Sensor Model**(%%): For DS03A-LB, this value is 0x1B
241 +(% style="color:#037691" %)**Sensor Model**(%%): For DS03A-LB, this value is 0x0B
255 255  
256 256  (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
257 257  
258 258  (% style="color:#037691" %)**Frequency Band**:
259 259  
260 -0x01: EU868
247 +*0x01: EU868
261 261  
262 -0x02: US915
249 +*0x02: US915
263 263  
264 -0x03: IN865
251 +*0x03: IN865
265 265  
266 -0x04: AU915
253 +*0x04: AU915
267 267  
268 -0x05: KZ865
255 +*0x05: KZ865
269 269  
270 -0x06: RU864
257 +*0x06: RU864
271 271  
272 -0x07: AS923
259 +*0x07: AS923
273 273  
274 -0x08: AS923-1
261 +*0x08: AS923-1
275 275  
276 -0x09: AS923-2
263 +*0x09: AS923-2
277 277  
278 -0x0a: AS923-3
265 +*0x0a: AS923-3
279 279  
280 -0x0b: CN470
267 +*0x0b: CN470
281 281  
282 -0x0c: EU433
269 +*0x0c: EU433
283 283  
284 -0x0d: KR920
271 +*0x0d: KR920
285 285  
286 -0x0e: MA869
273 +*0x0e: MA869
287 287  
288 288  
289 289  (% style="color:#037691" %)**Sub-Band**:
... ... @@ -304,299 +304,140 @@
304 304  Ex2: 0x0B49 = 2889mV
305 305  
306 306  
307 -=== (% style="color:inherit; font-family:inherit; font-size:23px" %)2.3.2  Sensor Configuration, FPORT~=4(%%) ===
294 +=== 2.3.2  Real-Time Open/Close Status, Uplink FPORT~=2 ===
308 308  
309 309  
310 -DS03A-LB will only send this command after getting the downlink command (0x26 02) from the server.
311 -
312 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:723px" %)
313 -|(% colspan="8" style="background-color:#d9e2f3; color:#0070c0; width:721px" %)**Sensor Configuration FPORT=4**
314 -|**Size(bytes)**|(% style="width:75px" %)**3**|(% style="width:77px" %)**1**|(% style="width:96px" %)**1**|(% style="width:99px" %)**2**|(% style="width:87px" %)**1**|(% style="width:97px" %)**2**|(% style="width:98px" %)**1**
315 -|**Value**|(% style="width:75px" %)TDC (unit:sec)|(% style="width:77px" %)Disalarm|(% style="width:96px" %)(((
316 -Keep status1
317 -
318 -
319 -)))|(% style="width:99px" %)(((
320 -Keep time1
321 -
322 -(unit: sec)
323 -)))|(% style="width:87px" %)Keep status2|(% style="width:97px" %)(((
324 -Keep time2
325 -
326 -(unit: sec)
327 -)))|(% style="width:98px" %)(((
328 -Alarm interval
329 -
330 -(unit: min)
331 -)))
332 -
333 -* (((
334 -(% style="color:blue" %)**TDC: (default: 0x001C20)**
335 -)))
336 -
337 -Uplink interval for the Open/Close Event, default value is 0x001C20 which is 7200 seconds = 2 hours.
338 -
339 -
340 -* (((
341 -(% style="color:blue" %)**Disalarm: (default: 0)**
342 -)))
343 -
344 - **If Disalarm = 1**, DS03A-LB will only send uplink at every TDC periodically. This is normally use for pulse meter application, in this application, there are many open/close event, and platform only care about the total number of pulse.
345 -
346 - **If Disalarm = 0**, DS03A-LB will send uplink at every TDC periodically and send data on each open/close event. This is useful for the application user need to monitor the open/close event in real-time.
347 -
348 -
349 -(% style="color:red" %)** Note: When Disalarm=0, a high frequently open/close event will cause lots of uplink and drain battery very fast. **
350 -
351 -
352 -* (((
353 -(% style="color:blue" %)**Keep Status1 & Keep Time1 & Keep Status2 & Keep Time2**
354 -)))
355 -
356 -Shows the configure value of [[Alarm Base on Timeout Feature>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H3.8A0AlarmBaseonTimeout]]
357 -
358 -[[image:image-20230630155527-3.png||height="146" width="902"]]
359 -
360 -
361 -* (((
362 -(% style="color:blue" %)**Alarm interval(default: 0)**
363 -)))
364 -
365 -When the state of the door sensor has not been changed after the timeout alarm, the device will send a uplink every alarm interval. It will stop the alarm until the state of the door sensor is changed after the timeout alarm.
366 -
367 -
368 -=== 2.3.3  Real-Time Open/Close Status, Uplink FPORT~=2 ===
369 -
370 -
371 371  DS03A-LB will send this uplink **after** Device Status once join the LoRaWAN network successfully. And DS03A-LB will send uplinks when:
372 372  
373 -* Every 2 hours, this interval [[can be changed>>||anchor="H3.3.1SetTransmitIntervalTime"]].
299 +* Every 2 hours, this interval [[can be changed>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H3.1A0SetTransmitIntervalTime]].
374 374  * There is an Open/Close event.  (This info can be disabled by AT+DISALARM=1)
375 375  
376 -1)When **AT+TTRCHANNEL=1**, Uplink Payload totals 11 bytes. (**Default mode**)
302 +Uplink Payload totals 11 bytes.
377 377  
378 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
379 -|=(% colspan="5" style="background-color:#D9E2F3;color:#0070C0;width:515px" %)**Real-Time Open/Close Status, FPORT=2**
380 -|(% style="width:94px" %)**Size(bytes)**|(% style="width:97px" %)**1**|(% style="width:95px" %)**3**|(% style="width:119px" %)**3**|(% style="width:107px" %)**4**
381 -|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
382 -Status
304 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
305 +|=(% colspan="5" style="background-color: rgb(217, 226, 243); color: rgb(0, 112, 192); width: 522px;" %)**Real-Time Open/Close Status, FPORT=2**
306 +|(% style="width:95px" %)**Size(bytes)**|(% style="width:78px" %)**1**|(% style="width:98px" %)**3**|(% style="width:144px" %)**3**|(% style="width:108px" %)**4**
307 +|(% style="width:95px" %)**Value**|(% style="width:78px" %)Status & [[Alarm>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H3.8A0AlarmBaseonTimeout]]|(% style="width:98px" %)Total open door events|(% style="width:144px" %)(((
308 +The last door open duration (unit: min)
309 +)))|(% style="width:108px" %)[[Unix TimeStamp>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H2.4.1A0UnixTimeStamp]]
383 383  
384 -&[[Alarm>>||anchor="H3.3.4A0AlarmBaseonTimeout"]]
385 -)))|(% style="width:95px" %)Total open door events|(% style="width:119px" %)(((
386 -The last door open duration (unit: sec)
387 -)))|(% style="width:108px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
311 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:518.818px" %)
312 +|=(% colspan="4" style="background-color: rgb(217, 226, 243); color: rgb(0, 112, 192); width: 516px;" %)**Status & Alarm field**
313 +|(% style="width:76px" %)**Size(bit)**|(% style="width:70px" %)**6**|(% style="width:240px" %)**1**|(% style="width:130px" %)**1**
314 +|(% style="width:76px" %)**Value**|(% style="width:70px" %)Reserve|(% style="width:240px" %)[[Enable/disable Timeout Alarm>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H3.8A0AlarmBaseonTimeout]]
315 +0: No Alarm; 1: Alarm|(% style="width:130px" %)Status
316 +0: Close, 1: Open
388 388  
389 -**Status & Alarm:**
318 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/image-20220609110547-6.png?width=1191&height=337&rev=1.1||alt="image-20220609110547-6.png" height="337" width="1191"]]
390 390  
391 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:645px" %)
392 -|(% style="background-color:#d9e2f3; color:#0070c0; width:59px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:79px" %)**[bit7:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:110px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:106px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:125px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:129px" %)**bit0**
393 -|(% style="width:76px" %)**Value**|(% style="width:96px" %)Reserve|(% style="width:110px" %)(((
394 -Count mod
395 -)))|(% style="width:106px" %)TDC flag 0:No;1:Yes|(% style="width:125px" %)(((
396 -0: No Alarm;
397 397  
398 -1: Alarm
399 -)))|(% style="width:129px" %)(((
400 -Status 0: Close;
321 +=== 2.3.3  Historical Door Open/Close Event, FPORT~=3 ===
401 401  
402 -1: Open
403 -)))
404 404  
405 -[[image:image-20230630155451-2.png||height="246" width="928"]]
324 +DS03A-LB stores sensor values and users can retrieve these history values via the [[downlink command>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H2.4A0DatalogFeature]].
406 406  
326 +The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time open/close status.
407 407  
408 408  * (((
409 -(% style="color:blue" %)**Count mod:Default=0**
329 +Each data entry is 11 bytes and has the same structure as [[Real-Time open/close status>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H2.3.3A0Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2]], to save airtime and battery, DS03A-LB will send max bytes according to the current DR and Frequency bands.
410 410  )))
411 411  
412 -MOD=0 ~-~-> Uplink total door open times since factory
332 +For example, in the US915 band, the max payload for different DR is:
413 413  
414 -MOD=1 ~-~-> Uplink total door open times since last FPORT=2 uplink.
415 -
416 -
417 -* (% style="color:blue" %)**TDC flag**
418 -
419 -When the flag is 1, it means sending packets at normal time intervals.
420 -
421 -Otherwise, it is a packet sent at non-TDC time.
422 -
423 -
424 -* (((
425 -(% style="color:#0000ff" %)**Alarm**
334 +1. (((
335 +**DR0**: max is 11 bytes so one entry of data
426 426  )))
427 -
428 -See [[Alarm Base on Timeout>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H3.5AlarmBaseonTimeout]]
429 -
430 -
431 -* (((
432 -(% style="color:blue" %)**Status**
337 +1. (((
338 +**DR1**: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
433 433  )))
434 -
435 -This bit is 1 when the door sensor is open and 0 when it is close.
436 -
437 -
438 -* (((
439 -(% style="color:blue" %)**Total open door events**
340 +1. (((
341 +**DR2**: total payload includes 11 entries of data
440 440  )))
441 -
442 -Total pulse/counting base on open door.
443 -
444 -Range (3 Bytes) : 0x000000 ~~ 0xFFFFFF . Max: 16777215
445 -
446 -
447 -* (((
448 -(% style="color:blue" %)**The last door open duration**
343 +1. (((
344 +**DR3**: total payload includes 22 entries of data.
449 449  )))
450 450  
451 -Door sensor last open duration.
347 +If DS03A-LB doesn't have any data in the polling time. It will uplink 11 bytes of 0
452 452  
453 -Unit: sec.
349 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/image-20220609112215-7.png?width=1250&height=277&rev=1.1||alt="image-20220609112215-7.png" height="277" width="1250"]]
454 454  
455 -[[image:image-20230701094042-1.png||height="154" width="763"]]
351 +**Downlink:**
456 456  
353 +0x31 61 8E 57 40 61 8E 81 70 05
457 457  
458 -2)When **AT+TTRCHANNEL=2**, Uplink Payload totals 18 bytes.
459 459  
460 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:819px" %)
461 -|=(% colspan="8" style="background-color: rgb(217, 226, 243); color: rgb(0, 112, 192); width: 817px;" %)**Real-Time Open/Close Status, FPORT=2**
462 -|(% style="width:94px" %)**Size(bytes)**|(% style="width:97px" %)**1**|(% style="width:95px" %)**3**|(% style="width:125px" %)**3**|(% style="width:100px" %)**4**|(% style="width:86px" %)**1**|(% style="width:96px" %)**3**|(% style="width:126px" %)**3**
463 -|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
464 -Status1
356 +**Uplink:**
465 465  
466 -&[[Alarm>>||anchor="H3.3.4A0AlarmBaseonTimeout"]]1
467 -)))|(% style="width:95px" %)Total open door events1|(% style="width:125px" %)(((
468 -The last door open duration1 (unit: sec)
469 -)))|(% style="width:100px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]|(% style="width:86px" %)(((
470 -Status2
358 +00 00 00 00 00 00 00 61 8E 5F 8F 01 00 00 01 00 00 00 61 8E 5F D2 00 00 00 01 00 00 02 61 8E 60 64 01 00 00 02 00 00 02 61 8E 60 75 00 00 00 02 00 00 01 61 8E 60 C6 00 00 00 02 00 00 01 61 8E 7B A7 01 00 00 03 00 00 01 61 8E 7F 38 00 00 00 03 00 00 02 61 8E 7F CE 01 00 00 04 00 00 02 61 8E 81 1B 00 00 00 04 00 00 00 61 8E 81 50
471 471  
472 -&[[Alarm>>||anchor="H3.3.4A0AlarmBaseonTimeout"]]2
473 -)))|(% style="width:96px" %)Total open door events2|(% style="width:126px" %)The last door open duration2 (unit: sec)
474 474  
475 -**Status1 & Alarm1:**
361 +**Parsed Value:**
476 476  
477 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:730px" %)
478 -|(% style="background-color:#d9e2f3; color:#0070c0; width:59px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:79px" %)**[bit7:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:110px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:106px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:167px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:171px" %)**bit0**
479 -|(% style="width:76px" %)**Value**|(% style="width:96px" %)Reserve|(% style="width:110px" %)(((
480 -Count mod
481 -)))|(% style="width:106px" %)TDC flag 0:No;1:Yes|(% style="width:167px" %)(((
482 -0: No Alarm; 1: Alarm
363 +[ALARM, DOOR_OPEN_STATUS, DOOR_OPEN_TIMES,LAST_DOOR_OPEN_DURATION, TIME]
483 483  
484 -(PA8)
485 -)))|(% style="width:171px" %)(((
486 -Status 0: Close; 1:Open
487 487  
488 -(PA8)
489 -)))
366 +[FALSE, CLOSE, 0, 0, 2021-11-12 12:35:27],
490 490  
491 -**Status2 & Alarm2:**
368 +[FALSE, OPEN,  1, 0, 2021-11-12 12:36:34],
492 492  
493 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:550px" %)
494 -|(% style="background-color:#d9e2f3; color:#0070c0; width:59px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:113px" %)**[bit7:bit2]**|(% style="background-color:#d9e2f3; color:#0070c0; width:176px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:175px" %)**bit0**
495 -|(% style="width:76px" %)**Value**|(% style="width:113px" %)Reserve|(% style="width:176px" %)(((
496 -0: No Alarm; 1: Alarm
370 +[FALSE, CLOSE, 1, 2, 2021-11-12 12:39:00],
497 497  
498 -(PA4)
499 -)))|(% style="width:175px" %)(((
500 -Status 0: Close,;1:Open
372 +[FALSE, OPEN,  2, 2, 2021-11-12 12:39:17],
501 501  
502 -(PA4)
503 -)))
374 +[FALSE, CLOSE, 2, 1, 2021-11-12 12:40:38],
504 504  
505 -[[image:image-20230630155908-6.png||height="295" width="927"]]
376 +[FALSE, CLOSE, 2, 1, 2021-11-12 14:35:19],
506 506  
378 +[FALSE, OPEN,  3, 1, 2021-11-12 14:50:32],
507 507  
508 -=== 2.3.4  Historical Door Open/Close Event, FPORT~=3 ===
380 +[FALSE, CLOSE, 3, 2, 2021-11-12 14:53:02],
509 509  
382 +[FALSE, OPEN,  4, 2, 2021-11-12 14:58:35],
510 510  
511 -DS03A-LB stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.5DatalogFeature"]].
384 +[FALSE, CLOSE, 4, 0, 2021-11-12 14:59:28],
512 512  
513 -The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time open/close status.
514 514  
515 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
516 -|=(% colspan="5" style="background-color:#D9E2F3;color:#0070C0;width:515px" %)**Real-Time Open/Close Status, FPORT=3**
517 -|(% style="width:94px" %)**Size(bytes)**|(% style="width:97px" %)**1**|(% style="width:95px" %)**3**|(% style="width:119px" %)**3**|(% style="width:107px" %)**4**
518 -|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
519 -Status
387 +=== 2.3.4  Sensor Configuration, FPORT~=4 ===
520 520  
521 -&[[Alarm>>||anchor="H3.3.4A0AlarmBaseonTimeout"]]
522 -)))|(% style="width:95px" %)Total open door events|(% style="width:119px" %)(((
523 -The last door open duration (unit: sec)
524 -)))|(% style="width:108px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
525 525  
526 -**Status & Alarm:**
390 +DS03A-LB will only send this command after getting the downlink command (0x26 02) from the server.
527 527  
528 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:755px" %)
529 -|(% style="background-color:#d9e2f3; color:#0070c0; width:59px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:88px" %)**bit7**|(% style="background-color:#d9e2f3; color:#0070c0; width:92px" %)**bit6**|(% style="background-color:#d9e2f3; color:#0070c0; width:89px" %)**[bit5:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:90px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:95px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:116px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:112px" %)**bit0**
530 -|(% style="width:76px" %)**Value**|(% style="width:88px" %)No ACK message|(% style="width:92px" %)Poll Message Flag|(% style="width:89px" %)Reserve|(% style="width:90px" %)(((
531 -Count mod
532 -)))|(% style="width:95px" %)TDC flag 0:No;1:Yes|(% style="width:116px" %)(((
533 -0: No Alarm;
392 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
393 +|(% colspan="5" style="background-color:#d9e2f3; color:#0070c0; width:504px" %)**Sensor Configuration FPORT=4**
394 +|**Size(bytes)**|(% style="width:75px" %)**3**|(% style="width:77px" %)**1**|(% style="width:96px" %)**1**|(% style="width:158px" %)**2**
395 +|**Value**|(% style="width:75px" %)TDC (unit:sec)|(% style="width:77px" %)Disalarm|(% style="width:96px" %)Keep status|(% style="width:158px" %)Keep time (unit: min)
534 534  
535 -1: Alarm
536 -)))|(% style="width:112px" %)(((
537 -Status 0:Close;
397 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/image-20220609110123-5.png?rev=1.1||alt="image-20220609110123-5.png"]]
538 538  
539 -1: Open
540 -)))
541 541  
542 542  * (((
543 -Each data entry is 11 bytes and has the same structure as [[Real-Time open/close status>>||anchor="H2.3.2A0Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]], to save airtime and battery, DS03A-LB will send max bytes according to the current DR and Frequency bands.
401 +**TDC: (default: 0x001C20)**
544 544  )))
545 545  
546 -For example, in the US915 band, the max payload for different DR is:
404 +Uplink interval for the Open/Close Event, default value is 0x001C20 which is 7200 seconds = 2 hours.
547 547  
548 -(((
549 -**~1. DR0**: max is 11 bytes so one entry of data
550 -)))
551 551  
552 -(((
553 -**2. DR1**: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
407 +* (((
408 +**Disalarm: (default: 0)**
554 554  )))
555 555  
556 -(((
557 -**3. DR2**: total payload includes 11 entries of data
558 -)))
411 + **If Disalarm = 1**, DS03A-LB will only send uplink at every TDC periodically. This is normally use for pulse meter application, in this application, there are many open/close event, and platform only care about the total number of pulse.
559 559  
560 -(((
561 -**4. DR3**: total payload includes 22 entries of data.
562 -)))
413 + **If Disalarm = 0**, DS03A-LB will send uplink at every TDC periodically and send data on each open/close event. This is useful for the application user need to monitor the open/close event in real-time.
563 563  
564 -If DS03A-LB doesn't have any data in the polling time. It will uplink 11 bytes of 0
565 565  
566 -[[image:image-20230630155556-4.png||height="146" width="938"]]
416 +**~ Note: When Disalarm=0, a high frequently open/close event will cause lots of uplink and drain battery very fast. **
567 567  
568 -**Downlink:**
569 569  
570 -0x31 64 9E 7D 34 64 9E 7E 9C 05
419 +* (((
420 +**Keep Status & Keep Time**
421 +)))
571 571  
423 +Shows the configure value of [[Alarm Base on Timeout Feature>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H3.8A0AlarmBaseonTimeout]]
572 572  
573 -**Uplink:**
425 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/image-20220609110018-4.png?width=1159&height=291&rev=1.1||alt="image-20220609110018-4.png" height="291" width="1159"]]
574 574  
575 -45 00 00 00 00 00 00 64 9E 7D 48 40 00 00 00 00 00 63 64 9E 7D 9C 41 00 00 01 00 00 63 64 9E 7D A4 40 00 00 01 00 00 8D 64 9E 7E 31 43 00 00 02 00 00 8D 64 9E 7E 44 48 00 00 02 00 00 1F 64 9E 7E 59 4B 00 00 03 00 00 1F 64 9E 7E 6B
576 576  
577 -
578 -**Parsed Value:**
579 -
580 -[COUNTMOD, TDC_FLAG, ALARM,  DOOR_STATUS, OPEN_DOOR_TIMES, LAST_DOOR_OPEN_DURATION, TIME]
581 -
582 -
583 -[SUM,YES,FALSE,OPEN,0,0,2023-06-30 06:59:20],
584 -
585 -[SUM,NO,FALSE,CLOSE,0,99,2023-06-30 07:00:44],
586 -
587 -[SUM,NO,FALSE,OPEN, 1,99,2023-06-30 07:00:52],
588 -
589 -[SUM,NO,FALSE,CLOSE,1,141,2023-06-30 07:03:13],
590 -
591 -[SUM,NO,TRUE,OPEN, 2,141,2023-06-30 07:03:32],
592 -
593 -[PART,NO,FALSE,CLOSE,2,31,2023-06-30 07:03:53],
594 -
595 -[PART,NO,TRUE,OPEN, 3,31,2023-06-30 07:04:11],
596 -
597 -[[image:image-20230630172740-1.png||height="199" width="868"]]
598 -
599 -
600 600  == 2.4 Payload Decoder file ==
601 601  
602 602  
... ... @@ -612,15 +612,13 @@
612 612  == 2.5 Datalog Feature ==
613 613  
614 614  
615 -(% style="color:blue" %)**Datalog Feature** (%%)is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DS03A-LB will store the reading for future retrieving purposes.
443 +**Datalog Feature** is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, DS03A-LB will store the reading for future retrieving purposes.
616 616  
617 -(% style="color:red" %)**Note:After the device is reset,in cumulative counting mode,the last stored count value will be read as the initial value.**
618 618  
619 -
620 620  === 2.5.1 Ways to get datalog via LoRaWAN ===
621 621  
622 622  
623 -Set PNACKMD=1, DS03A-LB will wait for ACK for every uplink, when there is no LoRaWAN network,DS03A-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
449 +Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayloadA028FPORT3D329"]], DS03A-LB will wait for ACK for every uplink, when there is no LoRaWAN network,DS03A-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
624 624  
625 625  * a) DS03A-LB will do an ACK check for data records sending to make sure every data arrive server.
626 626  * b) DS03A-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but DS03A-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if DS03A-LB gets a ACK, DS03A-LB will consider there is a network connection and resend all NONE-ACK Message.
... ... @@ -629,7 +629,6 @@
629 629  
630 630  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="image-20220703111700-2.png" height="381" width="1119"]]
631 631  
632 -
633 633  === 2.5.2 Unix TimeStamp ===
634 634  
635 635  
... ... @@ -658,41 +658,31 @@
658 658  
659 659  == 2.6 ​Show Data in DataCake IoT Server ==
660 660  
661 -
662 662  Datacake IoT platform provides a human-friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:
663 663  
664 664  
665 -(% style="color:blue" %)**Step 1:**(%%)** Link TTNv3 to Datacake.**[[https:~~/~~/docs.datacake.de/lorawan/lns/thethingsindustries#create-integration-on-tti>>url:https://docs.datacake.de/lorawan/lns/thethingsindustries#create-integration-on-tti]]
489 +**Step 1: Link TTNv3 to Datacake.**[[https:~~/~~/docs.datacake.de/lorawan/lns/thethingsindustries#create-integration-on-tti>>url:https://docs.datacake.de/lorawan/lns/thethingsindustries#create-integration-on-tti]]
666 666  
667 -(% style="color:blue" %)**Step 2:**(%%)** Configure DS03A-LB in Datacake.**
491 +**Step 2: Configure DS03A-LB in Datacake.**
668 668  
669 669  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746350207-427.png?rev=1.1||alt="1654746350207-427.png"]]
670 670  
671 -
672 672  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654747162439-840.png?rev=1.1||alt="1654747162439-840.png"]]
673 673  
674 -
675 675  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746405400-203.png?rev=1.1||alt="1654746405400-203.png"]]
676 676  
677 -
678 678  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746763908-732.png?rev=1.1||alt="1654746763908-732.png"]]
679 679  
680 -
681 681  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746716087-684.png?rev=1.1||alt="1654746716087-684.png"]]
682 682  
683 -
684 684  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746693868-718.png?rev=1.1||alt="1654746693868-718.png"]]
685 685  
686 -
687 687  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746674738-826.png?rev=1.1||alt="1654746674738-826.png"]]
688 688  
689 -
690 690  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746646379-591.png?rev=1.1||alt="1654746646379-591.png"]]
691 691  
692 -
693 693  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746549277-209.png?rev=1.1||alt="1654746549277-209.png"]]
694 694  
695 -
696 696  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654746593411-887.png?rev=1.1||alt="1654746593411-887.png"]]
697 697  
698 698  
... ... @@ -707,9 +707,11 @@
707 707  == 2.8 ​Firmware Change Log ==
708 708  
709 709  
710 -**Firmware download link: **[[https:~~/~~/www.dropbox.com/sh/b0uwyzjs4px4eao/AADvI7fPRwsFKTglEmaRRuaaa?dl=0>>https://www.dropbox.com/sh/b0uwyzjs4px4eao/AADvI7fPRwsFKTglEmaRRuaaa?dl=0]]
525 +**Firmware download link:**
711 711  
527 +[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
712 712  
529 +
713 713  = 3. Configure DS03A-LB =
714 714  
715 715  == 3.1 Configure Methods: ==
... ... @@ -723,7 +723,6 @@
723 723  
724 724  == 3.2 General Commands ==
725 725  
726 -
727 727  These commands are to configure:
728 728  
729 729  * General system settings like: uplink interval.
... ... @@ -740,7 +740,7 @@
740 740  These commands only valid for DS03A-LB, as below:
741 741  
742 742  
743 -=== 3.3.1  Set Transmit Interval Time ===
559 +=== 3.3.1 Set Transmit Interval Time ===
744 744  
745 745  
746 746  Feature: Change LoRaWAN End Node Transmit Interval.
... ... @@ -748,7 +748,7 @@
748 748  (% style="color:blue" %)**AT Command: AT+TDC**
749 749  
750 750  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
751 -|=(% style="width: 156px;background-color:#D9E2F3; color:#0070c0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3; color:#0070c0" %)**Function**|=(% style="background-color:#D9E2F3; color:#0070c0" %)**Response**
567 +|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**
752 752  |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
753 753  30000
754 754  OK
... ... @@ -768,19 +768,25 @@
768 768  * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
769 769  * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
770 770  
771 -=== 3.3.2  Enable / Disable Alarm ===
587 +=== 3.3.2 Get Device Status ===
772 772  
773 773  
590 +Send a LoRaWAN downlink to ask device send Alarm settings.
591 +
592 +* (% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
593 +
594 +Sensor will upload Device Status via FPORT=5. See payload section for detail.
595 +
596 +
597 +=== 3.3.3  Enable / Disable Alarm ===
598 +
774 774  Feature: Enable/Disable Alarm for open/close event. Default value 0.
775 775  
776 -(% style="color:blue" %)**AT Command: **
601 +**AT Command:**
777 777  
778 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
779 -|(% style="background-color:#d9e2f3; color:#0070c0; width:154px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:278px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0; width:88px" %)**Response**
780 -|(% style="width:154px" %)AT+DISALARM=1|(% style="width:278px" %)End node will only send packets in TDC time.|OK
781 -|(% style="width:154px" %)AT+DISALARM=0|(% style="width:278px" %)End node will send packets in TDC time or status change for door sensor|OK
603 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/image-20220609140712-1.png?rev=1.1||alt="image-20220609140712-1.png"]]
782 782  
783 -(% style="color:blue" %)**Downlink Command: **
605 +**Downlink Command:**
784 784  
785 785  0xA7 01  ~/~/ Same As AT+DISALARM=1
786 786  
... ... @@ -787,268 +787,182 @@
787 787  0xA7 00  ~/~/ Same As AT+DISALARM=0
788 788  
789 789  
790 -=== 3.3.3  Alarm Base on Timeout ===
612 +=== 3.3.4  Alarm Base on Timeout ===
791 791  
792 -
793 793  DS03A-LB can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:
794 794  
795 795  
796 796  * (((
797 -(% style="color:blue" %)**Keep Status: Status to be monitor**
618 +**Keep Status: Status to be monitor**
798 798  )))
799 799  
800 -(% style="color:#037691" %)**Keep Status = 1**(%%): Monitor Close to Open event
621 +Keep Status = 1: Monitor Close to Open event
801 801  
802 -(% style="color:#037691" %)**Keep Status = 0**(%%): Monitor Open to Close event
623 +Keep Status = 0: Monitor Open to Close event
803 803  
804 804  
805 805  * (((
806 -(% style="color:blue" %)**Keep Time: Timeout to send an Alarm**
627 +**Keep Time: Timeout to send an Alarm**
807 807  )))
808 808  
809 809  Range 0 ~~ 65535(0xFFFF) seconds.
810 810  
811 -If (% style="color:#037691" %)**keep time = 0**(%%), Disable Alarm Base on Timeout feature.
632 +If keep time = 0, Disable Alarm Base on Timeout feature.
812 812  
813 -If (% style="color:#037691" %)**keep time > 0**(%%), device will monitor the keep status event and send an alarm when status doesn't change after timeout.
634 +If keep time > 0, device will monitor the keep status event and send an alarm when status doesn't change after timeout.
814 814  
815 815  
816 -* (((
817 -(% style="color:blue" %)**Downlink Command**
818 -)))
637 +**AT Command to configure:**
819 819  
820 -(% style="color:#037691" %)**Command: 0xA9 aa bb cc dd**
821 -
822 -**A9:** Command Type Code
823 -
824 -**aa: **01:TTRIG1; 02:TTRIG2
825 -
826 -**bb:** status to be monitored
827 -
828 -**cc dd:** timeout.
829 -
830 -
831 -1)**AT+TTRIG1**:(PA8 of pin)
832 -
833 -(% style="color:blue" %)**AT Command to configure:**
834 -
835 835  * (((
836 -(% style="color:#037691" %)**AT+TTRIG1=1,30** (%%) **~-~->** When the **Keep Status** change from close to open, and device remains in open status for more than 30 seconds. DS03A-LB will send an uplink packet, the Alarm1 bit(the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
837 -
838 -(% style="color:#037691" %)**AT+TTRIG1=0,30** (%%) **~-~->** When the **Keep Status** change from open to close, and device remains in open status for more than 30 seconds. DS03A-LB will send an uplink packet, the Alarm1 bit (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
640 +**AT+TTRIG=1,30**  **~-~->** When the **Keep Status** change from close to open, and device remains in open status for more than 30 seconds. LDS03A will send an uplink packet, the [[Alarm bit>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/#H2.3.3A0Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
839 839  )))
840 840  
841 841  * (((
842 -(% style="color:#037691" %)**AT+TTRIG1=0,0**  (%%) **~-~-> ** Default Value, disable timeout Alarm.
843 -
844 -
845 -
644 +**AT+TTRIG=0,0**   **~-~-> ** Default Value, disable timeout Alarm.
846 846  )))
847 847  
848 -(% style="color:blue" %)**Downlink Command to configure:**
647 +**Downlink Command to configure:**
849 849  
850 -If user send 0xA9 01 01 00 1E: equal to AT+TTRIG1=1,30 or
649 +**Command: 0xA9 aa bb cc**
851 851  
852 - 0xA9 01 00 00 00: Equal to AT+TTRIG1=0,0.
651 +**A9:** Command Type Code
853 853  
653 +**aa:** status to be monitored
854 854  
855 -2)**AT+TTRIG2**:(PA4 of pin,need to use AT+TTRCHANNEL=2)
655 +**bb cc:** timeout.
856 856  
857 -(% style="color:blue" %)**AT Command to configure:**
858 858  
859 -* (((
860 -(% style="color:#037691" %)**AT+TTRIG2=1,30** (%%) **~-~->** When the **Keep Status** change from close to open, and device remains in open status for more than 30 seconds. DS03A-LB will send an uplink packet, the Alarm2 bit (the second bit of 12^^st^^ byte of payload) on this uplink packet is set to 1.
658 +If user send 0xA9 01 00 1E: equal to AT+TTRIG=1,30
861 861  
862 -(% style="color:#037691" %)**AT+TTRIG2=0,30** (%%) **~-~->** When the **Keep Status** change from open to close, and device remains in open status for more than 30 seconds. DS03A-LB will send an uplink packet, the Alarm2 bit (the second bit of 12^^st^^ byte of payload) on this uplink packet is set to 1.
863 -)))
660 +Or
864 864  
865 -* (((
866 -(% style="color:#037691" %)**AT+TTRIG2=0,0**  (%%) **~-~-> ** Default Value, disable timeout Alarm.
662 +0xA9 00 00 00: Equal to AT+TTRIG=0,0. Disable timeout Alarm.
867 867  
868 868  
869 -
870 -)))
871 -
872 -(% style="color:blue" %)**Downlink Command to configure:**
873 -
874 -If user send 0xA9 02 00 00 1E: equal to AT+TTRIG2=0,30 or
875 -
876 - 0xA9 02 00 00 00: Equal to AT+TTRIG2=0,0.
877 -
878 -
879 -=== 3.3.4  TTRIG1 & TTRIG2 timeout status alarm ===
880 -
881 -
882 -It needs to be used with AT+TTRIG1 or AT+TTRIG2. When TTRIG1 or TTRIG2 times out and causes an alarm, and the status does not change subsequently, an alarm packet will be sent at the alarm interval.
883 -
884 -(% style="color:blue" %)**AT Command:**
885 -
886 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
887 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 279px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 76px;background-color:#D9E2F3;color:#0070C0" %)**Response**
888 -|(% style="width:155px" %)(((
889 -AT+TTRALARM=0
890 -)))|(% style="width:279px" %)(((
891 -disable continuous alarm
892 -)))|(% style="width:84px" %)(((
893 -OK
894 -)))
895 -|(% style="width:155px" %)(((
896 -AT+TTRALARM=60
897 -)))|(% style="width:279px" %)(((
898 -The alarm interval is 60 minutes (unit: minutes)
899 -)))|(% style="width:84px" %)(((
900 -OK
901 -)))
902 -
903 -(% style="color:blue" %)**Downlink Command:**
904 -
905 -Example:  0C aa  => AT+TTRALARM= aa
906 -
907 -
908 908  === 3.3.5  Count Mod ===
909 909  
667 +**AT Command:**
910 910  
911 -Feature: Manually set the count mode.
912 -
913 -(% style="color:blue" %)**AT Command:**
914 -
915 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
916 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 277px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 88px;background-color:#D9E2F3;color:#0070C0" %)**Response**
917 -|(% style="width:155px" %)(((
669 +|=**Command Example**|=**Function**|=**Response**
670 +|(((
918 918  AT+COUNTMOD=0
919 -)))|(% style="width:277px" %)(((
672 +)))|(((
920 920  the count value keeps accumulating mode
921 -)))|(% style="width:86px" %)(((
674 +)))|(((
675 +
676 +
922 922  OK
923 923  )))
924 -|(% style="width:155px" %)(((
679 +|(((
925 925  AT+COUNTMOD=1
926 -)))|(% style="width:277px" %)(((
681 +)))|(((
927 927  the count value will be reset after each TDC time（Last Close Duration Reset after each uplink）
928 -)))|(% style="width:86px" %)(((
683 +)))|(((
929 929  OK
930 930  )))
931 931  
932 -(% style="color:blue" %)**Downlink Command:**
687 +**Downlink Command:**
933 933  
934 934  Example:  0B aa  => AT+COUNTMOD = second byte
935 935  
936 936  
937 -=== 3.3.6  Number of channel of door sensors ===
692 +=== 3.3.6  Interrupt Pin Channel Mod ===
938 938  
694 +**AT Command:**
939 939  
940 -Feature: Set the number of door sensor channels.
941 -
942 -(% style="color:blue" %)**AT Command:**
943 -
944 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
945 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 259px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 57px;background-color:#D9E2F3;color:#0070C0" %)**Response**
946 -|(% style="width:155px" %)(((
696 +|=**Command Example**|=**Function**|=**Response**
697 +|(((
947 947  AT+TTRCHANNEL=1
948 -)))|(% style="width:259px" %)(((
949 -Set as single channel, only use PA8 pin as interrupt pin.
950 -)))|(% style="width:44px" %)(((
699 +)))|(((
700 +set as single channel, only use PB14 pin as interrupt pin.
701 +)))|(((
702 +
703 +
951 951  OK
952 952  )))
953 -|(% style="width:155px" %)(((
706 +|(((
954 954  AT+TTRCHANNEL=2
955 -)))|(% style="width:259px" %)(((
956 -Set as dual channel, use PA8 pin and PA4 pin as interrupt pin.
957 -)))|(% style="width:44px" %)(((
708 +)))|(((
709 +is set as dual channel, use PB14 pin and PB15 pin as interrupt pin.
710 +)))|(((
958 958  OK
959 959  )))
960 960  
961 -(% style="color:blue" %)**Downlink Command:**
714 +**Downlink Command:**
962 962  
963 963  Example:  0D aa => AT+TTRCHANNEL = second byte
964 964  
965 965  
966 -=== 3.3.7  Set Time Sync Mode ===
719 +=== 3.3.7  Change the name of AT+TTRIG to AT+TTRIG1 ===
967 967  
721 +**Downlink Command:**
968 968  
969 -Feature: Enable/Disable Sync system time via LoRaWAN MAC Command (DeviceTimeReq), LoRaWAN server must support v1.0.3 protocol to reply to this command.
723 +Example:  A9 01 aa bb cc  => AT+TTRIG1= third byte, 4th byte and 5th byte
970 970  
971 -SYNCMOD is set to 1 by default. If user wants to set a different time from the LoRaWAN server, the user needs to set this to 0.
972 972  
973 -(% style="color:blue" %)**AT Command:**
726 +=== 3.3.8  Added AT+TTRIG2 for PB15 pin ===
974 974  
975 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
976 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 259px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 57px;background-color:#D9E2F3;color:#0070C0" %)**Response**
977 -|(% style="width:155px" %)(((
978 -AT+SYNCMOD=1
979 -)))|(% style="width:259px" %)(((
980 -Enable Sync system time via LoRaWAN MAC Command (DeviceTimeReq) The default is zero time zone.
981 -)))|(% style="width:44px" %)(((
982 -OK
983 -)))
984 -|(% style="width:155px" %)(((
985 -AT+SYNCMOD=1,8
986 -)))|(% style="width:259px" %)(((
987 -Enable Sync system time via LoRaWAN MAC Command (DeviceTimeReq) Set to East eight time zone.
988 -)))|(% style="width:44px" %)(((
989 -OK
990 -)))
991 -|(% style="width:155px" %)AT+SYNCMOD=1,-12|(% style="width:259px" %)Enable Sync system time via LoRaWAN MAC Command (DeviceTimeReq) Set to West Twelve Time Zone.|(% style="width:44px" %)OK
728 +**Downlink Command:**
992 992  
993 -(% style="color:blue" %)**Downlink Command:**
730 +Example: A9 02 aa bb cc  => AT+TTRIG2= third byte, 4th byte and 5th byte
994 994  
995 -0x28 01  ~/~/ Same As AT+SYNCMOD=1
996 996  
997 -0x28 01 08  ~/~/ Same As AT+SYNCMOD=1,8
733 +=== 3.3.9  TTRIG1/2 timeout status alarm ===
998 998  
999 -0x28 01 F4  ~/~/ Same As AT+SYNCMOD=1,-12
735 +It needs to be used with AT+TTRIG1 or AT+TTRIG2. When TTRIG1 or TTRIG2 times out and causes an alarm, and the status does not change subsequently, an alarm packet will be sent at the alarm interval.
1000 1000  
1001 -0x28 00  ~/~/ Same As AT+SYNCMOD=0
737 +**AT Command:**
1002 1002  
739 +|=**Command Example**|=**Function**|=**Response**
740 +|(((
741 +AT+TTRALARM=0
742 +)))|(((
743 +disable continuous alarm
744 +)))|(((
745 +
1003 1003  
1004 -=== 3.3.8  Clear the open door times and the duration of the last open door ===
747 +OK
748 +)))
749 +|(((
750 +AT+TTRALARM=60
751 +)))|(((
752 + The alarm interval is 60 minutes (unit: minutes)
753 +)))|(((
754 +OK
755 +)))
1005 1005  
757 +**Downlink Command:**
1006 1006  
1007 -(% style="color:blue" %)**AT Command:**
759 +Example:  0C aa  => AT+TTRALARM= aa
1008 1008  
1009 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
1010 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 259px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 57px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1011 -|(% style="width:155px" %)AT+CLRC|(% style="width:259px" %)clear the open door times and the duration of the last open door.|(% style="width:44px" %)(((
1012 -OK
1013 -)))
1014 1014  
1015 -(% style="color:blue" %)**Downlink Command:**(%%)0xA6 01
762 +=== 3.3.9  Select counting mode ===
1016 1016  
1017 -The sensor will clear the open door times and the duration of the last open door.
764 +**AT+TTRMODx=a,b**
1018 1018  
766 +When **a=0**, the door is opened to count, and when **a=1**,the closed door is counted.
1019 1019  
1020 -=== 3.3.9  Set the count value of the number of open door ===
768 +When **b=0**, it is the last door open duration, and when **b=1**,the last door close duration.
1021 1021  
770 +**AT Command:**
1022 1022  
1023 -(% style="color:blue" %)**AT Command:**
772 +|=**Command Example**|=**Function**|=**Response**
773 +|(((
774 +AT+TTRMODx=1,0
775 +)))|Door closed count and record the last door opened duration|(((
776 +
1024 1024  
1025 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
1026 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 259px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 57px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1027 -|(% style="width:155px" %)(((
1028 -AT+SETCNT=1,100
1029 -)))|(% style="width:259px" %)(((
1030 -Set the open door times of PA8 pin to 100 times.
1031 -)))|(% style="width:44px" %)(((
1032 1032  OK
1033 1033  )))
1034 -|(% style="width:155px" %)AT+SETCNT=1,0|(% style="width:259px" %)Clear the open door times of PA8 pin.|(% style="width:44px" %)OK
1035 -|(% style="width:155px" %)(((
1036 -AT+SETCNT=2,50
1037 -)))|(% style="width:259px" %)(((
1038 -Set the open door times of PA4 pin to 100 times.
1039 -)))|(% style="width:44px" %)(((
780 +|(((
781 +AT+TTRMODx=0,1
782 +)))|(((
783 +Door opened count and record the last door Door Door open closed duration
784 +)))|(((
1040 1040  OK
1041 1041  )))
1042 1042  
1043 -(% style="color:blue" %)**Downlink Command:**
1044 -
1045 -0xA6 01 00 00 64  ==>  AT+SETCNT=1,100
1046 -
1047 -0xA6 01 00 00 00  ==>  AT+SETCNT=1,0
1048 -
1049 -0xA6 02 00 00 32  ==>  AT+SETCNT=2,50
1050 -
1051 -
1052 1052  = 4. Battery & Power Consumption =
1053 1053  
1054 1054  
... ... @@ -1069,10 +1069,10 @@
1069 1069  Firmware and changelog can be downloaded from : **[[Firmware download link>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
1070 1070  
1071 1071  
1072 -**Methods to Update Firmware:**
808 +Methods to Update Firmware:
1073 1073  
1074 -* (Recommanded way) OTA firmware update via wireless:** [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
1075 -* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
810 +* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
811 +* Update through UART TTL interface. **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
1076 1076  
1077 1077  = 6. FAQ =
1078 1078  
... ... @@ -1123,4 +1123,4 @@
1123 1123  
1124 1124  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1125 1125  
1126 -* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].
862 +* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
image-20230522092858-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -156.5 KB
Content
image-20230522092934-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -156.5 KB
Content
image-20230522093256-3.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -34.5 KB
Content
image-20230630155406-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -41.8 KB
Content
image-20230630155451-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -77.2 KB
Content
image-20230630155527-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -39.2 KB
Content
image-20230630155556-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -38.4 KB
Content
image-20230630155751-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20230630155908-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -90.8 KB
Content
image-20230630160843-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -511.7 KB
Content
image-20230630172740-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -37.1 KB
Content
image-20230701094042-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Saxer
Size
... ... @@ -1,1 +1,0 @@
1 -34.5 KB
Content