Changes for page LPS8N -- LoRaWAN Gateway User Manual

Last modified by Kilight Cao on 2024/05/18 14:36

From version < 158.4 >

edited by Xiaoling
on 2022/07/07 11:24

To version < 155.1 >

edited by Xiaoling
on 2022/07/07 09:56

Change comment: Uploaded new attachment "1657158986600-386.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 3 removed)

Details

Page properties

Content

@@ -6,7 +6,6 @@
  **Table of Contents：**
--{{toc/}}
@@ -104,8 +104,6 @@
  * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
--
--
  == 1.3  Features ==
  * Open Source OpenWrt system
@@ -122,8 +122,6 @@
  * Support LoRaWAN basic station.
  * Optional 3G/4G cellular connection
--
--
  == 1.4  Hardware System Structure ==
  [[image:1657079015096-949.png]]
@@ -148,8 +148,6 @@
  * **ETH LED    **[[image:image-20220706115518-4.png||height="15" width="17"]] :  This LED shows the ETH interface connection status.
--
--
  = 2.  Access and Configure LPS8N =
  (((
@@ -238,8 +238,6 @@
  * **WiFi Client Mode**
  * **WiFi AP Mode**
--
--
  == 3.2  Use WAN port to access Internet ==
  By default, the LPS8N is set to use the WAN port to connect to an upstream network. When you connect the LPS8N's WAN port to an upstream router, LPS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
@@ -250,7 +250,7 @@
  == 3.3  Access the Internet as a WiFi Client ==
--In the WiFi Client Mode, LPS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
++In the WiFi Client Mode, DLOS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
  (((
  The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~->  WiFi WAN Client Settings**
@@ -323,7 +323,7 @@
  )))
  (((
--This chapter describes how to use the LPS8N to work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
++This chapter describes how to use the DLOS8Nto work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
  )))
@@ -364,7 +364,6 @@
  * Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network
  * Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**
--
  (% style="color:#4f81bd" %)**Step 4: Create a Gateway**
  [[image:1657091941182-367.png]]
@@ -374,6 +374,7 @@
  Open the following page:
++
   [[image:image-20220706155323-5.png||height="579" width="1060"]]
@@ -389,7 +389,7 @@
  [[image:1657094130908-567.png]](% style="display:none" %)
--== 4.2  Configure LPS8N to connect to TTN v3 ==
++== 4.2  Configure DLOS8N to connect to TTN v3 ==
  (((
  You can now configure the LPS8N to let it connect to TTN network V3.
@@ -551,10 +551,8 @@
  (((
--(((
  After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:green" %)**LogRead ~-~-> LoRa Log**
  )))
--)))
  [[image:1657094930903-357.png]]
@@ -561,7 +561,7 @@
  Note *: **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
--=== 5.2.2  LoRa ~-~-> ABP Decryption ===
++=== 5.2.2 LoRa ~-~-> ABP Decryption ===
  The LPS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
@@ -617,13 +617,9 @@
  == 5.4  MQTT Settings ==
--(((
  If end nodes works in ABP mode, user can configure LPS8N to transfer the data to MQTT broker,
--)))
--(((
  Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**
--)))
  [[image:1652428705046-212.png||height="417" width="733"]]
@@ -713,15 +713,8 @@
  === 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
--Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
++Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:(% style="display:none" %)
--
--[[image:image-20220707112053-4.png||height="451" width="995"]]
--
--[[image:image-20220707112053-5.png||height="453" width="1004"]]
--
--(% style="display:none" %)
--
  (% style="display:none" %) [[image:1657157402578-508.png||height="450" width="992"]]
  (% id="cke_bm_589629S" style="display:none" %) [[image:image-20220707092040-2.png||height="452" width="1002"]]
@@ -729,16 +729,13 @@
  [[image:image-20220707092040-3.png||height="449" width="956"]]
--(((
--Please see this document for detail:  [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
--)))
++Please see this document for detail:(% style="display:none" %)
--(% style="display:none" %) (%%)
++[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
--(((
--R-SSH is for remote access device and management, introduction for how to use: [[Remote Access Gateway>>doc:Main.Remote Access Gateway.WebHome]]
--)))
++R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Remote Access Gateway.WebHome]]**
++
  [[image:1652429624400-864.png||height="432" width="716"]]
@@ -766,18 +766,12 @@
  [[image:1657156052651-770.png]]
--(((
  Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.
--)))
--(((
  (% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
--)))
--(((
  The system will automatically boot into the new firmware after upgrade.
--)))
  [[image:1657156094153-520.png]]
@@ -833,46 +833,30 @@
  == 6.1  Packet Filtering ==
--(((
  Drop unwanted packets.
--)))
--(((
  See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]
--)))
  == 6.2  Remote Access ==
--(((
  Remote Access Devices for management.
--)))
--(((
  Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Remote%20Access%20Gateway/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Remote%20Access%20Gateway/]]
--)))
  == 6.3  How to decode ABP LoRaWAN node ==
--(((
  Decode ABP:
--)))
--(((
  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20~~-~~--%20LG308/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]
--)))
  == 6.4  How to set data to MQTT broker ==
--(((
  Only support ABP LoRaWAN End Node
--)))
--(((
  Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]
--)))
  == 6.5  More instructions ==
@@ -890,10 +890,10 @@
  [[image:image-20220707092040-3.png||height="449" width="956"]](% style="display:none" %)
--(((
--Please see this document for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
--)))
++Please see this document for detail:
++[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
++
  (% style="display:none" %)  (%%)
  = 7.   (% style="display:none" %) (%%)Linux System =
@@ -976,7 +976,7 @@
  )))
  (((
--(% style="color:green" %)**root@dragino-169d30:~~# opkg update**             (% style="color:black" %)~/~/ to get the latest packages list
++(% style="color:green" %)**root@dragino-169d30:~~# opkg update**             (% style="color:black" %)~/~/ to get the latest packages list
  )))
  (((
@@ -1034,52 +1034,40 @@
  ( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )
--The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **(%%)is the upgrade Image. There are different methods to upgrade, as below.
++The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **is the upgrade Image. There are different methods to upgrade, as below.
  == 8.1  Upgrade via Web UI ==
--(((
--Go to the page: (% style="color:green" %)**Web ~-~-> System ~-~-> Firmware Upgrade**
--)))
++Go to the page: (% style="color:green" %)**Web à System à Firmware Upgrade**
--(((
  Select the required image and click (% style="color:red" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:red" %)**Process Update**(%%) to upgrade.
--)))
--(((
--(% style="color:red" %)**NOTE**(%%): You normally need to **//uncheck//** the //**Preserve Settings**// checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
--)))
++(% style="color:red" %)**NOTE**(%%): You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
--(((
  The system will automatically boot into the new firmware after upgrade.
--)))
--[[image:1657158986600-386.png]]
++[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png]]
++
  == 8.2  Upgrade via Linux console ==
--(((
--SCP the firmware to the system** (% style="color:green" %)/var(%%)** directory and then run
--)))
--(((
++SCP the firmware to the system** /var** directory and then run
++
  (% style="color:#4472c4" %)** //root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**
--)))
--(((
  (% style="color:red" %)**NOTE**(%%): it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
--)))
--= 9.  FAQ =
++= 9. FAQ =
--== 9.1  How can I configure for a customized frequency band? ==
++== 9.1 How can I configure for a customized frequency band? ==
  (((
  See below link for how to customize frequency band: **[[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
@@ -1089,10 +1089,15 @@
  )))
--== 9.2  Can I make my own firmware for the gateway, where can I find the source code? ==
++== 9.2 Can I connect DLOS8N to LORIOT? ==
++Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
++
++
++== 9.3 Can I make my own firmware for the gateway, where can I find the source code? ==
++
  (((
--Yes, You can make your own firmware for the LPS8N for branding purposes or to add customized applications.
++Yes, You can make your own firmware for the DLOS8N for branding purposes or to add customized applications.
  )))
  (((
@@ -1099,18 +1099,15 @@
  The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]
  )))
--(((
--
--)))
--== 9.3  Can I use 868Mhz version for 915Mhz bands? ==
++== 9.4 Can I use 868Mhz version for 915Mhz bands? ==
  It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
--= 10.  Trouble Shooting =
++= 10. Trouble Shooting =
--== 10.1  I get kernel error when install new package, how to fix? ==
++== 10.1 I get kernel error when install new package, how to fix? ==
  In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:
@@ -1133,7 +1133,7 @@
  (% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends
--== 10.2  How to recover the LPS8N if the firmware crashes ==
++== 10.2 How to recover the DLOS8N if the firmware crashes ==
  (((
  Please follow this instruction to recover your gateway:  **[[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]**
@@ -1143,13 +1143,12 @@
  )))
--== 10.3  I configured LPS8N for WiFi access and lost its IP. What to do now? ==
++== 10.3 I configured DLOS8N for WiFi access and lost its IP. What to do now? ==
--[[image:1657159323292-776.png]]
++[[image:1652435238615-272.png||height="247" width="727"]]
--
  (((
--The LPS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LPS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
++The DLOS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access DLOS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
  )))
  (% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.
@@ -1157,9 +1157,9 @@
  Steps to connect via fall back IP:
--~1. Connect PC's Ethernet port to LG01's WAN port
++~1. Connect PC’s Ethernet port to DLOS8N’s WAN port
--2. Configure PC's Ethernet port has
++2. Configure PC’s Ethernet port has
      IP: 172.31.255.253 and
      Netmask: 255.255.255.252
@@ -1167,45 +1167,31 @@
  [[image:1652435256286-879.png]]
--3. In the PC, use IP address 172.31.255.254 to access the LPS8N via Web or Console.
++3. In the PC, use IP address 172.31.255.254 to access the DLOS8N via Web or Console.
  Please note the latest firmware uses port 8000 for http and 2222 for ssh access.
--== 10.4  I connect to the LPS8N's SSID but LPS8N didn't assign DHCP IP to my laptop? ==
++= 11. Order Info =
--(((
--This is a known bug for the firmware version before 2019-09-23 for LPS, the issue was fixed since version: LG02_LG08~-~-build-v5.2.1569218466-20190923-1402.
--)))
++(% style="color:#4f81bd" %) **//PART: DLOS8N-XXX-YYY//: **
--(((
--In the old version, user can use the [[fall back ip method >>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]]to access and configure the device.
--)))
--
--
--= 11.  Order Info =
--
--
--(% style="color:#4f81bd" %)**//PART: LPS8N-XXX-YYY//: **
--
--
  (% style="color:#4f81bd" %) **//XXX: Frequency Band//**
--* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
--* (% style="color:red" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
++* (% style="color:#4f81bd" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
++* (% style="color:#4f81bd" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
--
  (% style="color:#4f81bd" %) **//YYY: 4G Cellular Option//**
--* (% style="color:red" %)** EC25-E**(% style="color:black" %): EMEA, Korea, Thailand, India.
--* (% style="color:red" %)** EC25-A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
--* (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
--* (% style="color:red" %)** EC25-J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
++* (% style="color:#4f81bd" %)** E**(% style="color:black" %): EMEA, Korea, Thailand, India.
++* (% style="color:#4f81bd" %)** A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
++* (% style="color:#4f81bd" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
++* (% style="color:#4f81bd" %)** J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
--= 12.  Packing Info =
++= 12. Packing Info =
  (((
  **Package Includes**:
@@ -1224,11 +1224,8 @@
  * Package Size: 14.5 x 13.5 x 6 cm
  * Weight: 300g
++= 13. Support =
--
--
--= 13.  Support =
--
  * Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.
  Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.

1657159323292-776.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-73.5 KB

Content

image-20220707112053-4.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-106.4 KB

Content

image-20220707112053-5.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-105.1 KB

Content

Changes for page LPS8N -- LoRaWAN Gateway User Manual

Summary

Details

Applications

Navigation