Skip to Content
Last modified by Kilight Cao on 2025/02/07 08:57
From version 118.2
edited by Xiaoling
on 2022/07/05 17:55
Change comment: There is no comment for this version
To version 123.2
edited by Xiaoling
on 2022/07/06 09:42
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -50,7 +50,7 @@
50 50  == 1.2  Specifications ==
51 51  
52 52  
53 -**Hardware System:**
53 +(% style="color:#037691" %)**Hardware System:**
54 54  
55 55  (((
56 56   Linux Part:
... ... @@ -60,7 +60,7 @@
60 60  * 64MB RAM
61 61  * 16MB Flash
62 62  
63 -**Interface:**
63 +(% style="color:#037691" %)**Interface:**
64 64  
65 65  * 10M/100M RJ45 Ports x 2
66 66  * WiFi : 802.11 b/g/n
... ... @@ -71,7 +71,7 @@
71 71  * Mini-PCI E connector x 1
72 72  * SX1302 + 2 x SX1250
73 73  
74 -**WiFi Spec:**
74 +(% style="color:#037691" %)**WiFi Spec:**
75 75  
76 76  * IEEE 802.11 b/g/n
77 77  * Frequency Band: 2.4 ~~ 2.462GHz
... ... @@ -84,7 +84,7 @@
84 84  ** 11g 54M : -71dbm
85 85  ** 11n 20M : -67dbm
86 86  
87 -**LoRa Spec:**
87 +(% style="color:#037691" %)**LoRa Spec:**
88 88  
89 89  * Up to -142.5 dBm sensitivity with SX1250 Tx/Rx front-end
90 90  * 70 dB CW interferer rejection at 1 MHz offset
... ... @@ -95,7 +95,7 @@
95 95  * Dynamic data-rate (DDR) adaptation
96 96  * True antenna diversity or simultaneous dual-band operation
97 97  
98 -**Cellular 4G LTE (optional):**
98 +(% style="color:#037691" %)**Cellular 4G LTE (optional):**
99 99  
100 100  * Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
101 101  * Standard Size SIM Slot
... ... @@ -242,13 +242,11 @@
242 242  LG308N supports flexible network set up for different environment. This section describes the typical network topology can be set in LG308N. The typical network set up includes:
243 243  )))
244 244  
245 -
246 246  * **WAN Port Internet Mode**
247 247  * **WiFi Client Mode**
248 248  * **WiFi AP Mode**
249 249  * **Cellular Mode**
250 250  
251 -
252 252  == 3.2  Use WAN port to access Internet ==
253 253  
254 254  By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N’s WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
... ... @@ -359,12 +359,12 @@
359 359  
360 360  (% style="color:red" %)**Note: Choose the cluster corresponds to a specific Gateway server address**
361 361  
360 +
362 362  * Europe 1 (% style="color:red" %)**corresponding Gateway server address:** (% style="color:black" %)eu1.cloud.thethings.network
363 363  * North America 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)nam1.cloud.thethings.network
364 364  * Australia 1 (% style="color:red" %)**corresponding Gateway server address: **(% style="color:black" %)au1.cloud.thethings.network
365 365  * Legacy V2 Console : (% style="color:red" %)**TTN v2 shuts down in December 2021**
366 366  
367 -
368 368  (% style="color:#4f81bd" %)**Step 4: Create a Gateway**
369 369  
370 370  [[image:1652422440891-514.png||height="360" width="747"]]
... ... @@ -559,14 +559,16 @@
559 559  Note *: **[[See this instruction for how to customize frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
560 560  
561 561  
562 -=== 5.2.2 LoRa ~-~-> ABP Decryption ===
560 +=== 5.2.2  LoRa ~-~-> ABP Decryption ===
563 563  
564 -The DLOS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
562 +The LG308N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
565 565  
566 566  * No internet connection.
567 567  * User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).
568 568  
569 569  (((
568 +
569 +
570 570  Detail of this feature: **[[Communication with ABP End Node>>doc:Main.Communicate with ABP End Node without LoRaWAN Network Server --- LG308.WebHome]]**
571 571  )))
572 572  
... ... @@ -573,9 +573,9 @@
573 573  [[image:1652423628833-467.png||height="357" width="755"]]
574 574  
575 575  
576 -== 5.3 LoRaWAN Settings ==
576 +== 5.3  LoRaWAN Settings ==
577 577  
578 -=== 5.3.1 LoRaWAN ~-~-> LoRaWAN ===
578 +=== 5.3.1  LoRaWAN ~-~-> LoRaWAN ===
579 579  
580 580  This page is for the connection set up to a general LoRaWAN Network server such as: [[TTN>>url:http://www.thethingsnetwork.org/]], [[ChirpStack>>url:https://www.chirpstack.io/]] etc
581 581  
... ... @@ -590,8 +590,9 @@
590 590  **See:** **[[Filter unwanted LoRaWAN packets>>doc:Main.Filter unwanted LoRaWAN packets.WebHome]]**
591 591  
592 592  
593 -=== 5.3.2 LoRaWAN ~-~-> Amazon AWS-IoT ===
594 594  
594 +=== 5.3.2  LoRaWAN ~-~-> Amazon AWS-IoT ===
595 +
595 595  [[image:1652428499323-384.png||height="275" width="723"]]
596 596  
597 597  
... ... @@ -598,10 +598,11 @@
598 598  (((
599 599  Please see this instruction to know more detail and demo for how to connect to **[[AWS-IoT LoRaWAN Core>>doc:Main.AWS IoT Core for LoRaWAN.WebHome]].**
600 600  
602 +
601 601  
602 602  )))
603 603  
604 -=== 5.3.3 LoRaWAN ~-~-> LORIOT ===
606 +=== 5.3.3  LoRaWAN ~-~-> LORIOT ===
605 605  
606 606  (((
607 607  Settings to communicate to LORIOT LoRaWAN Network Server: [[https:~~/~~/www.loriot.io/>>url:https://www.loriot.io/]]
... ... @@ -614,9 +614,9 @@
614 614  [[image:1652428648903-878.png||height="266" width="731"]]
615 615  
616 616  
617 -== 5.4 MQTT Settings ==
619 +== 5.4  MQTT Settings ==
618 618  
619 -If end nodes works in ABP mode, user can configure DLOS8N to transfer the data to MQTT broker,
621 +If end nodes works in ABP mode, user can configure LG308N to transfer the data to MQTT broker,
620 620  
621 621  Instruction: **[[MQTT Forward Instruction>>doc:Main.MQTT Forward Instruction.WebHome]]**
622 622  
... ... @@ -624,17 +624,19 @@
624 624  [[image:1652428705046-212.png||height="417" width="733"]]
625 625  
626 626  
627 -== 5.5 System ==
628 628  
629 -=== 5.5.1 System ~-~-> System Overview ===
630 +== 5.5  System ==
630 630  
632 +=== 5.5.1  System ~-~-> System Overview ===
633 +
631 631  Shows the system info:
632 632  
633 633  [[image:1652428773760-580.png||height="408" width="728"]]
634 634  
635 635  
636 -=== 5.5.2 System ~-~-> General ( login settings) ===
637 637  
640 +=== 5.5.2  System ~-~-> General ( login settings) ===
641 +
638 638  [[image:1652428861256-300.png||height="354" width="724"]]
639 639  
640 640  (((
... ... @@ -642,7 +642,7 @@
642 642  )))
643 643  
644 644  (((
645 -There are two login for DLOS8N: (% style="color:#4f81bd" %)root /dragino (% style="color:black" %)or (% style="color:#4f81bd" %)admin /dragino. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
649 +There are two login for DLOS8: (% style="color:#4f81bd" %)root /dragino (% style="color:black" %)or (% style="color:#4f81bd" %)admin /dragino. (% style="color:black" %)Both root and admin has the same right for WEB access. But root user has also the right to access via SSH to Linux system. admin only able to access WEB interface.
646 646  )))
647 647  
648 648  (((
... ... @@ -650,56 +650,60 @@
650 650  )))
651 651  
652 652  (((
653 -**__Timezone:__**Set device timezone.
657 +**__Timezone: __**Set device timezone.
654 654  )))
655 655  
656 656  (((
657 -**__Port forwarding:__**Enable/Disable the HTTP and SSH access via WAN interface.
661 +**__Port forwarding: __**Enable/Disable the HTTP and SSH access via WAN interface.
658 658  
663 +
659 659  
660 660  )))
661 661  
662 -=== 5.5.3 System ~-~-> Network ===
667 +=== 5.5.3  System ~-~-> Network ===
663 663  
664 664  [[image:1652429149053-824.png||height="467" width="725"]]
665 665  
666 666  (((
667 -**__LAN Settings:__**When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N’s own network.
672 +**__LAN Settings:  __**When the LG308N has the AP enable, LAN settings specify the network info for LG308N's own network.
668 668  )))
669 669  
670 670  (((
671 -__**WAN Settings:**__Setting for DLOS8N WAN port
676 +__**WAN Settings: **__Setting for LG308N WAN port
672 672  )))
673 673  
674 674  (((
675 -__**WiFi Settings:**__Setting for DLOS8N WiFi IP when use it as WiFi Client
676 -
677 -
680 +__**WiFi Settings:  **__Setting for LG308N WiFi IP when use it as WiFi Client
678 678  )))
679 679  
680 -=== 5.5.4 System ~-~-> WiFi ===
681 681  
682 -DLOS8N WiFi Settings.
683 683  
685 +=== 5.5.4  System ~-~-> WiFi ===
686 +
687 +LG308N WiFi Settings.
688 +
684 684  [[image:1652429430767-921.png||height="367" width="723"]]
685 685  
686 686  
687 -=== 5.5.5 System ~-~-> Cellular ===
688 688  
693 +=== 5.5.5  System ~-~-> Cellular ===
694 +
689 689  While use the cellular as Backup WAN, device will use Cellular for internet connection while WAN port or WiFi is not valid and switch back to WAN port or WiFi after they recover.
690 690  
691 691  [[image:1652429309615-825.png||height="320" width="732"]]
692 692  
693 -(% style="color:red" %)Note *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.
699 +(% style="color:red" %)Note *: For LG308N which doesn't have the cellular module, this page will shows Cellular not detected.
694 694  
695 695  
696 -=== 5.5.6 System ~-~-> Network Status ===
697 697  
703 +=== 5.5.6  System ~-~-> Network Status ===
704 +
698 698  [[image:1652429486609-208.png||height="415" width="728"]]
699 699  
700 700  
701 -=== 5.5.7 System ~-~-> Remote Mgnt & Auto Provision ===
702 702  
709 +=== 5.5.7  System ~-~-> Remote Mgnt & Auto Provision ===
710 +
703 703  Auto Provision is the feature for batch configure and remote management. It can be used in below two cases:
704 704  
705 705  [[image:1652429518191-846.png||height="332" width="733"]]
... ... @@ -710,8 +710,10 @@
710 710  
711 711  Please see this document for detail:
712 712  
721 +[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG308N/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
722 +
713 713  (((
714 -[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Application_Note/&file=Auto-update-feature.pdf]]
724 +
715 715  )))
716 716  
717 717  
... ... @@ -720,8 +720,9 @@
720 720  [[image:1652429624400-864.png||height="432" width="716"]]
721 721  
722 722  
723 -=== 5.5.8 System ~-~-> Firmware Upgrade ===
724 724  
734 +=== 5.5.8  System ~-~-> Firmware Upgrade ===
735 +
725 725  We keep improving the DLOS8N Linux side firmware for new features and bug fixes. Below are the links for reference.
726 726  
727 727  * **Latest firmware**: [[LoRa Gateway Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]],
... ... @@ -728,10 +728,12 @@
728 728  
729 729  ( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )
730 730  
742 +
731 731  * **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].
732 732  
733 733  ( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )
734 734  
747 +
735 735  (((
736 736  The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.
737 737  )))
... ... @@ -742,6 +742,7 @@
742 742  
743 743  [[image:1652429711145-862.png||height="270" width="737"]]
744 744  
758 +
745 745  Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.
746 746  
747 747  (% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
... ... @@ -756,18 +756,22 @@
756 756  
757 757  (% style="color:#4f81bd" %)**//root@OpenWrt:~~# /sbin/sysupgrade –n /var/Your_Image//**
758 758  
773 +
759 759  (% style="color:red" %)**NOTE**(%%) : it is important to transfer the image in the /var directory, otherwise it may exceed the available flash size.
760 760  
761 761  
762 -=== 5.5.9 System ~-~-> Reboot/Reset ===
763 763  
778 +=== 5.5.9  System ~-~-> Reboot/Reset ===
779 +
764 764  [[image:1652430197132-330.png||height="256" width="724"]]
765 765  
766 766  (((
767 767  
784 +
785 +
768 768  )))
769 769  
770 -=== 5.5.10 System ~-~-> Package Maintain ===
788 +=== 5.5.10  System ~-~-> Package Maintain ===
771 771  
772 772  [[image:1652430243826-126.png||height="289" width="723"]]
773 773  
... ... @@ -774,52 +774,45 @@
774 774  Place to show what package has installed and possible to upgrade packages.
775 775  
776 776  
777 -== 5.6 LogRead ==
778 778  
779 -=== 5.6.1 LogRead ~-~-> LoRa Log ===
796 +== 5.6  LogRead ==
780 780  
798 +=== 5.6.1  LogRead ~-~-> LoRa Log ===
781 781  
782 782  Show the frequency for LoRa Radio and traffics.
783 783  
784 -[[image:image-20220615204306-1.png||height="575" width="733"]]
802 +[[image:1657069890320-513.png]]
785 785  
786 786  
787 -Show the IoT Server Connection State and FWD State
788 788  
789 -[[image:image-20220616083933-1.png||height="556" width="729"]]
790 790  
791 -DLOS8 can view GPS location in the Logread FWD State
807 +=== 5.6.2  LogRead ~-~-> System Log ===
792 792  
809 +Show the system log
793 793  
794 -Show the Error logs, RxTxJson lorawan packages, and PULL State
811 +[[image:1657069922599-794.png]]
795 795  
796 -[[image:image-20220615205416-6.png||height="442" width="884"]]
797 797  
798 798  
799 -=== 5.6.2 LogRead ~-~-> System Log ===
815 += 6.  More features =
800 800  
801 -Show the system log
817 +== 6.1  More instructions ==
802 802  
803 -[[image:1652430369760-511.png||height="373" width="730"]]
804 -
805 -= 6. More features =
806 -
807 -== 6.1 More instructions ==
808 -
809 809  [[LoRaWAN Gateway Instruction>>doc:Main.WebHome]](LoRaWAN Gateway)
810 810  
811 811  
812 -= 7. Linux System =
813 813  
814 -The DLOS8N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.
823 += 7.  Linux System =
815 815  
825 +The LG308N is based on the OpenWrt Linux system. It is open source, and users are free to configure and modify the Linux settings.
816 816  
817 -== 7.1 SSH Access for Linux console ==
818 818  
819 -User can access the Linux console via the SSH protocol. Make sure your PC and the DLOS8N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.
828 +== 7.1  SSH Access for Linux console ==
820 820  
821 -IP address:  IP address of DLOS8N
830 +User can access the Linux console via the SSH protocol. Make sure your PC and the LG308N are connected to the same network, then use a SSH tool (such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows) to access it.
822 822  
832 +IP address:  IP address of LG308N
833 +
823 823  Port:         22 (via WiFi AP mode) or 2222 (via WAN Interface)
824 824  
825 825  User Name:      (% style="color:green" %)**root**
... ... @@ -826,19 +826,22 @@
826 826  
827 827  Password:         (% style="color:green" %)**dragino** (% style="color:black" %)(default)
828 828  
840 +
829 829  After logging in, you will be in the Linux console and can enter commands as shown below.
830 830  
831 831  [[image:1652431588565-830.png]]
832 832  
845 +
833 833  The “(% class="mark" %)**logread -f**(%%)” command can be used to debug how system runs.
834 834  
835 -[[image:1652431609193-637.png||height="214" width="732"]]
848 +[[image:1657070133275-283.png]]
836 836  
837 837  
838 -== 7.2 Edit and Transfer files ==
839 839  
852 +== 7.2  Edit and Transfer files ==
853 +
840 840  (((
841 -The DLOS8N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.
855 +The LG308N supports the (% style="color:green" %)**SCP protocol** (% style="color:black" %)and has a built-in (% style="color:green" %)**SFTP server**. (% style="color:black" %)There are many ways to edit and transfer files using these protocols.
842 842  )))
843 843  
844 844  (((
... ... @@ -846,7 +846,7 @@
846 846  )))
847 847  
848 848  (((
849 -After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the DLOS8N, or edit the files directly in the windows.
863 +After establishing access via WinSCP to the device, you can use an FTP style window to drag / drop files to the LG308N, or edit the files directly in the windows.
850 850  )))
851 851  
852 852  (((
... ... @@ -856,25 +856,25 @@
856 856  [[image:1652431650755-450.png]]
857 857  
858 858  
859 -== 7.3 File System ==
873 +== 7.3  File System ==
860 860  
861 861  (((
862 -The DLOS8N has a 16MB flash and a 64MB RAM. The /var and /tmp directories are in the RAM, so contents stored in /tmp and /var will be erased after rebooting the device. Other directories are in the flash and will remain after reboot.
863 -)))
864 -
865 865  (((
866 -The Linux system uses around 8MB ~~10MB flash size which means there is not much room for user to store data in the DLOS8N flash.
877 +The LG308N has a 16MB flash and a 64MB RAM. The /var and /tmp directory are in the RAM, contents stored in /tmp and /var will be erased after reboot the device. Other directories are in the flash and will keep after reboot.
867 867  )))
868 868  
880 +
869 869  (((
870 -You can use an external USB flash memory device to extend the size of flash memory for storage.
882 +The Linux system use around 8MB ~~10MB flash size which means there is not much room for user to store data in the LG308N flash. User can use an external USB flash to extend the size for storage.
871 871  )))
884 +)))
872 872  
873 873  
874 -== 7.4 Package maintenance system ==
875 875  
876 -DLOS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure DLOS8N to use **//iperf //**.
888 +== 7.4  Package maintenance system ==
877 877  
890 +LG308N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure DLOS8N to use **//iperf //**.
891 +
878 878  (((
879 879  Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])
880 880  )))
... ... @@ -924,15 +924,19 @@
924 924  
925 925  (((
926 926  (% style="background-color:#dcdcdc" %)//Configuring iperf.//
941 +
942 +
943 +
927 927  )))
928 928  
929 -= 8. Upgrade Linux Firmware =
946 += 8.  Upgrade Linux Firmware =
930 930  
931 931  
932 -= 9. FAQ =
933 933  
934 -== 9.1 How can I configure for a customized frequency band? ==
950 += 9.  FAQ =
935 935  
952 +== 9.1  How can I configure for a customized frequency band? ==
953 +
936 936  (((
937 937  See below link for how to customize frequency band: **[[How to customized LoRaWAN frequency band>>doc:Main.How to customized LoRaWAN frequency band.WebHome]]**
938 938  )))
... ... @@ -941,15 +941,15 @@
941 941  
942 942  )))
943 943  
944 -== 9.2 Can I connect DLOS8N to LORIOT? ==
962 +== 9.2  Can I connect DLOS8N to LORIOT? ==
945 945  
946 946  Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
947 947  
948 948  
949 -== 9.3 Can I make my own firmware for the gateway, where can I find the source code? ==
967 +== 9.3  Can I make my own firmware for the gateway, where can I find the source code? ==
950 950  
951 951  (((
952 -Yes, You can make your own firmware for the DLOS8N for branding purposes or to add customized applications.
970 +Yes, You can make your own firmware for the LG308N for branding purposes or to add customized applications.
953 953  )))
954 954  
955 955  (((
... ... @@ -957,11 +957,37 @@
957 957  )))
958 958  
959 959  
960 -== 9.4 Can I use 868Mhz version for 915Mhz bands? ==
978 +== 9.4  Can I use 868Mhz version for 915Mhz bands? ==
961 961  
962 962  It is possible but the distance will be very short, you can select US915 frequency band in 868Mhz version hardware. It will work but you will see the performance is greatly decreased because the 868Mhz version has an RF filter for band 863~~870Mhz, all other frequencies will have high attenuation.
963 963  
964 964  
983 +== 9.5  Can I control the LEDs? ==
984 +
985 +Except the PWR LED is controlled by +3v3 power directly. All other LEDs can be controlled by developer.
986 +
987 +
988 +(% style="color:blue" %)**Control Globe LED:**
989 +
990 +ON: echo 1 > /sys/class/leds/dragino2\:red\:wlan/brightness 
991 +
992 +OFF: echo 0 > /sys/class/leds/dragino2\:red\:wlan/brightness
993 +
994 +
995 +(% style="color:blue" %)**Control HEART LED:**
996 +
997 +First export the gpio27 and set to out
998 +
999 +echo 27 > /sys/class/gpio/export
1000 +
1001 +echo out > /sys/class/gpio/gpio27/direction
1002 +
1003 +ON: echo 0 > /sys/class/gpio/gpio27/value
1004 +
1005 +OFF: echo 1 > /sys/class/gpio/gpio27/value
1006 +
1007 +
1008 +
965 965  = 10. Trouble Shooting =
966 966  
967 967  == 10.1 I get kernel error when install new package, how to fix? ==
... ... @@ -987,8 +987,9 @@
987 987  (% style="background-color:yellow" %)Opkg install kmod-dragino2-si3217x_3.10.49+0.2-1_ar71xx.ipk –force-depends
988 988  
989 989  
990 -== 10.2 How to recover the DLOS8N if the firmware crashes ==
991 991  
1035 +== 10.2  How to recover the LG308N if the firmware crashes ==
1036 +
992 992  (((
993 993  Please follow this instruction to recover your gateway:  **[[Recover Gateway>>doc:Main.How to Recover Gateway if can't access it.WebHome]]**
994 994  )))
... ... @@ -997,12 +997,12 @@
997 997  
998 998  )))
999 999  
1000 -== 10.3 I configured DLOS8N for WiFi access and lost its IP. What to do now? ==
1045 +== 10.3 I configured LG308N for WiFi access and lost its IP. What to do now? ==
1001 1001  
1002 -[[image:1652435238615-272.png||height="247" width="727"]]
1047 +[[image:1657071488240-907.png]]
1003 1003  
1004 1004  (((
1005 -The DLOS8N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access DLOS8N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
1050 +The LG308N has a fall-back IP address on its WAN port. This IP is always enabled so you can use the fall-back IP to access LG308N no matter what the WiFi IP is. The fall back IP is useful for connecting and debug the unit.
1006 1006  )))
1007 1007  
1008 1008  (% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.
... ... @@ -1010,11 +1010,9 @@
1010 1010  
1011 1011  Steps to connect via fall back IP:
1012 1012  
1013 -~1. Connect PC’s Ethernet port to DLOS8N’s WAN port
1058 +~1. Connect PC's Ethernet port to LG01's LAN port
1014 1014  
1015 -2. Configure PC’s Ethernet port has
1016 - IP: 172.31.255.253 and
1017 - Netmask: 255.255.255.252
1060 +2. Configure PC's Ethernet port has IP: 172.31.255.253 and Netmask: 255.255.255.252
1018 1018  
1019 1019  As below photo:
1020 1020  
1657069890320-513.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +63.2 KB
Content
1657069922599-794.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +58.2 KB
Content
1657070133275-283.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +221.0 KB
Content
1657071488240-907.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +60.0 KB
Content