Summary

• Page properties (2 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • image-20220928181226-1.png

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.Xiaoling
	1	+XWiki.Xiaoye

Content

...	...	@@ -16,6 +16,7 @@
16	16
17	17	= **1. Introduction** =
18	18
	19	+
19	19	== **1.1 What is PG1302 LoRaWAN Concentrator?** ==
20	20
21	21
...	...	@@ -45,6 +45,7 @@
45	45
46	46
47	47
	49	+
48	48	== **1.3 General Interfaces for PG1302** ==
49	49
50	50
...	...	@@ -54,6 +54,7 @@
54	54
55	55
56	56
	59	+
57	57	== **1.4 Pin Mapping** ==
58	58
59	59
...	...	@@ -64,9 +64,11 @@
64	64	== **1.5 LEDs** ==
65	65
66	66
	70	+(((
67	67	TX: Blink when transmit a packet
68	68	RX: Blink when receive a packet
69	69	Config: Always ON
	74	+)))
70	70
71	71
72	72
...	...	@@ -91,13 +91,17 @@
91	91
92	92
93	93
94		-= **2. Example: Set up as LoRaWAN gateway.** =
95	95
	100	+= **2. Example: Set up as LoRaWAN gateway** =
	101	+
	102	+
96	96	== **2.1 System structure** ==
97	97
98	98
99	99	(((
100	100	This example is an example to show how to set up the PG1302 + RPi as a LoRaWAN gateway to use with [[TheThingsNetwork>>url:http://www.thethingsnetwork.org/]](TTN) LoRaWAN server. Set up method for other server are similar.
	108	+
	109	+
101	101	)))
102	102
103	103	[[image:1651743698677-436.png||height="457" width="686"]]
...	...	@@ -115,6 +115,7 @@
115	115
116	116	= **3. Install the software?** =
117	117
	127	+
118	118	There are two ways to install the software in RPi4 to use PG1302.
119	119
120	120	* Flash SD card with Dragino pre-build image which supports Web UI.
...	...	@@ -122,8 +122,10 @@
122	122
123	123
124	124
	135	+
125	125	= **4. Flash with pre-build image** =
126	126
	138	+
127	127	== **4.1 Download the dragino image for RPI** ==
128	128
129	129
...	...	@@ -148,7 +148,9 @@
148	148	== **4.3 Access the Linux console** ==
149	149
150	150
	163	+(((
151	151	Connect the RPI Ethernet port to your router, RPi will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the RPI. You can use this IP to connect the WEB UI or SSH access of RPI. Make sure your PC and the RPI is in the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]]) to access it. Below are screenshots
	165	+)))
152	152
153	153
154	154	[[image:1651744193675-591.png||height="450" width="466"]]
...	...	@@ -183,14 +183,17 @@
183	183
184	184
185	185
186		-== **4.4 Access the WebUI of RPi4.** ==
	200	+== **4.4 Access the WebUI of RPi4** ==
187	187
	202	+
188	188	=== **4.4.1 Home page** ===
189	189
190	190
191		-Open a browser on the PC and type the RPI ip address [[http:~~/~~/IP_ADDRESS** **>>url:http://192.168.1.xx/]] (If the IP is assigned by the uplink router)
	206	+(((
	207	+Open a browser on the PC and type the RPI ip address **http:~/~/IP_ADDRESS ** (If the IP is assigned by the uplink router)
192	192	You will see the login interface of RPI as shown below.
193	193	The account details for Web Login are:
	210	+)))
194	194
195	195	(((
196	196	**~ (% style="color:#0000ff" %)User Name: root(%%)**
...	...	@@ -208,13 +208,15 @@
208	208
209	209	This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customize the band* as well.
210	210
	228	+
211	211	[[image:1651744554845-970.png||height="328" width="621"]]
212	212
	231	+
213	213	Different PG1302 hardware version can support different frequency range:
214	214
215		-➢** (% style="color:red" %)868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.(%%)**
	234	+* (% style="color:red" %)**868: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.**
	235	+* (% style="color:red" %)**915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920**
216	216
217		-➢ (% style="color:red" %)**915: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920**
218	218
219	219	After user choose the frequency plan, he can see the actually frequency in used by checking the (% style="color:#037691" %)**page LogRead ~-~-> LoRa Log**
220	220
...	...	@@ -224,11 +224,13 @@
224	224
225	225	=== **4.4.3 LoRaWAN Page** ===
226	226
	246	+
227	227	==== **4.4.3.1 Semtech UDP** ====
228	228
229	229
230	230	[[image:1651744767914-283.png||height="352" width="621"]]
231	231
	252	+
232	232	(% style="color:red" %)**Note *: [[See this instruction for how to configure TTN>>doc:Main.Notes for TTN.WebHome]].**
233	233
234	234
...	...	@@ -245,11 +245,13 @@
245	245
246	246	=== **4.4.4 LogRead** ===
247	247
	269	+
248	248	==== **4.4.4.1 LoRa Log** ====
249	249
250	250
251	251	[[image:1651744955955-452.png||height="571" width="621"]]
252	252
	275	+
253	253	Show the frequency for LoRa Radio and traffics.
254	254
255	255
...	...	@@ -259,6 +259,7 @@
259	259
260	260	Show system log.
261	261
	285	+
262	262	[[image:1651745003470-264.png||height="477" width="621"]]
263	263
264	264
...	...	@@ -268,12 +268,14 @@
268	268
269	269	**Record the system log.**
270	270
	295	+
271	271	[[image:1651745069814-662.png||height="144" width="621"]]
272	272
273	273
274	274
275		-= **5. Install stand-alone LoRa Packet Forwarder.** =
	300	+= **5. Install stand-alone LoRa Packet Forwarder** =
276	276
	302	+
277	277	== **5.1 OS requirement** ==
278	278
279	279
...	...	@@ -281,7 +281,7 @@
281	281
282	282	(% class="box" %)
283	283	(((
284		- pi@raspberrypi:~~$ cat /etc/os-release
	310	+ pi@raspberrypi:~~$ cat /etc/os-release
285	285	PRETTY_NAME="Raspbian GNU/Linux 8 (jessie)"
286	286	NAME="Raspbian GNU/Linux"
287	287	VERSION_ID="8"
...	...	@@ -368,6 +368,7 @@
368	368
369	369	This will download the packet forwarder package from Dragino Server to RPI, and start install the package.
370	370
	397	+
371	371	You can get these output:
372	372
373	373	(((
...	...	@@ -404,18 +404,26 @@
404	404
405	405	**~ 1). Chose your need the name of region frequency.**
406	406
	434	+
407	407	[[image:1651745867516-322.png||height="83" width="740"]]
408	408
409	409
410		-*
411		-** 2). Use this command to copy it.
412	412
413		- cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json
	439	+**~ 2). Use this command to copy it.**
414	414
	441	+(% class="box infomessage" %)
	442	+(((
	443	+**cp /etc/lora/cfg-302/EU-global_conf.json /etc/lora/global_conf.json**
	444	+)))
	445	+
415	415	[[image:1651745984006-868.png||height="87" width="745"]]
416	416
	448	+
417	417	* If user wants to change to other LoRaWAN server, modify the (% style="color:#0000ff" %)**global_conf.json**(%%) file.
418	418
	451	+
	452	+
	453	+
419	419	=== **5.2.3 Check result** ===
420	420
421	421
...	...	@@ -468,6 +468,7 @@
468	468	[[image:1651746111963-838.png||height="184" width="730"]]
469	469
470	470
	506	+
471	471	If there are LoRaWAN nodes transmitting nearby, we can see the traffic in (% style="color:#037691" %)**TTN v3 –> Gateway ~-~-> Live data**
472	472
473	473	[[image:1651746139304-966.png||height="326" width="621"]]
...	...	@@ -484,6 +484,8 @@
484	484	* (% style="color:#0000ff" %)**Show status** (%%)of dragino_fwd:  sudo systemctl status draginofwd
485	485
486	486
	523	+
	524	+
487	487	= **6. Order Info** =
488	488
489	489
...	...	@@ -497,6 +497,7 @@
497	497
498	498
499	499
	538	+
500	500	= **7. Packing Info** =
501	501
502	502	(((
...	...	@@ -524,6 +524,8 @@
524	524	* RPi3/4 converter PCB
525	525	* Screws to hole converter PCB on RPI.
526	526
	566	+
	567	+
527	527	**PG1302-PI Dimension and weight: **
528	528
529	529	* Device Size: 18 x 8 x 4 cm
...	...	@@ -531,6 +531,7 @@
531	531
532	532
533	533
	575	+
534	534	(((
535	535	= **8. Support** =
536	536
...	...	@@ -545,5 +545,8 @@
545	545
546	546	(((
547	547	With your question as detail as possible. We will reply and help you in the shortest.
	590	+
	591	+
	592	+
548	548	)))
549	549	)))

image-20220928181226-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoye

Size

...	...	@@ -1,0 +1,1 @@
	1	+29.1 KB

Content