PG1302 - LoRaWAN Concentrator User Manual

The PG1302 is a (% style="color:green" %)**multi-channel high-performance transmitter/receiver**(%%) designed to simultaneously receive several LoRa packets using random spreading factors on random channels. Its goal is to enable robust connection between a central wireless data concentrator and a massive amount of wireless end-points spread over a very wide range of distances.

23

24

The PG1302 is designed to use with Raspberry Pi to build smart metering fixed networks and Internet of Things applications with up to 5000 nodes per km2 in a moderately interfered environment.

25

26

PG1302 is fully compatible with (% style="color:green" %)**RPi3/4 or Tinker Board**(%%), users can use the pre-build OS from Dragino to set up and easy to use the module by Web UI. Or install the raw LoRaWAN driver in the existing OS.

27

28

29

== **1.2 Features** ==

30

31

* Base on Semtech SX1302 solution

32

* Support Raspberry Pi 3B/3B+/4

33

* Up to -140dBm sensitivity

34

* Support 3.3v and 5v.

35

* Mini-PCIe Interface

36

* Converter board to support Raspberry Pi

37

38

== **1.3 General Interfaces for PG1302** ==

39

40

* SPI interface for LoRa

41

* Power Input: 5v, 1A

42

* 1 x I-PEX for LoRa

43

44

== **1.4 Pin Mapping** ==

45

46

[[image:1651743282627-547.png||height="402" width="425"]]

== **1.5 LEDs** ==

TX: Blink when transmit a packet

51

RX: Blink when receive a packet

Config: Always ON

== **1.6 Power Consumption** ==

<300mA @ 3.3v.

Detail Test Report see [[this link>>https://www.dropbox.com/sh/89virm4y0b02c7i/AAA-cgQEsSc8gNGFYAB0qZ_Za?dl=0]]

60

61

62

== **1.7 Applications** ==

63

64

* Smart Buildings & Home Automation

65

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

= **2. Example: Set up as LoRaWAN gateway.** =

72

73

== **2.1 System structure** ==

74

75

76

This example is an example to show how to set up the PG1302 + RPi as a LoRaWAN gateway to use with [[TheThingsNetwork>>url:http://www.thethingsnetwork.org/]](TTN) LoRaWAN server. Set up method for other server are similar.

77

78

[[image:1651743698677-436.png||height="457" width="686"]]

79

80

81

== **2.2 Hardware Installation** ==

82

83

(% style="color:red" %)**Important Notice: Please power the RPI with 5V,3A cable.**

84

85

[[image:image-20220621104746-1.png||height="381" width="451"]]

86

87

88

= **3. Install the software?** =

89

90

There are two ways to install the software in RPi4 to use PG1302.

91

92

* Flash SD card with Dragino pre-build image which supports Web UI.

93

* Install Lora packet forwarder in existing RPi OS.

94

95

= **4. Flash with pre-build image** =

96

97

== **4.1 Download the dragino image for RPI** ==

98

99

Download PG1302_for_Rpi4_64_with_webui from

100

[[https:~~/~~/www.dropbox.com/sh/f6nbldh1qbspya5/AACgL6pDkwdBQO1BQqq_Nubwa?dl=0>>https://www.dropbox.com/sh/f6nbldh1qbspya5/AACgL6pDkwdBQO1BQqq_Nubwa?dl=0]]

101

102

103

== **4.2 Flash the image to an SD card** ==

104

105

Flash the image to the SD card:

106

107

[[image:1651744119133-233.png||height="373" width="621"]]

108

109

Note: Download the flash tool following this link

110

111

[[https:~~/~~/www.balena.io/etcher/>>https://www.balena.io/etcher/]]

112

113

114

== **4.3 Access the Linux console** ==

115

116

Connect the RPI Ethernet port to your router, RPi will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the RPI. You can use this IP to connect the WEB UI or SSH access of RPI. Make sure your PC and the RPI is in the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it. Below are screenshots

117

118

[[image:1651744193675-591.png||height="450" width="466"]]

119

120

The account details for Web Login are:

121

122

(((

123

**~ (% style="color:#0000ff" %)User Name: root(%%)**

)))

(((

**~ (% style="color:#0000ff" %)Password: dragino(%%)**

)))

(((

)))

(((

**~ (% style="color:#0000ff" %)Backup account(%%)**

)))

(((

**~ (% style="color:#0000ff" %)Pi/dragino(%%)**

)))

After logging in, you will be in the Linux console and type the command here.

145

146

[[image:1651744358515-107.png||height="366" width="581"]]

147

148

149

== **4.4 Access the WebUI of RPi4.** ==

150

151

=== **4.4.1 Home page** ===

152

153

Open a browser on the PC and type the RPI ip address[[http:~~/~~/IP_ADDRESS** **>>url:http://192.168.1.xx/]] (If the IP is assigned by the uplink router)

154

You will see the login interface of RPI as shown below.

155

The account details for Web Login are:

156

157

(((

158

**~ (% style="color:#0000ff" %)User Name: root(%%)**

159

(% style="color:#0000ff" %)** Password: dragino**

160

)))

161

162

[[image:1651744457761-993.png||height="352" width="621"]]

163

164

165

=== **4.4.2 LoRa Page** ===

166

167

This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customize the band* as well.

168

169

[[image:1651744554845-970.png||height="328" width="621"]]

170

171

Different PG1302 hardware version can support different frequency range:

172

173

➢ 868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

174

175

➢ 915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

176

177

After user choose the frequency plan, he can see the actually frequency in used by checking the

178

179

page LogRead ~-~-> LoRa Log

180

181

Note *: [[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]

182

183

184

=== **4.4.3 LoRaWAN Page** ===

185

186

==== **4.4.3.1 Semtech UDP** ====

187

188

[[image:1651744767914-283.png||height="352" width="621"]]

189

190

Note *: [[See this instruction for how to configure TTN>>doc:Main.Notes for TTN.WebHome]].

191

192

193

==== **4.4.3.2 Basic Station** ====

194

195

[[image:1651744890629-683.png||height="380" width="621"]]

196

197

Note *: [[See this instruction for how to configure AWS-loT-Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].

198

199

200

=== **4.4.4 LogRead** ===

201

202

==== **4.4.4.1 LoRa Log** ====

203

204

[[image:1651744955955-452.png||height="571" width="621"]]

205

206

Show the frequency for LoRa Radio and traffics.

207

208

209

==== **4.4.4.2 System Log** ====

Show system log.

[[image:1651745003470-264.png||height="477" width="621"]]

214

215

216

==== **4.4.4.3 Record Log** ====

217

218

**Record the system log.**

219

220

[[image:1651745069814-662.png||height="144" width="621"]]

221

222

223

= **5. Install stand-alone LoRa Packet Forwarder.** =

224

225

== **5.1 OS requirement** ==

226

227

RPI in this example is RPI model 4B with fresh Raspbian OS install.

(% class="box" %)

(((

pi@raspberrypi:~~$ cat /etc/os-release

232

PRETTY_NAME="Raspbian GNU/Linux 8 (jessie)"

233

NAME="Raspbian GNU/Linux"

VERSION_ID="8"

VERSION="8 (jessie)"

ID=raspbian

ID_LIKE=debian

HOME_URL="http:~/~/www.raspbian.org/"

239

SUPPORT_URL="http:~/~/www.raspbian.org/RaspbianForums"

240

BUG_REPORT_URL="http:~/~/www.raspbian.org/RaspbianBugs"

)))

== **5.2 Get Gateway ID in Raspberry and input this in TTN v3.** ==

246

247

In RPI, run the below command to get a Gateway ID

248

249

(% class="box infomessage" %)

(((

ifconfig eth0

)))

[[image:1651745210205-512.png||height="130" width="621"]]

(((

(((

We got the ether (eth0 MAC) address is b8:27:eb:49:62:bc). Add ffff at the end and remove “:” to get the gateway ID: b827ebxxxxbcffff. Input this to TTN v3. Make sure to select legacy packet forwarder.

)))

)))

[[image:1651745267862-321.png||height="526" width="621"]]

263

264

[[image:1651745306744-481.png||height="478" width="621"]]

265

266

After set up, the status should show not connected as below:

267

268

[[image:1651745366987-458.png||height="363" width="621"]]

269

270

=== 5.2.1 Download and install LoRaWAN packet forwarder ===

271

272

Enable SPI and I2C first:

273

274

a)SPI needs to be enabled on the Raspberry Pi

275

276

Run (% style="background-color:#dcdcdc" %)**sudo raspi-config**(%%) to open the config window

277

278

[[image:1651745476754-240.png||height="234" width="629"]]

279

280

[[image:image-20220505181135-1.png]]

281

282

[[image:image-20220505181135-2.png||height="229" width="622"]]

283

284

In RPI, Fist: Enter the root account:

285

286

(((

287

[[image:1651745583363-614.png||height="151" width="732"]]

)))

and then run:

(% style="background-color:#dcdcdc" %)wget [[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh>>url:https://www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh]]

293

294

(% style="background-color:#dcdcdc" %)chmod +x ./auto_install.sh

295

296

(% style="background-color:#dcdcdc" %)./auto_install.sh

297

298

(((

299

[[image:1651745611629-818.png||height="225" width="729"]]

300

)))

301

302

This will download the packet forwarder package from Dragino Server to RPI, and start install the package.

303

304

You can get these output:

305

306

(((

307

[[image:1651745657252-173.png||height="426" width="621"]]

308

)))

309

310

=== 5.2.2 Config Gateway ID, Frequency Band and Server address ===

311

312

(((

313

After installation, user can find the configuration file in** (% style="color:#0000ff" %)/etc/lora/ (%%)**Replace the gateway ID we got above to the (% style="color:#0000ff" %)**gateway_ID** (%%)in file (% style="color:#0000ff" %)**local_conf.json.**

)))

(((

The default LoRaWAN server points to localhost, user need to put the correct server address to the server_address field in file (% style="color:#0000ff" %)**local_conf.json**(%%), like below.

318

)))

319

320

[[image:1651745709709-887.png||height="820" width="621"]]

321

322

User can find the TTN v3 server address from:

323

324

[[Server Addresses ~| The Things Stack for LoRaWAN (thethingsindustries.com)>>url:https://www.thethingsindustries.com/docs/getting-started/server-addresses/#deployments]]

325

326

And the default frequency band is US915 in (% style="color:#0000ff" %)**global_conf.json**(%%) file.

327

328

[[image:1651745838008-820.png||height="650" width="621"]]

329

330

* If user want to change to other frequency bands, User can copy the file from(% style="color:#0000ff" %)** /etc/lora/cfg-302**(%%) ** **and put it into** (% style="color:#0000ff" %)/etc/lora/global_conf.json(%%).**

331

332

1).Chose your need the name of region frequency.

333

334

[[image:1651745867516-322.png||height="83" width="740"]]

335

336

2). Use this command to copy it.

337

338

cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json

339

340

[[image:1651745984006-868.png||height="87" width="745"]]

341

342

* If user wants to change to other LoRaWAN server, modify the (% style="color:#0000ff" %)**global_conf.json**(%%) file.

=== 5.2.3 Check result ===

348

349

(((

350

Run below command to restart the dragino_fwd:

)))

(((

(% class="box infomessage" %)

355

(((

356

sudo systemctl stop draginofwd

357

)))

358

359

(% class="box infomessage" %)

360

(((

361

sudo systemctl start draginofwd

)))

)))

(((

debug check the ruing status of fwd:

)))

(((

(% class="box infomessage" %)

371

(((

372

sudo systemctl status draginofwd

)))

)))

[[image:1651746045057-414.png||height="193" width="729"]]

377

378

The dragino_fwd will start with the new gateway ID and TTN v3 should show the connection ok:

379

380

[[image:1651746078253-168.png||height="372" width="621"]]

381

382

383

We can check dragino_fwd running states in RPi by running:

384

385

(% class="box infomessage" %)

386

(((

387

sudo journalctl -u draginofwd -f

388

)))

389

390

[[image:1651746111963-838.png||height="184" width="730"]]

391

392

If there are LoRaWAN nodes transmitting nearby, we can see the traffic in **TTN v3 –> Gateway ~-~-> Live data**

393

394

[[image:1651746139304-966.png||height="326" width="621"]]

395

396

397

=== 5.2.4 Commands to handle service ===

398

399

* (% style="color:#0000ff" %)**Stop** (%%)dragino_fwd service: sudo systemctl stop draginofwd

400

* (% style="color:#0000ff" %)**Disable**(%%) dragino_fwd auto run after boot: sudo systemctl disable draginofwd

401

* (% style="color:#0000ff" %)**Start** (%%)dragino_fwd : sudo systemctl start draginofwd

402

* (% style="color:#0000ff" %)**Auto run**(%%) dragino_fwd after boot: sudo systemctl enable draginofwd

403

* (% style="color:#0000ff" %)**Show status** (%%)of dragino_fwd: sudo systemctl status draginofwd

= 6. Order Info =

Part Number: (% style="color:#0000ff" %)**PG1302-XX** (%%) Or Part Number: (% style="color:#0000ff" %)**PG1302-PI-XX **(%%)(Include RPi converter board for RPI 3/4)

411

412

**~ (% style="color:#0000ff" %)XX:(%%)**

413

414

* (% style="color:#0000ff" %)**868** (%%)(For Bands: EU868,IN865)

415

* (% style="color:#0000ff" %)**915** (%%)(For Bands: US915,AU915,AS923,KR920)

416

* (% style="color:#0000ff" %)**470** (%%)(For Band: CN470)

417

418