Skip to Content
Version 73.1 by Kilight Cao on 2022/11/04 16:00
Show last authors
1 (% style="text-align:center" %)
2 [[image:image-20221028134937-1.jpeg||height="466" width="466"]]
3
4 (((
5
6
7
8 )))
9
10 **Table of Contents：**
11
12 {{toc/}}
13
14 = **1. Introduction** =
15
16
17 == **1.1 What is LG01-V2** ==
18
19
20 (((
21 (((
22 The LG01-V2 is an (% style="color:green" %)**open-source single channel LoRa Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via (% style="color:green" %)**WiFi , Ethernet or Cellular Network**(%%) (via Optional 4G module). The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
23 )))
24
25 (((
26 LG01-V2 supports (% style="color:green" %)**remote management**(%%). System Integrator can easy to remote monitor the gateway and maintain it.
27 )))
28
29
30
31 == **1.2 Specifications** ==
32
33
34 (% style="color:#037691" %)**Hardware System:**
35
36 * CPU: Quad-core Cortex-A7 1.2Ghz
37 * RAM: 512MB
38 * eMMC: 4GB
39
40 (% style="color:#037691" %)**Interface:**
41
42 * 10M/100M RJ45 Ports x 1
43 * WiFi 802.11 b/g/n
44
45 (% style="color:#037691" %)**Operating Condition:**
46
47 * Work Temperature: -20 ~~ 65°C
48 * Storage Temperature: -20 ~~ 65°C
49 * Power Input: 5V, 2A, DC
50
51 == **1.3 Features** ==
52
53
54 * Open Source Debian system
55 * Managed by Web GUI, SSH via WAN or WiFi
56 * Remote Management
57 * Auto-provisioning for batch deployment and management
58 * LoRa Gateway
59 * Built-in (% style="color:#037691" %)//**The Things Network**//(%%) local LoRaWAN server
60 * Built-in  (% style="color:#037691" %)//**Node-Red**// (%%)local Application server
61
62 == **1.4 Block Diagram** ==
63
64
65
66 == **1.5 LED Indicators** ==
67
68
69 LG01-V2 has totally four LEDs, They are:
70
71
72 (% style="color:blue" %)//**➢ Power LED**//(%%)//: This RED LED will be solid if the device is properly powered//
73
74 (% style="color:blue" %)//**➢ ETH LED**//(%%)//:  This RGB LED will blink GREEN when the ETH port is connecting//
75
76 (% style="color:blue" %)//**➢ SYS LED**//(%%)//:  This RGB LED will show different colors in different states~://
77
78 // ✓ **SOLID GREEN:** The device is alive with a LoRaWAN server connection.//
79
80 // ✓ **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together//
81
82 // ✓** SOLID RED:** Device doesn't have an Internet connection.//
83
84 (% style="color:blue" %)//**➢ WIFI LED**//(%%)//: This LED shows the WIFI interface connection status.//
85
86
87
88 == **1.6 Button Intruction** ==
89
90
91 LG01-V2 has a black toggle button, which is:
92
93
94 (% style="color:blue" %)**//➢ //Long press 4-5s  : **(%%)the gateway will reload the Network and Initialize wifi configuration
95
96 // **LED status: ** ETH LED will BLINKIND BULE Until the reload is finished.//
97
98
99 (% style="color:blue" %)//**➢ **//**Long press more than 10s:**(%%)**    **//the gateway will restore the factory settings.//
100
101 //**LED status: ** ETH LED will SOLID BULE Until the restore is finished.//
102
103
104
105 = **2. Quick Start** =
106
107
108 The LG01-V2 supports network access via Ethernet or Wi-Fi connection and runs without a network.
109
110 In most cases, the first thing you need to do is make the LG01-v2 accessible to the network.
111
112
113 == **2.1 Connects to the network and accesses the gateway Web UI** ==
114
115
116 == **2.1.1 connect the network.** ==
117
118
119 === (% style="color:blue" %)**Method 1**(%%):  Connect via Ethernet with DHCP IP from the router ===
120
121
122 Connect the LG01-V2 Ethernet port to your router and LG01-V2 can obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the LG01-V2.
123
124 You can also use this IP to connect.
125
126
127 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622100129-1.png?width=1263&height=332&rev=1.1||alt="image-20220622100129-1.png"]]
128
129
130 === (% style="color:blue" %)**Method 2**(%%):  Connect via WiFi with DHCP IP from the router ===
131
132
133 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622100542-2.png?width=1256&height=369&rev=1.1||alt="image-20220622100542-2.png"]]
134
135
136 Fill in the WiFi information by checking the box and clicking (% style="color:red" %)**Save&Apply**
137
138
139 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102702-6.png?rev=1.1||alt="image-20220622102702-6.png"]]
140
141
142 **Wi-Fi configuration successful**
143
144
145 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220622102847-7.png?rev=1.1||alt="image-20220622102847-7.png"]]
146
147
148
149 = **3. Web Configure Pages** =
150
151 == **3.1 Home** ==
152
153 //Shows the system running status~://
154
155 [[image:image-20221104155612-1.png||height="497" width="942"]]
156
157
158 == **3.2 Network Settings** ==
159
160
161 === **3.2.1 Network ~-~-> WiFi** ===
162
163
164 [[image:image-20221104155654-2.png||height="319" width="813"]]
165
166
167
168 === **3.4.2 Network ~-~-> System Status** ===
169
170
171 [[image:image-20221104155724-3.png||height="679" width="861"]]
172
173
174
175 === **3.4.3 Network ~-~-> Firewall** ===
176
177
178 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220616115351-6.png?width=661&height=244&rev=1.1||alt="image-20220616115351-6.png"]]
179
180
181
182 == **3.5 System** ==
183
184
185 === **3.5.1  System ~-~-> System Overview** ===
186
187
188 Shows the system info:
189
190 [[image:image-20221104155907-4.png]]
191
192
193
194 === **3.5.2 System ~-~-> Backup/Restore** ===
195
196
197 [[image:image-20221104155928-5.png||height="334" width="880"]]
198
199
200 = (% id="cke_bm_1978S" style="display:none" %)** **(%%)**4. Build in Server** =
201
202
203 The default factory version of LG01-V2 is installed with the built-in Applicant server: (% style="color:blue" %)**Node-Red**
204
205
206 [[image:image-20221104155949-6.png||height="315" width="1023"]]
207
208
209 (% style="color:red" %)**Note:**
210
211 **Path**: System ~-~-> Built-in Server
212
213
214 **Troubleshooting:**
215
216
217 **~ 1. URL does not jump properly**
218
219 For the Node-Red, you can use the local IP address and the port is 1880 to access it.
220
221
222
223 == **4.1 Application Server ~-~- Node-Red** ==
224
225
226 You can access the gateway's built-in AS server of (% style="color:blue" %)**Node-Red **(%%)via the URL((% style="background-color:yellow" %)__**//http:~/~/<hostname>:1880 or http:~/~/<local-IPV4-address>//**__(%%)) in your browser.
227
228
229 Such as (% style="background-color:yellow" %)__**//http:~/~/dragino-54ff12:1880  or http:~/~/<Local-IPV4-Address>//**__
230
231
232 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220725172124-3.png?width=843&height=610&rev=1.1||alt="image-20220725172124-3.png"]]
233
234
235 = **5. How to configure the Lora Gateway** =
236
237
238 == **5.1 Access the Lora configuration page** ==
239
240
241 Users can access the Lora configuration page by running the following command, then select the option **''serial port setup"**:
242
243 (% class="box infomessage" %)
244 (((
245 **root@dragino-2406ef:~~# minicom -s**
246 )))
247
248 [[image:image-20221029174637-2.png||height="410" width="524"]]
249
250
251 And then, change the setting:
252
253 (% class="box infomessage" %)
254 (((
255 **Serial Device :** **/dev/ttyUSB0**
256
257 **Bps/Par/Bits : 9600 8N1**
258 )))
259
260
261 (% style="color:red" %)**Note: Enter the corresponding letter to change the configuration, like A,B,C**(%%)
262 (% style="color:red" %)[[image:image-20221029174703-3.png]]
263
264
265 Enter **AT+CFG **in the interface to get the configuration,
266
267
268 (% class="box infomessage" %)
269 (((
270 AT+FRE=868.100,868.100  ~-~--> TX and RX frequency
271 AT+GROUPMOD=0,0  ~-~--> TX and RX group
272 AT+BW=0,0  ~-~--> TX and RX Bandwidth
273 AT+SF=12,12  ~-~--> TX and RX Spreading Factor
274 AT+POWER=14  ~-~--> TX Power Range
275 AT+CRC=1,1  ~-~--> TX and RX CRC Type
276 AT+HEADER=0,0  ~-~--> TX and RX Header Type
277 AT+CR=1,1  ~-~--> TX and RX Coding Rate
278 AT+IQ=0,0  ~-~--> TX and RX InvertIQ
279 AT+PREAMBLE=8,8  ~-~--> TX and RX Preamble Length
280 AT+SYNCWORD=0  ~-~-->  Syncword**(0: private，1: public)**
281 AT+RXMOD=65535,0  ~-~-->  Rx Timeout and Reply mode
282 AT+RXDAFORM=1                              
283 )))
284
285
286 == **5.2 Example: LG01**-**V2 Peer-to-Peer** ==
287
288
289 [[image:image-20221104102736-3.png||height="282" width="723"]]
290
291
292 The user can run the AT command to set the LG01-V2 RX window always open as a Receiver, the LA66 Shield uses **AT+SEND=1,hello world,2,3** to simulate sending data,
293
294 **Prerequisites: **The configuration of LG01-V2 and  LA66 Shield must match, users can use **AT+CFG** to check all configurations.
295
296
297 (% style="color:red; font-weight:bold" %)**LG01-V**(% style="color:red" %)**2 as Receiver: (configured as AT+RXMOD=65535,2)**
298
299 [[image:image-20221102140053-4.png]]
300
301
302 (% style="color:red" %)**LA66 Shield as Sender: (AT+SEND=1,hello world,2,3)**
303
304 [[image:1667456058832-484.png||height="291" width="353"]]
305
306
307 Instruction for Peer-to-Peer firmware:[[ **Instruction **>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LA66%20LoRaWAN%20Shield%20User%20Manual/Instruction%20for%20LA66%20Peer%20to%20Peer%20firmware/]]
308 )))
309
310
311 Users can import this example in node-red: **[[attach:serial USB.json||target="_blank"]]**
312
313 [[image:image-20221104100520-2.png||height="605" width="1150"]]
314
315
316 = (% style="color:inherit; font-family:inherit; font-size:29px" %)**6. How users can access LG01**(%%)**-V​​​​​​​(% style="color:inherit; font-family:inherit; font-size:29px" %)2 using serial USB(%%)** =
317
318
319 (% style="color:blue" %)**USB TTL to LG01-V2  Connection:**
320
321
322 Port 1 of the UART on the LG01-V2 is GND
323
324 (% class="box infomessage" %)
325 (((
326 **TXD  <~-~--> UART RXD (Gray line)**
327
328 **RXD  <~-~--> UART TXD (White line)**
329
330 **GND <~-~--> GND (Black line)**
331 )))
332
333
334 **LG01-V2 UART connection photo**
335
336 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804163015-1.png?width=466&height=621&rev=1.1||alt="image-20220804163015-1.png"]]
337
338
339
340 In the PC, you can use the serial port tool(such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows), you need to set the serial baud rate to (% style="color:blue" %)**115200**(%%) to access the serial console for LG01v2. LG01v2 will output system info once power on as below:
341
342
343 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164928-3.png?width=332&height=320&rev=1.1||alt="image-20220804164928-3.png"]]
344
345 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164747-2.png?width=594&height=622&rev=1.1||alt="image-20220804164747-2.png"]]
346
347
348 = **7. FAQ** =
349
350
351 == **7.1 How does LG01-V2 communicate with Lora shield (LoRa.h)** ==
352
353
354 This example describes how to use LG01-V2, LoRa Shield to set up a LoRa network
355
356 [[image:image-20221103152238-8.png||height="251" width="654"]]
357
358
359 (% style="color:red" %)**Prerequisites: The configurations of LG01-V2 and Lora shield must match**
360
361 **LG01-V2 configuration:**
362
363 (% class="box infomessage" %)
364 (((
365 AT+FRE=868.100,868.100  ~-~--> TX and RX frequency set: 868100000
366 AT+BW=0,0  ~-~--> TX and RX Bandwidth set: 125kHz
367 AT+SF=12,12  ~-~--> TX and RX Spreading Factor set: SF12
368 AT+POWER=14  ~-~--> TX Power Range
369 AT+CRC=1,1  ~-~--> TX and RX CRC Type
370 AT+HEADER=0,0  ~-~--> TX and RX Header Type
371 AT+CR=1,1  ~-~--> TX and RX Coding Rate
372 AT+IQ=0,0  ~-~--> TX and RX InvertIQ
373 AT+PREAMBLE=8,8  ~-~--> TX and RX Preamble Length set: 8
374 AT+SYNCWORD=0  ~-~-->  Syncword**(0: private，1: public), **the corresponding Lora shield syncword is 0x12
375 AT+RXMOD=65535,0  ~-~-->  Rx Timeout and Reply mode,RX window always open
376 AT+RXDAFORM=1    
377 )))
378
379 **Lora shield configuration:**
380
381 Lora Shield example: [[attach:LoRa_Shield_Sketch_For_MQTT.ino||target="_blank"]] , [[attach:arduino-LoRa-master.zip||target="_blank"]]
382
383 [[image:image-20221101161318-2.png]]
384
385
386 **Test LG01-V2 to receive Lora Shield data:**
387
388 [[image:image-20221101161951-3.png]]
389
390
391 **Test the LG01-V​​​​​​​2 to send data:**
392
393 [[image:image-20221101162527-4.png]]
394
395
396 = (% style="color:inherit; font-family:inherit; font-size:29px" %)**8. Supports**(%%) =
397
398
399 (((
400 **//If you are experiencing issues and can't solve them, you can send mail to [[support@dragino.com>>mailto:support@dragino.com]].//**
401 )))
402
403 (((
404 **//With your question as detailed as possible. We will reply and help you in the shortest.//**
405
406
407
408 = **9. Reference** =
409
410
411 * Install Tago Core: Refer **Install Tago Core in LPS8v2** in[[ Instruction>>doc:Main.Tago\.IO.WebHome]].
412 * [[Advance OS Reference Guide for LPS8v2>>doc:Main.Armbian OS instruction.WebHome]].
413
414
415 )))
416
417 = **10. Order Info** =
418
419
420 (% style="color:#0000ff" %)**LPS8v2-XXX-YYY**
421
422 (% style="color:#0000ff" %)**XXX**(% style="color:black" %): Frequency Band
423
424 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
425 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
426 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
427 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
428 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
429 * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
430
431 (% style="color:#0000ff" %)**YYY**(% style="color:black" %): 4G Cellular Option
432
433 * (% style="color:red" %)**E**(%%):  EMEA, Korea, Thailand, India.
434 * (% style="color:red" %)**A**(%%):  North America/ Rogers/AT&T/T-Mobile.
435 * (% style="color:red" %)**AU**(%%): Latin America, New Zeland, Taiwan
436 * (% style="color:red" %)**J**(%%):  Japan, DOCOMO/SoftBank/ KDDI
437
438 More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
439
440
441
442 = **10. Manufacturer Info** =
443
444
445 **Shenzhen Dragino Technology Development co. LTD**
446
447 Room 202, Block B, BCT Incubation Bases (BaoChengTai),  No.8 CaiYunRoad
448
449 LongCheng Street, LongGang District ; Shenzhen 518116,China
450
451
452
453 = **11. FCC Warning** =
454
455
456 (((
457 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
458 )))
459
460 (((
461 ~-~- Reorient or relocate the receiving antenna.
462 )))
463
464 (((
465 ~-~- Increase the separation between the equipment and receiver.
466 )))
467
468 (((
469 ~-~- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
470 )))
471
472 (((
473 ~-~- Consult the dealer or an experienced radio/TV technician for help.
474 )))
475
476
477 (((
478 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
479 )))
480
481
482 (((
483 The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
484
485
486 )))
487
488 ~)~)~)