Changes for page PG1302 -- LoRaWAN Concentrator User Manual

Last modified by Kilight Cao on 2024/06/22 10:43

From version < 110.2 >

edited by Xiaoling
on 2022/12/21 09:40

To version < 108.10 >

edited by Xiaoling
on 2022/07/28 14:38

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 1 removed)
- image-20220928181226-1.png

Details

Page properties

Content

@@ -14,9 +14,9 @@
  )))
--= 1. Introduction =
++= **1. Introduction** =
--== 1.1  What is PG1302 LoRaWAN Concentrator? ==
++== **1.1  What is PG1302 LoRaWAN Concentrator?** ==
  (((
@@ -32,9 +32,10 @@
  )))
--== 1.2 Features ==
++== **1.2 Features** ==
++
  * Base on Semtech SX1302 solution
  * Support Raspberry Pi 3B/3B+/4
  * Up to -140dBm sensitivity
@@ -44,17 +44,16 @@
--== 1.3 General Interfaces for PG1302 ==
++== **1.3 General Interfaces for PG1302** ==
  * SPI interface for LoRa
  * Power Input: 5v, 1A
  * 1 x I-PEX for LoRa
--* Working Temperature: -40 ℃ ~~ 65℃
--== 1.4 Pin Mapping ==
++== **1.4 Pin Mapping** ==
       [[image:1651743282627-547.png||height="402" width="425"]]
@@ -61,27 +61,27 @@
--== 1.5 LEDs ==
++== **1.5 LEDs** ==
--(((
  TX: Blink when transmit a packet
  RX: Blink when receive a packet
  Config: Always ON
--)))
--== 1.6 Power Consumption ==
++== **1.6 Power Consumption** ==
++
  <300mA @ 3.3v.
  Detail Test Report see [[this link>>https://www.dropbox.com/sh/89virm4y0b02c7i/AAA-cgQEsSc8gNGFYAB0qZ_Za?dl=0]]
--== 1.7 Applications ==
++== **1.7 Applications** ==
++
  * Smart Buildings & Home Automation
  * Logistics and Supply Chain Management
  * Smart Metering
@@ -91,15 +91,13 @@
--= 2. Example: Set up as LoRaWAN gateway =
++= **2. Example: Set up as LoRaWAN gateway.** =
--== 2.1 System structure ==
++== **2.1 System structure** ==
  (((
  This example is an example to show how to set up the PG1302 + RPi as a LoRaWAN gateway to use with [[TheThingsNetwork>>url:http://www.thethingsnetwork.org/]](TTN) LoRaWAN server. Set up method for other server are similar.
--
--
  )))
  [[image:1651743698677-436.png||height="457" width="686"]]
@@ -106,7 +106,7 @@
--== 2.2 Hardware Installation ==
++== **2.2 Hardware Installation** ==
  (% style="color:red" %)**Important Notice: Please power the RPI with 5V,3A cable.**
@@ -115,9 +115,8 @@
--= 3. Install the software? =
++= **3. Install the software?** =
--
  There are two ways to install the software in RPi4 to use PG1302.
  * Flash SD card with Dragino pre-build image which supports Web UI.
@@ -125,9 +125,9 @@
--= 4. Flash with pre-build image =
++= **4. Flash with pre-build image** =
--== 4.1 Download the dragino image for RPI ==
++== **4.1 Download the dragino image for RPI** ==
  (((
@@ -135,9 +135,10 @@
  )))
--== 4.2 Flash the image to an SD card ==
++== **4.2 Flash the image to an SD card** ==
++
  Flash the image to the SD card:
  [[image:1651744119133-233.png||height="373" width="621"]]
@@ -146,12 +146,11 @@
  (% style="color:red" %)**Note: Download the flash tool following this link：**[[https:~~/~~/www.balena.io/etcher/>>https://www.balena.io/etcher/]]
--== 4.3 Access the Linux console ==
++== **4.3 Access the Linux console** ==
--(((
++
  Connect the RPI Ethernet port to your router,  RPi will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the RPI. You can use this IP to connect the WEB UI or SSH access of RPI. Make sure your PC and the RPI is in the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it. Below are screenshots
--)))
  [[image:1651744193675-591.png||height="450" width="466"]]
@@ -185,16 +185,15 @@
  [[image:1651744358515-107.png||height="366" width="581"]]
--== 4.4 Access the WebUI of RPi4 ==
--=== 4.4.1 Home page ===
++== **4.4 Access the WebUI of RPi4.** ==
++=== **4.4.1 Home page** ===
--(((
--Open a browser on the PC and type the RPI ip address **http:~/~/IP_ADDRESS ** (If the IP is assigned by the uplink router)
++
++Open a browser on the PC and type the RPI ip address [[http:~~/~~/IP_ADDRESS** **>>url:http://192.168.1.xx/]] (If the IP is assigned by the uplink router)
  You will see the login interface of RPI as shown below.
  The account details for Web Login are:
--)))
  (((
  **~                   (% style="color:#0000ff" %)User Name: root(%%)**
@@ -206,39 +206,40 @@
  [[image:1651744457761-993.png||height="352" width="621"]]
--=== 4.4.2 LoRa Page ===
++=== **4.4.2 LoRa Page** ===
++
  This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customize the band* as well.
--
  [[image:1651744554845-970.png||height="328" width="621"]]
--
  Different PG1302 hardware version can support different frequency range:
--* (% style="color:red" %)**868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.**
--* (% style="color:red" %)**915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920**
++➢** (% style="color:red" %)868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.(%%)**
++➢ (% style="color:red" %)**915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920**
++
  After user choose the frequency plan, he can see the actually frequency in used by checking the (% style="color:#037691" %)**page LogRead ~-~-> LoRa Log**
  (% style="color:red" %)**Note *: [[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
--=== 4.4.3 LoRaWAN Page ===
--==== 4.4.3.1 Semtech UDP ====
++=== **4.4.3 LoRaWAN Page** ===
++==== **4.4.3.1 Semtech UDP** ====
++
  [[image:1651744767914-283.png||height="352" width="621"]]
--
  (% style="color:red" %)**Note *: [[See this instruction for how to configure TTN>>doc:Main.Notes for TTN.WebHome]].**
--==== 4.4.3.2 Basic Station ====
++==== **4.4.3.2 Basic Station** ====
++
  [[image:1651744890629-683.png||height="380" width="621"]]
@@ -245,45 +245,46 @@
  (% style="color:red" %)**Note *: [[See this instruction for how to configure AWS-loT-Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**
--=== 4.4.4 LogRead ===
--==== 4.4.4.1 LoRa Log ====
++=== **4.4.4 LogRead** ===
++==== **4.4.4.1 LoRa Log** ====
++
  [[image:1651744955955-452.png||height="571" width="621"]]
--
  Show the frequency for LoRa Radio and traffics.
--==== 4.4.4.2 System Log ====
++==== **4.4.4.2 System Log** ====
++
  Show system log.
--
  [[image:1651745003470-264.png||height="477" width="621"]]
--==== 4.4.4.3 Record Log ====
++==== **4.4.4.3 Record Log** ====
++
  **Record the system log.**
--
  [[image:1651745069814-662.png||height="144" width="621"]]
--= 5. Install stand-alone LoRa Packet Forwarder =
--== 5.1 OS requirement ==
++= **5. Install stand-alone LoRa Packet Forwarder.** =
++== **5.1 OS requirement** ==
++
  RPI in this example is RPI model 4B with fresh Raspbian OS install.
  (% class="box" %)
  (((
--        pi@raspberrypi:~~$ cat /etc/os-release
++       pi@raspberrypi:~~$ cat /etc/os-release
          PRETTY_NAME="Raspbian GNU/Linux 8 (jessie)"
          NAME="Raspbian GNU/Linux"
          VERSION_ID="8"
@@ -298,9 +298,10 @@
  )))
--== 5.2 Get Gateway ID in Raspberry and input this in TTN v3 ==
++== **5.2 Get Gateway ID in Raspberry and input this in TTN v3** ==
++
  In RPI, run the below command to get a Gateway ID
  (% class="box infomessage" %)
@@ -329,9 +329,10 @@
  [[image:1651745366987-458.png||height="363" width="621"]]
--=== 5.2.1 Download and install LoRaWAN packet forwarder ===
++=== **5.2.1 Download and install LoRaWAN packet forwarder** ===
++
  Enable SPI and I2C first:
  a)  SPI needs to be enabled on the Raspberry Pi
@@ -340,10 +340,8 @@
  [[image:1651745476754-240.png||height="234" width="629"]]
--
  [[image:image-20220505181135-1.png]]
--
  [[image:image-20220505181135-2.png||height="229" width="622"]]
@@ -356,36 +356,30 @@
  )))
++and then run:
--**Select the appropriate device version to download:**
++(% style="background-color:#dcdcdc" %)wget [[https:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh>>url:https://www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/auto_install.sh]]
++(% style="background-color:#dcdcdc" %)chmod +x ./auto_install.sh
--(((
--**draginofwd-32bit**
++(% style="background-color:#dcdcdc" %)./auto_install.sh
--wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-32bit.deb && dpkg -i draginofwd-32bit.deb
--
--
--**dragino-64bit**
++(((
++[[image:1651745611629-818.png||height="225" width="729"]]
  )))
--wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-64bit.deb && dpkg -i draginofwd-64bit.deb
++This will download the packet forwarder package from Dragino Server to RPI, and start install the package.
++You can get these output:
--**dragino-tiker-32bit**
--
--wget https:~/~/www.dragino.com/downloads/downloads/LoRa_Gateway/PG1302/software/draginofwd-tinker-32bit.deb && dpkg -i draginofwd-tinker-32bit.deb
--
--
  (((
--
++[[image:1651745657252-173.png||height="426" width="621"]]
--[[image:image-20220928181226-1.png||height="218" width="1100"]]
  )))
--=== 5.2.2 Config Gateway ID, Frequency Band and Server address ===
++=== **5.2.2 Config Gateway ID, Frequency Band and Server address** ===
  (((
@@ -412,28 +412,21 @@
  **~     1). Chose your need the name of region frequency.**
--
  [[image:1651745867516-322.png||height="83" width="740"]]
++*
++**   2). Use this command to copy it.
--**~  2). Use this command to copy it.**
++     cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json
--(% class="box infomessage" %)
--(((
--**cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json**
--)))
--
  [[image:1651745984006-868.png||height="87" width="745"]]
--
  * If user wants to change to other LoRaWAN server, modify the (% style="color:#0000ff" %)**global_conf.json**(%%) file.
++=== **5.2.3 Check result** ===
--=== 5.2.3 Check result ===
--
--
  (((
  Run below command to restart the dragino_fwd:
  )))
@@ -483,15 +483,15 @@
  [[image:1651746111963-838.png||height="184" width="730"]]
--
   If there are LoRaWAN nodes transmitting nearby, we can see the traffic in (% style="color:#037691" %)**TTN v3 –> Gateway ~-~-> Live data**
  [[image:1651746139304-966.png||height="326" width="621"]]
--=== 5.2.4 Commands to handle service ===
++=== **5.2.4 Commands to handle service** ===
++
  * (% style="color:#0000ff" %)**Stop** (%%)dragino_fwd service:  sudo systemctl stop draginofwd
  * (% style="color:#0000ff" %)**Disable**(%%) dragino_fwd auto run after boot: sudo systemctl disable draginofwd
  * (% style="color:#0000ff" %)**Start** (%%)dragino_fwd :  sudo systemctl start draginofwd
@@ -499,10 +499,9 @@
  * (% style="color:#0000ff" %)**Show status** (%%)of dragino_fwd:  sudo systemctl status draginofwd
++= **6. Order Info** =
--= 6. Order Info =
--
  Part Number:  (% style="color:#0000ff" %)**PG1302-XX**   (%%) Or  Part Number:  (% style="color:#0000ff" %)**PG1302-PI-XX   **(%%)(Include RPi converter board for RPI 3/4)
  **~     (% style="color:#0000ff" %)XX:(%%)**
@@ -513,7 +513,7 @@
--= 7. Packing Info =
++= **7. Packing Info** =
  (((
@@ -531,6 +531,7 @@
  (((
++
  **PG1302-PI Package Includes**:
  )))
@@ -539,7 +539,6 @@
  * RPi3/4 converter PCB
  * Screws to hole converter PCB on RPI.
--
  **PG1302-PI Dimension and weight: **
  * Device Size: 18 x 8 x 4 cm
@@ -548,7 +548,7 @@
  (((
--= 8. Support =
++= **8. Support** =
  (((
@@ -561,8 +561,5 @@
  (((
  With your question as detail as possible. We will reply and help you in the shortest.
--
--
--
  )))
  )))

image-20220928181226-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoye

Size

...	...	@@ -1,1 +1,0 @@
1		-29.1 KB

Content

Changes for page PG1302 -- LoRaWAN Concentrator User Manual

Summary

Details

Applications

Navigation