Last modified by Kilight Cao on 2024/06/22 10:43
<
From version < 98.10 >
edited by Xiaoling
on 2022/05/07 13:53
To version < 98.4 >
edited by Xiaoling
on 2022/05/07 11:42
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -121,6 +121,7 @@
121 121  This example is an example to show how to set up the PG1302 + RPi as a LoRaWAN gateway to use with [[TheThingsNetwork>>url:http://www.thethingsnetwork.org/]](TTN) LoRaWAN server. Set up method for other server are similar.
122 122  )))
123 123  
124 +(% style="text-align:center" %)
124 124  [[image:1651743698677-436.png||height="457" width="686"]]
125 125  
126 126  
... ... @@ -127,8 +127,9 @@
127 127  
128 128  ==== 2.2 Hardware Installation ====
129 129  
130 -**Important Notice: **Please power the RPI with 5V,3A cable.
131 +**~ Important Notice: **Please power the RPI with 5V,3A cable.
131 131  
133 +(% style="text-align:center" %)
132 132  [[image:1651743803032-803.png]]
133 133  
134 134  
... ... @@ -157,6 +157,7 @@
157 157  
158 158   Flash the image to SD card:
159 159  
162 +(% style="text-align:center" %)
160 160  [[image:1651744119133-233.png||height="373" width="621"]]
161 161  
162 162   Note: Download the flash tool following this link
... ... @@ -168,8 +168,14 @@
168 168  
169 169  Connect the RPI Ethernet port to your router, RPi will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the RPI. You can use this IP to connect the WEB UI or SSH access of RPI.
170 170  
171 -Make sure your PC and the RPI is in the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it. Below are screenshots
172 172  
175 +Make sure your PC and the RPI is in the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it.
176 +
177 +Below are screenshots
178 +
179 +
180 +
181 +(% style="text-align:center" %)
173 173  [[image:1651744193675-591.png||height="450" width="466"]]
174 174  
175 175  
... ... @@ -187,6 +187,7 @@
187 187  
188 188   After log in, you will be in the Linux console and type command here.
189 189  
199 +(% style="text-align:center" %)
190 190  [[image:1651744358515-107.png||height="366" width="581"]]
191 191  
192 192  
... ... @@ -195,7 +195,7 @@
195 195  ===== 4.4.1 Home page =====
196 196  
197 197  (((
198 -Open a browser on the PC and type the RPI ip address
208 + Open a browser on the PC and type the RPI ip address
199 199  )))
200 200  
201 201  (((
... ... @@ -203,11 +203,11 @@
203 203  )))
204 204  
205 205  (((
206 -You will see the login interface of RPI as shown below.
216 + You will see the login interface of RPI as shown below.
207 207  )))
208 208  
209 209  (((
210 -The account details for Web Login are:
220 + The account details for Web Login are:
211 211  )))
212 212  
213 213  (((
... ... @@ -218,6 +218,7 @@
218 218  **~ Password:   dragino**
219 219  )))
220 220  
231 +(% style="text-align:center" %)
221 221  [[image:1651744457761-993.png||height="352" width="621"]]
222 222  
223 223  
... ... @@ -224,24 +224,29 @@
224 224  ===== 4.4.2 LoRa Page =====
225 225  
226 226  (((
227 -This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customize the band* as well.
238 + This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN
228 228  )))
229 229  
241 +(((
242 + protocol, and user can customize the band* as well.
243 +)))
244 +
245 +(% style="text-align:center" %)
230 230  [[image:1651744554845-970.png||height="328" width="621"]]
231 231  
232 -Different PG1302 hardware version can support different frequency range:
248 + Different PG1302 hardware version can support different frequency range:
233 233  
234 -➢ 868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
250 + ➢ 868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
235 235  
236 -➢ 915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
252 + ➢ 915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
237 237  
238 -After user choose the frequency plan, he can see the actually frequency in used by checking the
254 + After user choose the frequency plan, he can see the actually frequency in used by checking the
239 239  
240 -page LogRead ~-~-> LoRa Log
256 + page LogRead ~-~-> LoRa Log
241 241  
242 -Note *: See this instruction for how to customize frequency band
258 + Note *: See this instruction for how to customize frequency band
243 243  
244 -[[http:~~/~~/wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway>>url:http://wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway]]
260 + [[http:~~/~~/wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway>>url:http://wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway]]
245 245  
246 246  
247 247  ===== 4.4.3 LoRaWAN Page =====
... ... @@ -248,6 +248,8 @@
248 248  
249 249  ====== 4.4.3.1 Semtech UDP ======
250 250  
267 +
268 +(% style="text-align:center" %)
251 251  [[image:1651744767914-283.png||height="352" width="621"]]
252 252  
253 253   Note *: See this instruction for how to configure TTN.
... ... @@ -257,11 +257,12 @@
257 257  
258 258  ====== 4.4.3.2 Basic Station ======
259 259  
278 +(% style="text-align:center" %)
260 260  [[image:1651744890629-683.png||height="380" width="621"]]
261 261  
262 -Note *: See this instruction for how to configure TTN.
281 + Note *: See this instruction for how to configure TTN.
263 263  
264 -[[https:~~/~~/wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core>>url:https://wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core]]
283 + [[https:~~/~~/wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core>>url:https://wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core]]
265 265  
266 266  
267 267  ===== 4.4.4 LogRead =====
... ... @@ -268,22 +268,26 @@
268 268  
269 269  ====== 4.4.4.1 LoRa Log ======
270 270  
290 +(% style="text-align:center" %)
271 271  [[image:1651744955955-452.png||height="571" width="621"]]
272 272  
273 -Show the frequency for LoRa Radio and traffics.
293 + Show the frequency for LoRa Radio and traffics.
274 274  
275 275  
276 276  ====== 4.4.4.2 System Log ======
277 277  
278 -Show system log.
298 + Show system log.
279 279  
300 +(% style="text-align:center" %)
280 280  [[image:1651745003470-264.png||height="477" width="621"]]
281 281  
282 282  
304 +
283 283  ====== 4.4.4.3 Record Log ======
284 284  
285 -**Record the system log.**
307 +**~ Record the system log.**
286 286  
309 +(% style="text-align:center" %)
287 287  [[image:1651745069814-662.png||height="144" width="621"]]
288 288  
289 289  
... ... @@ -291,7 +291,7 @@
291 291  
292 292  ==== 5.1 OS requirement ====
293 293  
294 -RPI in this example is RPI model 4B with fresh Raspbian OS install.
317 + RPI in this example is RPI model 4B with fresh Raspbian OS install.
295 295  
296 296   pi@raspberrypi:~~$ cat /etc/os-release
297 297  
... ... @@ -316,58 +316,79 @@
316 316  
317 317  ==== 5.2 Get Gateway ID in Raspberry and input this in TTN v3. ====
318 318  
319 -In RPI, run below command to get a Gateway ID
342 + In RPI, run below command to get a Gateway ID
320 320  
321 321   (% class="mark" %)ifconfig eth0
322 322  
346 +(% style="text-align:center" %)
323 323  [[image:1651745210205-512.png||height="130" width="621"]]
324 324  
325 325  (((
326 -We got the ether (eth0 MAC) address is b8:27:eb:49:62:bc). Add ffff at the end and remove “:” to get the gateway ID: b827ebxxxxbcffff.  Input this to TTN v3. Make sure to select legacy packet forwarder.
350 + We got the ether (eth0 MAC) address is b8:27:eb:49:62:bc). Add ffff at the end and remove “:” to get the
327 327  )))
328 328  
353 +(((
354 + gateway ID: b827ebxxxxbcffff.  Input this to TTN v3. Make sure to select legacy packet forwarder.
355 +)))
356 +
357 +(% style="text-align:center" %)
329 329  [[image:1651745267862-321.png||height="526" width="621"]]
330 330  
360 +
361 +
362 +(% style="text-align:center" %)
331 331  [[image:1651745306744-481.png||height="478" width="621"]]
332 332  
333 333  After set up, the status should show not connected as below:
334 334  
367 +(% style="text-align:center" %)
335 335  [[image:1651745366987-458.png||height="363" width="621"]]
336 336  
337 337  
338 338  ===== 5.2.1 Download and install LoRaWAN packet forwarder =====
339 339  
340 -Enable SPI and I2C first:
373 + Enable SPI and I2C first:
341 341  
342 -a)SPI needs to be enabled on the Raspberry Pi
375 + a)SPI needs to be enabled on the Raspberry Pi
343 343  
344 -Run sudo raspi-config to open the config window
377 + Run sudo raspi-config to open the config window
345 345  
379 +(% style="text-align:center" %)
346 346  [[image:1651745476754-240.png||height="235" width="631"]]
347 347  
382 +
383 +(% style="text-align:center" %)
348 348  [[image:image-20220505181135-1.png]]
349 349  
386 +(% style="text-align:center" %)
350 350  [[image:image-20220505181135-2.png]]
351 351  
352 -In RPI , Fist: Enter root account:
353 353  
390 +
391 +
392 + In RPI , Fist: Enter root account:
393 +
394 +(% style="text-align:center" %)
354 354  [[image:1651745583363-614.png]]
355 355  
356 356  
357 -and then run:
398 + and then run:
358 358  
359 -wget [[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh>>url:https://www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh]]
400 + wget [[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh>>url:https://www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh]]
360 360  
361 -chmod +x ./auto_install.sh
402 + chmod +x ./auto_install.sh
362 362  
363 -./auto_install.sh
404 + ./auto_install.sh
364 364  
406 +(% style="text-align:center" %)
365 365  [[image:1651745611629-818.png]]
366 366  
367 -This will download the packet forwarder package from Dragino Server to RPI, and start install the package.
368 368  
369 -You can get these output:
410 + This will download the packet forwarder package from Dragino Server to RPI, and start install the package.
370 370  
412 + You can get these output:
413 +
414 +(% style="text-align:center" %)
371 371  [[image:1651745657252-173.png||height="426" width="621"]]
372 372  
373 373  
... ... @@ -374,36 +374,52 @@
374 374  ===== 5.2.2 Config Gateway ID, Frequency Band and Server address =====
375 375  
376 376  (((
377 -After installation, user can find the configuration file in** /etc/lora/ **Replace the gateway ID we got above to the **gateway_ID** in file **local_conf.json.**
421 + After installation, user can find the configuration file in** /etc/lora/ **Replace the gateway ID we got above to the
378 378  )))
379 379  
380 380  (((
381 -The default LoRaWAN server points to localhost, user need to put the correct server address to the server_address field in file **local_conf.json**, like below.
425 +**~ gateway_ID** in file **local_conf.json**
382 382  )))
383 383  
428 +(((
429 + The default LoRaWAN server points to localhost, user need to put the correct server address to the
430 +)))
431 +
432 +(((
433 + server_address field in file **local_conf.json**, like below.
434 +)))
435 +
436 +(% style="text-align:center" %)
384 384  [[image:1651745709709-887.png||height="820" width="621"]]
385 385  
386 -User can find the TTN v3 server address from:
387 387  
388 -[[Server Addresses ~| The Things Stack for LoRaWAN (thethingsindustries.com)>>url:https://www.thethingsindustries.com/docs/getting-started/server-addresses/#deployments]]
440 + User can find the TTN v3 server address from:
389 389  
442 + [[Server Addresses ~| The Things Stack for LoRaWAN (thethingsindustries.com)>>url:https://www.thethingsindustries.com/docs/getting-started/server-addresses/#deployments]]
390 390  
391 -And the default frequency band is US915 in **global_conf.json** file.
392 392  
445 + And the default frequency band is US915 in **global_conf.json** file.
446 +
447 +(% style="text-align:center" %)
393 393  [[image:1651745838008-820.png||height="650" width="621"]]
394 394  
450 +
395 395  * If user want to change to other frequency bands, User can copy the file from **/etc/lora/cfg-302 **and put it into** /etc/lora/global_conf.json.**
396 396  
397 - 1).Chose your need the name of region frequency.
453 + 1).Chose your need the name of region frequency.
398 398  
455 +(% style="text-align:center" %)
399 399  [[image:1651745867516-322.png]]
400 400  
458 +
401 401   2). Use this command to copy it.
402 402  
403 403   cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json
404 404  
463 +(% style="text-align:center" %)
405 405  [[image:1651745984006-868.png]]
406 406  
466 +
407 407  * If user wants to change to other LoRaWAN server, modify the **global_conf.json** file.
408 408  
409 409  (% class="wikigeneratedid" %)
... ... @@ -414,36 +414,32 @@
414 414  ===== 5.2.3 Check result =====
415 415  
416 416  (((
417 -Run below command to restart the dragino_fwd:
477 + Run below command to restart the dragino_fwd:
418 418  )))
419 419  
420 420  (((
421 -(% class="box infomessage" %)
422 -(((
423 -sudo systemctl stop draginofwd
481 + sudo systemctl stop draginofwd
424 424  )))
425 425  
426 -(% class="box infomessage" %)
427 427  (((
428 -sudo systemctl start draginofwd
485 + sudo systemctl start draginofwd
429 429  )))
430 -)))
431 431  
432 432  (((
433 -debug check the ruing status of fwd:
489 + debug check the ruing status of fwd:
434 434  )))
435 435  
436 436  (((
437 -(% class="box infomessage" %)
438 -(((
439 -sudo systemctl status draginofwd
493 + sudo systemctl status draginofwd
440 440  )))
441 -)))
442 442  
496 +(% style="text-align:center" %)
443 443  [[image:1651746045057-414.png]]
444 444  
445 -The dragino_fwd will start with the new gateway ID and TTN v3 should show the connection ok:
446 446  
500 + The dragino_fwd will start with the new gateway ID and TTN v3 should show the connection ok:
501 +
502 +(% style="text-align:center" %)
447 447  [[image:1651746078253-168.png||height="372" width="621"]]
448 448  
449 449  
... ... @@ -472,7 +472,7 @@
472 472  
473 473  === 6. Order Info ===
474 474  
475 -Part Number: **PG1302-XX**  Or  Part Number: **PG1302-PI-XX   **(Include RPi converter board for RPI 3/4)
531 + Part Number: **PG1302-XX**  Or  Part Number: **PG1302-PI-XX   **(Include RPi converter board for RPI 3/4)
476 476  
477 477  **~ XX:**
478 478  
... ... @@ -483,19 +483,18 @@
483 483  === 7. Packing Info ===
484 484  
485 485  (((
486 -**PG1302 Package Includes**:
542 +**~ PG1302 Package Includes**:
487 487  )))
488 488  
489 -(((
490 -* PG1302 x 1
545 +* (((
546 +PG1302 x 1
491 491  )))
492 -
493 -(((
494 -* LoRa Antenna x 1
548 +* (((
549 +LoRa Antenna x 1
495 495  )))
496 496  
497 497  (((
498 -**PG1302-PI Package Includes**:
553 +**~ PG1302-PI Package Includes**:
499 499  )))
500 500  
501 501  * (((

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0