DLOS8N - DRAGINO

The DLOS8N is (% class="mark" %)an open source outdoor LoRaWAN Gateway(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.

23

24

DLOS8N (% class="mark" %)supports Semtech packet forwarder(%%) and (% class="mark" %)LoRaWAN Station connection(%%), it is fully compatible with LoRaWAN protocol. DLOS8N includes a(% class="mark" %) SX1302 LoRaWAN concentrator(%%).

25

26

DLOS8N has (% class="mark" %)pre-configured standard LoRaWAN frequency bands(%%) to use for different countries.User can also customize the frequency bands to use in their own LoRaWAN network.

27

28

DLOS8N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.

29

30

DLOS8N supports (% class="mark" %)auto-provision(%%) for mass deployment and long term maintain. System intergrator can easily change the settings.

31

32

[[image:1652411526195-923.png]]

33

34

35

== 1.2 Specifications ==

**Hardware System:**

Linux Part:

* 400Mhz ar9331 processor

* 64MB RAM

* 16MB Flash

**Interface:**

* 10M/100M RJ45 Ports x 1

48

* WiFi : 802.11 b/g/n

49

* LoRaWAN Wireless

50

* Power Input: 12 ~~ 24 V DC, 2 A

51

* IEEE 802.3 af compliant PoE port (DC 37 ~~ 57 v)

52

* USB 2.0 host connector x 1

53

* Mini-PCI E connector x 1

54

* SX1302 + 2 x SX1250

**WiFi Spec:**

* IEEE 802.11 b/g/n

* Frequency Band: 2.4 ~~ 2.462GHz

60

* Tx power:

61

** 11n tx power : mcs7/15: 11db mcs0 : 17db

62

** 11b tx power: 18db

63

** 11g 54M tx power: 12db

64

** 11g 6M tx power: 18db

* Wifi Sensitivity

** 11g 54M : -71dbm

** 11n 20M : -67dbm

**LoRa Spec:**

* Up to -140 dBm sensitivity with SX1250 Tx/Rx front-end

72

* 70 dB CW interferer rejection at 1 MHz offset

73

* Able to operate with negative SNR, CCR up to 9dB

74

* Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator

75

* Dual digital TX & RX radio front-end interfaces

76

* 10 programmable parallel demodulation paths

77

* Dynamic data-rate (DDR) adaptation

78

* True antenna diversity or simultaneous dual-band operation

79

80

**Cellular 4G LTE (optional):**

81

82

* Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]

83

* Standard Size SIM Slot

84

* 2 x 4G Sticker Antenna.

85

* Up to 150Mbps downlink and 50Mbps uplink data rates

86

* Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage

87

* MIMO technology meets demands for data rate and link reliability in modem wireless communication systems

88

89

**Power over Ethernet:**

90

91

* IEEE 802.3af compliant.

92

* Support wide input voltage range 37Vdc to 57Vdc.

93

* Thermal cut off.

94

* Short circuit protection.

95

* Over current protection

96

* Isolation level 4 KVrms.

97

* Enhanced surge protection

== 1.3 Features ==

* Open Source Embedded Linux system

102

* Managed by Web GUI, SSH via LAN or WiFi

103

* Support Semtech UDP packet forwarder

104

* Support LoRaWAN Station Connection

105

* Cellular Failover conntection(option)

106

* Direct Communication to LoRaWAN ABP Node

107

* LoRaWAN packet filtering

108

* Far seeing LED indicator

109

* Built-in GPS module for location & timing

110

* External fiber glass antenna

* Auto-Provision

* Remote Monitoring

* 802.3af PoE

* IP65

* Lighting Protection

116

* Power Consumption:12v ,300-500mA

117

118

== 1.4 Hardware System Structure ==

119

120

[[image:1652411641871-482.png||height="425" width="732"]]

121

122

123

== 1.5 DLOS8N Applications ==

124

125

[[image:1652411671209-920.png||height="618" width="650"]]

126

127

128

== 1.6 LED Indicators ==

129

130

[[image:1652411720670-489.png]]

131

132

133

There is a waterproof triple color LED on DLOS8N enclosure, the meaning of the LED is:

(((

(((

* (((

(% style="color:green" %)**SOLID GREEN**: (% style="color:black" %)DLOS8N is alive with LoRaWAN server connection.

)))

)))

* (((

(% style="color:green" %)**BLINKING GREEN**:(% style="color:black" %) a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will (% style="color:green" %)**BLINKING GREEN**(% style="color:black" %) for several seconds and then (% style="color:red" %)**RED** (% style="color:black" %)and (% style="color:#ffc000" %)**YELLOW** (% style="color:black" %)will blink together.

144

)))

145

* (((

146

(% style="color:red" %)**SOLID RED**: (% style="color:black" %)Device doesn’t have Internet connection.

)))

)))

== 1.7 WiFi Direction ==

152

153

DLOS8N use directional WiFi Antenna. The best direction is as below:

154

155

[[image:1652412859663-161.png||height="341" width="333"]]

156

157

158

= 2. Access and Configure DLOS8N =

159

160

The DLOS8N is configured as a WiFi Access Point by default. User can access and configure the DLOS8N after connecting to its WiFi network, or via its Ethernet port.

161

162

== 2.1 Find IP address of DLOS8N ==

163

164

=== 2.1.1 Connect via WiFi ===

165

166

[[image:1652412985720-934.png]]

167

168

169

At the first boot of DLOS8N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(% style="color:black" %)with password:

170

171

[[image:1652413127647-377.png]]

172

173

(% style="background-color:#ffffcc" %)dragino+dragino

174

175

User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the DLOS8N has the default IP (% style="color:green" %)10.130.1.1

176

177

178

=== 2.1.2 Connect via Ethernet with DHCP IP from router ===

179

180

[[image:1652414114583-532.png]]

181

182

183

Alternatively, connect the DLOS8N Ethernet port to your router and DLOS8N will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the DLOS8N. You can also use this IP to connect.

184

185

186

=== 2.1.3 Connect via WiFi with DHCP IP from router ===

187

188

[[image:1652414137639-956.png]]

189

190

191

If the DLOS8N already connect to the router via WiFi, use can use the WiFi IP to connect to DLOS8N.

192

193

194

=== 2.1.4 Connect via Ethernet with fall back ip ===

195

196

The WAN port also has a [[fall back ip address>>path:#_I_configured_LPS8]] for access if user doesn’t connect to uplink router. Click [[here>>path:#_I_configured_LPS8]] to see how to configure.

197

198

199

== 2.2 Access Configure Web UI ==

**Web Interface**

Open a browser on the PC and type the DLOS8N ip address (depends on your connect method)

204

205

[[http:~~/~~/10.130.1.1/>>url:http://10.130.1.1/]] (Access via WiFi AP network)

or

http:~/~/IP_ADDRESS or [[http:~~/~~/ IP_ADDRESS:8000>>url:http://192.168.1.xx:8000]]

210

211

212

You will see the login interface of DLOS8N as shown below.

213

214

The account details for Web Login are:

215

216

(% style="color:#4f81bd" %)**User Name: root**

217

218

(% style="color:#4f81bd" %)**Password: dragino**

219

220

[[image:1652414287022-223.png]]

= 3. Typical Network Setup =

== 3.1 Overview ==

The DLOS8N supports flexible network set up for different environments. This section describes the typical network topology. The network set up includes:

230

231

* **WAN Port Internet Mode**

232

* **WiFi Client Mode**

* **WiFi AP Mode**

* **Cellular Mode**

== 3.2 Use WAN port to access Internet ==

237

238

By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N’s WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:

239

240

[[image:1652420169255-959.png]]

241

242

243

== 3.3 Access the Internet as a WiFi Client ==

244

245

In the WiFi Client Mode, DLOS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.

246

247

The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**

248

249

[[image:1652420327792-211.png]]

250

251

252

In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click Save & Apply to connect.

253

254

255

== 3.4 Access the Internet via Cellular ==

256

257

If the DLOS8N support 3G/4G Cellular modem option, When the label on the shell is displayed as Model : DLOS8N-EC25, it indicates that DLOS8 already has EC25 3G/4G modules,user can use it as main internet connection or back up.

258

259

260

First, release the four screws of DLOS8N, pull out PCB and install SIM card as below:

261

262

[[image:1652420606018-181.png]]

263

264

265

[[image:1652420718132-929.png]]

266

267

268

The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**

269

270

271

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

272

273

[[image:1652421032117-341.png]]

274

275

(% style="color:red" %)**Note** *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.

276

277

278

== 3.5 Check Internet connection ==

279

280

In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.

281

282

* GREEN Tick [[image:1652421151598-130.png||height="23" width="24"]] : This interface has Internet connection.

283

* Yellow Tick [[image:1652421168047-470.png||height="22" width="21"]] : This interface has IP address but don’t use it for internet connection.

284

* RED Cross [[image:1652421179500-890.png||height="24" width="27"]] : This interface doesn’t connected.

285

286

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

1. Example: Configure as a LoRaWAN gateway

293

294

DLOS8N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.

295

296

297

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

298

299

300

This chapter describes how to use the DLOS8Nto work with

301

302

[[T>>url:https://www.thethingsnetwork.org/]]heThingsNetwork v3(T[[TN>>url:https://www.thethingsnetwork.org/]] v3[[)>>url:http://)]][[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]] ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])

1.

11. Create a gateway in TTN V3 Server

309

310

**Step 1: Get a Unique gateway ID.**

311

312

Every DLOS8N has a unique gateway id. The ID can be found at LoRaWAN page:

313

314

315

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

316

317

318

The example gateway id is: **a840411e96744154**

319

320

321

**Step 2: Sign up a user account in TTN server**

322

323

[[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]

324

325

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

**Step 3: Choose the TTNv3 Cluster Picker**

334

335

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

336

337

338

**Note: Choose the cluster corresponds to a specific Gateway server address**

339

340

* Europe 1 **corresponding Gateway server address: **eu1.cloud.thethings.network

341

* North America 1 **corresponding Gateway server address:** nam1.cloud.thethings.network

342

* Australia 1 **corresponding Gateway server address:** au1.cloud.thethings.network

343

* Legacy V2 Console : **TTN v2 shuts down in December 2021**

344

345

**Step 4: Create a Gateway**

346

347

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

348

349

Click the Gateway icon and then click Add gateway.

350

351

Open the following page:

352

353

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

354

355

**Notice: **Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.

After creating the gateway, you can see the gateway info, as below.

360

361

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

1.

11. Configure DLOS8N to connect to TTN v3

366

367

You can now configure the DLOS8N to let it connect to TTN network V3.

368

369

Make sure your DLOS8N has a working Internet Connection first.

370

371

372

Choose the right server provider and click **Save&Apply**

373

374

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

**Note: **The server address must match the Gateway server address you choose in TTN V3.

379

380

381

In the home page, we can see the LoRaWAN connection is ready now.

382

383

384

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

In TTN v3 portal, we can also see the gateway is connected.

389

390

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]

1.

11. Configure frequency

397

398

We also need to set the frequency plan in DLOS8N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.

399

400

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

401

402

403

In logread page, user can check the frequency actually used.

404

405

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]

1.

11. Add a LoRaWAN End Device

412

413

This section shows how to add a LoRaWAN End device to a LoRaWAN network and see the data from TTN web site.

414

415

416

We use [[LT-22222-L>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]] IO Controller as a reference device - the setup for other LoRaWAN devices will be similar.

417

418

419

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.jpg]]

420

421

**Step 1**: Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.

422

423

424

Three codes are required to define the device in TTN v3:

425

426

* DEV EUI - Unique ID code for a particular device.

427

* APP EUI - ID code for an Application defined in TTN v3.

428

* APP Key - Unique key to secure communications with a particular device.

429

430

A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.

431

432

433

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]

434

435

436

Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands. Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.

437

438

439

For the TTN v3 server, you can use the codes set in the device as in the following example.

440

441

442

Select **Add Application** to open the screen below.

443

444

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

445

446

Open the **Application **select** Add end device**

447

448

449

Start Register the end device

450

451

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]

452

453

Select OTAA activation mode

454

455

456

The LoRaWAN version for your device should be provided by the manufacturer in a datasheet as LoRaWAN version or LoRaWAN specification. The most commonly used LoRaWAN versions are v1.0.2 and v1.0.3.

457

458

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]

459

460

First, input the End device ID, AppEUI and DevEUI.

461

462

463

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image039.png]]

464

465

Secondly, choose the corresponding frequency and LoRaWAN class capabilities.

466

467

468

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image040.png]]

469

470

Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.

471

472

473

**Step 2**: Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.

474

475

476

Note that it may take some time for the device data to appear in the TTN v3 display.

477

478

479

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image041.png]]

1. Web Configure Pages

1.

11. Home

Shows the system running status.

491

492

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image042.png]]

1.

11. LoRa Settings

111. LoRa ~-~-> LoRa

This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customized the band* as well.

502

503

504

Different DLOS8N hardware version can support different frequency range:

505

506

* **868**: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

507

* **915**: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

508

509

After user choose the frequency plan, he can see the actually frequency in used by checking the page **LogRead ~-~-> LoRa Log**

510

511

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image043.png]]

512

513

Note *: See this instruction for how to customize frequency band:

514

515

[[http:~~/~~/wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway>>url:http://wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway]]

1.

11.

111. LoRa ~-~-> ABP Decryption

522

523

The DLOS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:

524

525

* No internet connection.

526

* User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>url:http://wiki.dragino.com/index.php?title=MQTT_Forward_Instruction]]).

527

528

Detail of this feature: [[http:~~/~~/wiki.dragino.com/index.php?title=Communication_with_ABP_End_Node>>url:http://wiki.dragino.com/index.php?title=Communication_with_ABP_End_Node]]

529

530

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image044.png]]

1.

11. LoRaWAN Settings

111. LoRaWAN ~-~-> LoRaWAN

537

538

This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc

539

540

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image045.png]]

Note

~*: User can ignore the latitude and longitude settings here, DLOS8N will use the actually value from GPS module.

545

546

~**: Packet filter is to drop the unwanted LoRaWAN packet, instruction see here:

547

548

See [[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#Filter_unwanted_LoRaWAN_packets>>url:http://wiki.dragino.com/index.php?title=Main_Page#Filter_unwanted_LoRaWAN_packets]]

1.

11.

111. LoRaWAN ~-~-> Amazon AWS-IoT

555

556

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image046.png]]

557

558

Please see this instruction to know more detail and demo for how to connect to AWS-IoT LoRaWAN Core: [[http:~~/~~/wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core>>url:http://wiki.dragino.com/index.php?title=Notes_for_AWS-IoT-Core]]

1.

11.

111. LoRaWAN ~-~-> LORIOT

566

567

Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]

568

569

Instruction: [[http:~~/~~/wiki.dragino.com/index.php?title=Notes_for_LORIOT>>url:http://wiki.dragino.com/index.php?title=Notes_for_LORIOT]]

570

571

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image047.png]]

1.

11. MQTT Settings

If end nodes works in ABP mode, user can configure DLOS8N to transfer the data to MQTT broker,

Instruction:

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#MQTT_Forward_Instruction>>url:http://wiki.dragino.com/index.php?title=Main_Page#MQTT_Forward_Instruction]]

584

585

586

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image048.png]]

1.

11. System

111. System ~-~-> System Overview

592

593

Shows the system info:

594

595

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image049.png]]

1.

11.

111. System ~-~-> General ( login settings)

600

601

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image050.png]]

System Password:

There are two login for DLOS8N: root /dragino or admin /dragino. Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.

606

607

This page can be used to set the password for them.

Timezone:

Set device timezone.

Port forwarding:

Enable/Disable the HTTP and SSH access via WAN interface.

1.

11.

111. System ~-~-> Network

625

626

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image051.png]]

LAN Settings:

When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N’s own network.

WAN Settings:

Setting for DLOS8N WAN port

WiFi Settings:

Setting for DLOS8N WiFi IP when use it as WiFi Client

1.

11.

111. System ~-~-> WiFi

649

650

DLOS8N WiFi Settings.

651

652

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image052.png]]

1.

11.

111. System ~-~-> Cellular

658

659

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

660

661

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

662

663

Note *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.

1.

11.

111. System ~-~-> Network Status

671

672

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image053.png]]

1.

11.

111. System ~-~-> Remote Mgnt & Auto Provision

679

680

Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:

681

682

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image054.png]]

683

684

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image055.png]]

685

686

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image056.png]]

687

688

Please see this document for detail:

689

690

[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]

691

692

693

R-SSH is for remote access device and management, introduction for how to use:

694

695

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#Remote_Access_Gateway_via_Reverse_SSH>>url:http://wiki.dragino.com/index.php?title=Main_Page#Remote_Access_Gateway_via_Reverse_SSH]]

696

697

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image057.png]]

1.

11.

111. System ~-~-> Firmware Upgrade

703

704

We keep improving the DLOS8N Linux side firmware for new features and bug fixes. Below are the links for reference.

705

706

* **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],

707

708

( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )

709

710

* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].

711

712

( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )

713

714

715

The file named as **xxxxx–xxxxx-squashfs-sysupgrade.bin **is the upgrade Image. There are different methods to upgrade, as below.

716

717

718

**Web à System à Firmware Upgrade**

719

720

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image058.png]]

721

722

723

Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.

724

725

726

**NOTE**: You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.

The system will automatically boot into the new firmware after upgrade.

732

733

734

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image059.png]]

735

736

737

Note *: User can also upgrade firmware via Linux console

738

739

SCP the firmware to the system** /var** directory and then run

740

741

**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**

742

743

744

**NOTE**: it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.

1.

11.

111. System ~-~-> Reboot/Reset

750

751

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image060.png]]

1.

11.

111. System ~-~-> Package Maintain

758

759

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image061.png]]

760

761

Place to show what package has installed and possible to upgrade packages.

1.

11. LogRead

111. LogRead ~-~-> LoRa Log

769

770

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image062.png]]

771

772

Show the frequency for LoRa Radio and traffics.

1.

11.

111. LogRead ~-~-> System Log

Show the system log

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image063.png]]

1. More features

11. More instructions

787

788

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRa.2FLoRaWAN_Gateway_Instruction>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRa.2FLoRaWAN_Gateway_Instruction]]

1. Linux System

The DLOS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.

796

797

1.

798

11. SSH Access for Linux console

799

800

User can access the Linux console via the SSH protocol. Make sure your PC and the DLOS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.

801

802

803

IP address: IP address of DLOS8N

804

805

Port: 22 (via WiFi AP mode) or 2222 (via WAN Interface)

User Name: **root**

Password: **dragino** (default)

810

811

812

After logging in, you will be in the Linux console and can enter commands as shown below.

813

814

815

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image064.png]]

816

817

818

The “logread -f” command can be used to debug how system runs.

819

820

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image065.png]]

1.

11. Edit and Transfer files

827

828

The DLOS8N supports the **SCP protocol** and has a built-in **SFTP server**. There are many ways to edit and transfer files using these protocols.

829

830

831

In Windows, one of the easiest methods is using the [[WinSCP>>url:https://winscp.net/eng/index.php]] utility.

832

833

After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the DLOS8N, or edit the files directly in the windows.

834

835

836

Screenshot is as below:

837

838

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image066.png]]

1.

11. File System

The DLOS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.

845

846

847

The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the DLOS8N flash.

848

849

You can use an external USB flash memory device to extend the size of flash memory for storage.

1.

11. Package maintenance system

856

857

DLOS8N uses the OpenWrt [[OPKG package maint>>url:https://wiki.openwrt.org/doc/techref/opkg]][[e>>url:https://wiki.openwrt.org/doc/techref/opkg]][[n>>url:https://wiki.openwrt.org/doc/techref/opkg]][[ance>>url:https://wiki.openwrt.org/doc/techref/opkg]][[ system>>url:https://wiki.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure DLOS8N to use **//iperf //**.

858

859

860

Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>url:https://wiki.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/wiki.openwrt.org/doc/techref/opkg>>url:https://wiki.openwrt.org/doc/techref/opkg]])

861

862

863

In Linux Console run:

864

865

**root@dragino-169d30:~~# opkg update** ~/~/ to get the latest packages list

866

867

**root@dragino-169d30:~~# opkg list** ~/~/shows the available packages

868

869

**root@dragino-169d30:~~# opkg install iperf **~/~/ install iperf

870

871

The system will automatically install the required packages as shown below.

872

873

874

//root@dragino-169d30:/etc/opkg# opkg install iperf//

875

876

//Installing iperf (2.0.12-1) to root…//

877

878

//Downloading //[[//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk]]

879

880

//Installing uclibcxx (0.2.4-3) to root…//

881

882

//Downloading //[[//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk]]

883

884

//Configuring uclibcxx.//

885

886

//Configuring iperf.//

887

888

889

1. Upgrade Linux Firmware

890

891

1. FAQ

892

11. How can I configure for a customized frequency band?

893

894

See below link for how to customize frequency band:

895

896

[[http:~~/~~/wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway>>url:http://wiki.dragino.com/index.php?title=Customized_Frequency_Band_for_Gateway]]

1.

11. Can I connect DLOS8N to LORIOT?

901

902

Yes, the set up instruction is here: [[http:~~/~~/wiki.dragino.com/index.php?title=Notes_for_LORIOT>>url:http://wiki.dragino.com/index.php?title=Notes_for_LORIOT]]

1.

11. Can I make my own firmware for the gateway, where can I find the source code?

907

908

Yes, You can make your own firmware for the DLOS8N for branding purposes or to add customized applications.

909

910

The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]

1.

11. Can I use 868Mhz version for 915Mhz bands?

915

916

It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.

1. Trouble Shooting

11. I get kernel error when install new package, how to fix?

923

924

In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:

925

926

927

root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk

928

929

Installing kmod-dragino2-si3217x (3.10.49+0.2-1) to root…

Collected errors:

~* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-dragino2-si3217x:

934

935

* kernel (= 3.10.49-1-4917516478a753314254643facdf360a) *

936

937

~* opkg_install_cmd: Cannot install package kmod-dragino2-si3217x.

938

939

940

In this case, you can use the –force-depends option to install such package as long as the actual kernel version is the same.

941

942

Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends

1.

11. How to recover the DLOS8N if the firmware crashes

947

948

Please follow this instruction to recover your gateway:

949

950

[[http:~~/~~/wiki.dragino.com/index.php?title=Recover_Gateway>>url:http://wiki.dragino.com/index.php?title=Recover_Gateway]]

1.

11. I configured DLOS8N for WiFi access and lost its IP. What to do now?

958

959

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image067.png]]

960

961

The DLOS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access DLOS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.

962

963

(Note: fallback IP can be disabled in the WAN and DHCP page)

964

965

966

Steps to connect via fall back IP:

967

968

1. Connect PC’s Ethernet port to DLOS8N’s WAN port

969

1. Configure PC’s Ethernet port has

970

IP: 172.31.255.253 and

971

Netmask: 255.255.255.252

As below photo:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image068.jpg]]

976

977

1. In the PC, use IP address 172.31.255.254 to access the DLOS8N via Web or Console.

978

979

Please note the latest firmware uses port 8000 for http and 2222 for ssh access.

1. Order Info

**//PART: DLOS8N-XXX-YYY//:**

986

987

**//XXX: Frequency Band//**

988

989

* **868**: valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

990

* **915**: valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

991

992

**//YYY: 4G Cellular Option//**

993

994

* **E**: EMEA, Korea, Thailand, India.

995

* **A**: North America/ Rogers/AT&T/T-Mobile.

996

* **AU**: Latin America, New Zeland, Taiwan

997

* **J**: Japan, DOCOMO/SoftBank/ KDDI

998

999

More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].

1. Packing Info

**Package Includes**:

1007

1008

* DLOS8N LoRaWAN Gateway x 1

1009

* Stick Antenna for LoRa RF part. Frequency is one of 470 or 868 or 915Mhz depends the model ordered

1010

* Packaging with environmental protection paper box

1011

1012

**Dimension and weight**:

1013

1014

* Device Size: 12 x 12 x 3 cm

1015

* Weight: 187g

1016

* Package Size: 14.5 x 13.5 x 6 cm

* Weight: 300g

1. Support

* Try to see if your questions already answered in the [[wiki>>url:http://wiki.dragino.com/]].

1022

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.

1023

Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.

1024

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to:

1025

1026

[[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]

Wiki source code of DLOS8N

Applications

Navigation