Changes for page DLOS8N - Outdoor LoRaWAN Gateway User Manual

Last modified by Kilight Cao on 2024/09/21 09:44

From version < 94.3 >

edited by Xiaoling
on 2022/07/06 14:04

To version < 93.4 >

edited by Xiaoling
on 2022/07/04 16:36

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -5,11 +5,6 @@
--
--
--
--
--
  **Table of Contents：**
  {{toc/}}
@@ -69,6 +69,7 @@
  * 16MB Flash
++
  **Interface:**
  * 10M/100M RJ45 Ports x 1
@@ -81,6 +81,7 @@
  * SX1302 + 2 x SX1250
++
  **WiFi Spec:**
  * IEEE 802.11 b/g/n
@@ -95,6 +95,7 @@
  ** 11n 20M : -67dbm
++
  **LoRa Spec:**
  * Up to -140 dBm sensitivity with SX1250 Tx/Rx front-end
@@ -107,6 +107,7 @@
  * True antenna diversity or simultaneous dual-band operation
++
  **Cellular 4G LTE (optional):**
  * Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
@@ -117,6 +117,7 @@
  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
++
  **Power over Ethernet:**
  * IEEE 802.3af compliant.
@@ -127,6 +127,9 @@
  * Isolation level 4 KVrms.
  * Enhanced surge protection
++
++
++
  == 1.3 Features ==
  * Open Source Embedded Linux system
@@ -146,6 +146,9 @@
  * Lighting Protection
  * Power Consumption:12v ,300-500mA
++
++
++
  == 1.4 Hardware System Structure ==
  [[image:1652411641871-482.png||height="416" width="716"]]
@@ -188,7 +188,6 @@
  [[image:1652412859663-161.png||height="341" width="333"]]
--
  = 2. Access and Configure DLOS8N =
  The DLOS8N is configured as a WiFi Access Point by default. User can access and configure the DLOS8N after connecting to its WiFi network, or via its Ethernet port.
@@ -218,7 +218,7 @@
  (((
--Alternatively, connect the DLOS8N Ethernet port to your router and DLOS8N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the DLOS8N. You can also use this IP to connect.
++Alternatively, connect the DLOS8N Ethernet port to your router and DLOS8N will obtain an IP address from your router. In the router’s management portal, you should be able to find what IP address the router has assigned to the DLOS8N. You can also use this IP to connect.
  )))
@@ -233,7 +233,7 @@
  === 2.1.4 Connect via Ethernet with fall back ip ===
--The WAN port also has a [[fall back ip address>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
++The WAN port also has a [[fall back ip address>>path:#_I_configured_LPS8]] for access if user doesn’t connect to uplink router. Click [[here>>path:#_I_configured_LPS8]] to see how to configure.
  == 2.2 Access Configure Web UI ==
@@ -259,7 +259,6 @@
  [[image:1652414287022-223.png]]
--
  = 3. Typical Network Setup =
  == 3.1 Overview ==
@@ -273,9 +273,10 @@
++
  == 3.2 Use WAN port to access Internet ==
--By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N's WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
++By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N’s WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
  [[image:1652420169255-959.png]]
@@ -331,8 +331,8 @@
  In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.
  * GREEN Tick  [[image:1652436675869-206.png||height="14" width="15"]]  : This interface has Internet connection.
--* Yellow  Tick  [[image:1652436705761-420.png||height="15" width="15"]]  : This interface has IP address but don't use it for internet connection.
--* RED Cross    [[image:1652436787176-950.png||height="14" width="15"]]  : This interface doesn't connected.
++* Yellow  Tick  [[image:1652436705761-420.png||height="15" width="15"]]  : This interface has IP address but don’t use it for internet connection.
++* RED Cross    [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn’t connected.
  [[image:1652421351382-793.png||height="339" width="765"]]
@@ -395,7 +395,6 @@
  [[image:1652422479876-297.png||height="398" width="729"]]
--
  (((
  (% style="color:red" %)**Notice: **Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.
  )))
@@ -421,7 +421,6 @@
  [[image:1652422624783-580.png||height="327" width="729"]]
--
  (% style="color:red" %)**Note: **The server address must match the Gateway server address you choose in TTN V3.
  In the home page, we can see the LoRaWAN connection is ready now.
@@ -470,8 +470,6 @@
  * APP Key - Unique key to secure communications with a particular device.
  (((
--
--
  A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.
  )))
@@ -507,21 +507,16 @@
  [[image:1652422998005-968.png||height="352" width="744"]]
--
  First, input the End device ID, AppEUI and DevEUI.
  [[image:1652423022781-339.png||height="365" width="741"]]
--
  Secondly, choose the corresponding frequency and LoRaWAN class capabilities.
  [[image:1652423046741-467.png||height="355" width="736"]]
--
  (((
  Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.
--
--
  )))
  (((
@@ -659,11 +659,11 @@
  )))
  (((
--**__Timezone: __**Set device timezone.
++**__Timezone:__**Set device timezone.
  )))
  (((
--**__Port forwarding: __**Enable/Disable the HTTP and SSH access via WAN interface.
++**__Port forwarding:__**Enable/Disable the HTTP and SSH access via WAN interface.
  )))
@@ -673,15 +673,15 @@
  [[image:1652429149053-824.png||height="467" width="725"]]
  (((
--**__LAN Settings:  __**When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N's own network.
++**__LAN Settings:__**When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N’s own network.
  )))
  (((
--__**WAN Settings: **__Setting for DLOS8N WAN port
++__**WAN Settings:**__Setting for DLOS8N WAN port
  )))
  (((
--__**WiFi Settings:  **__Setting for DLOS8N WiFi IP when use it as WiFi Client
++__**WiFi Settings:**__Setting for DLOS8N WiFi IP when use it as WiFi Client
  )))
@@ -699,7 +699,7 @@
  [[image:1652429309615-825.png||height="320" width="732"]]
--(% style="color:red" %)Note *: For DLOS8N which doesn't have the cellular module, this page will shows Cellular not detected.
++(% style="color:red" %)Note *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.
  === 5.5.6 System ~-~-> Network Status ===
@@ -737,12 +737,10 @@
  ( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )
--
  * **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].
  ( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )
--
  (((
  The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.
  )))
@@ -755,7 +755,6 @@
  Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.
--
  (% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
  The system will automatically boot into the new firmware after upgrade.
@@ -814,7 +814,6 @@
  [[image:1652430369760-511.png||height="373" width="730"]]
--
  = 6. More features =
  == 6.1 More instructions ==
@@ -937,8 +937,6 @@
  (((
  (% style="background-color:#dcdcdc" %)//Configuring iperf.//
--
--
  )))
  = 8. Upgrade Linux Firmware =
@@ -1023,21 +1023,15 @@
  (% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.
--(((
  Steps to connect via fall back IP:
--)))
--(((
--~1. Connect PC's Ethernet port to DLOS8N's WAN port
--)))
++~1. Connect PC’s Ethernet port to DLOS8N’s WAN port
--(((
--2. Configure PC's Ethernet port has IP: 172.31.255.253 and Netmask: 255.255.255.252
--)))
++2. Configure PC’s Ethernet port has
++    IP: 172.31.255.253 and
++    Netmask: 255.255.255.252
--(((
  As below photo:
--)))
  [[image:1652435256286-879.png]]
@@ -1052,20 +1052,19 @@
  (% style="color:#4f81bd" %) **//XXX: Frequency Band//**
--* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
--* (% style="color:red" %)** 915**(% style="color:black" %):  valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
++* (% style="color:#4f81bd" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
++* (% style="color:#4f81bd" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
  (% style="color:#4f81bd" %) **//YYY: 4G Cellular Option//**
--* (% style="color:red" %)** E**(% style="color:black" %):    EMEA, Korea, Thailand, India.
--* (% style="color:red" %)** A**(% style="color:black" %):   North America/ Rogers/AT&T/T-Mobile.
--* (% style="color:red" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
--* (% style="color:red" %)** J**(% style="color:black" %):    Japan, DOCOMO/SoftBank/ KDDI
++* (% style="color:#4f81bd" %)** E**(% style="color:black" %): EMEA, Korea, Thailand, India.
++* (% style="color:#4f81bd" %)** A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
++* (% style="color:#4f81bd" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
++* (% style="color:#4f81bd" %)** J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
--
  = 12. Packing Info =
  (((
@@ -1087,6 +1087,7 @@
++
  = 13. Support =
  * Try to see if your questions already answered in the [[wiki>>doc:Main.WebHome]].

Changes for page DLOS8N - Outdoor LoRaWAN Gateway User Manual

Summary

Details

Applications

Navigation