Version 138.1 by Xiaoye on 2023/04/06 17:36
Show last authors
1 (% style="text-align:center" %)
2 [[image:1657010676286-732.png||height="452" width="452"]]
3
4
5
6
7 **Table of Contents：**
8
9 {{toc/}}
10
11
12
13
14
15
16
17
18
19
20
21
22 = 1.  Introduction =
23
24 == 1.1  What is the LG308N ==
25
26
27 (((
28 (((
29 The LG308N is an open source (% style="color:blue" %)**LoRaWAN Pico Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular network. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.
30 )))
31
32 (((
33 The LG308N uses (% style="color:blue" %)**Semtech packet forwarder** (%%)and fully compatible with LoRaWAN protocol. It includes a (% style="color:blue" %)**SX1302 LoRa concentrator**(%%), which provides 10 programmable parallel demodulation paths.
34 )))
35
36 (((
37 LG308N has (% style="color:blue" %)**pre-configured standard LoRaWAN frequency bands**(%%) to use for different countries. User can also (% style="color:blue" %)**customized the frequency bands**(%%) to use in their own LoRa network.
38 )))
39
40 (((
41 LG308N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.
42 )))
43 )))
44
45 (((
46
47 )))
48
49 [[image:1657010949218-224.png]]
50
51
52 == 1.2  Specifications ==
53
54
55 (% style="color:#037691" %)**Hardware System:**
56
57 (((
58 Linux Part:
59 )))
60
61 * 400Mhz ar9331 processor
62 * 64MB RAM
63 * 16MB Flash
64
65 (% style="color:#037691" %)**Interface:**
66
67 * 10M/100M RJ45 Ports x 2
68 * WiFi : 802.11 b/g/n
69 * LoRaWAN Wireless
70 * Power Input: 12 V DC, 2 A
71 * IEEE 802.3 af compliant PoE port (DC 37  ~~ 57 v)
72 * USB 2.0 host connector x 1
73 * Mini-PCI E connector x 1
74 * SX1302 + 2 x SX1250
75
76 (% style="color:#037691" %)**WiFi Spec:**
77
78 * IEEE 802.11 b/g/n
79 * Frequency Band: 2.4 ~~ 2.462GHz
80 * Tx power:
81 ** 11n tx power : mcs7/15: 11db     mcs0 : 17db
82 ** 11b tx power: 18db
83 ** 11g 54M tx power: 12db
84 ** 11g 6M tx power: 18db
85 * Wifi Sensitivity
86 ** 11g 54M : -71dbm
87 ** 11n 20M : -67dbm
88
89 (% style="color:#037691" %)**LoRa Spec:**
90
91 * Up to -142.5 dBm sensitivity with SX1250 Tx/Rx front-end
92 * 70 dB CW interferer rejection at 1 MHz offset
93 * Able to operate with negative SNR, CCR up to 9dB
94 * Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator
95 * Dual digital TX & RX radio front-end interfaces
96 * 10 programmable parallel demodulation paths
97 * Dynamic data-rate (DDR) adaptation
98 * True antenna diversity or simultaneous dual-band operation
99
100 (% style="color:#037691" %)**Cellular 4G LTE (optional):**
101
102 * Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
103 * Standard Size SIM Slot
104 * 2 x 4G Sticker Antenna.
105 * Up to 150Mbps downlink and 50Mbps uplink data rates
106 * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
107 * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
108
109
110 == 1.3  Features ==
111
112
113 * Open Source Linux system
114 * Managed by Web GUI, SSH via LAN or WiFi
115 * Emulates 49x LoRa demodulators
116 * LoRaWAN Gateway
117 * 10 programmable parallel demodulation paths
118
119
120 == 1.4  Hardware System Structure ==
121
122
123 [[image:image-20221101103113-1.png]]
124
125
126 == 1.5  LG308N Applications ==
127
128
129 [[image:1657011208596-209.png]]
130
131
132 == 1.6  LED Indicators ==
133
134
135 LG308N has totally 6 LEDs, They are:
136
137 * **Power LED  **[[image:image-20220705165446-1.png||height="15" width="16"]] : This (% style="color:red" %)**LED**(%%) will be **solid on** if the device is properly powered.
138 * **HEART LED **[[image:image-20220705165446-2.png||height="16" width="15"]] : No function yet. 
139 * **SYS LED** [[image:image-20220705165446-3.png||height="16" width="15"]] :  This** LED** will shows different colors on different state:
140 ** (% style="color:red" %)**SOLID**(%%):  Device is alive with LoRaWAN server connection.
141 ** (% style="color:red" %)**BLINKING**(%%)**:**  a) Device has internet connection but no LoRaWAN Connection.  or  b) Device is in booting stage, in this stage, it will (% style="color:red" %)**BLINKING**(%%)** **for several seconds.
142 ** (% style="color:red" %)**OFF**(%%):  Device doesn't have Internet connection.
143
144 * **ETH LED** [[image:image-20220705165446-5.png||height="15" width="17"]] [[image:image-20220705165446-5.png||height="15" width="17"]]: These two LEDs show the ETH interfaces connection status.
145 * **WiFi LED** [[image:image-20220705165446-6.png||height="15" width="15"]]** **:  This LED shows the WiFi interface connection status.
146
147 (((
148 (% style="color:red" %)**Note: Above LED indication are for firmware version > LG02_LG08~-~-build-v5.3.1584002217-20200312-1639**
149 )))
150
151
152 == 1.7 Button Instruction ==
153
154
155 LG308N has a black toggle button, which is:
156
157
158 (% style="color:blue" %)**//➢ //Long press 4-5s:                     **(%%)the gateway will reload the Network and Initialize wifi configuration
159
160 **LED status: ** SYS LED will BLINKING RED Until the reload is finished.
161
162
163 (% style="color:blue" %)**➢ Long press more than 30s:    **(%%)the gateway will restart and restore factory settings.
164
165 **LED status: ** When the user releases the button, the LED will TURN OFF.
166
167
168 = 2.  Access and Configure LG308N =
169
170
171 The LG308N is configured as a WiFi Access Point by default. User can access and configure the LG308N after connecting to its WiFi network, or via its Ethernet port.
172
173
174 == 2.1  Find IP address of LG308N ==
175
176 === 2.1.1  Connect via WiFi ===
177
178
179 [[image:1657011715859-829.png]]
180
181
182 At the first boot of LG308N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(%%)with password:
183
184
185 (% style="color:red" %)**Note: In latest version firmware, it has been password protected and the password is:  **(% style="background-color:yellow" %)**dragino+dragino**
186
187
188 [[image:1652413127647-377.png]]
189
190
191 (((
192 User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the LG308N has the default IP (% style="color:green" %)**10.130.1.1**
193
194
195 )))
196
197 === 2.1.2  Connect via WAN port with DHCP IP from router ===
198
199
200 [[image:1657011966663-484.png]]
201
202
203 (((
204 Alternatively, connect the LG308N** __WAN port__** to your router and LG308N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LG308N. You can also use this IP to connect.
205
206
207 )))
208
209 === 2.1.3  Connect via LAN port with direct connection from PC ===
210
211
212 [[image:1657012061799-674.png]]
213
214
215 (((
216 The LG308N __**LAN port**__ is configured as DHCP router by default, user can connect the PC to LAN port and set PC to DHCP mode, it will get IP from LAN port and be able to access to the device. The default IP in LAN port is 10.130.1.1
217 )))
218
219
220 === 2.1.4  Connect WiFi with DHCP IP from router ===
221
222
223 [[image:image-20220705171041-7.png]]
224
225
226 If the LG308N already connect to the router via WiFi, use can use the WiFi IP to connect to LG308N.
227
228
229 === 2.1.5  Connect via LAN port by fall back ip ===
230
231
232 The **LAN port** also has a [[fall back ip address>>path:#fallback_ip]] for access if user doesn't connect to uplink router.
233
234
235 == 2.2  Access Configure Web UI ==
236
237
238 **Web Interface**
239
240 Open a browser on the PC and type the LG308N ip address (depends on your connect method)
241
242 [[http:~~/~~/10.130.1.1/>>url:http://10.130.1.1/]] (Access via WiFi AP network)
243
244 or
245
246 http:~/~/IP_ADDRESS or http:~/~/ IP_ADDRESS:8000
247
248
249 You will see the login interface of DLOS8N as shown below.
250
251 The account details for Web Login are:
252
253 (% style="color:#4f81bd" %)**User Name: root**
254
255 (% style="color:#4f81bd" %)**Password:   dragino**
256
257
258 [[image:1652414287022-223.png]]
259
260
261 = 3.  Typical Network Setup =
262
263 == 3.1  Overview ==
264
265
266 (((
267 LG308N supports flexible network set up for different environment. This section describes the typical network topology can be set in LG308N. The typical network set up includes:
268 )))
269
270 * **WAN Port Internet Mode**
271 * **WiFi Client Mode**
272 * **WiFi AP Mode**
273 * **Cellular Mode**
274
275
276 == 3.2  Use WAN port to access Internet ==
277
278
279 By default, the LG308N is set to use the WAN port to connect to an upstream network. When you connect the LG308N's WAN port to an upstream router, LG308N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
280
281
282 [[image:1657012559318-672.png]]
283
284
285 == 3.3  Access the Internet as a WiFi Client ==
286
287
288 In the WiFi Client Mode, LG308N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
289
290 (((
291 The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**
292 )))
293
294 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916142159-25.png?rev=1.1||alt="image-20220916142159-25.png" height="398" width="859"]]
295
296 (((
297 In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click(% style="color:blue" %)** Save & Apply**(%%) to connect.
298
299
300 )))
301
302 == 3.4  Use built-in 4G modem for internet access ==
303
304
305 If the LG308N has 3G/4G Cellular modem, user can use it as main internet connection or back up.
306
307
308 First, install the Micro SIM card as below direction
309
310 Second, Power off/ ON LG308N to let it detect the SIM card.
311
312 [[image:image-20220705171836-8.png]]
313
314
315 (((
316 The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**
317 )))
318
319 (((
320 While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
321
322
323 )))
324
325 (((
326 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916141840-23.png?rev=1.1||alt="image-20220916141840-23.png" height="356" width="868"]]
327 )))
328
329
330 == 3.5  Check Internet connection ==
331
332
333 In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.
334
335 * GREEN Tick ​​​​ [[image:1652436675869-206.png||height="14" width="15"]] : This interface has Internet connection.
336 * Yellow  Tick  [[image:1652436705761-420.png||height="15" width="15"]] : This interface has IP address but don't use it for internet connection.
337 * RED Cross    [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn't connected.
338
339 [[image:1657012821329-972.png]]
340
341
342 = 4.  Example: Configure as a LoRaWAN gateway =
343
344
345 LG308N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.
346
347
348 (((
349 [[image:1657012860422-990.png]]
350
351
352 )))
353
354 This chapter describes how to use the LG308N to work with(TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
355
356
357 == 4.1  Create a gateway in TTN V3 Server ==
358
359
360 (((
361 (% style="color:blue" %)**Step 1: Get a Unique gateway ID.**
362
363
364 )))
365
366 (((
367 (((
368 Every LG308N has a unique gateway id. The ID can be found at LoRaWAN page:
369
370
371 )))
372 )))
373
374 (((
375 [[image:1657013108723-531.png]]
376
377
378 )))
379
380 The example gateway id is: (% style="color:green" %)**a840411e96744154**
381
382
383
384 (% style="color:blue" %)**Step 2: Sign up a user account in TTN server**
385
386
387 [[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]
388
389
390 [[image:1652422127479-258.png||height="346" width="738"]]
391
392
393
394 (% style="color:blue" %)**Step 3: Choose the TTNv3 Cluster Picker**
395
396
397 (((
398 [[image:1652422142236-792.png||height="356" width="737"]]
399
400
401 )))
402
403 (% style="color:red" %)**Note: Choose the cluster corresponds to a specific Gateway server address**
404
405
406 * Europe 1 (% style="color:red" %)**corresponding Gateway server address:** (% style="color:black" %)eu1.cloud.thethings.network
407 * North America 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)nam1.cloud.thethings.network
408 * Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network
409 * Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**
410
411 (% style="color:blue" %)**Step 4: Create a Gateway**
412
413
414 [[image:1652422440891-514.png||height="360" width="747"]]
415
416 Click the Gateway icon and then click Add gateway.
417
418
419 Open the following page:
420
421 [[image:1652422470352-518.png||height="391" width="716"]]
422
423
424 [[image:1652422479876-297.png||height="398" width="729"]]
425
426
427 (((
428 (% style="color:red" %)**Notice: Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.**
429
430
431 )))
432
433 After creating the gateway, you can see the gateway info, as below.
434
435
436 [[image:1652422509034-682.png||height="299" width="739"]]
437
438
439 == 4.2  Configure LG308N to connect to TTN v3 ==
440
441
442 (((
443 You can now configure the LG308N to let it connect to TTN network V3.
444 )))
445
446 (((
447 Make sure your LG308N has a working Internet Connection first.
448 )))
449
450 (((
451 Choose the right server provider and click (% style="color:blue" %)**Save&Apply.**
452
453
454 )))
455
456 [[image:1652422624783-580.png||height="327" width="729"]]
457
458
459 (% style="color:red" %)**Note: The server address must match the Gateway server address you choose in TTN V3.**
460
461
462 In the home page, we can see the LoRaWAN connection is ready now.
463
464
465 [[image:image-20220916171413-2.png]]
466
467
468
469 In TTN v3 portal, we can also see the gateway is connected.
470
471
472 [[image:1652422703020-955.png||height="343" width="730"]]
473
474
475 == 4.3  Configure frequency ==
476
477
478 We also need to set the frequency plan in LG308N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.
479
480
481 [[image:1652422737399-529.png||height="362" width="737"]]
482
483
484 In logread page, user can check the frequency actually used.
485
486 [[image:1652422763536-750.png||height="514" width="730"]]
487
488
489 == 4.4  Add a LoRaWAN End Device ==
490
491
492 (((
493 This section shows how to add a LoRaWAN End device to a LoRaWAN network and see the data from TTN web site.
494 )))
495
496 (((
497 We use [[LT-22222-L>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]] IO Controller as a reference device - the setup for other LoRaWAN devices will be similar.
498 )))
499
500 [[image:1652422794767-871.png]]
501
502 (((
503 (% style="color:blue" %)**Step 1**: (% style="color:black" %)Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.
504 )))
505
506 (((
507 Three codes are required to define the device in TTN v3:
508 )))
509
510 * DEV EUI - Unique ID code for a particular device.
511 * APP EUI - ID code for an Application defined in TTN v3.
512 * APP Key - Unique key to secure communications with a particular device.
513
514 (((
515
516
517 A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.
518
519
520 )))
521
522 [[image:1652422840936-838.png]]
523
524
525 (((
526 (% style="color:red" %)**Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands.  Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.**
527
528
529 )))
530
531 (((
532 For the TTN v3 server, you can use the codes set in the device as in the following example.
533 )))
534
535 (((
536 Select **Add Application** to open the screen below.
537 )))
538
539 [[image:1657014671459-433.png]]
540
541
542 Open the **Application **select** Add end device**
543
544
545 Start Register the end device
546
547 [[image:1652422975885-591.png||height="359" width="726"]]
548
549 (((
550 Select OTAA activation mode
551
552
553 )))
554
555 (((
556 The LoRaWAN version for your device should be provided by the manufacturer in a datasheet as LoRaWAN version or LoRaWAN specification. The most commonly used LoRaWAN versions are v1.0.2 and v1.0.3.
557 )))
558
559 [[image:1652422998005-968.png||height="352" width="744"]]
560
561 First, input the End device ID, AppEUI and DevEUI.
562
563
564 [[image:1652423022781-339.png||height="365" width="741"]]
565
566 Secondly, choose the corresponding frequency and LoRaWAN class capabilities.
567
568
569 [[image:1652423046741-467.png||height="355" width="736"]]
570
571 (((
572 Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.
573
574
575 )))
576
577 (((
578 (% style="color:blue" %)**Step 2**: (% style="color:black" %)Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.
579
580
581 )))
582
583 (((
584 (% style="color:red" %)**Note that it may take some time for the device data to appear in the TTN v3 display.**
585
586
587 )))
588
589 [[image:1652423277549-324.png||height="273" width="745"]]
590
591
592 = 5.  Web Configure Pages =
593
594 == 5.1  Home ==
595
596
597 Shows the system running status.
598
599
600 [[image:1657014949846-507.png]]
601
602
603 == 5.2  LoRa Settings ==
604
605 === 5.2.1  LoRa ~-~-> LoRa ===
606
607
608 (((
609 This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customized the band* as well.
610 )))
611
612 (((
613 Different LG308N hardware version can support different frequency range:
614 )))
615
616 * (% style="color:blue" %)**868**(%%): valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
617 * (% style="color:blue" %)**915**(%%): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
618
619 (((
620 After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:blue" %)**LogRead ~-~-> LoRa Log**
621
622
623 )))
624
625 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LG308N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1652422737399-529.png?rev=1.1||alt="1652422737399-529.png"]]
626
627
628 (% style="color:red" %)**Note *: [[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
629
630
631 === 5.2.2  LoRa ~-~-> ABP Decryption ===
632
633
634 The LG308N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
635
636 * No internet connection.
637 * User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).
638
639 (((
640
641
642 Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**
643
644
645 )))
646
647 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916114346-7.png?rev=1.1||alt="image-20220916114346-7.png" height="359" width="876"]]
648
649
650 == 5.3  LoRaWAN Settings ==
651
652 === 5.3.1  LoRaWAN ~-~-> LoRaWAN ===
653
654
655 This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc.
656
657
658 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916114929-8.png?rev=1.1||alt="image-20220916114929-8.png" height="707" width="860"]]
659
660
661 (% style="color:red" %)**Note:**
662
663 ~*: User can ignore the latitude and longitude settings here, LG308N will use the actually value from GPS module.
664
665 ~**: Packet filter is to drop the unwanted LoRaWAN packet, instruction see here:
666
667 **See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**
668
669
670 === 5.3.2  LoRaWAN ~-~-> LoRaWAN ~-~- Basic Station ===
671
672
673 [[image:image-20230406172421-1.png]]
674
675
676 The basic station mode support **TTN/AWS/Chirpstack/ThingPark/Senet** Platform.
677
678 Instruction:
679
680 [[The Thing Network>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20TTN/#H3.A0GatewayRegistrationforBasicsStation]] 
681
682 [[AWS-IoT LoRaWAN Core>>url:http://wiki.dragino.com/xwiki/bin/view/Main/AWS%20IoT%20Core%20for%20LoRaWAN/]]
683
684 [[Chirpstack>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H3.A0GatewayRegistrationforBasicsStation]]
685
686 ThingPark
687
688 [[Senet>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Connection%20to%20Senet/#H3.A0SemtechBasicStation]]
689
690 (((
691
692 )))
693
694 === 5.3.3  LoRaWAN ~-~-> LORIOT ===
695
696
697 (((
698 Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]
699 )))
700
701 (((
702 Instruction: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
703
704
705 )))
706
707 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916115143-9.png?rev=1.1||alt="image-20220916115143-9.png" height="316" width="864"]](% style="display:none" %)
708
709
710 == 5.4  MQTT Settings ==
711
712
713 (((
714 If end nodes works in ABP mode, user can configure LG308N to transfer the data to MQTT broker,
715 )))
716
717 (((
718 Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**
719 )))
720
721
722 [[image:1652428705046-212.png||height="417" width="733"]]
723
724
725 == 5.5  System ==
726
727 === 5.5.1  System ~-~-> System Overview ===
728
729
730 Shows the system info:
731
732
733 [[image:image-20220916173046-3.png||height="613" width="868"]]
734
735
736 === 5.5.2  System ~-~-> General ( login settings) ===
737
738
739 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916134411-11.png?rev=1.1||alt="image-20220916134411-11.png" height="499" width="865"]](% style="display:none" %)
740
741
742 (((
743 (% style="color:#037691" %)**__System Password:__**
744 )))
745
746 (((
747 There are two login for DLOS8: (% style="color:#4f81bd" %)**root /dragino** (% style="color:black" %)or (% style="color:#4f81bd" %)**admin /dragino**. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
748 )))
749
750 (((
751 This page can be used to set the password for them.
752 )))
753
754 (((
755 (% style="color:#037691" %)**__Timezone: __**(%%)Set device timezone.
756 )))
757
758 (((
759 (% style="color:#037691" %)**__Port forwarding: __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.
760
761
762 )))
763
764 === 5.5.3  System ~-~-> Network ===
765
766
767 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916134642-12.png?rev=1.1||alt="image-20220916134642-12.png" height="411" width="873"]]
768
769
770 (((
771 (% style="color:#037691" %)**__LAN Settings:  __**(%%)When the LG308N has the AP enable, LAN settings specify the network info for LG308N's own network.
772 )))
773
774 (((
775 (% style="color:#037691" %)__**WAN Settings: **__(%%)Setting for LG308N WAN port
776 )))
777
778 (((
779 (% style="color:#037691" %)__**WiFi Settings:  **__(%%)Setting for LG308N WiFi IP when use it as WiFi Client
780 )))
781
782
783 === 5.5.4  System ~-~-> WiFi ===
784
785
786 LG308N WiFi Settings.
787
788 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916134831-13.png?rev=1.1||alt="image-20220916134831-13.png" height="408" width="870"]]
789
790
791 === 5.5.5  System ~-~-> Cellular ===
792
793
794 While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
795
796
797 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916135100-14.png?rev=1.1||alt="image-20220916135100-14.png" height="347" width="874"]](% style="display:none" %)
798
799
800 (% style="color:red" %)**Note *: For LG308N which doesn't have the cellular module, this page will shows Cellular not detected.**
801
802
803 === 5.5.6  System ~-~-> Network Status ===
804
805
806 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916135207-15.png?rev=1.1||alt="image-20220916135207-15.png" height="599" width="882"]]
807
808
809 === 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
810
811
812 Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
813
814 [[image:1652429518191-846.png||height="332" width="733"]]
815
816 [[image:1652429527544-247.png||height="327" width="724"]]
817
818 [[image:1652429537849-154.png||height="339" width="722"]]
819
820
821 Please see this document for detail:
822
823 [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG308N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
824
825
826 R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Monitor & Remote Access Gateway.WebHome]]**
827
828 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140017-16.png?rev=1.1||alt="image-20220916140017-16.png" height="593" width="872"]]
829
830 (% style="display:none" %) (%%)
831
832 === 5.5.8  System ~-~-> Firmware Upgrade ===
833
834
835 We keep improving the DLOS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
836
837 * **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],
838
839 ( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )
840
841
842 * **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].
843
844 ( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )
845
846
847 (((
848 The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(%%)is the upgrade Image. There are different methods to upgrade, as below.
849 )))
850
851 (((
852 (% style="color:green" %)**Web~-~-> System~-~-> Firmware Upgrade**
853
854
855 )))
856
857 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140103-17.png?rev=1.1||alt="image-20220916140103-17.png" height="274" width="871"]]
858
859
860 (((
861 Select the required image and click (% style="color:blue" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:blue" %)**Process Update** (%%)to upgrade.
862
863
864 )))
865
866 (((
867 (% style="color:red" %)**NOTE**: (%%)You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)**Preserve Settings**(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
868
869
870 )))
871
872 (((
873 The system will automatically boot into the new firmware after upgrade.
874
875
876 )))
877
878 [[image:1652429962190-224.png||height="358" width="729"]]
879
880
881 (% style="color:red" %)**NOTE***(%%): User can also upgrade firmware via Linux console
882
883 SCP the firmware to the system(% style="color:green" %)**/var**(%%)** **directory and then run
884
885 (% style="color:#4f81bd" %)**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**
886
887
888 (% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
889
890
891 === 5.5.9  System ~-~-> Reboot/Reset ===
892
893
894 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140312-18.png?rev=1.1||alt="image-20220916140312-18.png" height="274" width="873"]]
895
896 (((
897
898 )))
899
900 === 5.5.10  System ~-~-> Package Maintain ===
901
902
903 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140421-19.png?rev=1.1||alt="image-20220916140421-19.png" height="687" width="868"]]
904
905
906 Place to show what package has installed and possible to upgrade packages.
907
908
909 == 5.6  LogRead ==
910
911 === 5.6.1  LogRead ~-~-> LoRa Log ===
912
913
914 Show the frequency for LoRa Radio and traffics.
915
916
917 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140549-20.png?rev=1.1||alt="image-20220916140549-20.png" height="734" width="883"]]
918
919
920 === 5.6.2  LogRead ~-~-> System Log ===
921
922
923 Show the system log
924
925
926 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140732-21.png?rev=1.1||alt="image-20220916140732-21.png" height="706" width="867"]]
927
928
929 = 6.  More features =
930
931 == 6.1 Packet Filtering ==
932
933
934 Drop unwanted packets.
935
936 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]
937
938
939 == 6.2 Remote Access ==
940
941
942 Remote Access Devices for management.
943
944 Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access]]
945
946
947 == 6.3 How to decode ABP LoRaWAN node ==
948
949
950 Decode ABP:
951
952 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20~~-~~--%20LG308/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]
953
954
955 == 6.4 How to set data to MQTT broker ==
956
957
958 Only support ABP LoRaWAN End Node
959
960 Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]
961
962
963 == 6.5 How the gateway connects to Chirpstack v3/v4 via gateway-bridge ==
964
965
966 **For Chirpstack v3 Gateway-bridge**:
967
968 The corresponding gateway firmware must be used :
969
970 [[Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge~~-~~-build-v5.4.1679487778-20230322-2024/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge--build-v5.4.1679487778-20230322-2024/]]
971
972 Chirpstack v3 via gateway-bridge Instruction: [[https:~~/~~/www.chirpstack.io/gateway-bridge/gateway/dragino/>>url:https://www.chirpstack.io/gateway-bridge/gateway/dragino/]]
973
974
975 **For Chirpstack v4 Gateway-bridge**:
976
977 The corresponding gateway firmware must be used :
978
979 [[Chirpstack-gateway-bridge/Chirpstack-Bridge-V4~~-~~-build-v5.4.1670655072-20221210-1452/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V4--build-v5.4.1670655072-20221210-1452/]]
980
981 Chirpstack v4 via gateway-bridge Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0HowthegatewayconnectstoChirpstackv4viagateway-bridge>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0HowthegatewayconnectstoChirpstackv4viagateway-bridge]]
982
983
984 (% style="color:red" %)**NOTE***(%%): Different chirpstack versions use different gateway-bridge configurations.
985
986 After updating the Chirpstack gateway-bridge firmware, there is no need to re-download and install the Chirpstack gateway-bridge package
987
988
989 == 6.6  More instructions ==
990
991
992 [[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)
993
994
995 = 7.  Linux System =
996
997
998 The LG308N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.
999
1000
1001 == 7.1  SSH Access for Linux console ==
1002
1003
1004 User can access the Linux console via the SSH protocol. Make sure your PC and the LG308N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.
1005
1006 IP address:  IP address of LG308N
1007
1008 Port:         22 (via WiFi AP mode) or 2222 (via WAN Interface)
1009
1010 User Name:      (% style="color:green" %)**root**
1011
1012 Password:         (% style="color:green" %)**dragino** (% style="color:black" %)(default)
1013
1014
1015 After logging in, you will be in the Linux console and can enter commands as shown below.
1016
1017 [[image:1652431588565-830.png]]
1018
1019
1020 The “** (% style="background-color:yellow" %)logread -f"(%%)**command can be used to debug how system runs.
1021
1022
1023 [[image:1657070133275-283.png]]
1024
1025
1026 == 7.2  Edit and Transfer files ==
1027
1028
1029 (((
1030 The LG308N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.
1031 )))
1032
1033 (((
1034 In Windows, one of the easiest methods is using the [[WinSCP>>url:https://winscp.net/eng/index.php]] utility.
1035 )))
1036
1037 (((
1038 After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the LG308N, or edit the files directly in the windows.
1039 )))
1040
1041 (((
1042 Screenshot is as below:
1043
1044
1045 )))
1046
1047 [[image:1652431650755-450.png]]
1048
1049
1050 == 7.3  File System ==
1051
1052
1053 (((
1054 (((
1055 The LG308N has a 16MB flash and a 64MB RAM. The /var and /tmp directory are in the RAM, contents stored in /tmp and /var will be erased after reboot the device. Other directories are in the flash and will keep after reboot.
1056 )))
1057
1058
1059 (((
1060 The Linux system use around 8MB ~~10MB flash size which means there is not much room for user to store data in the LG308N flash. User can use an external USB flash to extend the size for storage.
1061 )))
1062 )))
1063
1064
1065 == 7.4  Package maintenance system ==
1066
1067
1068 LG308N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure LG308N to use **//iperf //**.
1069
1070 (((
1071 Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])
1072 )))
1073
1074 (((
1075 **In Linux Console run:**
1076 )))
1077
1078 (((
1079 (% style="color:green" %)**root@dragino-169d30:~~# opkg update**           (% style="color:black" %)~/~/ to get the latest packages list
1080 )))
1081
1082 (((
1083 (% style="color:green" %)**root@dragino-169d30:~~# opkg list**    (% style="color:black" %) ~/~/shows the available packages
1084 )))
1085
1086 (((
1087 (% style="color:green" %)**root@dragino-169d30:~~# opkg install iperf ** (% style="color:black" %)~/~/ install iperf
1088 )))
1089
1090 The system will automatically install the required packages as shown below.
1091
1092
1093 (((
1094 (% style="background-color:#dcdcdc" %)//root@dragino-169d30:/etc/opkg# opkg install iperf//
1095 )))
1096
1097 (((
1098 (% style="background-color:#dcdcdc" %)//Installing iperf (2.0.12-1) to root…//
1099 )))
1100
1101 (((
1102 (% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk]]
1103 )))
1104
1105 (((
1106 (% style="background-color:#dcdcdc" %)//Installing uclibcxx (0.2.4-3) to root…//
1107 )))
1108
1109 (((
1110 (% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk]]
1111 )))
1112
1113 (((
1114 (% style="background-color:#dcdcdc" %)//Configuring uclibcxx.//
1115 )))
1116
1117 (((
1118 (% style="background-color:#dcdcdc" %)//Configuring iperf.//
1119
1120
1121 )))
1122
1123 = 8.  Upgrade Linux Firmware =
1124
1125
1126 = 9.  OTA System Update =
1127
1128
1129 LG308N supports system auto update via OTA, please see **[[this URL>>url:http://wiki.dragino.com/xwiki/bin/view/OTA%20Update/]]** for the detail of this feature.
1130
1131
1132 = 10.  FAQ =
1133
1134 == 10.1  How can I configure for a customized frequency band? ==
1135
1136
1137 (((
1138 See below link for how to customize frequency band: **[[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
1139 )))
1140
1141 (((
1142
1143 )))
1144
1145 == 10.2  Can I connect LG308N to LORIOT? ==
1146
1147
1148 Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
1149
1150
1151 == 10.3  Can I make my own firmware for the gateway, where can I find the source code? ==
1152
1153
1154 (((
1155 Yes, You can make your own firmware for the LG308N for branding purposes or to add customized applications.
1156 )))
1157
1158 (((
1159 The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]
1160 )))
1161
1162
1163 == 10.4  Can I use 868Mhz version for 915Mhz bands? ==
1164
1165
1166 It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
1167
1168
1169 == 10.5  Can I control the LEDs? ==
1170
1171
1172 Except the PWR LED is controlled by +3v3 power directly. All other LEDs can be controlled by developer.
1173
1174
1175 (% style="color:blue" %)**Control Globe LED:**
1176
1177 ON: echo 1 > /sys/class/leds/dragino2\:red\:wlan/brightness 
1178
1179 OFF: echo 0 > /sys/class/leds/dragino2\:red\:wlan/brightness
1180
1181
1182 (% style="color:blue" %)**Control HEART LED:**
1183
1184 First export the gpio27 and set to out
1185
1186 echo 27 > /sys/class/gpio/export
1187
1188 echo out > /sys/class/gpio/gpio27/direction
1189
1190 ON: echo 0 > /sys/class/gpio/gpio27/value
1191
1192 OFF: echo 1 > /sys/class/gpio/gpio27/value
1193
1194
1195 = 11.  Trouble Shooting =
1196
1197 == 11.1  I get kernel error when install new package, how to fix? ==
1198
1199
1200 In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:
1201
1202 (% style="background-color:yellow" %)root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk
1203
1204 (% style="background-color:yellow" %)Installing kmod-dragino2-si3217x (3.10.49+0.2-1) to root…
1205
1206 (% style="background-color:yellow" %)Collected errors:
1207
1208 (% style="background-color:yellow" %)* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-dragino2-si3217x:
1209
1210 (% style="background-color:yellow" %)*      kernel (= 3.10.49-1-4917516478a753314254643facdf360a) *
1211
1212 (% style="background-color:yellow" %)* opkg_install_cmd: Cannot install package kmod-dragino2-si3217x.
1213
1214 (((
1215 In this case, you can use the –force-depends option to install such package as long as the actual kernel version is the same.
1216 )))
1217
1218 (% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends
1219
1220
1221 == 11.2  How to recover the LG308N if the firmware crashes ==
1222
1223
1224 (((
1225 Please follow this instruction to recover your gateway:  **[[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]**
1226 )))
1227
1228 (((
1229
1230 )))
1231
1232 == 11.3  I configured LG308N for WiFi access and lost its IP. What to do now? ==
1233
1234
1235 [[image:1657074078183-336.png]]
1236
1237
1238 (((
1239 (((
1240 The LG308N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LG308N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
1241 )))
1242 )))
1243
1244
1245 (((
1246 (% style="color:red" %)**Note: fallback IP can be disabled in the WAN and DHCP page.**
1247 )))
1248
1249
1250 (((
1251 **Steps to connect via fall back IP:**
1252 )))
1253
1254 (((
1255 ~1. Connect PC's Ethernet port to LG01's LAN port
1256 )))
1257
1258 (((
1259 2. Configure PC's Ethernet port has IP: 172.31.255.253 and Netmask: 255.255.255.252
1260
1261
1262 )))
1263
1264 (((
1265 As below photo:
1266
1267
1268 )))
1269
1270 [[image:1652435256286-879.png]]
1271
1272
1273 3. In PC, use 172.31.255.254 to access LG308N via Web or Console.
1274
1275
1276 = 12.  Order Info =
1277
1278
1279 **//PART:(% style="color:blue" %) DLOS8N-XXX-YYY//: (%%)**(% style="color:blue" %)
1280
1281 (% style="color:blue" %)**//XXX~://**(%%)**// Frequency Band//**
1282
1283 * (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1284 * (% style="color:red" %)** 915**(% style="color:black" %):  valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1285
1286 (% style="color:#4f81bd" %)
1287
1288 (% style="color:blue" %)**//YYY~://**(%%)**// 4G Cellular Option//**
1289
1290 * (% style="color:red" %)** EC25-E**(% style="color:black" %):  EMEA, Korea, Thailand, India.
1291 * (% style="color:red" %)** EC25-A**(% style="color:black" %):  North America/ Rogers/AT&T/T-Mobile.
1292 * (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
1293 * (% style="color:red" %)** EC25-J**(% style="color:black" %):  Japan, DOCOMO/SoftBank/ KDDI
1294
1295 More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
1296
1297
1298 = 13.  Packing Info =
1299
1300 (((
1301
1302
1303 **Package Includes**:
1304
1305 * LG308N or LG08 LoRa Gateway x 1
1306 * Stick Antenna for LoRa RF part. Frequency is one of 433 or 868 or 915Mhz depends the model ordered
1307 * Power Adapter: EU/AU/US type power adapter depends on country to be used
1308 * Packaging with environmental protection paper box
1309 )))
1310
1311 (((
1312
1313
1314 **Dimension and weight**:
1315 )))
1316
1317 * Device Size: 26 x 9 x 8.5 cm
1318 * Weight: 450g
1319 * Package Size: 49 x 19.5 x x 19Package Size: 4912 cm
1320 * Weight: 2.5kg
1321
1322
1323 = 14.  Support =
1324
1325
1326 * Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].
1327 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.
1328 Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.
1329 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to: [[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]
1330
1331
1332 = 15.  Reference =
1333
1334
1335 * Source code for LG08 LoRa Gateway: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]
1336
1337 * OpenWrt official Wiki: [[http:~~/~~/www.openwrt.org/>>url:http://www.openwrt.org/]]
1338
1339 * Firmware: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG308N-OLG308N/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]]
1340
1341 * Hardware Source code: [[https:~~/~~/github.com/dragino/motherboard-hardware/tree/master/LG308N>>url:https://github.com/dragino/motherboard-hardware/tree/master/LG308]]
1342
1343
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0