Skip to Content
Last modified by Kilight Cao on 2025/02/07 08:57
From version 127.12
edited by Xiaoling
on 2022/07/29 16:37
Change comment: There is no comment for this version
To version 149.1
edited by Kilight Cao
on 2024/05/17 10:21
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LG308N - LoRaWAN Gateway User Manual
1 +LG308N -- LoRaWAN Gateway User Manual
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.Kilight
Content
... ... @@ -4,7 +4,7 @@
4 4  
5 5  
6 6  
7 -**Table of Contents：**
7 +**Table of Contents:**
8 8  
9 9  {{toc/}}
10 10  
... ... @@ -15,16 +15,11 @@
15 15  
16 16  
17 17  
18 -
19 -
20 -
21 -
22 22  = 1.  Introduction =
23 23  
20 +== (% data-sider-select-id="b56f45fb-88b0-4b64-98a2-012c4c56800e" %)1.1  What is the LG308N(%%) ==
24 24  
25 -== 1.1  What is the LG308N ==
26 26  
27 -
28 28  (((
29 29  (((
30 30  The LG308N is an open source (% style="color:blue" %)**LoRaWAN Pico Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via WiFi, Ethernet, 3G or 4G cellular network. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates.
... ... @@ -50,7 +50,6 @@
50 50  [[image:1657010949218-224.png]]
51 51  
52 52  
53 -
54 54  == 1.2  Specifications ==
55 55  
56 56  
... ... @@ -64,8 +64,6 @@
64 64  * 64MB RAM
65 65  * 16MB Flash
66 66  
67 -
68 -
69 69  (% style="color:#037691" %)**Interface:**
70 70  
71 71  * 10M/100M RJ45 Ports x 2
... ... @@ -77,8 +77,6 @@
77 77  * Mini-PCI E connector x 1
78 78  * SX1302 + 2 x SX1250
79 79  
80 -
81 -
82 82  (% style="color:#037691" %)**WiFi Spec:**
83 83  
84 84  * IEEE 802.11 b/g/n
... ... @@ -92,21 +92,17 @@
92 92  ** 11g 54M : -71dbm
93 93  ** 11n 20M : -67dbm
94 94  
95 -
96 -
97 97  (% style="color:#037691" %)**LoRa Spec:**
98 98  
99 99  * Up to -142.5 dBm sensitivity with SX1250 Tx/Rx front-end
100 100  * 70 dB CW interferer rejection at 1 MHz offset
101 101  * Able to operate with negative SNR, CCR up to 9dB
102 -* Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator
90 +* 8 x 8 channels LoRa packet detectors,8 x SF5-SF12 LoRa demodulators,8 x SF5-SF10 LoRa demodulators,125/250/500 kHz LoRa demodulator and 1 x (G)FSK demodulator
103 103  * Dual digital TX & RX radio front-end interfaces
104 104  * 10 programmable parallel demodulation paths
105 105  * Dynamic data-rate (DDR) adaptation
106 106  * True antenna diversity or simultaneous dual-band operation
107 107  
108 -
109 -
110 110  (% style="color:#037691" %)**Cellular 4G LTE (optional):**
111 111  
112 112  * Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
... ... @@ -116,9 +116,6 @@
116 116  * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
117 117  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
118 118  
119 -
120 -
121 -
122 122  == 1.3  Features ==
123 123  
124 124  
... ... @@ -128,16 +128,12 @@
128 128  * LoRaWAN Gateway
129 129  * 10 programmable parallel demodulation paths
130 130  
131 -
132 -
133 -
134 134  == 1.4  Hardware System Structure ==
135 135  
136 136  
137 -[[image:1657011152828-178.png]]
117 +[[image:image-20221101103113-1.png]]
138 138  
139 139  
140 -
141 141  == 1.5  LG308N Applications ==
142 142  
143 143  
... ... @@ -144,7 +144,6 @@
144 144  [[image:1657011208596-209.png]]
145 145  
146 146  
147 -
148 148  == 1.6  LED Indicators ==
149 149  
150 150  
... ... @@ -165,12 +165,22 @@
165 165  )))
166 166  
167 167  
168 -(((
169 -(((
170 -
171 -)))
172 -)))
146 +== 1.7 Button Instruction ==
173 173  
148 +
149 +LG308N has a black toggle button, which is:
150 +
151 +
152 +(% style="color:blue" %)**//➢ //Long press 4-5s:                     **(%%)the gateway will reload the Network and Initialize wifi configuration
153 +
154 + **LED status: ** SYS LED will BLINKING RED Until the reload is finished.
155 +
156 +
157 +(% style="color:blue" %)**➢ Long press more than 30s:    **(%%)the gateway will restart and restore factory settings.
158 +
159 + **LED status: ** When the user releases the button, the LED will TURN OFF.
160 +
161 +
174 174  = 2.  Access and Configure LG308N =
175 175  
176 176  
... ... @@ -177,17 +177,17 @@
177 177  The LG308N is configured as a WiFi Access Point by default. User can access and configure the LG308N after connecting to its WiFi network, or via its Ethernet port.
178 178  
179 179  
180 -
181 181  == 2.1  Find IP address of LG308N ==
182 182  
183 -
184 184  === 2.1.1  Connect via WiFi ===
185 185  
172 +
186 186  [[image:1657011715859-829.png]]
187 187  
188 188  
189 189  At the first boot of LG308N, it will auto generate a WiFi network called (% style="color:green" %)**//dragino-xxxxxx //**(%%)with password:
190 190  
178 +
191 191  (% style="color:red" %)**Note: In latest version firmware, it has been password protected and the password is:  **(% style="background-color:yellow" %)**dragino+dragino**
192 192  
193 193  
... ... @@ -197,7 +197,6 @@
197 197  (((
198 198  User can use a PC to connect to this WiFi network. The PC will get an IP address 10.130.1.xxx and the LG308N has the default IP (% style="color:green" %)**10.130.1.1**
199 199  
200 -
201 201  
202 202  )))
203 203  
... ... @@ -206,12 +206,10 @@
206 206  
207 207  [[image:1657011966663-484.png]]
208 208  
196 +
209 209  (((
210 210  Alternatively, connect the LG308N** __WAN port__** to your router and LG308N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LG308N. You can also use this IP to connect.
211 -)))
212 212  
213 -
214 -(((
215 215  
216 216  )))
217 217  
... ... @@ -220,12 +220,12 @@
220 220  
221 221  [[image:1657012061799-674.png]]
222 222  
208 +
223 223  (((
224 224  The LG308N __**LAN port**__ is configured as DHCP router by default, user can connect the PC to LAN port and set PC to DHCP mode, it will get IP from LAN port and be able to access to the device. The default IP in LAN port is 10.130.1.1
225 225  )))
226 226  
227 227  
228 -
229 229  === 2.1.4  Connect WiFi with DHCP IP from router ===
230 230  
231 231  
... ... @@ -235,14 +235,12 @@
235 235  If the LG308N already connect to the router via WiFi, use can use the WiFi IP to connect to LG308N.
236 236  
237 237  
238 -
239 239  === 2.1.5  Connect via LAN port by fall back ip ===
240 240  
241 241  
242 -The **LAN port** also has a [[fall back ip address>>path:#fallback_ip]] for access if user doesn't connect to uplink router.
226 +The **LAN port** also has a [[fall back ip address>>||anchor="H11.3A0IconfiguredLG308NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router.
243 243  
244 244  
245 -
246 246  == 2.2  Access Configure Web UI ==
247 247  
248 248  
... ... @@ -254,7 +254,7 @@
254 254  
255 255  or
256 256  
257 -http:~/~/IP_ADDRESS or [[http:~~/~~/ IP_ADDRESS:8000>>url:http://192.168.1.xx:8000]]
240 +http:~/~/IP_ADDRESS or http:~/~/ IP_ADDRESS:8000
258 258  
259 259  
260 260  You will see the login interface of DLOS8N as shown below.
... ... @@ -265,13 +265,12 @@
265 265  
266 266  (% style="color:#4f81bd" %)**Password:   dragino**
267 267  
251 +
268 268  [[image:1652414287022-223.png]]
269 269  
270 270  
271 -
272 272  = 3.  Typical Network Setup =
273 273  
274 -
275 275  == 3.1  Overview ==
276 276  
277 277  
... ... @@ -284,18 +284,15 @@
284 284  * **WiFi AP Mode**
285 285  * **Cellular Mode**
286 286  
287 -
288 -
289 -
290 290  == 3.2  Use WAN port to access Internet ==
291 291  
292 292  
293 293  By default, the LG308N is set to use the WAN port to connect to an upstream network. When you connect the LG308N's WAN port to an upstream router, LG308N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
294 294  
274 +
295 295  [[image:1657012559318-672.png]]
296 296  
297 297  
298 -
299 299  == 3.3  Access the Internet as a WiFi Client ==
300 300  
301 301  
... ... @@ -305,12 +305,11 @@
305 305  The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**
306 306  )))
307 307  
308 -[[image:1657012573321-862.png]]
287 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916142159-25.png?rev=1.1||alt="image-20220916142159-25.png" height="398" width="859"]]
309 309  
310 310  (((
311 311  In the WiFi Survey Choose the WiFi AP, and input the Passphrase then click(% style="color:blue" %)** Save & Apply**(%%) to connect.
312 312  
313 -
314 314  
315 315  )))
316 316  
... ... @@ -327,7 +327,6 @@
327 327  [[image:image-20220705171836-8.png]]
328 328  
329 329  
330 -
331 331  (((
332 332  The set up page is (% style="color:#4f81bd" %)**System ~-~-> Cellular**
333 333  )))
... ... @@ -339,11 +339,10 @@
339 339  )))
340 340  
341 341  (((
342 -[[image:image-20220705171919-9.png]]
319 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916141840-23.png?rev=1.1||alt="image-20220916141840-23.png" height="356" width="868"]]
343 343  )))
344 344  
345 345  
346 -
347 347  == 3.5  Check Internet connection ==
348 348  
349 349  
... ... @@ -356,30 +356,35 @@
356 356  [[image:1657012821329-972.png]]
357 357  
358 358  
359 -
360 360  = 4.  Example: Configure as a LoRaWAN gateway =
361 361  
362 362  
363 363  LG308N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.
364 364  
340 +
365 365  (((
366 366  [[image:1657012860422-990.png]]
343 +
344 +
367 367  )))
368 368  
369 369  This chapter describes how to use the LG308N to work with(TTN v3)[[ LoRaWAN Server>>url:https://www.thethingsnetwork.org/]]  ([[www.thethingsnetwork.org>>url:http://www.thethingsnetwork.org/]])
370 370  
371 371  
372 -
373 373  == 4.1  Create a gateway in TTN V3 Server ==
374 374  
375 375  
376 376  (((
377 377  (% style="color:blue" %)**Step 1: Get a Unique gateway ID.**
355 +
356 +
378 378  )))
379 379  
380 380  (((
381 381  (((
382 382  Every LG308N has a unique gateway id. The ID can be found at LoRaWAN page:
362 +
363 +
383 383  )))
384 384  )))
385 385  
... ... @@ -395,8 +395,10 @@
395 395  
396 396  (% style="color:blue" %)**Step 2: Sign up a user account in TTN server**
397 397  
398 -[[**https:~~/~~/account.thethingsnetwork.org/register**>>url:https://account.thethingsnetwork.org/register]]
399 399  
380 +[[**https:~~/~~/account.thethingsnetwork.org/register**>>https://id.thethingsnetwork.org/]]
381 +
382 +
400 400  [[image:1652422127479-258.png||height="346" width="738"]]
401 401  
402 402  
... ... @@ -403,6 +403,7 @@
403 403  
404 404  (% style="color:blue" %)**Step 3: Choose the TTNv3 Cluster Picker**
405 405  
389 +
406 406  (((
407 407  [[image:1652422142236-792.png||height="356" width="737"]]
408 408  
... ... @@ -417,13 +417,14 @@
417 417  * Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network
418 418  * Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**
419 419  
420 -
421 421  (% style="color:blue" %)**Step 4: Create a Gateway**
422 422  
406 +
423 423  [[image:1652422440891-514.png||height="360" width="747"]]
424 424  
425 425  Click the Gateway icon and then click Add gateway.
426 426  
411 +
427 427  Open the following page:
428 428  
429 429   [[image:1652422470352-518.png||height="391" width="716"]]
... ... @@ -440,10 +440,9 @@
440 440  
441 441  After creating the gateway, you can see the gateway info, as below.
442 442  
428 +
443 443  [[image:1652422509034-682.png||height="299" width="739"]]
444 444  
445 -
446 -
447 447  == 4.2  Configure LG308N to connect to TTN v3 ==
448 448  
449 449  
... ... @@ -456,7 +456,7 @@
456 456  )))
457 457  
458 458  (((
459 -Choose the right server provider and click (% style="color:blue" %)**Save&Apply**
443 +Choose the right server provider and click (% style="color:blue" %)**Save&Apply.**
460 460  
461 461  
462 462  )))
... ... @@ -469,15 +469,17 @@
469 469  
470 470  In the home page, we can see the LoRaWAN connection is ready now.
471 471  
472 -[[image:1657014479765-850.png]]
473 473  
457 +[[image:image-20220916171413-2.png]]
474 474  
459 +
460 +
475 475  In TTN v3 portal, we can also see the gateway is connected.
476 476  
463 +
477 477  [[image:1652422703020-955.png||height="343" width="730"]]
478 478  
479 479  
480 -
481 481  == 4.3  Configure frequency ==
482 482  
483 483  
... ... @@ -492,7 +492,6 @@
492 492   [[image:1652422763536-750.png||height="514" width="730"]]
493 493  
494 494  
495 -
496 496  == 4.4  Add a LoRaWAN End Device ==
497 497  
498 498  
... ... @@ -522,13 +522,15 @@
522 522  
523 523  
524 524  A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.
510 +
511 +
525 525  )))
526 526  
527 -[[image:1652422840936-838.png]]
514 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20230426083319-1.png?width=556&height=258&rev=1.1||alt="image-20230426083319-1.png"]]
528 528  
529 529  
530 530  (((
531 -(% style="color:red" %)Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands.  Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.
518 +(% style="color:red" %)**Note: You may be able to change these codes in a device by using a configuration facility on the device e.g. the LT-22222 uses a serial port access and a series of AT commands.  Changing the codes may be necessary in the case where you have to use codes assigned by a LoRa WAN server.**
532 532  
533 533  
534 534  )))
... ... @@ -594,22 +594,19 @@
594 594  [[image:1652423277549-324.png||height="273" width="745"]]
595 595  
596 596  
597 -
598 598  = 5.  Web Configure Pages =
599 599  
600 -
601 601  == 5.1  Home ==
602 602  
603 603  
604 604  Shows the system running status.
605 605  
591 +
606 606  [[image:1657014949846-507.png]]
607 607  
608 608  
609 -
610 610  == 5.2  LoRa Settings ==
611 611  
612 -
613 613  === 5.2.1  LoRa ~-~-> LoRa ===
614 614  
615 615  
... ... @@ -626,14 +626,16 @@
626 626  
627 627  (((
628 628  After user choose the frequency plan, he can see the actually frequency in used by checking the page (% style="color:blue" %)**LogRead ~-~-> LoRa Log**
613 +
614 +
629 629  )))
630 630  
631 -[[image:1652423554776-574.png||height="380" width="740"]]
617 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LG308N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1652422737399-529.png?rev=1.1||alt="1652422737399-529.png"]]
632 632  
619 +
633 633  (% style="color:red" %)**Note *: [[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
634 634  
635 635  
636 -
637 637  === 5.2.2  LoRa ~-~-> ABP Decryption ===
638 638  
639 639  
... ... @@ -646,23 +646,24 @@
646 646  
647 647  
648 648  Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**
635 +
636 +
649 649  )))
650 650  
651 -[[image:1652423628833-467.png||height="357" width="755"]]
639 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916114346-7.png?rev=1.1||alt="image-20220916114346-7.png" height="359" width="876"]]
652 652  
653 653  
654 -
655 655  == 5.3  LoRaWAN Settings ==
656 656  
657 -
658 658  === 5.3.1  LoRaWAN ~-~-> LoRaWAN ===
659 659  
660 660  
661 -This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc
647 +This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc.
662 662  
663 -[[image:1652423628833-467.png||height="357" width="755"]]
664 664  
650 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916114929-8.png?rev=1.1||alt="image-20220916114929-8.png" height="707" width="860"]]
665 665  
652 +
666 666  (% style="color:red" %)**Note:**
667 667  
668 668  ~*: User can ignore the latitude and longitude settings here, LG308N will use the actually value from GPS module.
... ... @@ -672,17 +672,27 @@
672 672  **See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**
673 673  
674 674  
662 +=== 5.3.2  LoRaWAN ~-~-> LoRaWAN ~-~- Basic Station ===
675 675  
676 -=== 5.3.2  LoRaWAN ~-~-> Amazon AWS-IoT ===
677 677  
665 +[[image:image-20230406173729-1.png]]
678 678  
679 -[[image:1652428499323-384.png||height="275" width="723"]]
680 680  
668 +The basic station mode support **TTN/AWS/Chirpstack/ThingPark/Senet** Platform.
681 681  
682 -(((
683 -Please see this instruction to know more detail and demo for how to connect to **[[AWS-IoT LoRaWAN Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**
670 +Instruction:
684 684  
672 + [[The Thing Network>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20TTN/#H3.A0GatewayRegistrationforBasicsStation]]      
685 685  
674 + [[AWS-IoT LoRaWAN Core>>url:http://wiki.dragino.com/xwiki/bin/view/Main/AWS%20IoT%20Core%20for%20LoRaWAN/]]
675 +
676 + [[Chirpstack>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H3.A0GatewayRegistrationforBasicsStation]]
677 +
678 + ThingPark
679 +
680 + [[Senet>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Connection%20to%20Senet/#H3.A0SemtechBasicStation]]
681 +
682 +(((
686 686  
687 687  )))
688 688  
... ... @@ -695,12 +695,13 @@
695 695  
696 696  (((
697 697  Instruction: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
695 +
696 +
698 698  )))
699 699  
700 -[[image:1652428648903-878.png||height="266" width="731"]]
699 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916115143-9.png?rev=1.1||alt="image-20220916115143-9.png" height="316" width="864"]](% style="display:none" %)
701 701  
702 702  
703 -
704 704  == 5.4  MQTT Settings ==
705 705  
706 706  
... ... @@ -716,98 +716,117 @@
716 716  [[image:1652428705046-212.png||height="417" width="733"]]
717 717  
718 718  
717 +== 5.5  Network ==
719 719  
720 -== 5.5  System ==
719 +=== 5.5.1  Network ~-~-> Network Status ===
721 721  
721 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419143226-2.png?width=950&height=742&rev=1.1||alt="image-20240419143226-2.png"]]
722 722  
723 -=== 5.5.1  System ~-~-> System Overview ===
724 724  
724 +=== 5.5.2  Network ~-~-> Network ===
725 725  
726 -Shows the system info:
727 727  
728 -[[image:1652428773760-580.png||height="408" width="728"]]
727 +(% data-sider-select-id="cddf8b4f-5a22-42d2-bdd8-8ee8180a1f07" %)
728 +**__LAN Settings:    __**When the LG308N has the AP enable, LAN settings specify the network info for LG308N's own network.
729 729  
730 +(% data-sider-select-id="b4859c0c-d733-4fa4-bbc8-509d985342cc" %)
731 +__**WAN Settings:  **__Setting for LG308N WAN port
730 730  
733 +(% data-sider-select-id="a653ed2d-c570-4cfa-9689-27fea7b5f581" %)
734 +__**WiFi Settings:  **__** **Setting for LG308N WiFi IP when use it as WiFi Client
731 731  
732 -=== 5.5.2  System ~-~-> General ( login settings) ===
736 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419143347-3.png?rev=1.1||alt="image-20240419143347-3.png"]]
733 733  
734 734  
735 -[[image:1652428861256-300.png||height="354" width="724"]]
739 +=== 5.5.3  Network ~-~-> WiFi ===
736 736  
737 -(((
738 -(% style="color:#037691" %)**__System Password:__**
739 -)))
740 740  
741 -(((
742 -There are two login for DLOS8: (% style="color:#4f81bd" %)**root /dragino** (% style="color:black" %)or (% style="color:#4f81bd" %)**admin /dragino**. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
743 -)))
742 +(% data-sider-select-id="005f89b3-ae2e-410c-b2ac-db80867d5660" %)
743 +LG308N WiFi Settings.
744 744  
745 -(((
746 -This page can be used to set the password for them.
747 -)))
745 +(% data-sider-select-id="005f89b3-ae2e-410c-b2ac-db80867d5660" %)
746 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419143504-4.png?width=946&height=500&rev=1.1||alt="image-20240419143504-4.png"]]
748 748  
749 -(((
750 -(% style="color:#037691" %)**__Timezone: __**(%%)Set device timezone.
751 -)))
752 752  
753 -(((
754 -(% style="color:#037691" %)**__Port forwarding: __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.
749 +=== 5.5.4  Network ~-~-> Cellular ===
755 755  
751 +While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
756 756  
757 -
758 -)))
753 +(% data-sider-select-id="005f89b3-ae2e-410c-b2ac-db80867d5660" %)
754 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/1657155507672-204.png?rev=1.1||alt="1657155507672-204.png"]]
759 759  
760 -=== 5.5.3  System ~-~-> Network ===
756 +(% data-sider-select-id="005f89b3-ae2e-410c-b2ac-db80867d5660" %)
757 +(% data-sider-select-id="262b1aeb-7601-4231-ba98-63f35bcd6775" %)**Note *: For LG308N which doesn't have the cellular module, this page will shows Cellular not detected.**
761 761  
762 762  
763 -[[image:1652429149053-824.png||height="467" width="725"]]
764 764  
761 +== (% data-sider-select-id="c723b2da-a166-48cd-ab9e-3632fd95e945" %)5.6  System(%%) ==
765 765  
766 -(((
767 -(% style="color:#037691" %)**__LAN Settings:  __**(%%)When the LG308N has the AP enable, LAN settings specify the network info for LG308N's own network.
768 -)))
763 +=== (% data-sider-select-id="573ebcc8-61e5-4f99-8729-b580f3f3fe27" %)5.6.1  System ~-~-> System Overview(%%) ===
769 769  
770 -(((
771 -(% style="color:#037691" %)__**WAN Settings: **__(%%)Setting for LG308N WAN port
772 -)))
773 773  
774 -(((
775 -(% style="color:#037691" %)__**WiFi Settings:  **__(%%)Setting for LG308N WiFi IP when use it as WiFi Client
776 -)))
766 +Shows the system info:
777 777  
778 778  
769 +[[image:image-20220916173046-3.png||height="613" width="868"]]
779 779  
780 -=== 5.5.4  System ~-~-> WiFi ===
781 781  
772 +(% data-sider-select-id="a7ee9375-c1cf-4a6c-a61d-38426e50d84a" %)
773 +=== 5.6.2  System ~-~-> General ( login settings) ===
782 782  
783 -LG308N WiFi Settings.
775 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419144019-5.png?rev=1.1||alt="image-20240419144019-5.png" height="813" width="863"]]
784 784  
785 -[[image:1652429430767-921.png||height="367" width="723"]]
777 +(((
778 +
786 786  
780 +(% data-sider-select-id="00e0325f-1698-4166-b578-eba5340e7e8e" style="color:#037691" %)**__System Password:__**
781 +)))
787 787  
783 +(((
784 +(% data-sider-select-id="95b842a8-0924-40db-acb5-4bc0aa4da2ea" %)
785 +There are two login for LG308N: (% style="color:blue" %)**root /dragino** (%%)or (% style="color:blue" %)**admin /dragino**. (%%)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
786 +)))
788 788  
789 -=== 5.5.5  System ~-~-> Cellular ===
788 +(((
789 +This page can be used to set the password for them.
790 +)))
790 790  
792 +(((
793 +(% style="color:#037691" %)**__Timezone:  __**(%%)Set device timezone.
794 +)))
791 791  
792 -While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
796 +(((
797 +(% data-sider-select-id="be6bdce7-110b-4367-bcd5-d176d288153e" %)
798 +(% data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" style="color:#037691" %)**__Port forwarding:  __**(%%)Enable/Disable the HTTP and SSH access via WAN interface.
793 793  
794 -[[image:1652429309615-825.png||height="320" width="732"]]
800 +(% data-sider-select-id="0e3c0e0e-5796-4a1a-b3da-cdfc059c383d" %)
801 +(% data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" style="color:#037691" %)**__Fallback Settings:  __**(%%)Enable/Disable the Fallback interface.
795 795  
803 +(% data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" style="color:#037691" %)**__Keepalive_Script:  __**(%%)Set the keepalive_scrpt interval.
796 796  
797 -(% style="color:red" %)**Note *: For LG308N which doesn't have the cellular module, this page will shows Cellular not detected.**
805 +(% data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" style="color:#037691" %)**__Logread Level:  __**(%%)Change the logread level.
798 798  
807 +(% data-sider-select-id="2140bc4a-c71f-4387-845a-510c0b050940" %)
808 +(% data-sider-select-id="31384c06-f8bc-420e-ba58-0a2d5916e600" style="color:#037691" %)**__Eable Internet Detect and Recover:  __**(%%)Enable/Disable the Internet Detect interface,Internet Detect is enabled by default. When there is no gateway network, it will reboot after 15 minutes.
799 799  
800 800  
801 -=== 5.5.6  System ~-~-> Network Status ===
811 +=== 5.6.3  System ~-~-> Backup/Restore Config ===
802 802  
813 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419145717-7.png?width=890&height=240&rev=1.1||alt="image-20240419145717-7.png"]]
803 803  
804 -[[image:1652429486609-208.png||height="415" width="728"]]
805 805  
816 +=== 5.6.4  System ~-~-> Remote.it ===
806 806  
818 +In the **System-> Remoteit** interface, users can configure the gateway to be accessed remotely via Remote.it.
807 807  
808 -=== 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
820 +the users can refer to this link to configure them: **[[Monitor & Remote Access Gateway>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access#H2.1A0RemoteAccessviaRemote.it.]]**
809 809  
822 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419150201-8.png?width=882&height=535&rev=1.1||alt="image-20240419150201-8.png"]]
810 810  
824 +
825 +=== (% data-sider-select-id="bf7cc535-bf5b-48cc-ade1-8cd02793cc24" %)5.6.5  System ~-~-> Remote Mgnt & Auto Provision(%%) ===
826 +
827 +
811 811  Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
812 812  
813 813  [[image:1652429518191-846.png||height="332" width="733"]]
... ... @@ -816,6 +816,7 @@
816 816  
817 817  [[image:1652429537849-154.png||height="339" width="722"]]
818 818  
836 +
819 819  Please see this document for detail:
820 820  
821 821  [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG308N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
... ... @@ -823,13 +823,13 @@
823 823  
824 824  R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Monitor & Remote Access Gateway.WebHome]]**
825 825  
826 -[[image:1652429624400-864.png||height="432" width="716"]]
844 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140017-16.png?rev=1.1||alt="image-20220916140017-16.png" height="593" width="872"]]
827 827  
846 +(% style="display:none" %) (%%)
828 828  
848 +=== (% data-sider-select-id="933284ec-43aa-4f3a-866d-3652cf9d6d99" %)5.6.6  System ~-~-> Firmware Upgrade(%%) ===
829 829  
830 -=== 5.5.8  System ~-~-> Firmware Upgrade ===
831 831  
832 -
833 833  We keep improving the DLOS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
834 834  
835 835  * **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],
... ... @@ -848,21 +848,29 @@
848 848  
849 849  (((
850 850  (% style="color:green" %)**Web~-~-> System~-~-> Firmware Upgrade**
869 +
870 +
851 851  )))
852 852  
853 -[[image:1652429711145-862.png||height="270" width="737"]]
873 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140103-17.png?rev=1.1||alt="image-20220916140103-17.png" height="274" width="871"]]
854 854  
855 855  
856 856  (((
857 857  Select the required image and click (% style="color:blue" %)**Flash Image.**(%%) The image will be uploaded to the device, and then click (% style="color:blue" %)**Process Update** (%%)to upgrade.
878 +
879 +
858 858  )))
859 859  
860 860  (((
861 861  (% style="color:red" %)**NOTE**: (%%)You normally need to (% style="color:blue" %)**//uncheck//**(%%) the (% style="color:blue" %)**Preserve Settings**(%%) checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
884 +
885 +
862 862  )))
863 863  
864 864  (((
865 865  The system will automatically boot into the new firmware after upgrade.
890 +
891 +
866 866  )))
867 867  
868 868  [[image:1652429962190-224.png||height="358" width="729"]]
... ... @@ -878,59 +878,178 @@
878 878  (% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
879 879  
880 880  
907 +=== (% data-sider-select-id="f1b2982b-d798-497e-9a52-aa589063cac4" %)5.6.7  System ~-~-> Reboot/Reset(%%) ===
881 881  
882 -=== 5.5.9  System ~-~-> Reboot/Reset ===
883 883  
910 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140312-18.png?rev=1.1||alt="image-20220916140312-18.png" height="274" width="873"]]
884 884  
885 -[[image:1652430197132-330.png||height="256" width="724"]]
886 -
887 887  (((
888 888  
889 -
890 -
891 891  )))
892 892  
893 -=== 5.5.10  System ~-~-> Package Maintain ===
916 +=== (% data-sider-select-id="0a08d67d-8e7f-41da-9bff-1355300ae3d7" %)5.6.8  System ~-~-> Package Maintain(%%) ===
894 894  
895 895  
896 -[[image:1652430243826-126.png||height="289" width="723"]]
919 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140421-19.png?rev=1.1||alt="image-20220916140421-19.png" height="687" width="868"]]
897 897  
921 +
898 898  Place to show what package has installed and possible to upgrade packages.
899 899  
900 900  
925 +== (% data-sider-select-id="038c76a1-26b1-41cb-9ab2-19e7644f5554" %)5.7  LogRead(%%) ==
901 901  
902 -== 5.6  LogRead ==
927 +=== (% data-sider-select-id="b4919c93-5eca-4b73-862c-9ea062f2196d" %)5.7.1 LogRead ~-~-> LoRa Log(%%) ===
903 903  
904 904  
905 -=== 5.6.1  LogRead ~-~-> LoRa Log ===
930 +Show the frequency for LoRa Radio and traffics.
906 906  
907 907  
908 -Show the frequency for LoRa Radio and traffics.
933 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140549-20.png?rev=1.1||alt="image-20220916140549-20.png" height="734" width="883"]]
909 909  
910 -[[image:1657069890320-513.png]]
911 911  
936 +=== (% data-sider-select-id="63e3559f-44af-4948-9e1e-d1d43817d95b" %)5.7.2 LogRead ~-~-> Gateway Traffic(%%) ===
912 912  
938 +Show the gateway traffic:
913 913  
940 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20240416112159-1.png?width=872&height=610&rev=1.1||alt="image-20240416112159-1.png"]]
914 914  
915 -=== 5.6.2  LogRead ~-~-> System Log ===
916 916  
943 +=== (% data-sider-select-id="77c6f3a0-3f73-4808-b92c-4d511a57b006" %)5.7.3 LogRead ~-~-> System Log(%%) ===
917 917  
945 +
918 918  Show the system log
919 919  
920 -[[image:1657069922599-794.png]]
921 921  
949 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20220916140732-21.png?rev=1.1||alt="image-20220916140732-21.png" height="706" width="867"]]
922 922  
923 923  
952 +=== (% data-sider-select-id="5b732c0d-cdf6-42bb-b7a1-584b93d7c430" %)5.7.4 LogRead ~-~-> Record Log(%%) ===
953 +
954 +This interface can record gateway logs:
955 +
956 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20240416112510-2.png?width=870&height=296&rev=1.1||alt="image-20240416112510-2.png"]]
957 +
958 +
924 924  = 6.  More features =
925 925  
926 926  
927 -== 6.1  More instructions ==
962 +== (% data-sider-select-id="2ef025e3-4214-4b1c-bb01-ee03e1db2bc2" %)6.1 NTP Service/Time Synchronization(%%) ==
928 928  
964 +The gateway time sync service is provided by ntpd
929 929  
930 -[[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)
966 +=== 1). Modify the NTP server address: ===
931 931  
968 +(% class="box" %)
969 +(((
970 +uci set system.ntp.server='0.openwrt.pool.ntp.org'
932 932  
972 +uci add_list system.ntp.server='1.openwrt.pool.ntp.org'
933 933  
974 +uci add_list system.ntp.server='2.openwrt.pool.ntp.org'
975 +
976 +uci add_list system.ntp.server='3.openwrt.pool.ntp.org'
977 +
978 +uci commit system
979 +)))
980 +
981 +
982 +== (% data-sider-select-id="060d238c-36fc-4453-b667-8dca3129ae44" %)6.2 Packet Filtering(%%) ==
983 +
984 +
985 +Drop unwanted packets.
986 +
987 +See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Filter%20unwanted%20LoRaWAN%20packets/]]
988 +
989 +
990 +== (% data-sider-select-id="8f1b89cd-d9d7-4d17-b064-f4615093f894" %)6.3 Remote Access(%%) ==
991 +
992 +
993 +Remote Access Devices for management.
994 +
995 +Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Monitor%20%26%20Remote%20Access%20Gateway/?Remote%20Access]]
996 +
997 +
998 +== (% data-sider-select-id="ef830314-529b-4dc8-8ec6-29545522bf2e" %)6.4 How to decode ABP LoRaWAN node(%%) ==
999 +
1000 +
1001 +Decode ABP:
1002 +
1003 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20~~-~~--%20LG308/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Communicate%20with%20ABP%20End%20Node%20without%20LoRaWAN%20Network%20Server%20---%20LG308/]]
1004 +
1005 +
1006 +== (% data-sider-select-id="304cacb4-477c-454f-90ec-649ffbe028fd" %)6.5 How to set data to MQTT broker(%%) ==
1007 +
1008 +
1009 +Only support ABP LoRaWAN End Node
1010 +
1011 +Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/MQTT%20Forward%20Instruction/]]
1012 +
1013 +
1014 +== (% data-sider-select-id="af36f615-2cec-4e1d-991d-436d8a56567d" %)6.6 How the gateway connects to Chirpstack v3/v4 via gateway-bridge(%%) ==
1015 +
1016 +
1017 +**For Chirpstack v3 Gateway-bridge**:
1018 +
1019 +The corresponding gateway firmware must be used :
1020 +
1021 +[[Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge~~-~~-build-v5.4.1679487778-20230322-2024/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge--build-v5.4.1679487778-20230322-2024/]]
1022 +
1023 +Chirpstack v3 via gateway-bridge Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0A0HowthegatewayconnectstoChirpstackv3viagateway-bridge>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0A0HowthegatewayconnectstoChirpstackv3viagateway-bridge]]
1024 +
1025 +
1026 +**For Chirpstack v4 Gateway-bridge**:
1027 +
1028 +The corresponding gateway firmware must be used :
1029 +
1030 +[[Chirpstack-gateway-bridge/Chirpstack-Bridge-V4~~-~~-build-v5.4.1670655072-20221210-1452/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V4--build-v5.4.1670655072-20221210-1452/]]
1031 +
1032 +Chirpstack v4 via gateway-bridge Instruction: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0HowthegatewayconnectstoChirpstackv4viagateway-bridge>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.A0HowthegatewayconnectstoChirpstackv4viagateway-bridge]]
1033 +
1034 +
1035 +(% style="color:red" %)**NOTE***(%%): Different chirpstack versions use different gateway-bridge configurations.
1036 +
1037 +After updating the Chirpstack gateway-bridge firmware, there is no need to re-download and install the Chirpstack gateway-bridge package
1038 +
1039 +
1040 +== (% data-sider-select-id="07a93540-35ce-4d6d-b77f-89e13682dd60" %)6.7  How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive).(%%) ==
1041 +
1042 +
1043 +USB card reader plugged into the USB port of the gateway
1044 +
1045 +Access the gateway Linux Command Line
1046 +
1047 +
1048 +Check the USB device
1049 +
1050 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20230425165308-2.png?rev=1.1||alt="image-20230425165308-2.png"]]
1051 +
1052 +
1053 +**Mount the USB device**
1054 +
1055 +(% class="box infomessage" %)
1056 +(((
1057 +**mount /dev/sda1 /mnt/**
1058 +)))
1059 +
1060 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20230425174131-4.png?rev=1.1||alt="image-20230425174131-4.png"]]
1061 +
1062 +
1063 +**Set up the automatic mount on boot**
1064 +
1065 +(% class="box infomessage" %)
1066 +(((
1067 +**sed -i '3cmount \/dev\/sda1 \/mnt\/' /etc/rc.local **
1068 +)))
1069 +
1070 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/DLOS8N/WebHome/image-20230425173831-3.png?width=833&height=105&rev=1.1||alt="image-20230425173831-3.png"]]
1071 +
1072 +
1073 +== (% data-sider-select-id="7ef57ac2-68e7-4fa6-bb6b-54f622bb6131" %)6.8  More instructions(%%) ==
1074 +
1075 +
1076 +[[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)
1077 +
1078 +
934 934  = 7.  Linux System =
935 935  
936 936  
... ... @@ -937,19 +937,18 @@
937 937  The LG308N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.
938 938  
939 939  
940 -
941 941  == 7.1  SSH Access for Linux console ==
942 942  
943 943  
944 944  User can access the Linux console via the SSH protocol. Make sure your PC and the LG308N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.
945 945  
946 -IP address:  IP address of LG308N
1090 +**IP address:  (% style="color:blue" %)IP address of LG308N(%%)**
947 947  
948 -Port:         22 (via WiFi AP mode) or 2222 (via WAN Interface)
1092 +**Port:  (% style="color:blue" %)22 (via WiFi AP mode) or 2222 (via WAN Interface)(%%)**
949 949  
950 -User Name:      (% style="color:green" %)**root**
1094 +**User Name:      (% style="color:blue" %)root(%%)**
951 951  
952 -Password:         (% style="color:green" %)**dragino** (% style="color:black" %)(default)
1096 +**Password:         (% style="color:blue" %)dragino(default)(%%)**
953 953  
954 954  
955 955  After logging in, you will be in the Linux console and can enter commands as shown below.
... ... @@ -957,12 +957,12 @@
957 957  [[image:1652431588565-830.png]]
958 958  
959 959  
960 -The “** (% style="background-color:yellow" %)logread -f"(%%)**command can be used to debug how system runs.
1104 +The “** (% style="color:blue" %)logread -f"(%%)**command can be used to debug how system runs.
961 961  
1106 +
962 962  [[image:1657070133275-283.png]]
963 963  
964 964  
965 -
966 966  == 7.2  Edit and Transfer files ==
967 967  
968 968  
... ... @@ -980,12 +980,13 @@
980 980  
981 981  (((
982 982  Screenshot is as below:
1127 +
1128 +
983 983  )))
984 984  
985 985  [[image:1652431650755-450.png]]
986 986  
987 987  
988 -
989 989  == 7.3  File System ==
990 990  
991 991  
... ... @@ -1001,7 +1001,6 @@
1001 1001  )))
1002 1002  
1003 1003  
1004 -
1005 1005  == 7.4  Package maintenance system ==
1006 1006  
1007 1007  
... ... @@ -1057,7 +1057,6 @@
1057 1057  (((
1058 1058  (% style="background-color:#dcdcdc" %)//Configuring iperf.//
1059 1059  
1060 -
1061 1061  
1062 1062  )))
1063 1063  
... ... @@ -1065,12 +1065,17 @@
1065 1065  
1066 1066  
1067 1067  
1068 -= 9.  FAQ =
1211 += 9.  OTA System Update =
1069 1069  
1070 1070  
1071 -== 9.1  How can I configure for a customized frequency band? ==
1214 +LG308N supports system auto update via OTA, please see **[[this URL>>url:http://wiki.dragino.com/xwiki/bin/view/OTA%20Update/]]** for the detail of this feature.
1072 1072  
1073 1073  
1217 += 10.  FAQ =
1218 +
1219 +== 10.1  How can I configure for a customized frequency band? ==
1220 +
1221 +
1074 1074  (((
1075 1075  See below link for how to customize frequency band: **[[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
1076 1076  )))
... ... @@ -1077,20 +1077,17 @@
1077 1077  
1078 1078  (((
1079 1079  
1080 -
1081 -
1082 1082  )))
1083 1083  
1084 -== 9.2  Can I connect LG308N to LORIOT? ==
1230 +== 10.2  Can I connect LG308N to LORIOT? ==
1085 1085  
1086 1086  
1087 1087  Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
1088 1088  
1089 1089  
1236 +== 10.3  Can I make my own firmware for the gateway, where can I find the source code? ==
1090 1090  
1091 -== 9.3  Can I make my own firmware for the gateway, where can I find the source code? ==
1092 1092  
1093 -
1094 1094  (((
1095 1095  Yes, You can make your own firmware for the LG308N for branding purposes or to add customized applications.
1096 1096  )))
... ... @@ -1100,17 +1100,15 @@
1100 1100  )))
1101 1101  
1102 1102  
1248 +== 10.4  Can I use 868Mhz version for 915Mhz bands? ==
1103 1103  
1104 -== 9.4  Can I use 868Mhz version for 915Mhz bands? ==
1105 1105  
1106 -
1107 1107  It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
1108 1108  
1109 1109  
1254 +== 10.5  Can I control the LEDs? ==
1110 1110  
1111 -== 9.5  Can I control the LEDs? ==
1112 1112  
1113 -
1114 1114  Except the PWR LED is controlled by +3v3 power directly. All other LEDs can be controlled by developer.
1115 1115  
1116 1116  
... ... @@ -1134,13 +1134,11 @@
1134 1134  OFF: echo 1 > /sys/class/gpio/gpio27/value
1135 1135  
1136 1136  
1280 += 11.  Trouble Shooting =
1137 1137  
1138 -= 10.  Trouble Shooting =
1282 +== 11.1  I get kernel error when install new package, how to fix? ==
1139 1139  
1140 1140  
1141 -== 10.1  I get kernel error when install new package, how to fix? ==
1142 -
1143 -
1144 1144  In some cases, when installing a package with **//opkg//**, it will generate a kernel error such as below due to a mismatch I the kernel ID:
1145 1145  
1146 1146  (% style="background-color:yellow" %)root@dragino-16c538:~~# opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk
... ... @@ -1162,10 +1162,9 @@
1162 1162  (% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends
1163 1163  
1164 1164  
1306 +== 11.2  How to recover the LG308N if the firmware crashes ==
1165 1165  
1166 -== 10.2  How to recover the LG308N if the firmware crashes ==
1167 1167  
1168 -
1169 1169  (((
1170 1170  Please follow this instruction to recover your gateway:  **[[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]**
1171 1171  )))
... ... @@ -1172,15 +1172,14 @@
1172 1172  
1173 1173  (((
1174 1174  
1175 -
1176 -
1177 1177  )))
1178 1178  
1179 -== 10.3  I configured LG308N for WiFi access and lost its IP. What to do now? ==
1317 +== (% data-sider-select-id="4a86b654-4887-420c-8049-1c447cf98cbb" %)11.3  I configured LG308N for WiFi access and lost its IP. What to do now?(%%) ==
1180 1180  
1181 1181  
1182 1182  [[image:1657074078183-336.png]]
1183 1183  
1322 +
1184 1184  (((
1185 1185  (((
1186 1186  The LG308N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LG308N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
... ... @@ -1203,43 +1203,55 @@
1203 1203  
1204 1204  (((
1205 1205  2. Configure PC's Ethernet port has IP: 172.31.255.253 and Netmask: 255.255.255.252
1345 +
1346 +
1206 1206  )))
1207 1207  
1208 1208  (((
1209 1209  As below photo:
1351 +
1352 +
1210 1210  )))
1211 1211  
1212 1212  [[image:1652435256286-879.png]]
1213 1213  
1357 +
1214 1214  3. In PC, use 172.31.255.254 to access LG308N via Web or Console.
1215 1215  
1216 1216  
1361 +== (% data-sider-select-id="4a86b654-4887-420c-8049-1c447cf98cbb" %)11.4  (%%)Why does the gateway reboot every 15 minutes without Internet? ==
1217 1217  
1218 -= 11.  Order Info =
1363 +Check whether Internet Detect is enabled on the System~-~->General interface.
1219 1219  
1365 +Internet Detect is enabled by default. When there is no gateway network, it will reboot after 15 minutes.
1220 1220  
1221 -**//PART:(% style="color:blue" %) DLOS8N-XXX-YYY//: (%%)**(% style="color:blue" %)
1367 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/LPS8N%20-%20LoRaWAN%20Gateway%20User%20Manual/WebHome/image-20240419145139-6.png?width=856&height=639&rev=1.1||alt="image-20240419145139-6.png"]]
1222 1222  
1223 -(% style="color:blue" %)**//XXX~://**(%%)**// Frequency Band//**
1224 1224  
1225 -* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1226 -* (% style="color:red" %)** 915**(% style="color:black" %):  valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1370 += 12.  Order Info =
1227 1227  
1372 +
1373 +**PART:(% style="color:blue" %) DLOS8N-XXX-YYY: (%%)**(% style="color:blue" %)
1374 +
1375 +(% style="color:blue" %)**XXX:**(%%)** Frequency Band**
1376 +
1377 +* (% style="color:red" %)** 868**(%%) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1378 +* (% style="color:red" %)** 915**(%%):  valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1379 +
1228 1228  (% style="color:#4f81bd" %)
1229 1229  
1230 -(% style="color:blue" %)**//YYY~://**(%%)**// 4G Cellular Option//**
1382 +(% style="color:blue" %)**YYY:**(%%)** 4G Cellular Option**
1231 1231  
1232 -* (% style="color:red" %)** EC25-E**(% style="color:black" %):  EMEA, Korea, Thailand, India.
1233 -* (% style="color:red" %)** EC25-A**(% style="color:black" %):  North America/ Rogers/AT&T/T-Mobile.
1234 -* (% style="color:red" %)** EC25-AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
1235 -* (% style="color:red" %)** EC25-J**(% style="color:black" %):  Japan, DOCOMO/SoftBank/ KDDI
1384 +* (% style="color:red" %)**EC25-E**(% style="color:black" %):  EMEA, Korea, Thailand, India
1385 +* (% style="color:red" %)**EC25-AFX**(% style="color:black" %): America: Verizon, AT&T(FirstNet), U.S.Cellular; Canada: Telus
1386 +* (% style="color:red" %)**EC25-AUX**(% style="color:black" %): Latin America, New Zeland, Taiwan
1387 +* (% style="color:red" %)**EC25-J**(% style="color:black" %):  Japan, DOCOMO, SoftBank, KDDI
1236 1236  
1237 1237  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
1238 1238  
1239 1239  
1392 += 13.  Packing Info =
1240 1240  
1241 -= 12.  Packing Info =
1242 -
1243 1243  (((
1244 1244  
1245 1245  
... ... @@ -1262,19 +1262,19 @@
1262 1262  * Package Size: 49 x 19.5 x x 19Package Size: 4912 cm
1263 1263  * Weight: 2.5kg
1264 1264  
1416 += 14.  Support =
1265 1265  
1266 1266  
1267 -= 13.  Support =
1268 -
1269 1269  * Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].
1420 +
1270 1270  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8.
1271 1271  Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before mentioned schedule.
1423 +
1272 1272  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to: [[support@dragino.com>>url:file:///C:/Users/11315/Documents/D:/Projects/LoRa%20Product%20Line/LG308%20Picocell%20Gateway/LG308/LG308%20%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6/support@dragino.com]]
1273 1273  
1426 += 15.  Reference =
1274 1274  
1275 1275  
1276 -= 14.  Reference =
1277 -
1278 1278  * Source code for LG08 LoRa Gateway: [[https:~~/~~/github.com/dragino/openwrt_lede-18.06>>url:https://github.com/dragino/openwrt_lede-18.06]]
1279 1279  
1280 1280  * OpenWrt official Wiki: [[http:~~/~~/www.openwrt.org/>>url:http://www.openwrt.org/]]
... ... @@ -1282,3 +1282,4 @@
1282 1282  * Firmware: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG308N-OLG308N/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]]
1283 1283  
1284 1284  * Hardware Source code: [[https:~~/~~/github.com/dragino/motherboard-hardware/tree/master/LG308N>>url:https://github.com/dragino/motherboard-hardware/tree/master/LG308]]
1436 +)))
1663317843420-717.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +86.8 KB
Content
image-20220916164504-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +42.4 KB
Content
image-20220916171413-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +143.3 KB
Content
image-20220916173046-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +142.9 KB
Content
image-20221101103113-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +55.8 KB
Content
image-20230406173729-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoye
Size
... ... @@ -1,0 +1,1 @@
1 +85.3 KB
Content