LG308N - LoRaWAN Gateway User Manual

The LG308N is an open source (% style="color:blue" %)**LoRaWAN Pico Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular network. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.

28

)))

29

30

(((

31

The LG308N uses (% style="color:blue" %)**Semtech packet forwarder** (%%)and fully compatible with LoRaWAN protocol. It includes a (% style="color:blue" %)**SX1302 LoRa concentrator**(%%), which provides 10 programmable parallel demodulation paths.

)))

(((

LG308N has (% style="color:blue" %)**pre-configured standard LoRaWAN frequency bands**(%%) to use for different countries. User can also (% style="color:blue" %)**customized the frequency bands**(%%) to use in their own LoRa network.

)))

(((

LG308N can communicate with ABP LoRaWAN end node without LoRaWAN server. System integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service.

)))

)))

(((

)))

[[image:1657010949218-224.png]]

48

49

50

== 1.2 Specifications ==

51

52

53

(% style="color:#037691" %)**Hardware System:**

(((

Linux Part:

)))

* 400Mhz ar9331 processor

* 64MB RAM

* 16MB Flash

(% style="color:#037691" %)**Interface:**

64

65

* 10M/100M RJ45 Ports x 2

66

* WiFi : 802.11 b/g/n

67

* LoRaWAN Wireless

68

* Power Input: 12 V DC, 2 A

69

* IEEE 802.3 af compliant PoE port (DC 37 ~~ 57 v)

70

* USB 2.0 host connector x 1

71

* Mini-PCI E connector x 1

72

* SX1302 + 2 x SX1250

73

74

(% style="color:#037691" %)**WiFi Spec:**

75

76

* IEEE 802.11 b/g/n

77

* Frequency Band: 2.4 ~~ 2.462GHz

78

* Tx power:

79

** 11n tx power : mcs7/15: 11db mcs0 : 17db

80

** 11b tx power: 18db

81

** 11g 54M tx power: 12db

82

** 11g 6M tx power: 18db

* Wifi Sensitivity

** 11g 54M : -71dbm

** 11n 20M : -67dbm

(% style="color:#037691" %)**LoRa Spec:**

88

89

* Up to -142.5 dBm sensitivity with SX1250 Tx/Rx front-end

90

* 70 dB CW interferer rejection at 1 MHz offset

91

* Able to operate with negative SNR, CCR up to 9dB

92

* Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator

93

* Dual digital TX & RX radio front-end interfaces

94

* 10 programmable parallel demodulation paths

95

* Dynamic data-rate (DDR) adaptation

96

* True antenna diversity or simultaneous dual-band operation

97

98

(% style="color:#037691" %)**Cellular 4G LTE (optional):**

99

100

* Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]

101

* Standard Size SIM Slot

102

* 2 x 4G Sticker Antenna.

103

* Up to 150Mbps downlink and 50Mbps uplink data rates

104

* Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage

105

* MIMO technology meets demands for data rate and link reliability in modem wireless communication systems

== 1.3 Features ==

* Open Source Linux system

111

* Managed by Web GUI, SSH via LAN or WiFi

112

* Emulates 49x LoRa demodulators

113

* LoRaWAN Gateway

114

* 10 programmable parallel demodulation paths

115

116

== 1.4 Hardware System Structure ==

117

118

[[image:1657011152828-178.png]]

119

120

121

== 1.5 LG308N Applications ==

122

123

124

[[image:1657011208596-209.png]]

125

126

127

== 1.6 LED Indicators ==

128

129

LG308N has totally 6 LEDs, They are:

130

131

* **Power LED **[[image:image-20220705165446-1.png||height="21" width="22"]] : This (% style="color:red" %)**LED**(%%) will be **solid on** if the device is properly powered.

132

* **HEART LED **[[image:image-20220705165446-2.png||height="19" width="18"]] : No function yet.

133

* **SYS LED** [[image:image-20220705165446-3.png||height="20" width="19"]] : This** LED** will shows different colors on different state:

134

** (% style="color:red" %)**SOLID**(%%): Device is alive with LoRaWAN server connection.

135

** (% style="color:red" %)**BLINKING**(%%)**:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will (% style="color:red" %)**BLINKING**(%%)** **for several seconds.

136

** (% style="color:red" %)**OFF**(%%): Device doesn't have Internet connection.

137

138

* **ETH LED**[[image:image-20220705165446-4.png||height="19" width="22"]] [[image:image-20220705165446-5.png||height="18" width="20"]] : These two LEDs show the ETH interfaces connection status.

139

* **WiFi LED** [[image:image-20220705165446-6.png||height="19" width="19"]]** **: This LED shows the WiFi interface connection status.

140

141

(% style="color:red" %)**Note: Above LED indication are for firmware version > LG02_LG08~-~-build-v5.3.1584002217-20200312-1639**

(((

(((

)))

)))

= 2. Access and Configure LG308N =

151

152

The LG308N is configured as a WiFi Access Point by default. User can access and configure the DLOS8N after connecting to its WiFi network, or via its Ethernet port.

153

154

155

== 2.1 Find IP address of LG308N ==

156

157

=== 2.1.1 Connect via WiFi ===

158

159

[[image:1657011715859-829.png]]

160

161

162

At the first boot of LG308N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(%%)with password:

163

164

(% style="color:red" %)Note: In latest version firmware, it has been password protected and the password is: dragino+dragino

165

166

[[image:1652413127647-377.png]]

(((

User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the LG308N has the default IP (% style="color:green" %)10.130.1.1

)))

=== 2.1.2 Connect via WAN port with DHCP IP from router ===

176

177

[[image:1657011966663-484.png]]

178

179

(((

180

Alternatively, connect the LG308N** __WAN port__** to your router and LG308N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LG308N. You can also use this IP to connect.

)))

(((

)))

=== 2.1.3 Connect via LAN port with direct connection from PC ===

189

190

[[image:1657012061799-674.png]]

191

192

(((

193

The LG308N __**LAN port**__ is configured as DHCP router by default, user can connect the PC to LAN port and set PC to DHCP mode, it will get IP from LAN port and be able to access to the device. The default IP in LAN port is 10.130.1.1

)))

=== 2.1.4 Connect WiFi with DHCP IP from router ===

199

200

[[image:image-20220705171041-7.png]]

201

202

203

If the LG308N already connect to the router via WiFi, use can use the WiFi IP to connect to LG308N.

=== 2.1.5 Connect via LAN port by fall back ip ===

208

209

The **LAN port** also has a [[fall back ip address>>path:#fallback_ip]] for access if user doesn't connect to uplink router.

== 2.2 Access Configure Web UI ==

**Web Interface**

Open a browser on the PC and type the LG308N ip address (depends on your connect method)

218

219

[[http:~~/~~/10.130.1.1/>>url:http://10.130.1.1/]] (Access via WiFi AP network)

or

http:~/~/IP_ADDRESS or [[http:~~/~~/ IP_ADDRESS:8000>>url:http://192.168.1.xx:8000]]

224

225

226

You will see the login interface of DLOS8N as shown below.

227

228

The account details for Web Login are:

229

230

(% style="color:#4f81bd" %)**User Name: root**

231

232

(% style="color:#4f81bd" %)**Password: dragino**

233

234

[[image:1652414287022-223.png]]

235

236

237

= 3. Typical Network Setup =

== 3.1 Overview ==

(((

LG308N supports flexible network set up for different environment. This section describes the typical network topology can be set in LG308N. The typical network set up includes:

243

)))

244

245

* **WAN Port Internet Mode**

246

* **WiFi Client Mode**

* **WiFi AP Mode**

* **Cellular Mode**

== 3.2 Use WAN port to access Internet ==

252

253

By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N’s WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:

254

255

[[image:1657012559318-672.png]]

256

257

258

== 3.3 Access the Internet as a WiFi Client ==

259

260

In the WiFi Client Mode, LG308N acts as a WiFi client and gets DHCP from an upstream router via WiFi.

261

262

(((

263

The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**

264

)))

265

266

[[image:1657012573321-862.png]]

267

268

(((

269

In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click Save & Apply to connect.

)))

== 3.4 Use built-in 4G modem for internet access ==

275

276

If the LG308N has 3G/4G Cellular modem, user can use it as main internet connection or back up.

277

278

279

First, install the Micro SIM card as below direction

280

281

Second, Power off/ ON LG308N to let it detect the SIM card.

282

283

[[image:image-20220705171836-8.png]]

(((

)))

(((

The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**

)))

(((

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

)))

(((

[[image:image-20220705171919-9.png]]

)))

== 3.5 Check Internet connection ==

307

308

In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.

309

310

* GREEN Tick [[image:1652436675869-206.png||height="14" width="15"]] : This interface has Internet connection.

311

* Yellow Tick [[image:1652436705761-420.png||height="15" width="15"]] : This interface has IP address but don't use it for internet connection.

312

* RED Cross [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn't connected.

313

314

[[image:1657012821329-972.png]]

315

316

317

= 4. Example: Configure as a LoRaWAN gateway =

318

319

LG308N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.

320

321

(((

322

[[image:1657012860422-990.png]]

323

)))

324

325

This chapter describes how to use the LG308N to work with(TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]] ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])

326

327

328

== 4.1 Create a gateway in TTN V3 Server ==

329

330

331

(% style="color:#4f81bd" %)**Step 1: Get a Unique gateway ID.**

332

333

(((

334

Every LG308N has a unique gateway id. The ID can be found at LoRaWAN page:

)))

(((

[[image:1657013108723-531.png]]

)))

The example gateway id is: (% style="color:green" %)**a840411e96744154**

344

345

346

(% style="color:#4f81bd" %)**Step 2: Sign up a user account in TTN server**

347

348

[[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]

349

350

[[image:1652422127479-258.png||height="346" width="738"]]

351

352

353

(% style="color:#4f81bd" %)**Step 3: Choose the TTNv3 Cluster Picker**

354

355

(((

356

[[image:1652422142236-792.png||height="356" width="737"]]

357

)))

358

359

(% style="color:red" %)**Note: Choose the cluster corresponds to a specific Gateway server address**

360

361

362

* Europe 1 (% style="color:red" %)**corresponding Gateway server address:** (% style="color:black" %)eu1.cloud.thethings.network

363

* North America 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)nam1.cloud.thethings.network

364

* Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network

365

* Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**

366

367

368

(% style="color:#4f81bd" %)**Step 4: Create a Gateway**

369

370

[[image:1652422440891-514.png||height="360" width="747"]]

371

372

Click the Gateway icon and then click Add gateway.

373

374

Open the following page:

375

376

[[image:1652422470352-518.png||height="391" width="716"]]

377

378

379

[[image:1652422479876-297.png||height="398" width="729"]]

(((

(% style="color:red" %)**Notice: **Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.

384

)))

385

386

After creating the gateway, you can see the gateway info, as below.

387

388

[[image:1652422509034-682.png||height="299" width="739"]]

389

390

391

== 4.2 Configure DLOS8N to connect to TTN v3 ==

392

393

(((

394

You can now configure the LG308N to let it connect to TTN network V3.

)))

(((

Make sure your LG308N has a working Internet Connection first.

)))

(((

Choose the right server provider and click (% style="color:#4f81bd" %)**Save&Apply**

403

)))

404

405

[[image:1652422624783-580.png||height="327" width="729"]]

406

407

(% style="color:red" %)**Note: **The server address must match the Gateway server address you choose in TTN V3.

408

409

410

In the home page, we can see the LoRaWAN connection is ready now.

411

412

[[image:1657014479765-850.png]]

413

414

415

In TTN v3 portal, we can also see the gateway is connected.

416

417

[[image:1652422703020-955.png||height="343" width="730"]]

418

419

420

== 4.3 Configure frequency ==

421

422

We also need to set the frequency plan in LG308N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.

423

424

425

[[image:1652422737399-529.png||height="362" width="737"]]

426

427

428

In logread page, user can check the frequency actually used.

429

430

[[image:1652422763536-750.png||height="514" width="730"]]

431

432

433

== 4.4 Add a LoRaWAN End Device ==

434

435

(((

436

This section shows how to add a LoRaWAN End device to a LoRaWAN network and see the data from TTN web site.

)))

(((

We use [[LT-22222-L>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/156-lt-22222-l.html]] IO Controller as a reference device - the setup for other LoRaWAN devices will be similar.

441

)))

442

443

[[image:1652422794767-871.png]]

444

445

(((

446

(% style="color:#4f81bd" %)**Step 1**: (% style="color:black" %)Create a Device definition in TTN v3 with the OTAA keys from the example LT-22222-L IO Controller device.

)))

(((

Three codes are required to define the device in TTN v3:

451

)))

452

453

* DEV EUI - Unique ID code for a particular device.

454

* APP EUI - ID code for an Application defined in TTN v3.

455

* APP Key - Unique key to secure communications with a particular device.

(((

A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.

461

)))

462

463

[[image:1652422840936-838.png]]

(((

(% style="color:red" %)Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands. Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.

)))

(((

For the TTN v3 server, you can use the codes set in the device as in the following example.

)))

(((

Select **Add Application** to open the screen below.

478

)))

479

480

[[image:1657014671459-433.png]]

481

482

483

Open the **Application **select** Add end device**

484

485

486

Start Register the end device

487

488

[[image:1652422975885-591.png||height="359" width="726"]]

489

490

(((

491

Select OTAA activation mode

)))

(((

The LoRaWAN version for your device should be provided by the manufacturer in a datasheet as LoRaWAN version or LoRaWAN specification. The most commonly used LoRaWAN versions are v1.0.2 and v1.0.3.

498

)))

499

500

[[image:1652422998005-968.png||height="352" width="744"]]

501

502

First, input the End device ID, AppEUI and DevEUI.

503

504

505

[[image:1652423022781-339.png||height="365" width="741"]]

506

507

Secondly, choose the corresponding frequency and LoRaWAN class capabilities.

508

509

510

[[image:1652423046741-467.png||height="355" width="736"]]

511

512

(((

513

Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.

)))

(((

(% style="color:#4f81bd" %)**Step 2**: (% style="color:black" %)Power on LT-22222-L device and it will automatically join the TTN network. After joining successfully, it will start to upload messages to the TTN v3. Select the Live data tab and you will see the data appearing in the panel.

)))

(((

(% style="color:red" %)Note that it may take some time for the device data to appear in the TTN v3 display.

524

)))

525

526

[[image:1652423277549-324.png||height="273" width="745"]]

527

528

529

= 5. Web Configure Pages =

== 5.1 Home ==

Shows the system running status.

534

535

[[image:1657014949846-507.png]]

536

537

538

== 5.2 LoRa Settings ==

539

540

=== 5.2.1 LoRa ~-~-> LoRa ===

541

542

(((

543

This page shows the LoRa Radio Settings. There are a set of default frequency band according to LoRaWAN protocol, and user can customized the band* as well.

)))

(((

Different LG308N hardware version can support different frequency range:

548

)))

549

550

* (% style="color:blue" %)**868**(%%): valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

551

* (% style="color:blue" %)**915**(%%): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

552

553

(((

554

After user choose the frequency plan, he can see the actually frequency in used by checking the page **LogRead ~-~-> LoRa Log**

555

)))

556

557

[[image:1652423554776-574.png||height="380" width="740"]]

558

559

Note *: **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**

560

561

562

=== 5.2.2 LoRa ~-~-> ABP Decryption ===

563

564

The LG308N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:

565

566

* No internet connection.

567

* User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).

(((

Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**

573

)))

574

575

[[image:1652423628833-467.png||height="357" width="755"]]

576

577

578

== 5.3 LoRaWAN Settings ==

579

580

=== 5.3.1 LoRaWAN ~-~-> LoRaWAN ===

581

582

This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc

583

584

[[image:1652423628833-467.png||height="357" width="755"]]

585

586

(% style="color:red" %)**Note:**

587

588

~*: User can ignore the latitude and longitude settings here, DLOS8N will use the actually value from GPS module.

589

590

~**: Packet filter is to drop the unwanted LoRaWAN packet, instruction see here:

591

592

**See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**

=== 5.3.2 LoRaWAN ~-~-> Amazon AWS-IoT ===

597

598

[[image:1652428499323-384.png||height="275" width="723"]]

(((

Please see this instruction to know more detail and demo for how to connect to **[[AWS-IoT LoRaWAN Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**

)))

=== 5.3.3 LoRaWAN ~-~-> LORIOT ===

609

610

(((

611

Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]

)))

(((

Instruction: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**

616

)))

617

618

[[image:1652428648903-878.png||height="266" width="731"]]

619

620

621

== 5.4 MQTT Settings ==

622

623

If end nodes works in ABP mode, user can configure LG308N to transfer the data to MQTT broker,

624

625

Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**

626

627

628

[[image:1652428705046-212.png||height="417" width="733"]]

== 5.5 System ==

=== 5.5.1 System ~-~-> System Overview ===

635

636

Shows the system info:

637

638

[[image:1652428773760-580.png||height="408" width="728"]]

=== 5.5.2 System ~-~-> General ( login settings) ===

643

644

[[image:1652428861256-300.png||height="354" width="724"]]

645

646

(((

647

**__System Password:__**

)))

(((

There are two login for DLOS8: (% style="color:#4f81bd" %)root /dragino (% style="color:black" %)or (% style="color:#4f81bd" %)admin /dragino. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.

)))

(((

This page can be used to set the password for them.

)))

(((

**__Timezone: __**Set device timezone.

)))

(((

**__Port forwarding: __**Enable/Disable the HTTP and SSH access via WAN interface.

)))

=== 5.5.3 System ~-~-> Network ===

670

671

[[image:1652429149053-824.png||height="467" width="725"]]

672

673

(((

674

**__LAN Settings: __**When the LG308N has the AP enable, LAN settings specify the network info for LG308N's own network.

)))

(((

__**WAN Settings: **__Setting for LG308N WAN port

)))

(((

__**WiFi Settings: **__Setting for LG308N WiFi IP when use it as WiFi Client

)))

=== 5.5.4 System ~-~-> WiFi ===

688

689

LG308N WiFi Settings.

690

691

[[image:1652429430767-921.png||height="367" width="723"]]

=== 5.5.5 System ~-~-> Cellular ===

696

697

While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.

698

699

[[image:1652429309615-825.png||height="320" width="732"]]

700

701

(% style="color:red" %)Note *: For LG308N which doesn't have the cellular module, this page will shows Cellular not detected.

=== 5.5.6 System ~-~-> Network Status ===

706

707

[[image:1652429486609-208.png||height="415" width="728"]]

=== 5.5.7 System ~-~-> Remote Mgnt & Auto Provision ===

712

713

Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:

714

715

[[image:1652429518191-846.png||height="332" width="733"]]

716

717

[[image:1652429527544-247.png||height="327" width="724"]]

718

719

[[image:1652429537849-154.png||height="339" width="722"]]

720

721

Please see this document for detail:

722

723

[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG308N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]

(((

)))

R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Remote Access Gateway.WebHome]]**

731

732

[[image:1652429624400-864.png||height="432" width="716"]]

=== 5.5.8 System ~-~-> Firmware Upgrade ===

737

738

We keep improving the DLOS8N Linux side firmware for new features and bug fixes. Below are the links for reference.

739

740

* **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],

741

742

( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )

743

744

745

* **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].

746

747

( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )

(((

The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.

)))

(((

(% style="color:green" %)**Web~-~-> System~-~-> Firmware Upgrade**

756

)))

757

758

[[image:1652429711145-862.png||height="270" width="737"]]

759

760

Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.

761

762

(% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.

763

764

The system will automatically boot into the new firmware after upgrade.

765

766

[[image:1652429962190-224.png||height="358" width="729"]]

767

768

(% style="color:red" %)**NOTE***(%%): User can also upgrade firmware via Linux console

769

770

SCP the firmware to the system(% style="color:green" %)**/var**(%%)** **directory and then run

771

772

(% style="color:#4f81bd" %)**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**

773

774

(% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.

775

776

777

=== 5.5.9 System ~-~-> Reboot/Reset ===

778

779

[[image:1652430197132-330.png||height="256" width="724"]]

(((

)))

=== 5.5.10 System ~-~-> Package Maintain ===

786

787

[[image:1652430243826-126.png||height="289" width="723"]]

788

789

Place to show what package has installed and possible to upgrade packages.

== 5.6 LogRead ==

=== 5.6.1 LogRead ~-~-> LoRa Log ===

795

796

797

Show the frequency for LoRa Radio and traffics.

798

799

[[image:image-20220615204306-1.png||height="575" width="733"]]

800

801

802

Show the IoT Server Connection State and FWD State

803

804

[[image:image-20220616083933-1.png||height="556" width="729"]]

805

806

DLOS8 can view GPS location in the Logread FWD State

807

808

809

Show the Error logs, RxTxJson lorawan packages, and PULL State

810

811

[[image:image-20220615205416-6.png||height="442" width="884"]]

812

813

814

=== 5.6.2 LogRead ~-~-> System Log ===

Show the system log

[[image:1652430369760-511.png||height="373" width="730"]]

= 6. More features =

== 6.1 More instructions ==

823

824

[[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)

= 7. Linux System =

The DLOS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.

830

831

832

== 7.1 SSH Access for Linux console ==

833

834

User can access the Linux console via the SSH protocol. Make sure your PC and the DLOS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.

835

836

IP address: IP address of DLOS8N

837

838

Port: 22 (via WiFi AP mode) or 2222 (via WAN Interface)

839

840

User Name: (% style="color:green" %)**root**

841

842

Password: (% style="color:green" %)**dragino** (% style="color:black" %)(default)

843

844

After logging in, you will be in the Linux console and can enter commands as shown below.

845

846

[[image:1652431588565-830.png]]

847

848

The “(% class="mark" %)**logread -f**(%%)” command can be used to debug how system runs.

849

850

[[image:1652431609193-637.png||height="214" width="732"]]

851

852

853

== 7.2 Edit and Transfer files ==

854

855

(((

856

The DLOS8N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.

)))

(((

In Windows, one of the easiest methods is using the [[WinSCP>>url:https://winscp.net/eng/index.php]] utility.

)))

(((

After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the DLOS8N, or edit the files directly in the windows.

)))

(((

Screenshot is as below:

869

)))

870

871

[[image:1652431650755-450.png]]

872

873

874

== 7.3 File System ==

875

876

(((

877

The DLOS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.

)))

(((

The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the DLOS8N flash.

)))

(((

You can use an external USB flash memory device to extend the size of flash memory for storage.

)))

== 7.4 Package maintenance system ==

890

891

DLOS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure DLOS8N to use **//iperf //**.

892

893

(((

894

Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])

)))

(((

**In Linux Console run:**

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg update** (% style="color:black" %)~/~/ to get the latest packages list

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg list** (% style="color:black" %) ~/~/shows the available packages

)))

(((

(% style="color:green" %)**root@dragino-169d30:~~# opkg install iperf ** (% style="color:black" %)~/~/ install iperf

911

)))

912

913

The system will automatically install the required packages as shown below.

(((

(% style="background-color:#dcdcdc" %)//root@dragino-169d30:/etc/opkg# opkg install iperf//

)))

(((

(% style="background-color:#dcdcdc" %)//Installing iperf (2.0.12-1) to root…//

)))

(((

(% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/iperf_2.0.12-1_mips_24kc.ipk]]

)))

(((

(% style="background-color:#dcdcdc" %)//Installing uclibcxx (0.2.4-3) to root…//

)))

(((

(% style="background-color:#dcdcdc" %)//Downloading //[[(% style="background-color: rgb(220, 220, 220); background-color: rgb(220, 220, 220)" %)//http:~~/~~/downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk//>>url:http://downloads.openwrt.org/snapshots/packages/mips_24kc/base/uclibcxx_0.2.4-3_mips_24kc.ipk]]

)))

(((

(% style="background-color:#dcdcdc" %)//Configuring uclibcxx.//

)))

(((

(% style="background-color:#dcdcdc" %)//Configuring iperf.//

942

)))

943

944

= 8. Upgrade Linux Firmware =

= 9. FAQ =

== 9.1 How can I configure for a customized frequency band? ==

950

951

(((

952

See below link for how to customize frequency band: **[[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**

)))

(((

)))

== 9.2 Can I connect DLOS8N to LORIOT? ==

960

961

Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**

962

963

964

== 9.3 Can I make my own firmware for the gateway, where can I find the source code? ==

965

966

(((

967

Yes, You can make your own firmware for the DLOS8N for branding purposes or to add customized applications.

)))

(((

The source code and compile instructions can be found at: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]

)))

== 9.4 Can I use 868Mhz version for 915Mhz bands? ==

976

977

It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.

978

979

980

= 10. Trouble Shooting =

981

982

== 10.1 I get kernel error when install new package, how to fix? ==

983

984

In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:

985

986

(% style="background-color:yellow" %)root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk

987

988

(% style="background-color:yellow" %)Installing kmod-dragino2-si3217x (3.10.49+0.2-1) to root…

989

990

(% style="background-color:yellow" %)Collected errors:

991

992

(% style="background-color:yellow" %)* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-dragino2-si3217x:

993

994

(% style="background-color:yellow" %)* kernel (= 3.10.49-1-4917516478a753314254643facdf360a) *

995

996

(% style="background-color:yellow" %)* opkg_install_cmd: Cannot install package kmod-dragino2-si3217x.

997

998

(((

999

In this case, you can use the –force-depends option to install such package as long as the actual kernel version is the same.

1000

)))

1001

1002

(% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends

1003

1004

1005

== 10.2 How to recover the DLOS8N if the firmware crashes ==

1006

1007

(((

1008

Please follow this instruction to recover your gateway: **[[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]**

)))

(((

)))

== 10.3 I configured DLOS8N for WiFi access and lost its IP. What to do now? ==

1016

1017

[[image:1652435238615-272.png||height="247" width="727"]]

1018

1019

(((

1020

The DLOS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access DLOS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.

1021

)))

1022

1023

(% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.

1024

1025

1026

Steps to connect via fall back IP:

1027

1028

~1. Connect PC’s Ethernet port to DLOS8N’s WAN port

1029

1030

2. Configure PC’s Ethernet port has

1031

IP: 172.31.255.253 and

1032

Netmask: 255.255.255.252

As below photo:

[[image:1652435256286-879.png]]

1037

1038

3. In the PC, use IP address 172.31.255.254 to access the DLOS8N via Web or Console.

1039

1040

Please note the latest firmware uses port 8000 for http and 2222 for ssh access.

= 11. Order Info =

(% style="color:#4f81bd" %) **//PART: DLOS8N-XXX-YYY//: **

1046

1047

(% style="color:#4f81bd" %) **//XXX: Frequency Band//**

1048

1049

* (% style="color:#4f81bd" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.

1050

* (% style="color:#4f81bd" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920

1051

1052

(% style="color:#4f81bd" %) **//YYY: 4G Cellular Option//**

1053

1054

* (% style="color:#4f81bd" %)** E**(% style="color:black" %): EMEA, Korea, Thailand, India.

1055

* (% style="color:#4f81bd" %)** A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.

1056

* (% style="color:#4f81bd" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan

1057

* (% style="color:#4f81bd" %)** J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI

1058

1059

More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].

= 12. Packing Info =

(((

**Package Includes**:

1066

)))

1067

1068

* DLOS8N LoRaWAN Gateway x 1

1069

* Stick Antenna for LoRa RF part. Frequency is one of 470 or 868 or 915Mhz depends the model ordered

1070

* Packaging with environmental protection paper box

1071

1072

(((

1073

**Dimension and weight**:

1074

)))

1075

1076

* Device Size: 26 x 9 x 8.5 cm

1077

* Weight: 450g

1078

* Package Size: 49 x 19.5 x x 19Package Size: 4912 cm

* Weight: 2.5kg

= 13. Support =

* Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].

1084

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.

1085

Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.

1086

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to:[[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]

Wiki source code of LG308N - LoRaWAN Gateway User Manual

Applications

Navigation