Last modified by Kilight Cao on 2024/10/12 08:58
<
From version < 150.1
edited by Kilight Cao
on 2024/10/12 08:58
To version < 142.1 >
edited by Kilight Cao
on 2023/09/25 17:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -7,7 +7,7 @@
7 7  
8 8  )))
9 9  
10 -**Table of Contents:**
10 +**Table of Contents：**
11 11  
12 12  {{toc/}}
13 13  
... ... @@ -25,9 +25,7 @@
25 25  (((
26 26  The LG01v2 is an (% style="color:blue" %)**open-source single channel LoRa Gateway**(%%). It lets you bridge LoRa wireless network to an IP network via (% style="color:blue" %)**WiFi , Ethernet or Cellular Network**(%%) (via Optional 4G module). The LoRa wireless allows users to send data and reach extremely long ranges at low data rates.
27 27  
28 -LG01v2 is specially designed for (% style="color:blue" %)**peer-to-peer LoRa**(%%) protocol instead of LoRaWAN protocol. The LG01v2 uses a single-channel LoRa module to minimize the deployment cost for a private p2p LoRa wireless network.
29 -
30 -(% style="color:red" %)**Note: The LG01v2 can't register and connect to the LoRaWAN server(Such as The Things NetWork, AWS, or Chirpstack..)**
28 +LG01v2 is specially design for (% style="color:blue" %)**peer to peer LoRa**(%%) protocol instead of LoRaWAN protocol. The LG01v2 use single channel LoRa module to minimize the deployment cost for a private p2p LoRa wireless network.
31 31  )))
32 32  
33 33  (((
... ... @@ -77,15 +77,21 @@
77 77  LG01-V2 has totally four LEDs, They are:
78 78  
79 79  
80 -(% style="color:blue" %)**➢ Power LED**[[image:image-20231014092959-4.png]](%%): This RED LED will be solid if the device is properly powered
78 +(% style="color:blue" %)**➢ Power LED**(%%): This RED LED will be solid if the device is properly powered
81 81  
82 -(% style="color:blue" %)**➢ ETH LED**[[image:image-20231014092934-2.png]](%%):  This RGB LED will blink GREEN when the ETH port is connecting
80 +(% style="color:blue" %)**➢ ETH LED**(%%):  This RGB LED will blink GREEN when the ETH port is connecting
83 83  
84 -(% style="color:blue" %)**➢ SYS LED**[[image:image-20231014092954-3.png]](%%):  Undefined yet. 
82 +(% style="color:blue" %)**➢ SYS LED**(%%):  This RGB LED will show different colors in different states:
85 85  
86 -(% style="color:blue" %)**➢ WIFI LED**[[image:image-20231014092843-1.png]](%%): This LED shows the WIFI interface connection status.
84 + ✓ **SOLID GREEN:** The device is alive with a LoRaWAN server connection.
87 87  
86 + ✓ **BLINKING GREEN:** a) Device has internet connection but no LoRaWAN Connection. or b) Device is in booting stage, in this stage, it will BLINKING GREEN for several seconds and then with BLINKING GREEN together
88 88  
88 + ✓** SOLID RED:** Device doesn't have an Internet connection.
89 +
90 +(% style="color:blue" %)**➢ WIFI LED**(%%): This LED shows the WIFI interface connection status.
91 +
92 +
89 89  == 1.6 Button Intruction ==
90 90  
91 91  
... ... @@ -520,37 +520,11 @@
520 520  LG01v2 supports system auto update via OTA, please see **[[this URL>>url:http://wiki.dragino.com/xwiki/bin/view/OTA%20Update/]]** for the detail of this feature.
521 521  
522 522  
523 -= 7. How users can access LG01v2 using serial USB =
527 += 7. FAQ =
524 524  
525 -**USB TTL to LG01v2  Connection:**
529 +== 7.1 How does LG01v2 communicate with Lora shield (LoRa.h) ==
526 526  
527 -Port 1 of the UART on the LG01v2 is GND
528 528  
529 -(% class="box infomessage" %)
530 -(((
531 -**TXD  <~-~--> UART RXD (Gray line)**
532 -
533 -**RXD  <~-~--> UART TXD (White line)**
534 -
535 -**GND <~-~--> GND (Black line)**
536 -)))
537 -
538 -**LG01v2 UART connection photo**
539 -
540 -[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20230421094319-2.png?width=392&height=351&rev=1.1||alt="image-20230421094319-2.png"]]
541 -
542 -In the PC,you can use the serial port tool(such as [[putty>>url:http://www.chiark.greenend.org.uk/~~sgtatham/putty/download.html]] in Windows), you need to set the serial baud rate to (% style="color:blue" %)**115200**(%%) to access the serial console for LPS8v2. LPS8v2 will output system info once power on as below:
543 -
544 -[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164928-3.png?width=332&height=320&rev=1.1||alt="image-20220804164928-3.png"]]
545 -
546 -[[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20All%20Gateway%20models/HP0C/WebHome/image-20220804164747-2.png?width=594&height=622&rev=1.1||alt="image-20220804164747-2.png"]]
547 -
548 -
549 -= 8. FAQ =
550 -
551 -== 8.1 How does LG01v2 communicate with Lora shield (LoRa.h) ==
552 -
553 -
554 554  This example describes how to use LG01v2, LoRa Shield to set up a LoRa network,
555 555  
556 556  [[image:image-20221103152238-8.png||height="251" width="654"]]
... ... @@ -597,7 +597,7 @@
597 597  [[image:image-20221101162527-4.png]]
598 598  
599 599  
600 -== 8.2 How does LG01v2 communicate with Heltec LoRa Node ==
578 +== 7.2 How does LG01v2 communicate with Heltec LoRa Node ==
601 601  
602 602  
603 603  This example describes how to use LG01v2 and Heltec LoRa Node to set up a LoRa network,
... ... @@ -638,7 +638,7 @@
638 638  [[image:image-20221112163119-4.png||height="808" width="560"]]
639 639  
640 640  
641 -== 8.3 How does LG01v2 communicate with LoRaWAN node ==
619 +== 7.3 How does LG01v2 communicate with LoRaWAN node ==
642 642  
643 643  
644 644  This example describes how to use LG01v2 and LSN50 to set up a  network,
... ... @@ -658,12 +658,8 @@
658 658  AT+SYNCWORD=1  ~-~-->  Syncword**(0: private，1: public), **the corresponding Lora shield syncword is 0x12
659 659  )))
660 660  
661 -**Step2:  **Run AT commands to make the LSN50 work in Single frequency and ABP mode.
639 +**Step2:  **Run AT commands to make the LSN50 work in Single frequency and ABP mode. Below are the AT commands:
662 662  
663 -For more information on how to use AT commands in LSN50v2, please refer to this link: [[LSN50v2-S31-S31B Use AT Command>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/#H4.A0UseATCommand]]
664 -
665 -Below are the AT commands:
666 -
667 667  (% class="box infomessage" %)
668 668  (((
669 669  AT+FDR  ~-~--> Reset Parameters to Factory Default, Keys Reserve
... ... @@ -699,7 +699,7 @@
699 699  [[image:image-20230620103923-3.png||height="476" width="1138"]]
700 700  
701 701  
702 -== 8.4 How can users factory reset LG01v2 ==
676 +== 7.4 How can users factory reset LG01v2 ==
703 703  
704 704  
705 705  Users can download the image of LG01v2 from this link：[[dragino-lg01v2-1.7-0210>>https://www.dropbox.com/scl/fi/g0si61lcrvdjyto4ma951/dragino-lg01v2-1.7-0210.zip?rlkey=t03oqo493r2p7ign488rs2jsv&dl=0]]
... ... @@ -710,9 +710,9 @@
710 710  [[How to flash a new image(OS) to the gateway>>url:https://wiki.dragino.com/xwiki/bin/view/Main/Armbian%20OS%20instruction/#H2.3A0Howtoflashanewimage28OS29tothegateway28LPS8V229]]
711 711  
712 712  
713 -= 9. Trouble Shooting =
687 += 8. Trouble Shooting =
714 714  
715 -== 9.1  Fallback IP does not work, how can users check ==
689 +== 8.1  Fallback IP does not work, how can users check ==
716 716  
717 717  
718 718  When the computer has completed the above fallback IP configuration,the LG01v2 Web UI is still not accessible via fallback IP.
... ... @@ -734,7 +734,7 @@
734 734  If the firewall is not down, this will affect access to the gateway.
735 735  
736 736  
737 -= (% style="color:inherit; font-family:inherit; font-size:29px" %)10. Supports(%%) =
711 += (% style="color:inherit; font-family:inherit; font-size:29px" %)9. Supports(%%) =
738 738  
739 739  
740 740  (((
... ... @@ -745,7 +745,7 @@
745 745  With your question as detailed as possible. We will reply and help you in the shortest.
746 746  
747 747  
748 -= 11. Reference =
722 += 10. Reference =
749 749  
750 750  
751 751  * Install Tago Core: Refer **Install Tago Core in LG01v2** in[[ Instruction>>doc:Main.Tago\.IO.WebHome]].
... ... @@ -755,7 +755,7 @@
755 755  
756 756  )))
757 757  
758 -= 12. Order Info =
732 += 11. Order Info =
759 759  
760 760  
761 761  (% style="color:#0000ff" %)**LG01v2-XXX-YYY**
... ... @@ -775,7 +775,7 @@
775 775  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
776 776  
777 777  
778 -= 13. Manufacturer Info =
752 += 12. Manufacturer Info =
779 779  
780 780  
781 781  **Shenzhen Dragino Technology Development co. LTD**
... ... @@ -785,7 +785,7 @@
785 785  LongCheng Street, LongGang District ; Shenzhen 518116,China
786 786  
787 787  
788 -= 14. FCC Warning =
762 += 13. FCC Warning =
789 789  
790 790  
791 791  (((
image-20231014092843-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -596 bytes
Content
image-20231014092934-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -620 bytes
Content
image-20231014092954-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -618 bytes
Content
image-20231014092959-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -563 bytes
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0