Last modified by Kilight Cao on 2024/05/18 14:36
<
From version < 158.3 >
edited by Xiaoling
on 2022/07/07 11:22
To version < 154.3 >
edited by Xiaoling
on 2022/07/07 09:54
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -6,7 +6,6 @@
6 6  
7 7  **Table of Contents：**
8 8  
9 -{{toc/}}
10 10  
11 11  
12 12  
... ... @@ -104,8 +104,6 @@
104 104  * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
105 105  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
106 106  
107 -
108 -
109 109  == 1.3  Features ==
110 110  
111 111  * Open Source OpenWrt system
... ... @@ -122,8 +122,6 @@
122 122  * Support LoRaWAN basic station.
123 123  * Optional 3G/4G cellular connection
124 124  
125 -
126 -
127 127  == 1.4  Hardware System Structure ==
128 128  
129 129  [[image:1657079015096-949.png]]
... ... @@ -148,8 +148,6 @@
148 148  
149 149  * **ETH LED    **[[image:image-20220706115518-4.png||height="15" width="17"]] :  This LED shows the ETH interface connection status.
150 150  
151 -
152 -
153 153  = 2.  Access and Configure LPS8N =
154 154  
155 155  (((
... ... @@ -238,8 +238,6 @@
238 238  * **WiFi Client Mode**
239 239  * **WiFi AP Mode**
240 240  
241 -
242 -
243 243  == 3.2  Use WAN port to access Internet ==
244 244  
245 245  By default, the LPS8N is set to use the WAN port to connect to an upstream network. When you connect the LPS8N's WAN port to an upstream router, LPS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
... ... @@ -250,7 +250,7 @@
250 250  
251 251  == 3.3  Access the Internet as a WiFi Client ==
252 252  
253 -In the WiFi Client Mode, LPS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
244 +In the WiFi Client Mode, DLOS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
254 254  
255 255  (((
256 256  The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**
... ... @@ -323,7 +323,7 @@
323 323  )))
324 324  
325 325  (((
326 -This chapter describes how to use the LPS8N to work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
317 +This chapter describes how to use the DLOS8Nto work with (TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
327 327  )))
328 328  
329 329  
... ... @@ -364,7 +364,6 @@
364 364  * Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network
365 365  * Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**
366 366  
367 -
368 368  (% style="color:#4f81bd" %)**Step 4: Create a Gateway**
369 369  
370 370  [[image:1657091941182-367.png]]
... ... @@ -374,6 +374,7 @@
374 374  
375 375  Open the following page:
376 376  
367 +
377 377   [[image:image-20220706155323-5.png||height="579" width="1060"]]
378 378  
379 379  
... ... @@ -389,7 +389,7 @@
389 389  [[image:1657094130908-567.png]](% style="display:none" %)
390 390  
391 391  
392 -== 4.2  Configure LPS8N to connect to TTN v3 ==
383 +== 4.2  Configure DLOS8N to connect to TTN v3 ==
393 393  
394 394  (((
395 395  You can now configure the LPS8N to let it connect to TTN network V3.
... ... @@ -551,10 +551,8 @@
551 551  (((
552 552  
553 553  
554 -(((
555 555  After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:green" %)**LogRead ~-~-> LoRa Log**
556 556  )))
557 -)))
558 558  
559 559  [[image:1657094930903-357.png]]
560 560  
... ... @@ -561,7 +561,7 @@
561 561  Note *: **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
562 562  
563 563  
564 -=== 5.2.2  LoRa ~-~-> ABP Decryption ===
553 +=== 5.2.2 LoRa ~-~-> ABP Decryption ===
565 565  
566 566  The LPS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
567 567  
... ... @@ -617,13 +617,9 @@
617 617  
618 618  == 5.4  MQTT Settings ==
619 619  
620 -(((
621 621  If end nodes works in ABP mode, user can configure LPS8N to transfer the data to MQTT broker,
622 -)))
623 623  
624 -(((
625 625  Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**
626 -)))
627 627  
628 628  
629 629  [[image:1652428705046-212.png||height="417" width="733"]]
... ... @@ -713,15 +713,8 @@
713 713  
714 714  === 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
715 715  
716 -Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
701 +Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:(% style="display:none" %) 
717 717  
718 -
719 -[[image:image-20220707112053-4.png||height="451" width="995"]]
720 -
721 -[[image:image-20220707112053-5.png||height="453" width="1004"]]
722 -
723 -(% style="display:none" %)
724 -
725 725  (% style="display:none" %) [[image:1657157402578-508.png||height="450" width="992"]]
726 726  
727 727  (% id="cke_bm_589629S" style="display:none" %) [[image:image-20220707092040-2.png||height="452" width="1002"]]
... ... @@ -729,16 +729,13 @@
729 729  [[image:image-20220707092040-3.png||height="449" width="956"]]
730 730  
731 731  
732 -(((
733 -Please see this document for detail:  [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
734 -)))
710 +Please see this document for detail:(% style="display:none" %)
735 735  
736 -(% style="display:none" %) (%%)
712 +[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
737 737  
738 -(((
739 -R-SSH is for remote access device and management, introduction for how to use: [[Remote Access Gateway>>doc:Main.Remote Access Gateway.WebHome]]
740 -)))
741 741  
715 +R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Remote Access Gateway.WebHome]]**
716 +
742 742  [[image:1652429624400-864.png||height="432" width="716"]]
743 743  
744 744  
... ... @@ -766,18 +766,12 @@
766 766  
767 767  [[image:1657156052651-770.png]]
768 768  
769 -(((
770 770  Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.
771 -)))
772 772  
773 773  
774 -(((
775 775  (% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
776 -)))
777 777  
778 -(((
779 779  The system will automatically boot into the new firmware after upgrade.
780 -)))
781 781  
782 782  [[image:1657156094153-520.png]]
783 783  
... ... @@ -960,7 +960,7 @@
960 960  )))
961 961  
962 962  (((
963 -(% style="color:green" %)**root@dragino-169d30:~~# opkg update**             (% style="color:black" %)~/~/ to get the latest packages list
932 +(% style="color:green" %)**root@dragino-169d30:~~# opkg update**  (% style="color:black" %)~/~/ to get the latest packages list
964 964  )))
965 965  
966 966  (((
... ... @@ -1018,52 +1018,40 @@
1018 1018  ( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LPS8N/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LIG16/Firmware/ChangeLog]] )
1019 1019  
1020 1020  
1021 -The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **(%%)is the upgrade Image. There are different methods to upgrade, as below.
990 +The file named as (% style="color:green" %)** xxxxx–xxxxx-squashfs-sysupgrade.bin **is the upgrade Image. There are different methods to upgrade, as below.
1022 1022  
1023 1023  
1024 1024  == 8.1 Upgrade via Web UI ==
1025 1025  
1026 -(((
1027 -Go to the page: (% style="color:green" %)**Web ~-~-> System ~-~-> Firmware Upgrade**
1028 -)))
995 +Go to the page: (% style="color:green" %)**Web à System à Firmware Upgrade**
1029 1029  
1030 -(((
1031 1031  Select the required image and click (% style="color:red" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:red" %)**Process Update**(%%) to upgrade.
1032 -)))
1033 1033  
1034 1034  
1035 -(((
1036 -(% style="color:red" %)**NOTE**(%%): You normally need to **//uncheck//** the //**Preserve Settings**// checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
1037 -)))
1000 +(% style="color:red" %)**NOTE**(%%): You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
1038 1038  
1039 1039  
1040 -(((
1041 1041  The system will automatically boot into the new firmware after upgrade.
1042 -)))
1043 1043  
1044 -[[image:1657158986600-386.png]]
1045 1045  
1006 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png]]
1046 1046  
1008 +
1047 1047  == 8.2 Upgrade via Linux console ==
1048 1048  
1049 -(((
1050 -SCP the firmware to the system** (% style="color:green" %)/var(%%)** directory and then run
1051 -)))
1052 1052  
1053 -(((
1012 +SCP the firmware to the system** /var** directory and then run
1013 +
1054 1054  (% style="color:#4472c4" %)** //root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**
1055 -)))
1056 1056  
1057 1057  
1058 -(((
1059 1059  (% style="color:red" %)**NOTE**(%%): it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
1060 -)))
1061 1061  
1062 1062  
1063 1063  
1064 -= 9.  FAQ =
1021 += 9. FAQ =
1065 1065  
1066 -== 9.1  How can I configure for a customized frequency band? ==
1023 +== 9.1 How can I configure for a customized frequency band? ==
1067 1067  
1068 1068  (((
1069 1069  See below link for how to customize frequency band: **[[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
... ... @@ -1073,10 +1073,15 @@
1073 1073  
1074 1074  )))
1075 1075  
1076 -== 9.2  Can I make my own firmware for the gateway, where can I find the source code? ==
1033 +== 9.2 Can I connect DLOS8N to LORIOT? ==
1077 1077  
1035 +Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
1036 +
1037 +
1038 +== 9.3 Can I make my own firmware for the gateway, where can I find the source code? ==
1039 +
1078 1078  (((
1079 -Yes, You can make your own firmware for the LPS8N for branding purposes or to add customized applications.
1041 +Yes, You can make your own firmware for the DLOS8N for branding purposes or to add customized applications.
1080 1080  )))
1081 1081  
1082 1082  (((
... ... @@ -1083,18 +1083,15 @@
1083 1083  The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]
1084 1084  )))
1085 1085  
1086 -(((
1087 -
1088 -)))
1089 1089  
1090 -== 9.3  Can I use 868Mhz version for 915Mhz bands? ==
1049 +== 9.4 Can I use 868Mhz version for 915Mhz bands? ==
1091 1091  
1092 1092  It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
1093 1093  
1094 1094  
1095 -= 10.  Trouble Shooting =
1054 += 10. Trouble Shooting =
1096 1096  
1097 -== 10.1  I get kernel error when install new package, how to fix? ==
1056 +== 10.1 I get kernel error when install new package, how to fix? ==
1098 1098  
1099 1099  In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:
1100 1100  
... ... @@ -1117,7 +1117,7 @@
1117 1117  (% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends
1118 1118  
1119 1119  
1120 -== 10.2  How to recover the LPS8N if the firmware crashes ==
1079 +== 10.2 How to recover the DLOS8N if the firmware crashes ==
1121 1121  
1122 1122  (((
1123 1123  Please follow this instruction to recover your gateway:  **[[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]**
... ... @@ -1127,13 +1127,12 @@
1127 1127  
1128 1128  )))
1129 1129  
1130 -== 10.3  I configured LPS8N for WiFi access and lost its IP. What to do now? ==
1089 +== 10.3 I configured DLOS8N for WiFi access and lost its IP. What to do now? ==
1131 1131  
1132 -[[image:1657159323292-776.png]]
1091 +[[image:1652435238615-272.png||height="247" width="727"]]
1133 1133  
1134 -
1135 1135  (((
1136 -The LPS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LPS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
1094 +The DLOS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access DLOS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
1137 1137  )))
1138 1138  
1139 1139  (% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.
... ... @@ -1141,9 +1141,9 @@
1141 1141  
1142 1142  Steps to connect via fall back IP:
1143 1143  
1144 -~1. Connect PC's Ethernet port to LG01's WAN port
1102 +~1. Connect PC’s Ethernet port to DLOS8N’s WAN port
1145 1145  
1146 -2. Configure PC's Ethernet port has
1104 +2. Configure PC’s Ethernet port has
1147 1147   IP: 172.31.255.253 and
1148 1148   Netmask: 255.255.255.252
1149 1149  
... ... @@ -1151,45 +1151,31 @@
1151 1151  
1152 1152  [[image:1652435256286-879.png]]
1153 1153  
1154 -3. In the PC, use IP address 172.31.255.254 to access the LPS8N via Web or Console.
1112 +3. In the PC, use IP address 172.31.255.254 to access the DLOS8N via Web or Console.
1155 1155  
1156 1156  Please note the latest firmware uses port 8000 for http and 2222 for ssh access.
1157 1157  
1158 1158  
1159 -== 10.4  I connect to the LPS8N's SSID but LPS8N didn't assign DHCP IP to my laptop? ==
1117 += 11. Order Info =
1160 1160  
1161 -(((
1162 -This is a known bug for the firmware version before 2019-09-23 for LPS, the issue was fixed since version: LG02_LG08~-~-build-v5.2.1569218466-20190923-1402.
1163 -)))
1119 +(% style="color:#4f81bd" %) **//PART: DLOS8N-XXX-YYY//: **
1164 1164  
1165 -(((
1166 -In the old version, user can use the [[fall back ip method >>||anchor="H10.3A0IconfiguredLPS8NforWiFiaccessandlostitsIP.Whattodonow3F"]]to access and configure the device.
1167 -)))
1168 -
1169 -
1170 -= 11.  Order Info =
1171 -
1172 -
1173 -(% style="color:#4f81bd" %)**//PART: LPS8N-XXX-YYY//: **
1174 -
1175 -
1176 1176  (% style="color:#4f81bd" %) **//XXX: Frequency Band//**
1177 1177  
1178 -* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1179 -* (% style="color:red" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1123 +* (% style="color:#4f81bd" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1124 +* (% style="color:#4f81bd" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1180 1180  
1181 -
1182 1182  (% style="color:#4f81bd" %) **//YYY: 4G Cellular Option//**
1183 1183  
1184 -* (% style="color:red" %)** EC25-E**(% style="color:black" %): EMEA, Korea, Thailand, India.
1185 -* (% style="color:red" %)** EC25-A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
1186 -* (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
1187 -* (% style="color:red" %)** EC25-J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
1128 +* (% style="color:#4f81bd" %)** E**(% style="color:black" %): EMEA, Korea, Thailand, India.
1129 +* (% style="color:#4f81bd" %)** A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
1130 +* (% style="color:#4f81bd" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
1131 +* (% style="color:#4f81bd" %)** J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
1188 1188  
1189 1189  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
1190 1190  
1191 1191  
1192 -= 12.  Packing Info =
1136 += 12. Packing Info =
1193 1193  
1194 1194  (((
1195 1195  **Package Includes**:
... ... @@ -1208,11 +1208,8 @@
1208 1208  * Package Size: 14.5 x 13.5 x 6 cm
1209 1209  * Weight: 300g
1210 1210  
1155 += 13. Support =
1211 1211  
1212 -
1213 -
1214 -= 13.  Support =
1215 -
1216 1216  * Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].
1217 1217  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.
1218 1218  Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.
1657158986600-386.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -100.3 KB
Content
1657159323292-776.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -73.5 KB
Content
image-20220707112053-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -106.4 KB
Content
image-20220707112053-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -105.1 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0