Last modified by Kilight Cao on 2024/05/18 14:36
<
From version < 179.1 >
edited by Kilight Cao
on 2023/11/16 11:29
To version < 194.1 >
edited by Kilight Cao
on 2024/04/19 14:55
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LPS8N - LoRaWAN Gateway User Manual
1 +LPS8N -- LoRaWAN Gateway User Manual
Content
... ... @@ -4,7 +4,7 @@
4 4  
5 5  
6 6  
7 -**Table of Contents：**
7 +**Table of Contents:**
8 8  
9 9  {{toc/}}
10 10  
... ... @@ -79,7 +79,7 @@
79 79  * Up to -140 dBm sensitivity
80 80  * 70 dB CW interferer rejection at 1 MHz offset
81 81  * Able to operate with negative SNR, CCR up to 9dB
82 -* Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator
82 +* 8 x 8 channels LoRa packet detectors,8 x SF5-SF12 LoRa demodulators,8 x SF5-SF10 LoRa demodulators,125/250/500 kHz LoRa demodulator and 1 x (G)FSK demodulator
83 83  * Dual digital TX & RX radio front-end interfaces
84 84  * 10 programmable parallel demodulation paths
85 85  * Dynamic data-rate (DDR) adaptation
... ... @@ -94,7 +94,6 @@
94 94  * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
95 95  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
96 96  
97 -
98 98  == 1.3  Features ==
99 99  
100 100  
... ... @@ -112,7 +112,6 @@
112 112  * Support LoRaWAN basic station.
113 113  * Optional 3G/4G cellular connection
114 114  
115 -
116 116  == 1.4  Hardware System Structure ==
117 117  
118 118  
... ... @@ -139,7 +139,6 @@
139 139  
140 140  * **ETH LED    **[[image:image-20220706115518-4.png||height="15" width="17"]] :  This LED shows the ETH interface connection status.
141 141  
142 -
143 143  == 1.7 Button Instruction ==
144 144  
145 145  
... ... @@ -179,7 +179,7 @@
179 179  
180 180  
181 181  (((
182 -User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the DLOS8N has the default IP (% style="color:green" %)10.130.1.1
179 +User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the LPS8N has the default IP (% style="color:green" %)10.130.1.1
183 183  
184 184  
185 185  )))
... ... @@ -208,7 +208,7 @@
208 208  === 2.1.4  Connect via Ethernet with fall back ip ===
209 209  
210 210  
211 -The WAN port also has a [[fall back ip address>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/#H11.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F||anchor="H11.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H11.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
208 +The WAN port also has a [[fall back ip address>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/#H11.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H11.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
212 212  
213 213  
214 214  == 2.2  Access Configure Web UI ==
... ... @@ -247,7 +247,6 @@
247 247  * **WiFi Client Mode**
248 248  * **WiFi AP Mode**
249 249  
250 -
251 251  == 3.2  Use WAN port to access Internet ==
252 252  
253 253  
... ... @@ -698,7 +698,7 @@
698 698  [[image:1652428648903-878.png||height="266" width="731"]]
699 699  
700 700  
701 -== 5.4  MQTT Settings ==
697 +== (% data-sider-select-id="901b4be6-9ff2-4d69-bbb1-a2ce5a602f9b" %)5.4  MQTT Settings(%%) ==
702 702  
703 703  
704 704  (((
... ... @@ -713,95 +713,106 @@
713 713  [[image:1652428705046-212.png||height="417" width="733"]]
714 714  
715 715  
716 -== 5.5  System ==
712 +== (% data-sider-select-id="901b4be6-9ff2-4d69-bbb1-a2ce5a602f9b" %)5.5  Network(%%) ==
717 717  
718 -=== 5.5.1  System ~-~-> System Overview ===
714 +=== (% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %)5.5.1  (% data-sider-select-id="901b4be6-9ff2-4d69-bbb1-a2ce5a602f9b" %)Network(% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %) ~-~-> Network Status(%%) ===
719 719  
720 720  
721 -Shows the system info:
717 +[[image:image-20240419143226-2.png||height="742" width="950"]]
722 722  
723 723  
724 -[[image:image-20220826091810-6.png]]
720 +=== (% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %)5.5.2  (% data-sider-select-id="901b4be6-9ff2-4d69-bbb1-a2ce5a602f9b" %)Network(% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %) ~-~-> Network(%%) ===
725 725  
726 726  
727 -=== 5.5.2  System ~-~-> General ( login settings) ===
728 -
729 -
730 -[[image:1657155183982-792.png]]
731 -
732 -
733 733  (((
734 -(% style="color:#037691" %)**__System Password:__**
724 +(% data-sider-select-id="040776ba-bc4f-4586-9d1c-eb5b5c7f1e7d" style="color:#037691" %)**__LAN Settings:    __**(%%)When the LPS8N has the AP enable, LAN settings specify the network info for LPS8N's own network.
735 735  )))
736 736  
737 737  (((
738 -There are two login for LPS8N: (% style="color:blue" %)**root /dragino** (%%)or (% style="color:blue" %)**admin /dragino**. (%%)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
728 +(% style="color:#037691" %)__**WAN Settings:  **__(%%)Setting for LPS8N WAN port
739 739  )))
740 740  
741 741  (((
742 -This page can be used to set the password for them.
732 +(% style="color:#037691" %)__**WiFi Settings:  **__** **(%%)Setting for LPS8N WiFi IP when use it as WiFi Client
743 743  )))
744 744  
745 -(((
746 -(% style="color:#037691" %)**__Timezone:  __**(%%)Set device timezone.
747 -)))
735 +[[image:image-20240419143347-3.png]]
748 748  
749 -(((
750 -(% style="color:#037691" %)**__Port forwarding:  __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.
751 751  
752 -
753 -)))
738 +=== (% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %)5.5.3  (% data-sider-select-id="901b4be6-9ff2-4d69-bbb1-a2ce5a602f9b" %)Network(% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %) ~-~-> WiFi(%%) ===
754 754  
755 -=== 5.5.3  System ~-~-> Network ===
756 756  
741 +(% data-sider-select-id="e57f4efb-f39f-4e11-bde3-f13f9b08254d" %)
742 +LPS8N WiFi Settings.
757 757  
758 -[[image:1657155288223-566.png]]
759 759  
745 +[[image:image-20240419143504-4.png||height="500" width="946"]]
760 760  
761 -(((
762 -(% style="color:#037691" %)**__LAN Settings:    __**(%%)When the LPS8N has the AP enable, LAN settings specify the network info for LPS8N's own network.
763 -)))
764 764  
765 -(((
766 -(% style="color:#037691" %)__**WAN Settings:  **__(%%)Setting for LPS8N WAN port
767 -)))
748 +=== (% data-sider-select-id="be4c9623-8f61-4499-8859-fd388d34b2ab" %)5.5.4  Network ~-~-> Cellular(%%) ===
768 768  
769 -(((
770 -(% style="color:#037691" %)__**WiFi Settings:  **__** **(%%)Setting for LPS8N WiFi IP when use it as WiFi Client
771 771  
772 -
773 -)))
751 +While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
774 774  
775 -=== 5.5.4  System ~-~-> WiFi ===
753 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1657155507672-204.png?rev=1.1||alt="1657155507672-204.png"]]
776 776  
755 +(% style="color:red" %)**Note *: For LPS8N which doesn't have the cellular module, this page will shows Cellular not detected.**
777 777  
778 -LPS8N WiFi Settings.
779 779  
758 +== (% data-sider-select-id="9da31818-a029-4f0a-b9ff-645e219e4f4e" %)5.6  System(%%) ==
780 780  
781 -[[image:1657155457089-430.png]]
760 +=== (% data-sider-select-id="5eaf7530-1272-4643-b349-9de78d98959c" %)5.6.1  System ~-~-> System Overview(%%) ===
782 782  
783 783  
784 -=== 5.5.5  System ~-~-> Cellular ===
763 +Shows the system info:
785 785  
786 786  
787 -While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
766 +[[image:image-20220826091810-6.png]]
788 788  
789 789  
790 -[[image:1657155507672-204.png]]
769 +=== (% data-sider-select-id="63bebde2-7978-4bee-90b2-58884b714aea" %)5.6.2  System ~-~-> General ( login settings)(%%) ===
791 791  
792 792  
793 -(% style="color:red" %)**Note *: For LPS8N which doesn't have the cellular module, this page will shows Cellular not detected.**
772 +[[image:image-20240419144019-5.png]]
794 794  
774 +(((
775 +
795 795  
796 -=== 5.5.6  System ~-~-> Network Status ===
777 +(% style="color:#037691" data-sider-select-id="00e0325f-1698-4166-b578-eba5340e7e8e" %)**__System Password:__**
778 +)))
797 797  
780 +(((
781 +There are two login for LPS8N: (% style="color:blue" %)**root /dragino** (%%)or (% style="color:blue" %)**admin /dragino**. (%%)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
782 +)))
798 798  
799 -[[image:1657155554265-721.png]]
784 +(((
785 +This page can be used to set the password for them.
786 +)))
800 800  
788 +(((
789 +(% style="color:#037691" %)**__Timezone:  __**(%%)Set device timezone.
790 +)))
801 801  
802 -=== 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
792 +(((
793 +(% data-sider-select-id="be6bdce7-110b-4367-bcd5-d176d288153e" %)
794 +(% style="color:#037691" data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" %)**__Port forwarding:  __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.
803 803  
796 +(% data-sider-select-id="0e3c0e0e-5796-4a1a-b3da-cdfc059c383d" %)
797 +(% style="color:#037691" data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" %)**__Fallback Settings:  __**(%%)Enable/Disable the Fallback interface.
804 804  
799 +(% style="color:#037691" data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" %)**__Keepalive_Script:  __**(%%)Set the keepalive_scrpt interval.
800 +
801 +(% style="color:#037691" data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" %)**__Logread Level:  __**(%%)Change the logread level.
802 +
803 +(% data-sider-select-id="2140bc4a-c71f-4387-845a-510c0b050940" %)
804 +(% style="color:#037691" data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" %)**__Eable Internet Detect and Recover:  __**(%%)Enable/Disable the Internet Detect interface,Internet Detect is enabled by default. When there is no gateway network, it will reboot after 15 minutes.
805 +
806 +
807 +)))
808 +
809 +=== (% data-sider-select-id="7b902d7f-391d-4277-92fc-77ddd2546b9a" %)5.6.3  System ~-~-> Remote Mgnt & Auto Provision(%%) ===
810 +
811 +
805 805  Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
806 806  
807 807  
... ... @@ -833,7 +833,7 @@
833 833  [[image:1652429624400-864.png||height="432" width="716"]]
834 834  
835 835  
836 -=== 5.5.8  System ~-~-> Firmware Upgrade ===
843 +=== (% data-sider-select-id="48301489-7b19-464f-b442-96a6168a5e70" %)5.6.4  System ~-~-> Firmware Upgrade(%%) ===
837 837  
838 838  
839 839  We keep improving the LPS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
... ... @@ -890,7 +890,7 @@
890 890  (% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
891 891  
892 892  
893 -=== 5.5.9  System ~-~-> Reboot/Reset ===
900 +=== (% data-sider-select-id="373b3cff-3336-4ea9-b2e3-80b269a25dbb" %)5.6.5  System ~-~-> Reboot/Reset(%%) ===
894 894  
895 895  
896 896  [[image:1652430197132-330.png||height="256" width="724"]]
... ... @@ -899,7 +899,7 @@
899 899  
900 900  )))
901 901  
902 -=== 5.5.10  System ~-~-> Package Maintain ===
909 +=== (% data-sider-select-id="cc442f8d-4584-40ca-9073-38550c568e23" %)5.6.6  System ~-~-> Package Maintain(%%) ===
903 903  
904 904  
905 905  [[image:1657156199070-491.png]]
... ... @@ -908,9 +908,9 @@
908 908  Place to show what package has installed and possible to upgrade packages.
909 909  
910 910  
911 -== 5.6  LogRead ==
918 +== (% data-sider-select-id="393c2ac7-980d-4a0c-b0da-cab40221782d" %)5.7  LogRead(%%) ==
912 912  
913 -=== 5.6.1  LogRead ~-~-> LoRa Log ===
920 +=== (% data-sider-select-id="a1857d6d-7292-49a4-9c2b-821fdcd8435a" %)5.7.1 LogRead ~-~-> LoRa Log(%%) ===
914 914  
915 915  
916 916  Show the frequency for LoRa Radio and traffics.
... ... @@ -919,9 +919,16 @@
919 919  [[image:1657156300781-933.png]]
920 920  
921 921  
922 -=== 5.6.2  LogRead ~-~-> System Log ===
929 +=== (% data-sider-select-id="6e7c0405-1a69-41f7-a2d7-7c06ef64ecfe" %)5.7.2 LogRead ~-~-> Gateway Traffic(%%) ===
923 923  
931 +Show the gateway traffic:
924 924  
933 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20240416112159-1.png?width=872&height=610&rev=1.1||alt="image-20240416112159-1.png"]]
934 +
935 +
936 +=== (% data-sider-select-id="ce561240-23b4-4b3e-acc8-4a82ddba40f1" %)5.7.3 LogRead ~-~-> System Log(%%) ===
937 +
938 +
925 925  Show the system log
926 926  
927 927  
... ... @@ -928,6 +928,12 @@
928 928  [[image:1657156341198-226.png]]
929 929  
930 930  
945 +=== (% data-sider-select-id="c3f34a69-1c74-453c-a2b9-01ff619a05d2" %)5.7.4 LogRead ~-~-> Record Log(%%) ===
946 +
947 +This interface can record gateway logs:
948 +
949 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20240416112510-2.png?width=870&height=296&rev=1.1||alt="image-20240416112510-2.png"]]
950 +
931 931  = 6.  More features =
932 932  
933 933  == 6.1 Packet Filtering ==
... ... @@ -1001,7 +1001,7 @@
1001 1001  After updating the Chirpstack gateway-bridge firmware, there is no need to re-download and install the Chirpstack gateway-bridge package
1002 1002  
1003 1003  
1004 -== 6.6 How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive). ==
1024 +== 6.6  How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive). ==
1005 1005  
1006 1006  
1007 1007  USB card reader plugged into the USB port of the gateway
... ... @@ -1289,9 +1289,18 @@
1289 1289  == 10.3  Can I use 868Mhz version for 915Mhz bands? ==
1290 1290  
1291 1291  
1292 -It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
1312 +It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
1293 1293  
1294 1294  
1315 +== (% data-sider-select-id="59a03633-54e9-489e-a7d2-d0a332359cee" %)10.4  DIN Rail Mounting Reference.(%%) ==
1316 +
1317 +
1318 +[[image:image-20240318095136-1.jpeg||height="785" width="785"]]
1319 +
1320 +[[image:image-20240318095410-2.png||height="179" width="402"]]
1321 +
1322 +
1323 +
1295 1295  = 11.  Trouble Shooting =
1296 1296  
1297 1297  == 11.1  I get kernel error when install new package, how to fix? ==
... ... @@ -1370,9 +1370,31 @@
1370 1370  
1371 1371  (((
1372 1372  In the old version, user can use the [[fall back ip method >>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]]to access and configure the device.
1402 +
1403 +
1404 +== 11.5 When i power on LPS8N , i can only see PWR LED is on. other LEDs are not blinking. ==
1405 +
1406 +If there is no LED blink except the PWR led. There might be:
1407 +
1408 +1) Power adapter issue. In this case, please try another power adapter.
1409 +
1410 +2) Mother Board broken.
1373 1373  )))
1374 1374  
1375 1375  
1414 +(% data-sider-select-id="496725ea-6ec4-436c-82d7-547b7e14d448" %)
1415 +== (% data-sider-select-id="59a03633-54e9-489e-a7d2-d0a332359cee" %)11.6  (%%)Why does the gateway reboot every 15 minutes without Internet? ==
1416 +
1417 +
1418 +(% data-sider-select-id="4b74d469-5382-4aed-969a-48abd1fe271b" %)
1419 +Check whether Internet Detect is enabled on the System~-~->General interface.
1420 +
1421 +(% data-sider-select-id="2140bc4a-c71f-4387-845a-510c0b050940" %)
1422 +Internet Detect is enabled by default. When there is no gateway network, it will reboot after 15 minutes.
1423 +
1424 +[[image:image-20240419145139-6.png||height="639" width="856"]]
1425 +
1426 +
1376 1376  = 12.  Order Info =
1377 1377  
1378 1378  
... ... @@ -1413,7 +1413,6 @@
1413 1413  * Package Size: 14.5 x 13.5 x 6 cm
1414 1414  * Weight: 300g
1415 1415  
1416 -
1417 1417  = 14.  Support =
1418 1418  
1419 1419  
image-20240318095136-1.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +547.3 KB
Content
image-20240318095410-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +80.6 KB
Content
image-20240419143153-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +65.2 KB
Content
image-20240419143226-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +42.2 KB
Content
image-20240419143347-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +35.3 KB
Content
image-20240419143504-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +53.3 KB
Content
image-20240419144019-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +67.8 KB
Content
image-20240419145139-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Kilight
Size
... ... @@ -1,0 +1,1 @@
1 +119.8 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0