Changes for page LPS8N -- LoRaWAN Gateway User Manual

Last modified by Xiaoling on 2025/06/12 17:51

From 75.1 to 75.2 From 159.1 to 160.1

From version 75.2

edited by Xiaoling
on 2022/05/13 18:06

Change comment: There is no comment for this version

To version 159.1

edited by Xiaoye
on 2022/08/19 15:17

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (3 modified, 0 added, 0 removed)
Attachments (0 modified, 74 added, 0 removed)

Details

Page properties

Title

@@ -1,1 +1,1 @@
--DLOS8N
++LPS8N - LoRaWAN Gateway User Manual

Author

@@ -1,1 +1,1 @@
--XWiki.Xiaoling
++XWiki.Xiaoye

Content

@@ -1,13 +3,9 @@
--
--
  (% style="text-align:center" %)
--[[image:1652409757234-446.png||height="399" width="399"]]
++[[image:1656917428377-954.png||height="475" width="475"]]
--**DLOS8N Outdoor LoRaWAN Gateway User Manual**
--
  **Table of Contents：**
  {{toc/}}
@@ -15,55 +15,67 @@
--= 1. Introduction =
--== 1.1 What is the DLOS8N ==
++
++
++
++
++
++
++(% style="color:inherit; font-family:inherit; font-size:29px" %)1.  Introduction
++
++== 1.1  What is the LPS8N ==
++
++
++
  (((
--The DLOS8N is an (% style="color:#4f81bd" %)open source outdoor LoRaWAN Gateway. (% style="color:black" %)It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.
++The LPS8N is an (% style="color:#4f81bd" %)**open source LoRaWAN Indoor Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular network. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.
  )))
  (((
--DLOS8N supports (% style="color:#4f81bd" %)Semtech packet forwarder (% style="color:black" %)and (% style="color:#4f81bd" %)LoRaWAN Station connection, (% style="color:black" %)it is fully compatible with LoRaWAN protocol. DLOS8N includes a (% style="color:#4f81bd" %)SX1302 LoRaWAN concentrator.
++The LPS8N uses (% style="color:#4f81bd" %)**Semtech packet forwarder**(%%) & (% style="color:#4f81bd" %)**LoRaWAN Station connection**(%%) and fully compatible with LoRaWAN protocol. It includes a (% style="color:#4f81bd" %)**SX1302 LoRaWAN concentrator**(%%), which provides 10 programmable parallel demodulation paths.
  )))
  (((
--DLOS8N has (% style="color:#4f81bd" %)pre-configured standard LoRaWAN frequency bands (% style="color:black" %)to use for different countries.User can also customize the frequency bands to use in their own LoRaWAN network.
++LPS8N has (% style="color:#4f81bd" %)**pre-configured standard LoRaWAN frequency bands**(%%) to use for different countries. User can also (% style="color:#4f81bd" %)**customized the frequency bands** (%%)to use in their own LoRa network.
  )))
  (((
--DLOS8N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.
++LPS8N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.
  )))
  (((
--DLOS8N supports (% style="color:#4f81bd" %) auto-provision (% style="color:black" %) for mass deployment and long term maintain. System intergrator can easily change the settings.
++
  )))
--[[image:1652411526195-923.png]]
++[[image:1656918270059-192.png]]
--== 1.2 Specifications ==
++== 1.2  Specifications ==
--**Hardware System:**
++(% style="color:#037691" %)**Hardware System:**
++
++(((
           Linux Part:
++)))
  * 400Mhz ar9331 processor
  * 64MB RAM
  * 16MB Flash
--**Interface:**
++(% style="color:#037691" %)**Interface:**
  * 10M/100M RJ45 Ports x 1
  * WiFi : 802.11 b/g/n
  * LoRaWAN Wireless
--* Power Input: 12 ~~ 24 V DC, 2 A
--* IEEE 802.3 af compliant PoE port (DC 37  ~~ 57 v)
++* Power Input: 5V DC, 2A, Type C
  * USB 2.0 host connector x 1
  * Mini-PCI E connector x 1
  * SX1302 + 2 x SX1250
--**WiFi Spec:**
++(% style="color:#037691" %)**WiFi Spec:**
  * IEEE 802.11 b/g/n
  * Frequency Band: 2.4 ~~ 2.462GHz
@@ -76,9 +76,9 @@
  ** 11g 54M : -71dbm
  ** 11n 20M : -67dbm
--**LoRa Spec:**
++(% style="color:#037691" %)**LoRa Spec:**
--* Up to -140 dBm sensitivity with SX1250 Tx/Rx front-end
++* Up to -140 dBm sensitivity
  * 70 dB CW interferer rejection at 1 MHz offset
  * Able to operate with negative SNR, CCR up to 9dB
  * Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator
@@ -87,130 +87,129 @@
  * Dynamic data-rate (DDR) adaptation
  * True antenna diversity or simultaneous dual-band operation
--**Cellular 4G LTE (optional):**
++(% style="color:#037691" %)**Cellular 4G LTE (optional):**
--* Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
--* Standard Size SIM Slot
--* 2 x 4G Sticker Antenna.
++* Quectel [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
++* Micro SIM Slot
++* External 4G Sticker Antenna.
  * Up to 150Mbps downlink and 50Mbps uplink data rates
  * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
--**Power over Ethernet:**
--* IEEE 802.3af compliant.
--* Support wide input voltage range  37Vdc to 57Vdc.
--* Thermal cut off.
--* Short circuit protection.
--* Over current protection
--* Isolation level 4 KVrms.
--* Enhanced surge protection
--== 1.3 Features ==
++== 1.3  Features ==
--* Open Source Embedded Linux system
--* Managed by Web GUI, SSH via LAN or WiFi
--* Support Semtech UDP packet forwarder
--* Support LoRaWAN Station Connection
--* Cellular Failover conntection(option)
--* Direct Communication to LoRaWAN ABP Node
--* LoRaWAN packet filtering
--* Far seeing LED indicator
--* Built-in GPS module for location & timing
--* External fiber glass antenna
--* Auto-Provision
--* Remote Monitoring
--* 802.3af PoE
--* IP65
--* Lighting Protection
--* Power Consumption:12v ,300-500mA
--== 1.4 Hardware System Structure ==
++* Open Source OpenWrt system
++* Managed by Web GUI, SSH via WAN or WiFi
++* Remote access with Reverse-SSH or remote.it
++* Emulates 49x LoRa demodulators
++* LoRaWAN Gateway
++* 10 programmable parallel demodulation paths
++* Pre-configure to support different LoRaWAN regional settings.
++* Allow to customize LoRaWAN regional parameters.
++* Support Local decode ABP end node info and transfer to MQTT server
++* Support different level log in.
++* Support Semtech Packet Forwarder
++* Support LoRaWAN basic station.
++* Optional 3G/4G cellular connection
--[[image:1652411641871-482.png||height="425" width="732"]]
--== 1.5 DLOS8N Applications ==
++== 1.4  Hardware System Structure ==
--[[image:1652411671209-920.png||height="618" width="650"]]
++[[image:1657079015096-949.png]]
--== 1.6 LED Indicators ==
--[[image:1652411720670-489.png]]
++== 1.5  LPS8N Applications ==
--There is a waterproof triple color LED on DLOS8N enclosure, the meaning of the LED is:
--(((
--(((
--* (((
--(% style="color:green" %)**SOLID GREEN**: (% style="color:black" %)DLOS8N is alive with LoRaWAN server connection.
--)))
--)))
++[[image:1657079055940-721.png]]
--* (((
--(% style="color:green" %)**BLINKING GREEN**:(% style="color:black" %) a) Device has internet connection but no LoRaWAN Connection.  or b) Device is in booting stage, in this stage, it will (% style="color:green" %)**BLINKING GREEN**(% style="color:black" %) for several seconds and then (% style="color:red" %)**RED** (% style="color:black" %)and (% style="color:#ffc000" %)**YELLOW** (% style="color:black" %)will blink together.
--)))
--* (((
--(% style="color:red" %)**SOLID RED**: (% style="color:black" %)Device doesn’t have Internet connection.
--)))
--)))
--== 1.7 WiFi Direction ==
++== 1.6  LED Indicators ==
--DLOS8N use directional WiFi Antenna. The best direction is as below:
--[[image:1652412859663-161.png||height="341" width="333"]]
++LPS8N has totally four LEDs, They are:
++* **Power LED **[[image:image-20220706115518-1.png||height="15" width="16"]] : This (% style="color:red" %)**RED LED**(%%) will be **solid on** if the device is properly powered.
++* **SYS LED    ** [[image:image-20220706115518-3.png||height="16" width="16"]] : This **RGB LED** will shows different colors on different state:
++** (% style="color:blue" %)**SOLID BLUE**(%%): Device is alive with LoRaWAN server connection.
++** (% style="color:blue" %)**BLINKING BLUE**(%%): a) Device has internet connection but no LoRaWAN Connection.  or   b) Device is in booting stage, in this stage, it will (% style="color:blue" %)**BLINKING BLUE**(%%) for several seconds and then with (% style="color:red" %)**SOLID RED**(%%) and (% style="color:blue" %)**BLINKING BLUE**(%%) together
++** (% style="color:red" %)**SOLID RED**(%%): Device doesn't have Internet connection.
--= 2. Access and Configure DLOS8N =
++* **ETH LED    **[[image:image-20220706115518-4.png||height="15" width="17"]] :  This LED shows the ETH interface connection status.
--The DLOS8N is configured as a WiFi Access Point by default. User can access and configure the DLOS8N after connecting to its WiFi network, or via its Ethernet port.
--== 2.1 Find IP address of DLOS8N ==
--=== 2.1.1 Connect via WiFi ===
++= 2.  Access and Configure LPS8N =
--[[image:1652412985720-934.png]]
++(((
++The LPS8N is configured as a WiFi Access Point by factory default. You can access and configure the LPS8N after connecting to its WiFi network, or via its WAN Ethernet port.
++)))
--At the first boot of DLOS8N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(% style="color:black" %)with password:
++
++== 2.1  Find IP address of LPS8N ==
++
++
++=== 2.1.1  Connect via WiFi ===
++
++[[image:1657085974260-168.png]]
++
++
++At the first boot of LPS8N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(% style="color:black" %)with password: (% style="background-color:yellow" %)dragino+dragino
++
  [[image:1652413127647-377.png]]
--(% style="background-color:#ffffcc" %)dragino+dragino
++(((
  User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the DLOS8N has the default IP (% style="color:green" %)10.130.1.1
--=== 2.1.2 Connect via Ethernet with DHCP IP from router ===
++
++)))
--[[image:1652414114583-532.png]]
++=== 2.1.2  Connect via Ethernet with DHCP IP from router ===
++[[image:1657086105922-299.png]]
--Alternatively, connect the DLOS8N Ethernet port to your router and DLOS8N will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the DLOS8N. You can also use this IP to connect.
++(((
++Alternatively, connect the LPS8N Ethernet port to your router and LPS8N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LPS8N. You can also use this IP to connect.
--=== 2.1.3 Connect via WiFi with DHCP IP from router ===
--[[image:1652414137639-956.png]]
++
++)))
++=== 2.1.3  Connect via WiFi with DHCP IP from router ===
--If the DLOS8N already connect to the router via WiFi, use can use the WiFi IP to connect to DLOS8N.
++[[image:1657086192720-649.png]]
--=== 2.1.4 Connect via Ethernet with fall back ip ===
--The WAN port also has a [[fall back ip address>>path:#_I_configured_LPS8]] for access if user doesn’t connect to uplink router. Click [[here>>path:#_I_configured_LPS8]] to see how to configure.
++If the LPS8N already connect to the router via WiFi, use can use the WiFi IP to connect to LPS8N.
--== 2.2 Access Configure Web UI ==
++=== 2.1.4  Connect via Ethernet with fall back ip ===
++
++
++The WAN port also has a [[fall back ip address>>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
++
++
++
++== 2.2  Access Configure Web UI ==
++
++
  **Web Interface**
--Open a browser on the PC and type the DLOS8N ip address (depends on your connect method)
++Open a browser on the PC and type the LPS8N ip address (depends on your connect method)
  [[http:~~/~~/10.130.1.1/>>url:http://10.130.1.1/]]  (Access via WiFi AP network)
@@ -219,7 +219,7 @@
  http:~/~/IP_ADDRESS or [[http:~~/~~/ IP_ADDRESS:8000>>url:http://192.168.1.xx:8000]]
--You will see the login interface of DLOS8N as shown below.
++You will see the login interface of LPS8N as shown below.
  The account details for Web Login are:
@@ -231,269 +231,399 @@
++= 3.  Typical Network Setup =
--= 3. Typical Network Setup =
--== 3.1 Overview ==
++== 3.1  Overview ==
--The DLOS8N supports flexible network set up for different environments. This section describes the typical network topology. The network set up includes:
++The LPS8N supports flexible network set up for different environments. This section describes the typical network topology. The network set up includes:
++
  * **WAN Port Internet Mode**
  * **WiFi Client Mode**
  * **WiFi AP Mode**
--* **Cellular Mode**
--== 3.2 Use WAN port to access Internet ==
--By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N’s WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
--[[image:1652420169255-959.png]]
++== 3.2  Use WAN port to access Internet ==
--== 3.3 Access the Internet as a WiFi Client ==
++By default, the LPS8N is set to use the WAN port to connect to an upstream network. When you connect the LPS8N's WAN port to an upstream router, LPS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
--In the WiFi Client Mode, DLOS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
++[[image:1657088560833-398.png]]
++
++
++
++== 3.3  Access the Internet as a WiFi Client ==
++
++
++In the WiFi Client Mode, LPS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
++
++(((
  The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~->  WiFi WAN Client Settings**
--[[image:1652420327792-211.png]]
++[[image:1657088818095-182.png]]
++)))
++
++(((
  In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click Save & Apply to connect.
--== 3.4 Access the Internet via Cellular ==
++
++)))
--If the DLOS8N support 3G/4G Cellular modem option, When the label on the shell is displayed as Model : DLOS8N-EC25, it indicates that DLOS8 already has EC25 3G/4G modules,user can use it as main internet connection or back up.
++== 3.4  Use built-in 4G modem for internet access ==
--First, release the four screws of DLOS8N, pull out PCB and install SIM card as below:
++(((
++(((
++If the LPS8N has 3G/4G Cellular modem, user can use it as main internet connection or back up.
++)))
--[[image:1652420606018-181.png]]
++(((
++First, install the Micro SIM card as below direction
++)))
--[[image:1652420718132-929.png||height="450" width="766"]]
++(((
++Second, Power off/ ON LPS8N to let it detect the SIM card.
++)))
++)))
--The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**
++[[image:1657090855037-497.png]]
++(((
++
++)))
++(((
++The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**
++)))
++
++(((
  While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
++)))
--[[image:1652421032117-341.png||height="329" width="752"]]
++(((
++[[image:1657090932270-444.png]]
++)))
--(% style="color:red" %)**Note** *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.
--== 3.5 Check Internet connection ==
++== 3.5  Check Internet connection ==
++
  In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.
--* GREEN Tick [[image:1652421151598-130.png||height="23" width="24"]]   : This interface has Internet connection.
--* Yellow Tick  [[image:1652421168047-470.png||height="22" width="21"]]   : This interface has IP address but don’t use it for internet connection.
--* RED Cross   [[image:1652421179500-890.png||height="24" width="27"]]  : This interface doesn’t connected.
++* GREEN Tick  [[image:1652436675869-206.png||height="14" width="15"]]  : This interface has Internet connection.
++* Yellow  Tick  [[image:1652436705761-420.png||height="15" width="15"]]  : This interface has IP address but don't use it for internet connection.
++* RED Cross    [[image:1652436787176-950.png||height="14" width="15"]]  : This interface doesn't connected.
--[[image:1652421351382-793.png||height="339" width="765"]]
++[[image:1657091099235-452.png]]
--= 4. Example: Configure as a LoRaWAN gateway =
--DLOS8N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.
++= 4.  Example: Configure as a LoRaWAN gateway =
--[[image:image-20220513140429-1.png||height="565" width="824"]]
--This chapter describes how to use the DLOS8Nto work with
++LPS8N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.
--[[T>>url:https://www.thethingsnetwork.org/]]heThingsNetwork v3(T[[TN>>url:https://www.thethingsnetwork.org/]] v3[[)>>url:http://)]][[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
++(((
++[[image:1657091257648-882.png]]
++)))
--== 4.1 Create a gateway in TTN V3 Server ==
++(((
++This chapter describes how to use the LPS8N to work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
++)))
--(% style="color:#4f81bd" %)**Step 1: Get a Unique gateway ID.**
--Every DLOS8N has a unique gateway id. The ID can be found at LoRaWAN page:
--[[image:1652421929753-168.png||height="403" width="739"]]
++== 4.1  Create a gateway in TTN V3 Server ==
--The example gateway id is: a840411e96744154
++(% style="color:blue" %)**Step 1: Get a Unique gateway ID.**
--(% style="color:#4f81bd" %)**Step 2: Sign up a user account in TTN server**
++(((
++Every LPS8N has a unique gateway id. The ID can be found at LoRaWAN page:
++)))
++(((
++[[image:1657091583941-544.png]]
++)))
++
++The example gateway id is: (% style="color:green" %)**a840411e96744154**
++
++
++
++(% style="color:blue" %)**Step 2: Sign up a user account in TTN server**
++
  [[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]
--[[image:1652422127479-258.png||height="346" width="738"]]
++[[image:1657091739530-531.png]]
--(% style="color:#4f81bd" %)**Step 3: Choose the TTNv3 Cluster Picker**
--[[image:1652422142236-792.png||height="356" width="737"]]
++(% style="color:blue" %)**Step 3: Choose the TTNv3 Cluster Picker**
++(((
++[[image:1657091719947-297.png]]
++
++)))
++
  (% style="color:red" %)**Note: Choose the cluster corresponds to a specific Gateway server address**
--* Europe 1 (% style="color:red" %)corresponding Gateway server address: (% style="color:black" %)eu1.cloud.thethings.network
--* North America 1 (% style="color:red" %)corresponding Gateway server address:** **(% style="color:black" %)nam1.cloud.thethings.network
--* Australia 1 (% style="color:red" %)corresponding Gateway server address:** **(% style="color:black" %)au1.cloud.thethings.network
--* Legacy V2 Console : (% style="color:red" %)TTN v2 shuts down in December 2021
--(% style="color:#4f81bd" %)**Step 4: Create a Gateway**
++* Europe 1** (% style="color:red" %)corresponding Gateway server address:(%%)**(% style="color:red" %) (% style="color:black" %)eu1.cloud.thethings.network
++* North America 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)nam1.cloud.thethings.network
++* Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network
++* Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**
--[[image:1652422440891-514.png||height="360" width="747"]]
++(% style="color:blue" %)**Step 4: Create a Gateway**
++
++[[image:1657091941182-367.png]]
++
  Click the Gateway icon and then click Add gateway.
++
  Open the following page:
--   [[image:1652422470352-518.png||height="391" width="716"]]
++ [[image:image-20220706155323-5.png||height="579" width="1060"]]
--[[image:1652422479876-297.png||height="398" width="729"]]
--(% style="color:red" %)**Notice: **Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.
++[[image:image-20220706155323-6.png||height="582" width="1066"]]
++
++(((
++(% style="color:red" %)**Notice: Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.**
++
++
++)))
++
  After creating the gateway, you can see the gateway info, as below.
--[[image:1652422509034-682.png||height="299" width="739"]]
++[[image:1657094130908-567.png]](% style="display:none" %)
--== 4.2 Configure DLOS8N to connect to TTN v3 ==
--You can now configure the DLOS8N to let it connect to TTN network V3.
++== 4.2  Configure LPS8N to connect to TTN v3 ==
--Make sure your DLOS8N has a working Internet Connection first.
++(((
++You can now configure the LPS8N to let it connect to TTN network V3.
++)))
++
++(((
++Make sure your LPS8N has a working Internet Connection first.
++)))
++
++(((
  Choose the right server provider and click (% style="color:#4f81bd" %)**Save&Apply**
++)))
--[[image:1652422624783-580.png||height="327" width="729"]]
++[[image:1657094183213-301.png]]
--(% style="color:red" %)**Note: **The server address must match the Gateway server address you choose in TTN V3.
++(% style="color:red" %)**Note: The server address must match the Gateway server address you choose in TTN V3.**
++
++
  In the home page, we can see the LoRaWAN connection is ready now.
--[[image:1652422685063-596.png||height="327" width="729"]]
++[[image:1657094202420-798.png]]
++
  In TTN v3 portal, we can also see the gateway is connected.
--[[image:1652422703020-955.png||height="343" width="730"]]
++[[image:1657094221515-510.png]]
--== 4.3 Configure frequency ==
--We also need to set the frequency plan in DLOS8N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.
++== 4.3  Configure frequency ==
--[[image:1652422737399-529.png||height="362" width="737"]]
++We also need to set the frequency plan in LPS8N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.
++[[image:1657094249818-468.png]]
++
++
  In logread page, user can check the frequency actually used.
-- [[image:1652422763536-750.png||height="514" width="730"]]
++ [[image:1657094333704-207.png]]
--4.4 Add a LoRaWAN End Device
++== 4.4  Add a LoRaWAN End Device ==
++
++
++(((
  This section shows how to add a LoRaWAN End device to a LoRaWAN network and see the data from TTN web site.
++)))
++(((
  We use [[LT-22222-L>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]] IO Controller as a reference device - the setup for other LoRaWAN devices will be similar.
++)))
  [[image:1652422794767-871.png]]
--(% style="color:#4f81bd" %)**Step 1**: (% style="color:black" %)Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.
++(((
++(% style="color:blue" %)**Step 1**: (%%)Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.
++
++)))
++
++(((
  Three codes are required to define the device in TTN v3:
++)))
  * DEV EUI - Unique ID code for a particular device.
  * APP EUI - ID code for an Application defined in TTN v3.
  * APP Key - Unique key to secure communications with a particular device.
++(((
  A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.
++)))
--[[image:1652422840936-838.png]]
++[[image:1657094382177-591.png]]
--(% style="color:red" %)Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands.  Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.
++(((
++(% style="color:red" %)**Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands.  Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.**
++
++)))
++
++(((
  For the TTN v3 server, you can use the codes set in the device as in the following example.
++)))
++(((
  Select **Add Application** to open the screen below.
++)))
--[[image:1652422946999-255.png||height="356" width="744"]]
++[[image:1657094417175-831.png]]
  Open the **Application **select** Add end device**
++
  Start Register the end device
--[[image:1652422975885-591.png||height="359" width="726"]]
++[[image:1657094444802-101.png]]
++(((
  Select OTAA activation mode
++
++)))
++(((
  The LoRaWAN version for your device should be provided by the manufacturer in a datasheet as LoRaWAN version or LoRaWAN specification. The most commonly used LoRaWAN versions are v1.0.2 and v1.0.3.
++)))
--[[image:1652422998005-968.png||height="352" width="744"]]
++[[image:1657094475730-208.png]]
  First, input the End device ID, AppEUI and DevEUI.
--[[image:1652423022781-339.png||height="365" width="741"]]
++[[image:1657094646429-966.png]]
++
  Secondly, choose the corresponding frequency and LoRaWAN class capabilities.
--[[image:1652423046741-467.png||height="355" width="736"]]
++[[image:1657094674045-755.png]]
++
++(((
  Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.
++
++)))
--(% style="color:#4f81bd" %)**Step 2**: (% style="color:black" %)Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.
++(((
++(% style="color:blue" %)**Step 2**:  (%%)Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.
--(% style="color:red" %)Note that it may take some time for the device data to appear in the TTN v3 display.
++
++)))
--[[image:1652423277549-324.png||height="273" width="745"]]
++(((
++(% style="color:red" %)**Note that it may take some time for the device data to appear in the TTN v3 display.**
++
++)))
--= 5. Web Configure Pages =
++[[image:1657094791060-639.png]]
--== 5.1 Home ==
++
++= 5.  Web Configure Pages =
++
++
++== 5.1  Home ==
++
++
  Shows the system running status.
--[[image:1652423418568-752.png||height="329" width="724"]]
++[[image:1657094893942-726.png]]
--== 5.2 LoRa Settings ==
--=== 5.2.1 LoRa ~-~-> LoRa ===
++== 5.2  LoRa Settings ==
++
++=== 5.2.1  LoRa ~-~-> LoRa ===
++
++
++(((
  This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customized the band* as well.
++)))
--Different DLOS8N hardware version can support different frequency range:
++(((
++Different LPS8N hardware version can support different frequency range:
++)))
--* **868**: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
--* **915**: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
++* (% style="color:blue" %)**868**(%%): valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
++* (% style="color:blue" %)**915**(%%): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
--After user choose the frequency plan, he can see the actually frequency in used by checking the page **LogRead ~-~-> LoRa Log**
++(((
++
--[[image:1652423554776-574.png||height="380" width="740"]]
++(((
++After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:green" %)**LogRead ~-~-> LoRa Log**
++)))
++)))
--Note *: See this instruction for how to customize frequency band:
++[[image:1657094930903-357.png]]
--[[http:~~/~~/wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway>>url:http://wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway]]
++(% style="color:red" %)**Note *:** **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
--=== 5.2.2 LoRa ~-~-> ABP Decryption ===
--The DLOS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
++=== 5.2.2  LoRa ~-~-> ABP Decryption ===
++
++The LPS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
++
  * No internet connection.
--* User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>http://8.211.40.43:8080/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]).
++* User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).
--Detail of this feature: [[Communication with ABP End Node>>http://8.211.40.43:8080/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]
++(((
++Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**
++)))
--[[image:1652423628833-467.png||height="357" width="755"]]
++[[image:1657095412271-942.png]]
--== 5.3 LoRaWAN Settings ==
--=== 5.3.1 LoRaWAN ~-~-> LoRaWAN ===
++== 5.3  LoRaWAN Settings ==
++
++=== 5.3.1  LoRaWAN ~-~-> LoRaWAN ===
++
++
  This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc
  [[image:1652423628833-467.png||height="357" width="755"]]
@@ -500,170 +500,220 @@
  (% style="color:red" %)**Note:**
--~*: User can ignore the latitude and longitude settings here, DLOS8N will use the actually value from GPS module.
++~*: User can ignore the latitude and longitude settings here, LPS8N will use the actually value from GPS module.
  ~**: Packet filter is to drop the unwanted LoRaWAN packet, instruction see here:
--See :[[Filter unwanted LoRaWAN packets>>http://8.211.40.43:8080/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]
++**See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**
--=== 5.3.2 LoRaWAN ~-~-> Amazon AWS-IoT ===
++=== 5.3.2  LoRaWAN ~-~-> Amazon AWS-IoT ===
++
++
  [[image:1652428499323-384.png||height="275" width="723"]]
--Please see this instruction to know more detail and demo for how to connect to AWS-IoT LoRaWAN Core: [[http:~~/~~/wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core>>url:http://wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core]]
++(((
++Please see this instruction to know more detail and demo for how to connect to **[[AWS-IoT LoRaWAN Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**
--=== 5.3.3 LoRaWAN ~-~-> LORIOT ===
++
++)))
++
++=== 5.3.3  LoRaWAN ~-~-> LORIOT ===
++
++
++(((
  Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]
++)))
--Instruction: [[http:~~/~~/wiki.dragino.com/index.php?title=Notes_for_LORIOT>>url:http://wiki.dragino.com/index.php?title=Notes_for_LORIOT]]
++(((
++Instruction: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
++)))
  [[image:1652428648903-878.png||height="266" width="731"]]
--== 5.4 MQTT Settings ==
--If end nodes works in ABP mode, user can configure DLOS8N to transfer the data to MQTT broker,
++== 5.4  MQTT Settings ==
--Instruction:
--[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#MQTT_Forward_Instruction>>url:http://wiki.dragino.com/index.php?title=Main_Page#MQTT_Forward_Instruction]]
++(((
++If end nodes works in ABP mode, user can configure LPS8N to transfer the data to MQTT broker,
++)))
++(((
++Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**
++)))
++
++
  [[image:1652428705046-212.png||height="417" width="733"]]
--== 5.5 System ==
--=== 5.5.1 System ~-~-> System Overview ===
++== 5.5  System ==
++
++=== 5.5.1  System ~-~-> System Overview ===
++
++
  Shows the system info:
--[[image:1652428773760-580.png||height="408" width="728"]]
++[[image:1657155158184-134.png]]
--=== 5.5.2 System ~-~-> General ( login settings) ===
--[[image:1652428861256-300.png||height="354" width="724"]]
++=== 5.5.2  System ~-~-> General ( login settings) ===
--**__System Password:__**
--There are two login for DLOS8N: (% style="color:#4f81bd" %)root /dragino (% style="color:black" %)or (% style="color:#4f81bd" %)admin /dragino. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
++[[image:1657155183982-792.png]]
--This page can be used to set the password for them.
  (((
--
++(% style="color:#037691" %)**__System Password:__**
  )))
--**__Timezone:__**
++(((
++There are two login for LPS8N: (% style="color:#4f81bd" %)root /dragino (% style="color:black" %)or (% style="color:#4f81bd" %)admin /dragino. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
++)))
--Set device timezone.
++(((
++This page can be used to set the password for them.
++)))
  (((
--
++(% style="color:#037691" %)**__Timezone:  __**(%%)Set device timezone.
  )))
--**__Port forwarding:__**
++(((
++(% style="color:#037691" %)**__Port forwarding:  __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.
--Enable/Disable the HTTP and SSH access via WAN interface.
++
++)))
--=== 5.5.3 System ~-~-> Network ===
++=== 5.5.3  System ~-~-> Network ===
--[[image:1652429149053-824.png||height="467" width="725"]]
++[[image:1657155288223-566.png]]
--**__LAN Settings:__**
++(((
++(% style="color:#037691" %)**__LAN Settings:    __**(%%)When the LPS8N has the AP enable, LAN settings specify the network info for LPS8N's own network.
++)))
--When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N’s own network.
--
  (((
--
++(% style="color:#037691" %)__**WAN Settings:  **__(%%)Setting for LPS8N WAN port
  )))
--__**WAN Settings:**__
++(((
++(% style="color:#037691" %)__**WiFi Settings:  **__** **(%%)Setting for LPS8N WiFi IP when use it as WiFi Client
--Setting for DLOS8N WAN port
--(((
  )))
--__**WiFi Settings:**__
++=== 5.5.4  System ~-~-> WiFi ===
--Setting for DLOS8N WiFi IP when use it as WiFi Client
++LPS8N WiFi Settings.
--=== 5.5.4 System ~-~-> WiFi ===
++[[image:1657155457089-430.png]]
--DLOS8N WiFi Settings.
--[[image:1652429430767-921.png||height="367" width="723"]]
++=== 5.5.5  System ~-~-> Cellular ===
--=== 5.5.5 System ~-~-> Cellular ===
  While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
--[[image:1652429309615-825.png||height="320" width="732"]]
--(% style="color:red" %)Note *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.
++[[image:1657155507672-204.png]]
--=== 5.5.6 System ~-~-> Network Status ===
++(% style="color:red" %)**Note *: For LPS8N which doesn't have the cellular module, this page will shows Cellular not detected.**
--[[image:1652429486609-208.png||height="415" width="728"]]
--=== 5.5.7 System ~-~-> Remote Mgnt & Auto Provision ===
++=== 5.5.6  System ~-~-> Network Status ===
++
++[[image:1657155554265-721.png]]
++
++
++
++=== 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
++
++
  Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
--[[image:1652429518191-846.png||height="332" width="733"]]
--[[image:1652429527544-247.png||height="327" width="724"]]
++[[image:image-20220707112053-4.png||height="451" width="995"]]
--[[image:1652429537849-154.png||height="339" width="722"]]
++[[image:image-20220707112053-5.png||height="453" width="1004"]]
--Please see this document for detail:
++(% style="display:none" %)
--[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
++(% style="display:none" %) [[image:1657157402578-508.png||height="450" width="992"]]
++(% id="cke_bm_589629S" style="display:none" %) [[image:image-20220707092040-2.png||height="452" width="1002"]]
--R-SSH is for remote access device and management, introduction for how to use:
++[[image:image-20220707092040-3.png||height="449" width="956"]]
--[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#Remote_Access_Gateway_via_Reverse_SSH>>url:http://wiki.dragino.com/index.php?title=Main_Page#Remote_Access_Gateway_via_Reverse_SSH]]
++(((
++Please see this document for detail:  [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
++)))
++
++(% style="display:none" %) (%%)
++
++(((
++R-SSH is for remote access device and management, introduction for how to use: [[Remote Access Gateway>>doc:Main.Monitor & Remote Access Gateway.WebHome]]
++)))
++
  [[image:1652429624400-864.png||height="432" width="716"]]
--=== 5.5.8 System ~-~-> Firmware Upgrade ===
--We keep improving the DLOS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
++=== 5.5.8  System ~-~-> Firmware Upgrade ===
++
++We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
++
  * **Latest firmware**:  [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],
--( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )
++( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LIG16/Firmware]])
  * **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].
--( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )
++( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )
++(((
  The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.
++)))
++(((
  (% style="color:green" %)**Web~-~-> System~-~-> Firmware Upgrade**
++)))
--[[image:1652429711145-862.png||height="270" width="737"]]
++[[image:1657156052651-770.png]]
--Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.
++(((
++Select the required image and click (% style="color:blue" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:blue" %)**Process Update**(%%) to upgrade.
++)))
--(% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
++(((
++(% style="color:red" %)**NOTE**: (%%)You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)**Preserve Settings**(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
++
++
++)))
++
++(((
  The system will automatically boot into the new firmware after upgrade.
++)))
--[[image:1652429962190-224.png||height="358" width="729"]]
++[[image:1657156094153-520.png]]
  (% style="color:red" %)**NOTE***(%%): User can also upgrade firmware via Linux console
@@ -672,66 +672,147 @@
  (% style="color:#4f81bd" %)**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**
++
  (% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
--=== 5.5.9 System ~-~-> Reboot/Reset ===
++=== 5.5.9  System ~-~-> Reboot/Reset ===
++
++
  [[image:1652430197132-330.png||height="256" width="724"]]
  (((
++
++
  )))
--=== 5.5.10 System ~-~-> Package Maintain ===
++=== 5.5.10  System ~-~-> Package Maintain ===
--[[image:1652430243826-126.png||height="289" width="723"]]
++[[image:1657156199070-491.png]]
++
  Place to show what package has installed and possible to upgrade packages.
++
++
++== 5.6  LogRead ==
++
++
++=== 5.6.1  LogRead ~-~-> LoRa Log ===
++
++
++Show the frequency for LoRa Radio and traffics.
++
++[[image:1657156300781-933.png]]
++
++
++
++=== 5.6.2  LogRead ~-~-> System Log ===
++
++
++Show the system log
++
++[[image:1657156341198-226.png]]
++
++
++
++= 6.  More features =
++
++
++== 6.1  Packet Filtering ==
++
++
  (((
--
++Drop unwanted packets.
  )))
--== 5.6 LogRead ==
++(((
++See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]
++)))
--=== 5.6.1 LogRead ~-~-> LoRa Log ===
--[[image:1652430356784-567.png||height="325" width="730"]]
--Show the frequency for LoRa Radio and traffics.
++== 6.2  Remote Access ==
++
  (((
--
++Remote Access Devices for management.
  )))
--=== 5.6.2 LogRead ~-~-> System Log ===
++(((
++Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access>>http://wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access]]
++)))
--Show the system log
--[[image:1652430369760-511.png||height="373" width="730"]]
++== 6.3  How to decode ABP LoRaWAN node ==
--= 6. More features =
--== 6.1 More instructions ==
++(((
++Decode ABP:
++)))
--[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRa.2FLoRaWAN_Gateway_Instruction>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRa.2FLoRaWAN_Gateway_Instruction]]
++(((
++[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20~~-~~--%20LG308/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]
++)))
++
++
++== 6.4  How to set data to MQTT broker ==
++
++
  (((
--
++Only support ABP LoRaWAN End Node
  )))
--= 7. Linux System =
++(((
++Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]
++)))
--The DLOS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.
--== 7.1 SSH Access for Linux console ==
--User can access the Linux console via the SSH protocol. Make sure your PC and the DLOS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.
++== 6.5  More instructions ==
--IP address:  IP address of DLOS8N
++[[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)
++
++
++
++== 6.6  Auto-Provision ==
++
++
++Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
++
++[[image:image-20220707092040-1.png||height="451" width="995"]]
++
++[[image:image-20220707092040-2.png||height="452" width="1002"]]
++
++[[image:image-20220707092040-3.png||height="449" width="956"]](% style="display:none" %)
++
++(((
++Please see this document for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
++)))
++
++(% style="display:none" %)  (%%)
++
++
++= 7.   (% style="display:none" %) (%%)Linux System =
++
++
++The LPS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.
++
++(% style="display:none" %) (%%)
++
++
++== 7.1  SSH Access for Linux console ==
++
++
++User can access the Linux console via the SSH protocol. Make sure your PC and the LPS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.
++
++IP address:  IP address of LPS8N
++
  Port:         22 (via WiFi AP mode) or 2222 (via WAN Interface)
  User Name:      (% style="color:green" %)**root**
@@ -740,49 +740,75 @@
  After logging in, you will be in the Linux console and can enter commands as shown below.
--[[image:1652431588565-830.png]]
--The “(% class="mark" %)**logread -f**(%%)” command can be used to debug how system runs.
++[[image:1657158198733-338.png]]
--[[image:1652431609193-637.png||height="214" width="732"]]
++The “** (% style="background-color:yellow" %)logread -f(%%)**(% style="background-color:yellow" %)” (%%)command can be used to debug how system runs.
--== 7.2 Edit and Transfer files ==
++[[image:1657158190234-805.png]]
--The DLOS8N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.
++
++== 7.2  Edit and Transfer files ==
++
++
++(((
++The LPS8N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.
++)))
++
++(((
  In Windows, one of the easiest methods is using the [[WinSCP>>url:https://winscp.net/eng/index.php]] utility.
++)))
--After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the DLOS8N, or edit the files directly in the windows.
++(((
++After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the LPS8N, or edit the files directly in the windows.
++)))
++(((
  Screenshot is as below:
++)))
  [[image:1652431650755-450.png]]
--== 7.3 File System ==
--The DLOS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.
++== 7.3  File System ==
--The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the DLOS8N flash.
++(((
++The LPS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.
++)))
++
++(((
++The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the LPS8N flash.
++)))
++
++(((
  You can use an external USB flash memory device to extend the size of flash memory for storage.
++)))
--== 7.4 Package maintenance system ==
--DLOS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure DLOS8N to use **//iperf //**.
++== 7.4  Package maintenance system ==
++
++LPS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure LPS8N to use **//iperf //**.
++
++(((
  Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])
++)))
++(((
  **In Linux Console run:**
++)))
  (((
--(% style="color:green" %)**root@dragino-169d30:~~# opkg update**           (% style="color:black" %)~/~/ to get the latest packages list
++(% style="color:green" %)**root@dragino-169d30:~~# opkg update**             (% style="color:black" %)~/~/ to get the latest packages list
  )))
  (((
--(% style="color:green" %)**root@dragino-169d30:~~# opkg list**    (% style="color:black" %)              ~/~/shows the available packages
++(% style="color:green" %)**root@dragino-169d30:~~# opkg list**    (% style="color:black" %)               ~/~/shows the available packages
  )))
  (((
@@ -818,41 +818,120 @@
  (((
  (% style="background-color:#dcdcdc" %)//Configuring iperf.//
++
++
++
  )))
--= 8. Upgrade Linux Firmware =
++= 8.  Upgrade Linux Firmware =
--= 9. FAQ =
++We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
--== 9.1 How can I configure for a customized frequency band? ==
++* **Latest firmware**:  [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],
--See below link for how to customize frequency band:
++( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LIG16/Firmware]])
--[[http:~~/~~/wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway>>url:http://wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway]]
++* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].
++( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )
--== 9.2 Can I connect DLOS8N to LORIOT? ==
--Yes, the set up instruction is here: [[http:~~/~~/wiki.dragino.com/index.php?title=Notes_for_LORIOT>>url:http://wiki.dragino.com/index.php?title=Notes_for_LORIOT]]
++(((
++The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **(%%)is the upgrade Image. There are different methods to upgrade, as below.
++)))
--== 9.3 Can I make my own firmware for the gateway, where can I find the source code? ==
--Yes, You can make your own firmware for the DLOS8N for branding purposes or to add customized applications.
++== 8.1  Upgrade via Web UI ==
++
++(((
++Go to the page: (% style="color:green" %)**Web ~-~-> System ~-~-> Firmware Upgrade**
++)))
++
++(((
++Select the required image and click (% style="color:red" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:red" %)**Process Update**(%%) to upgrade.
++)))
++
++
++(((
++(% style="color:red" %)**NOTE**(%%): You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)//**Preserve Settings**//(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
++)))
++
++
++(((
++The system will automatically boot into the new firmware after upgrade.
++)))
++
++[[image:1657158986600-386.png]]
++
++
++
++== 8.2  Upgrade via Linux console ==
++
++
++(((
++SCP the firmware to the system** (% style="color:green" %)/var(%%)** directory and then run
++)))
++
++(((
++(% style="color:#4472c4" %)** //root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**
++)))
++
++
++(((
++(% style="color:red" %)**NOTE**(%%): it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
++)))
++
++
++
++= 9.  FAQ =
++
++
++== 9.1  How can I configure for a customized frequency band? ==
++
++
++(((
++See below link for how to customize frequency band: [[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]
++)))
++
++(((
++
++
++
++)))
++
++== 9.2  Can I make my own firmware for the gateway, where can I find the source code? ==
++
++
++(((
++Yes, You can make your own firmware for the LPS8N for branding purposes or to add customized applications.
++)))
++
++(((
  The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]
++)))
++(((
++
--== 9.4 Can I use 868Mhz version for 915Mhz bands? ==
++
++)))
++== 9.3  Can I use 868Mhz version for 915Mhz bands? ==
++
++
  It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
--= 10. Trouble Shooting =
--== 10.1 I get kernel error when install new package, how to fix? ==
++= 10.  Trouble Shooting =
++
++== 10.1  I get kernel error when install new package, how to fix? ==
++
++
  In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:
  (% style="background-color:yellow" %)root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk
@@ -867,32 +867,45 @@
   (% style="background-color:yellow" %)* opkg_install_cmd: Cannot install package kmod-dragino2-si3217x.
++(((
  In this case, you can use the –force-depends option to install such package as long as the actual kernel version is the same.
++)))
  (% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends
--== 10.2 How to recover the DLOS8N if the firmware crashes ==
--Please follow this instruction to recover your gateway:
++== 10.2  How to recover the LPS8N if the firmware crashes ==
--[[http:~~/~~/wiki.dragino.com/index.php?title=Recover_Gateway>>url:http://wiki.dragino.com/index.php?title=Recover_Gateway]]
++(((
++Please follow this instruction to recover your gateway:  [[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]
++)))
--== 10.3 I configured DLOS8N for WiFi access and lost its IP. What to do now? ==
++(((
++
--[[image:1652435238615-272.png||height="247" width="727"]]
++
++)))
--The DLOS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access DLOS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
++== 10.3  I configured LPS8N for WiFi access and lost its IP. What to do now? ==
--(% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.
++[[image:1657159323292-776.png]]
--Steps to connect via fall back IP:
--~1. Connect PC’s Ethernet port to DLOS8N’s WAN port
++(((
++The LPS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LPS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
++)))
--2. Configure PC’s Ethernet port has
++(% style="color:red" %)**Note: fallback IP can be disabled in the WAN and DHCP page.**
++
++
++**Steps to connect via fall back IP:**
++
++~1. Connect PC's Ethernet port to LG01's WAN port
++
++2. Configure PC's Ethernet port has
      IP: 172.31.255.253 and
      Netmask: 255.255.255.252
@@ -900,49 +900,70 @@
  [[image:1652435256286-879.png]]
--3. In the PC, use IP address 172.31.255.254 to access the DLOS8N via Web or Console.
++3. In the PC, use IP address 172.31.255.254 to access the LPS8N via Web or Console.
  Please note the latest firmware uses port 8000 for http and 2222 for ssh access.
--= 11. Order Info =
--(% style="color:#4f81bd" %) **//PART: DLOS8N-XXX-YYY//: **
++== 10.4  I connect to the LPS8N's SSID but LPS8N didn't assign DHCP IP to my laptop? ==
--(% style="color:#4f81bd" %) **//XXX: Frequency Band//**
--* (% style="color:#4f81bd" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
--* (% style="color:#4f81bd" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
++(((
++This is a known bug for the firmware version before 2019-09-23 for LPS, the issue was fixed since version: LG02_LG08~-~-build-v5.2.1569218466-20190923-1402.
++)))
--(% style="color:#4f81bd" %) **//YYY: 4G Cellular Option//**
++(((
++In the old version, user can use the [[fall back ip method >>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]]to access and configure the device.
++)))
--* (% style="color:#4f81bd" %)** E**(% style="color:black" %): EMEA, Korea, Thailand, India.
--* (% style="color:#4f81bd" %)** A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
--* (% style="color:#4f81bd" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
--* (% style="color:#4f81bd" %)** J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
++
++= 11.  Order Info =
++
++
++**//PART: (% style="color:blue" %)LPS8N-XXX-YYY//: (%%)**
++
++
++(% style="color:blue" %) **//XXX~://**(%%)**// Frequency Band//**
++
++* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
++* (% style="color:red" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
++
++(% style="color:blue" %) **//YYY~://**(%%)**// 4G Cellular Option//**
++
++* (% style="color:red" %)** EC25-E**(% style="color:black" %): EMEA, Korea, Thailand, India.
++* (% style="color:red" %)** EC25-A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
++* (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
++* (% style="color:red" %)** EC25-J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
++
  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
--= 12. Packing Info =
++= 12.  Packing Info =
++
++
++(((
  **Package Includes**:
++)))
  * DLOS8N LoRaWAN Gateway x 1
  * Stick Antenna for LoRa RF part. Frequency is one of 470 or 868 or 915Mhz depends the model ordered
  * Packaging with environmental protection paper box
++(((
  **Dimension and weight**:
++)))
  * Device Size: 12 x 12 x 3 cm
  * Weight: 187g
  * Package Size: 14.5 x 13.5 x 6 cm
  * Weight: 300g
--*
--= 13. Support =
++= 13.  Support =
--* Try to see if your questions already answered in the [[wiki>>url:http://wiki.dragino.com/]].
++* Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.
  Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to:[[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]

1652436675869-206.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.1 KB

Content

1652436705761-420.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.8 KB

Content

1652436787176-950.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.7 KB

Content

1656917428377-954.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+119.7 KB

Content

1656918270059-192.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+167.7 KB

Content

1657079015096-949.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+101.7 KB

Content

1657079055940-721.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+214.1 KB

Content

1657085974260-168.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+34.1 KB

Content

1657086105922-299.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+47.1 KB

Content

1657086192720-649.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+69.7 KB

Content

1657088560833-398.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+180.6 KB

Content

1657088818095-182.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+85.0 KB

Content

1657090855037-497.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+240.1 KB

Content

1657090932270-444.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+43.0 KB

Content

1657091099235-452.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+167.1 KB

Content

1657091257648-882.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+167.7 KB

Content

1657091583941-544.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+104.2 KB

Content

1657091719947-297.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+73.3 KB

Content

1657091739530-531.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+230.0 KB

Content

1657091941182-367.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+46.6 KB

Content

1657094130908-567.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+62.3 KB

Content

1657094183213-301.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+83.0 KB

Content

1657094202420-798.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+165.1 KB

Content

1657094221515-510.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+110.1 KB

Content

1657094249818-468.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+128.2 KB

Content

1657094333704-207.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+149.9 KB

Content

1657094382177-591.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+202.7 KB

Content

1657094417175-831.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+43.2 KB

Content

1657094444802-101.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+64.0 KB

Content

1657094475730-208.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+47.0 KB

Content

1657094646429-966.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+60.4 KB

Content

1657094674045-755.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+63.7 KB

Content

1657094791060-639.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+45.9 KB

Content

1657094893942-726.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+185.3 KB

Content

1657094930903-357.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+125.7 KB

Content

1657095412271-942.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+54.2 KB

Content

1657155158184-134.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+69.0 KB

Content

1657155183982-792.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+52.8 KB

Content

1657155288223-566.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+30.7 KB

Content

1657155457089-430.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+46.6 KB

Content

1657155507672-204.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+43.0 KB

Content

1657155554265-721.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+90.5 KB

Content

1657155630849-656.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+59.9 KB

Content

1657156052651-770.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+39.3 KB

Content

1657156094153-520.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+100.3 KB

Content

1657156156755-811.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+12.2 KB

Content

1657156199070-491.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+39.9 KB

Content

1657156300781-933.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+63.2 KB

Content

1657156341198-226.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+58.2 KB

Content

1657157402578-508.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+87.2 KB

Content

1657158190234-805.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+221.0 KB

Content

1657158198733-338.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+62.4 KB

Content

1657158255685-710.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+133.4 KB

Content

1657158986600-386.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+100.3 KB

Content

1657159323292-776.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+73.5 KB

Content

image-20220513184125-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+139.3 KB

Content

image-20220615204306-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+45.8 KB

Content

image-20220615204341-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+51.5 KB

Content

image-20220615204725-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+112.8 KB

Content

image-20220615204938-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+95.9 KB

Content

image-20220615205338-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+137.1 KB

Content

image-20220615205416-6.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+134.4 KB

Content

image-20220616083933-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+86.3 KB

Content

image-20220706115518-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.0 KB

Content

image-20220706115518-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.8 KB

Content

image-20220706115518-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.1 KB

Content

image-20220706115518-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.9 KB

Content

image-20220706155323-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+121.7 KB

Content

image-20220706155323-6.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+74.6 KB

Content

image-20220707092040-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+106.4 KB

Content

image-20220707092040-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+105.1 KB

Content

image-20220707092040-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+142.9 KB

Content

image-20220707112053-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+106.4 KB

Content

image-20220707112053-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Xiaoling

Size

...	...	@@ -1,0 +1,1 @@
	1	+105.1 KB

Content