Last modified by Kilight Cao on 2024/06/22 10:43
<
From version < 121.1 >
edited by Xiaoye
on 2023/03/29 19:54
To version < 110.1 >
edited by Xiaoye
on 2022/09/28 18:13
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -14,11 +14,12 @@
14 14  
15 15  )))
16 16  
17 -= 1. Introduction =
17 += **1. Introduction** =
18 18  
19 -== 1.1 What is PG1302 LoRaWAN Concentrator? ==
20 20  
20 +== **1.1 What is PG1302 LoRaWAN Concentrator?** ==
21 21  
22 +
22 22  (((
23 23  The PG1302 is a (% style="color:green" %)**multi-channel high-performance transmitter/receiver**(%%) designed to simultaneously receive several LoRa packets using random spreading factors on random channels. Its goal is to enable robust connection between a central wireless data concentrator and a massive amount of wireless end-points spread over a very wide range of distances.
24 24  )))
... ... @@ -32,33 +32,38 @@
32 32  )))
33 33  
34 34  
35 -== 1.2 Features ==
36 36  
37 +== **1.2 Features** ==
37 37  
39 +
38 38  * Base on Semtech SX1302 solution
39 -* Support Raspberry Pi 3B/3B+/4, TinkerBoard2/2S, Orange Pi Pc/PC PLUS.
41 +* Support Raspberry Pi 3B/3B+/4
40 40  * Up to -140dBm sensitivity
41 41  * Support 3.3v and 5v.
42 42  * Mini-PCIe Interface
43 43  * Converter board to support Raspberry Pi
44 44  
45 -== 1.3 General Interfaces for PG1302 ==
46 46  
47 47  
49 +== **1.3 General Interfaces for PG1302** ==
50 +
51 +
48 48  * SPI interface for LoRa
49 49  * Power Input: 5v, 1A
50 50  * 1 x I-PEX for LoRa
51 -* Working Temperature: -40 ℃ ~~ 80℃
52 52  
53 -== 1.4 Pin Mapping ==
54 54  
55 55  
58 +== **1.4 Pin Mapping** ==
59 +
60 +
56 56   [[image:1651743282627-547.png||height="402" width="425"]]
57 57  
58 58  
59 -== 1.5 LEDs ==
60 60  
65 +== **1.5 LEDs** ==
61 61  
67 +
62 62  (((
63 63  TX: Blink when transmit a packet
64 64  RX: Blink when receive a packet
... ... @@ -66,17 +66,19 @@
66 66  )))
67 67  
68 68  
69 -== 1.6 Power Consumption ==
70 70  
76 +== **1.6 Power Consumption** ==
71 71  
78 +
72 72  <300mA @ 3.3v.
73 73  
74 74  Detail Test Report see [[this link>>https://www.dropbox.com/sh/89virm4y0b02c7i/AAA-cgQEsSc8gNGFYAB0qZ_Za?dl=0]]
75 75  
76 76  
77 -== 1.7 Applications ==
78 78  
85 +== **1.7 Applications** ==
79 79  
87 +
80 80  * Smart Buildings & Home Automation
81 81  * Logistics and Supply Chain Management
82 82  * Smart Metering
... ... @@ -84,11 +84,14 @@
84 84  * Smart Cities
85 85  * Smart Factory
86 86  
87 -= 2. Example: Set up as LoRaWAN gateway =
88 88  
89 -== 2.1 System structure ==
90 90  
97 += **2. Example: Set up as LoRaWAN gateway** =
91 91  
99 +
100 +== **2.1 System structure** ==
101 +
102 +
92 92  (((
93 93  This example is an example to show how to set up the PG1302 + RPi as a LoRaWAN gateway to use with [[TheThingsNetwork>>url:http://www.thethingsnetwork.org/]](TTN) LoRaWAN server. Set up method for other server are similar.
94 94  
... ... @@ -98,43 +98,41 @@
98 98  [[image:1651743698677-436.png||height="457" width="686"]]
99 99  
100 100  
101 -== 2.2 Hardware Installation ==
102 102  
113 +== **2.2 Hardware Installation** ==
103 103  
115 +
104 104  (% style="color:red" %)**Important Notice: Please power the RPI with 5V,3A cable.**
105 105  
106 106  [[image:image-20220621104746-1.png||height="381" width="451"]]
107 107  
108 108  
109 -= 3. Install the software? =
110 110  
122 += **3. Install the software?** =
111 111  
112 -**Raspberry Pi 3B/3B+/4,**
113 113  
125 +There are two ways to install the software in RPi4 to use PG1302.
126 +
114 114  * Flash SD card with Dragino pre-build image which supports Web UI.
115 -* Install [[Dragino-FWD>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/PG1302/#H5.2.2.A0Selecttheappropriatedeviceversiontodownload:]] in existing RPi OS.
128 +* Install Lora packet forwarder in existing RPi OS.
116 116  
117 -**TinkerBoard2/2S, **
118 118  
119 -* Install [[Dragino-FWD>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/PG1302/#H5.2.2.A0Selecttheappropriatedeviceversiontodownload:]] in the existing OS.
120 120  
121 -**Orange Pi PC/PC PLUS.**
132 += **4. Flash with pre-build image** =
122 122  
123 -* Install [[Dragino-FWD>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/PG1302/#H5.2.2.A0Selecttheappropriatedeviceversiontodownload:]] in the existing OS.
124 124  
125 -= 4. Flash with pre-build image =
135 +== **4.1 Download the dragino image for RPI** ==
126 126  
127 -== 4.1 Download the dragino image for RPI ==
128 128  
129 -
130 130  (((
131 131  Download PG1302_for_Rpi4_64_with_webui from: [[https:~~/~~/www.dropbox.com/sh/f6nbldh1qbspya5/AACgL6pDkwdBQO1BQqq_Nubwa?dl=0>>https://www.dropbox.com/sh/f6nbldh1qbspya5/AACgL6pDkwdBQO1BQqq_Nubwa?dl=0]]
132 132  )))
133 133  
134 134  
135 -== 4.2 Flash the image to an SD card ==
136 136  
144 +== **4.2 Flash the image to an SD card** ==
137 137  
146 +
138 138  Flash the image to the SD card:
139 139  
140 140  [[image:1651744119133-233.png||height="373" width="621"]]
... ... @@ -143,9 +143,10 @@
143 143  (% style="color:red" %)**Note: Download the flash tool following this link：**[[https:~~/~~/www.balena.io/etcher/>>https://www.balena.io/etcher/]]
144 144  
145 145  
146 -== 4.3 Access the Linux console ==
147 147  
156 +== **4.3 Access the Linux console** ==
148 148  
158 +
149 149  (((
150 150  Connect the RPI Ethernet port to your router, RPi will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the RPI. You can use this IP to connect the WEB UI or SSH access of RPI. Make sure your PC and the RPI is in the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it. Below are screenshots
151 151  )))
... ... @@ -182,11 +182,13 @@
182 182  [[image:1651744358515-107.png||height="366" width="581"]]
183 183  
184 184  
185 -== 4.4 Access the WebUI of RPi4 ==
186 186  
187 -=== 4.4.1 Home page ===
196 +== **4.4 Access the WebUI of RPi4** ==
188 188  
189 189  
199 +=== **4.4.1 Home page** ===
200 +
201 +
190 190  (((
191 191  Open a browser on the PC and type the RPI ip address **http:~/~/IP_ADDRESS ** (If the IP is assigned by the uplink router)
192 192  You will see the login interface of RPI as shown below.
... ... @@ -203,9 +203,10 @@
203 203  [[image:1651744457761-993.png||height="352" width="621"]]
204 204  
205 205  
206 -=== 4.4.2 LoRa Page ===
207 207  
219 +=== **4.4.2 LoRa Page** ===
208 208  
221 +
209 209  This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customize the band* as well.
210 210  
211 211  
... ... @@ -222,11 +222,13 @@
222 222  (% style="color:red" %)**Note *: [[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
223 223  
224 224  
225 -=== 4.4.3 LoRaWAN Page ===
226 226  
227 -==== 4.4.3.1 Semtech UDP ====
239 +=== **4.4.3 LoRaWAN Page** ===
228 228  
229 229  
242 +==== **4.4.3.1 Semtech UDP** ====
243 +
244 +
230 230  [[image:1651744767914-283.png||height="352" width="621"]]
231 231  
232 232  
... ... @@ -233,9 +233,10 @@
233 233  (% style="color:red" %)**Note *: [[See this instruction for how to configure TTN>>doc:Main.Notes for TTN.WebHome]].**
234 234  
235 235  
236 -==== 4.4.3.2 Basic Station ====
237 237  
252 +==== **4.4.3.2 Basic Station** ====
238 238  
254 +
239 239  [[image:1651744890629-683.png||height="380" width="621"]]
240 240  
241 241  
... ... @@ -242,11 +242,13 @@
242 242  (% style="color:red" %)**Note *: [[See this instruction for how to configure AWS-loT-Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**
243 243  
244 244  
245 -=== 4.4.4 LogRead ===
246 246  
247 -==== 4.4.4.1 LoRa Log ====
262 +=== **4.4.4 LogRead** ===
248 248  
249 249  
265 +==== **4.4.4.1 LoRa Log** ====
266 +
267 +
250 250  [[image:1651744955955-452.png||height="571" width="621"]]
251 251  
252 252  
... ... @@ -253,9 +253,10 @@
253 253  Show the frequency for LoRa Radio and traffics.
254 254  
255 255  
256 -==== 4.4.4.2 System Log ====
257 257  
275 +==== **4.4.4.2 System Log** ====
258 258  
277 +
259 259  Show system log.
260 260  
261 261  
... ... @@ -262,9 +262,10 @@
262 262  [[image:1651745003470-264.png||height="477" width="621"]]
263 263  
264 264  
265 -==== 4.4.4.3 Record Log ====
266 266  
285 +==== **4.4.4.3 Record Log** ====
267 267  
287 +
268 268  **Record the system log.**
269 269  
270 270  
... ... @@ -271,39 +271,13 @@
271 271  [[image:1651745069814-662.png||height="144" width="621"]]
272 272  
273 273  
274 -= 5. Install stand-alone LoRa Packet Forwarder =
275 275  
276 -== 5.1 Choose the right installation package for your OS ==
295 += **5. Install stand-alone LoRa Packet Forwarder** =
277 277  
278 278  
279 -(((
280 -**draginofwd-32bit (RPI, Orange PI)**
298 +== **5.1 OS requirement** ==
281 281  
282 -**Download URL:** https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-32bit.deb
283 283  
284 -**Linux Command:** wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-32bit.deb && dpkg -i draginofwd-32bit.deb
285 -
286 -
287 -**dragino-64bit (RPI, Orange PI)**
288 -
289 -**Download URL: **https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-64bit.deb
290 -)))
291 -
292 -**Linux Command: **wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-64bit.deb && dpkg -i draginofwd-64bit.deb
293 -
294 -
295 -**dragino-tiker-32bit (Tinker Board)**
296 -
297 -**Download URL: **https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-tinker-32bit.deb
298 -
299 -**Linux Command: **wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-tinker-32bit.deb && dpkg -i draginofwd-tinker-32bit.deb
300 -
301 -
302 -**Install details:**
303 -
304 -[[image:image-20220928181226-1.png||height="218" width="1100"]]
305 -
306 -
307 307  RPI in this example is RPI model 4B with fresh Raspbian OS install.
308 308  
309 309  (% class="box" %)
... ... @@ -323,25 +323,10 @@
323 323  )))
324 324  
325 325  
326 -== 5.2 Select the mode of connection to the server ==
327 327  
321 +== **5.2 Get Gateway ID in Raspberry and input this in TTN v3** ==
328 328  
329 -The Dragino LoRa Packet Forware supports the Semtech UDP and Basic Station mode.
330 330  
331 -The User can choose one of the methods as the connection mode.
332 -
333 -
334 -**~1. Semtech UDP Mode  ~-~-> 5.2.1**
335 -
336 -**2. Basic Station Mode  ~-~-> 5.2.2**
337 -
338 -
339 -=== 5.2.1 Semtech UDP Mode ===
340 -
341 -
342 -==== a). Get a gateway EUI from the device ETH MAC. ====
343 -
344 -
345 345  In RPI, run the below command to get a Gateway ID
346 346  
347 347  (% class="box infomessage" %)
... ... @@ -356,9 +356,7 @@
356 356  (((
357 357  We got the ether (eth0 MAC) address is b8:27:eb:49:62:bc). Add ffff at the end and remove “:” to get the gateway ID: b827ebxxxxbcffff.  Input this to TTN v3. Make sure to select legacy packet forwarder.
358 358  
359 -
360 -
361 -==== b). Input this Gateway EUI to the TTN-Stack ====
338 +
362 362  )))
363 363  )))
364 364  
... ... @@ -367,29 +367,30 @@
367 367  [[image:1651745306744-481.png||height="478" width="621"]]
368 368  
369 369  
370 -==== c). After Register, the status should show not connected as below: ====
347 +After set up, the status should show not connected as below:
371 371  
372 372  [[image:1651745366987-458.png||height="363" width="621"]]
373 373  
374 374  
375 -==== d). Enable SPI and I2C on your device ====
376 376  
377 -**the below example is using Raspberry 4B.**
353 +=== **5.2.1 Download and install LoRaWAN packet forwarder** ===
378 378  
379 379  
356 +Enable SPI and I2C first:
357 +
358 +a)  SPI needs to be enabled on the Raspberry Pi
359 +
380 380  Run (% style="background-color:yellow" %) **sudo raspi-config**(%%) to open the config window
381 381  
382 382  [[image:1651745476754-240.png||height="234" width="629"]]
383 383  
384 -
385 385  [[image:image-20220505181135-1.png]]
386 386  
387 -
388 388  [[image:image-20220505181135-2.png||height="229" width="622"]]
389 389  
390 390  
391 391  
392 -==== e). Access the root account: ====
370 +In RPI, Fist: Enter the root account:
393 393  
394 394  (((
395 395  [[image:1651745583363-614.png||height="151" width="732"]]
... ... @@ -397,59 +397,69 @@
397 397  
398 398  )))
399 399  
400 -==== f). Modify the configuration of FWD ====
401 401  
379 +Select the appropriate device version to download
402 402  
381 +
403 403  (((
404 -After installation, user can find the configuration file in** (% style="color:#0000ff" %)/etc/lora/ (%%)**Replace the gateway ID we got above to the (% style="color:#0000ff" %)**gateway_ID** (%%)in file (% style="color:#0000ff" %)**local_conf.json.**
383 +draginofwd-32bit
384 +
385 +wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-32bit.deb && dpkg -i draginofwd-32bit.deb
386 +
387 +
388 +dragino-64bit
405 405  )))
406 406  
407 -(((
408 -The default LoRaWAN server points to localhost, user need to put the correct server address to the server_address field in file (% style="color:#0000ff" %)**local_conf.json**(%%), like below.
391 +wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-64bit.deb && dpkg -i draginofwd-64bit.deb
409 409  
410 410  
411 -the User can find the lora configuration directory in (% style="color:#0000ff" %)**/etc/lora/**(%%) there are the cfg-302 directory and the global_conf.json, and local_conf.json files.
394 +dragino-tiker-32bit
412 412  
413 -/etc/lora/
414 -├── cfg-302  ~-~--> global configuration file
415 -├── devskey  ~-~--> Database
416 -├── global_conf.json  ~-~--> Frequency plan for current applications
417 -└── local_conf.json  ~-~--> Local fwd configuration
396 +wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-tinker-32bit.deb && dpkg -i draginofwd-tinker-32bit.deb
418 418  
419 -At default, the users need to change two configurations file: global_conf.json and local_conf.json.
420 420  
421 -===== **1.) Configure gateway EUI and server address, port for fwd** =====
399 +(((
400 +
422 422  
402 +[[image:image-20220928181226-1.png]]
403 +
423 423  
424 424  )))
425 425  
426 -[[image:1651745709709-887.png||height="820" width="621"]]
407 +=== **5.2.2 Config Gateway ID, Frequency Band and Server address** ===
427 427  
428 428  
429 -**Note: Users can find the TTN v3 server address from [[Server Addresses ~| The Things Stack for LoRaWAN (thethingsindustries.com)>>url:https://www.thethingsindustries.com/docs/getting-started/server-addresses/#deployments]]**
410 +(((
411 +After installation, user can find the configuration file in** (% style="color:#0000ff" %)/etc/lora/ (%%)**Replace the gateway ID we got above to the (% style="color:#0000ff" %)**gateway_ID** (%%)in file (% style="color:#0000ff" %)**local_conf.json.**
412 +)))
430 430  
414 +(((
415 +The default LoRaWAN server points to localhost, user need to put the correct server address to the server_address field in file (% style="color:#0000ff" %)**local_conf.json**(%%), like below.
431 431  
432 -===== **2). Override the global_conf.json file by selecting the appropriate frequency plan for your region in cfg-302** =====
417 +
418 +)))
433 433  
420 +[[image:1651745709709-887.png||height="820" width="621"]]
434 434  
435 -the default frequency band is US915 in the (% style="color:#0000ff" %)**global_conf.json**(%%) file.
436 436  
437 -[[image:1651745838008-820.png||height="650" width="621"]]
423 +User can find the TTN v3 server address from: [[Server Addresses ~| The Things Stack for LoRaWAN (thethingsindustries.com)>>url:https://www.thethingsindustries.com/docs/getting-started/server-addresses/#deployments]]
438 438  
425 +And the default frequency band is US915 in (% style="color:#0000ff" %)**global_conf.json**(%%) file.
439 439  
440 -If the user wants to change to other frequency bands, the User can copy the file from(% style="color:#0000ff" %)** /etc/lora/cfg-302**(%%) ** **and put it into** (% style="color:#0000ff" %)/etc/lora/global_conf.json(%%).**
427 +[[image:1651745838008-820.png||height="650" width="621"]]
441 441  
442 -**//eg: cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json //**
443 443  
430 +* If user want to change to other frequency bands, User can copy the file from(% style="color:#0000ff" %)** /etc/lora/cfg-302**(%%) ** **and put it into** (% style="color:#0000ff" %)/etc/lora/global_conf.json(%%).**
444 444  
432 +**~ 1). Chose your need the name of region frequency.**
445 445  
446 -====== **Selecting the appropriate frequency plan for your region in cfg-302.** ======
447 447  
448 448  [[image:1651745867516-322.png||height="83" width="740"]]
449 449  
450 450  
451 -====== **Override the global_conf.json** ======
452 452  
439 +**~ 2). Use this command to copy it.**
440 +
453 453  (% class="box infomessage" %)
454 454  (((
455 455  **cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json**
... ... @@ -458,20 +458,30 @@
458 458  [[image:1651745984006-868.png||height="87" width="745"]]
459 459  
460 460  
461 -==== (% style="color:inherit; font-family:inherit; font-size:23px" %)g). Running the Fwd Server(%%) ====
449 +* If user wants to change to other LoRaWAN server, modify the (% style="color:#0000ff" %)**global_conf.json**(%%) file.
462 462  
463 463  
452 +
453 +=== **5.2.3 Check result** ===
454 +
455 +
464 464  (((
465 -Run the below command to restart the dragino_fwd:
457 +Run below command to restart the dragino_fwd:
466 466  )))
467 467  
468 468  (((
469 469  (% class="box infomessage" %)
470 470  (((
463 +**sudo systemctl stop draginofwd**
464 +)))
465 +
466 +(% class="box infomessage" %)
467 +(((
471 471  **sudo systemctl start draginofwd**
472 472  )))
473 473  )))
474 474  
472 +
475 475  (((
476 476  debug check the ruing status of fwd:
477 477  )))
... ... @@ -486,13 +486,15 @@
486 486  [[image:1651746045057-414.png||height="193" width="729"]]
487 487  
488 488  
489 -Wait for a few minutes, the gateway will be online/active on the TTN-Stack.
490 490  
488 +The dragino_fwd will start with the new gateway ID and TTN v3 should show the connection ok:
489 +
490 +
491 491  [[image:1651746078253-168.png||height="372" width="621"]]
492 492  
493 493  
494 494  
495 -Get the draginofwd real-time running log:
495 +We can check dragino_fwd running states in RPi by running:
496 496  
497 497  (% class="box infomessage" %)
498 498  (((
... ... @@ -508,8 +508,10 @@
508 508  [[image:1651746139304-966.png||height="326" width="621"]]
509 509  
510 510  
511 -==== h). Commands to handle service ====
512 512  
512 +=== **5.2.4 Commands to handle service** ===
513 +
514 +
513 513  * (% style="color:#0000ff" %)**Stop** (%%)dragino_fwd service:  sudo systemctl stop draginofwd
514 514  * (% style="color:#0000ff" %)**Disable**(%%) dragino_fwd auto run after boot: sudo systemctl disable draginofwd
515 515  * (% style="color:#0000ff" %)**Start** (%%)dragino_fwd : sudo systemctl start draginofwd
... ... @@ -517,59 +517,10 @@
517 517  * (% style="color:#0000ff" %)**Show status** (%%)of dragino_fwd:  sudo systemctl status draginofwd
518 518  
519 519  
520 -=== **5.2.2 Basic Station Mode.** ===
521 521  
523 += **6. Order Info** =
522 522  
523 -==== a). Get a gateway EUI from the device ETH MAC. ====
524 524  
525 -
526 -In RPI, run the below command to get a Gateway ID
527 -
528 -(% class="box infomessage" %)
529 -(((
530 -**~ ifconfig eth0**
531 -)))
532 -
533 -[[image:1651745210205-512.png||height="130" width="621"]]
534 -
535 -
536 -(((
537 -(((
538 -We got the ether (eth0 MAC) address is b8:27:eb:49:62:bc). Add ffff at the end and remove “:” to get the gateway ID: b827ebxxxxbcffff.  Input this to TTN v3. Make sure to select legacy packet forwarder.
539 -)))
540 -)))
541 -
542 -
543 -
544 -
545 -b
546 -
547 -
548 -
549 -
550 -c
551 -
552 -d
553 -
554 -e
555 -
556 -f
557 -
558 -g
559 -
560 -h
561 -
562 -i
563 -
564 -j
565 -
566 -k
567 -
568 -
569 -
570 -= 6. Order Info =
571 -
572 -
573 573  Part Number: (% style="color:#0000ff" %)**PG1302-XX**   (%%) Or  Part Number: (% style="color:#0000ff" %)**PG1302-PI-XX   **(%%)(Include RPi converter board for RPI 3/4)
574 574  
575 575  **~ (% style="color:#0000ff" %)XX:(%%)**
... ... @@ -578,8 +578,10 @@
578 578  * (% style="color:red" %)**915** (%%)(For Bands: US915,AU915,AS923,KR920)
579 579  * (% style="color:red" %)**470** (%%)(For Band: CN470)
580 580  
581 -= 7. Packing Info =
582 582  
535 +
536 += **7. Packing Info** =
537 +
583 583  (((
584 584  
585 585  
... ... @@ -596,6 +596,7 @@
596 596  (((
597 597  
598 598  
554 +
599 599  **PG1302-PI Package Includes**:
600 600  )))
601 601  
... ... @@ -604,13 +604,16 @@
604 604  * RPi3/4 converter PCB
605 605  * Screws to hole converter PCB on RPI.
606 606  
563 +
607 607  **PG1302-PI Dimension and weight: **
608 608  
609 609  * Device Size: 18 x 8 x 4 cm
610 610  * Weight: 150g
611 611  
569 +
570 +
612 612  (((
613 -= 8. Support =
572 += **8. Support** =
614 614  
615 615  
616 616  (((
image-20230329164417-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -46.4 KB
Content
image-20230329164704-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -16.6 KB
Content
image-20230329165619-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -106.9 KB
Content
image-20230329195416-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -9.3 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0