Last modified by Kilight Cao on 2024/09/21 09:44
<
From version < 94.2 >
edited by Xiaoling
on 2022/07/06 13:52
To version < 97.1 >
edited by Xiaoling
on 2022/07/06 14:11
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -5,6 +5,11 @@
5 5  
6 6  
7 7  
8 +
9 +
10 +
11 +
12 +
8 8  **Table of Contents：**
9 9  
10 10  {{toc/}}
... ... @@ -53,10 +53,10 @@
53 53  == 1.2 Specifications ==
54 54  
55 55  
56 -**Hardware System:**
61 +(% style="color:#037691" %)**Hardware System:**
57 57  
58 58  (((
59 - Linux Part:
64 +(% style="color:#037691" %)**Linux Part:**
60 60  )))
61 61  
62 62  * 400Mhz ar9331 processor
... ... @@ -63,9 +63,8 @@
63 63  * 64MB RAM
64 64  * 16MB Flash
65 65  
71 +(% style="color:#037691" %)**Interface:**
66 66  
67 -**Interface:**
68 -
69 69  * 10M/100M RJ45 Ports x 1
70 70  * WiFi : 802.11 b/g/n
71 71  * LoRaWAN Wireless
... ... @@ -75,9 +75,8 @@
75 75  * Mini-PCI E connector x 1
76 76  * SX1302 + 2 x SX1250
77 77  
82 +(% style="color:#037691" %)**WiFi Spec:**
78 78  
79 -**WiFi Spec:**
80 -
81 81  * IEEE 802.11 b/g/n
82 82  * Frequency Band: 2.4 ~~ 2.462GHz
83 83  * Tx power:
... ... @@ -89,9 +89,8 @@
89 89  ** 11g 54M : -71dbm
90 90  ** 11n 20M : -67dbm
91 91  
95 +(% style="color:#037691" %)**LoRa Spec:**
92 92  
93 -**LoRa Spec:**
94 -
95 95  * Up to -140 dBm sensitivity with SX1250 Tx/Rx front-end
96 96  * 70 dB CW interferer rejection at 1 MHz offset
97 97  * Able to operate with negative SNR, CCR up to 9dB
... ... @@ -101,9 +101,8 @@
101 101  * Dynamic data-rate (DDR) adaptation
102 102  * True antenna diversity or simultaneous dual-band operation
103 103  
106 +(% style="color:#037691" %)**Cellular 4G LTE (optional):**
104 104  
105 -**Cellular 4G LTE (optional):**
106 -
107 107  * Quectel: [[**EC25 LTE module**>>url:https://www.quectel.com/product/ec25minipcie.htm]]
108 108  * Standard Size SIM Slot
109 109  * 2 x 4G Sticker Antenna.
... ... @@ -111,9 +111,8 @@
111 111  * Worldwide LTE,UMTS/HSPA+ and GSM/GPRS/EDGE coverage
112 112  * MIMO technology meets demands for data rate and link reliability in modem wireless communication systems
113 113  
115 +(% style="color:#037691" %)**Power over Ethernet:**
114 114  
115 -**Power over Ethernet:**
116 -
117 117  * IEEE 802.3af compliant.
118 118  * Support wide input voltage range  37Vdc to 57Vdc.
119 119  * Thermal cut off.
... ... @@ -123,7 +123,6 @@
123 123  * Enhanced surge protection
124 124  
125 125  
126 -
127 127  == 1.3 Features ==
128 128  
129 129  * Open Source Embedded Linux system
... ... @@ -144,7 +144,6 @@
144 144  * Power Consumption:12v ,300-500mA
145 145  
146 146  
147 -
148 148  == 1.4 Hardware System Structure ==
149 149  
150 150  [[image:1652411641871-482.png||height="416" width="716"]]
... ... @@ -173,10 +173,9 @@
173 173  (% style="color:green" %)**BLINKING GREEN**:(% style="color:black" %) a) Device has internet connection but no LoRaWAN Connection.  or b) Device is in booting stage, in this stage, it will (% style="color:green" %)**BLINKING GREEN**(% style="color:black" %) for several seconds and then (% style="color:red" %)**RED** (% style="color:black" %)and (% style="color:#ffc000" %)**YELLOW** (% style="color:black" %)will blink together.
174 174  )))
175 175  * (((
176 -(% style="color:red" %)**SOLID RED**: (% style="color:black" %)Device doesn’t have Internet connection.
174 +(% style="color:red" %)**SOLID RED**: (% style="color:black" %)Device doesn't have Internet connection.
177 177  
178 178  
179 -
180 180  
181 181  )))
182 182  )))
... ... @@ -274,7 +274,7 @@
274 274  
275 275  == 3.2 Use WAN port to access Internet ==
276 276  
277 -By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N’s WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
274 +By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N's WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
278 278  
279 279  [[image:1652420169255-959.png]]
280 280  
... ... @@ -330,8 +330,8 @@
330 330  In the (% style="color:#4f81bd" %)**home**(%%) page, we can check the Internet connection.
331 331  
332 332  * GREEN Tick ​​​​ [[image:1652436675869-206.png||height="14" width="15"]] : This interface has Internet connection.
333 -* Yellow  Tick  [[image:1652436705761-420.png||height="15" width="15"]] : This interface has IP address but don’t use it for internet connection.
334 -* RED Cross    [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn’t connected.
330 +* Yellow  Tick  [[image:1652436705761-420.png||height="15" width="15"]] : This interface has IP address but don't use it for internet connection.
331 +* RED Cross    [[image:1652436787176-950.png||height="14" width="15"]] : This interface doesn't connected.
335 335  
336 336  [[image:1652421351382-793.png||height="339" width="765"]]
337 337  
... ... @@ -394,6 +394,7 @@
394 394  
395 395  [[image:1652422479876-297.png||height="398" width="729"]]
396 396  
394 +
397 397  (((
398 398  (% style="color:red" %)**Notice: **Gateway Server address must match the gateway configuration, otherwise you will have problem for End Node to join the network.
399 399  )))
... ... @@ -419,6 +419,7 @@
419 419  
420 420  [[image:1652422624783-580.png||height="327" width="729"]]
421 421  
420 +
422 422  (% style="color:red" %)**Note: **The server address must match the Gateway server address you choose in TTN V3.
423 423  
424 424  In the home page, we can see the LoRaWAN connection is ready now.
... ... @@ -467,6 +467,8 @@
467 467  * APP Key - Unique key to secure communications with a particular device.
468 468  
469 469  (((
469 +
470 +
470 470  A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.
471 471  )))
472 472  
... ... @@ -502,16 +502,21 @@
502 502  
503 503  [[image:1652422998005-968.png||height="352" width="744"]]
504 504  
506 +
505 505  First, input the End device ID, AppEUI and DevEUI.
506 506  
507 507  [[image:1652423022781-339.png||height="365" width="741"]]
508 508  
511 +
509 509  Secondly, choose the corresponding frequency and LoRaWAN class capabilities.
510 510  
511 511  [[image:1652423046741-467.png||height="355" width="736"]]
512 512  
516 +
513 513  (((
514 514  Finally, Application layer settings input the corresponding AppKey. Before saving the configuration, check that the data matches the device.
519 +
520 +
515 515  )))
516 516  
517 517  (((
... ... @@ -649,11 +649,11 @@
649 649  )))
650 650  
651 651  (((
652 -**__Timezone:__**Set device timezone.
658 +**__Timezone: __**Set device timezone.
653 653  )))
654 654  
655 655  (((
656 -**__Port forwarding:__**Enable/Disable the HTTP and SSH access via WAN interface.
662 +**__Port forwarding: __**Enable/Disable the HTTP and SSH access via WAN interface.
657 657  
658 658  
659 659  )))
... ... @@ -663,15 +663,15 @@
663 663  [[image:1652429149053-824.png||height="467" width="725"]]
664 664  
665 665  (((
666 -**__LAN Settings:__**When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N’s own network.
672 +**__LAN Settings:  __**When the DLOS8N has the AP enable, LAN settings specify the network info for DLOS8N's own network.
667 667  )))
668 668  
669 669  (((
670 -__**WAN Settings:**__Setting for DLOS8N WAN port
676 +__**WAN Settings: **__Setting for DLOS8N WAN port
671 671  )))
672 672  
673 673  (((
674 -__**WiFi Settings:**__Setting for DLOS8N WiFi IP when use it as WiFi Client
680 +__**WiFi Settings:  **__Setting for DLOS8N WiFi IP when use it as WiFi Client
675 675  
676 676  
677 677  )))
... ... @@ -689,7 +689,7 @@
689 689  
690 690  [[image:1652429309615-825.png||height="320" width="732"]]
691 691  
692 -(% style="color:red" %)Note *: For DLOS8N which doesn’t have the cellular module, this page will shows Cellular not detected.
698 +(% style="color:red" %)Note *: For DLOS8N which doesn't have the cellular module, this page will shows Cellular not detected.
693 693  
694 694  
695 695  === 5.5.6 System ~-~-> Network Status ===
... ... @@ -727,10 +727,12 @@
727 727  
728 728  ( [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LG02-OLG02/Firmware/]] )
729 729  
736 +
730 730  * **Change Log**: [[Firmware Change Log>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]].
731 731  
732 732  ( [[http:~~/~~/www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog>>url:http://www.dragino.com/downloads/downloads/LoRa_Gateway/LG02-OLG02/Firmware/ChangeLog]] )
733 733  
741 +
734 734  (((
735 735  The file named as (% style="color:green" %)**xxxxx–xxxxx-squashfs-sysupgrade.bin **(% style="color:black" %)is the upgrade Image. There are different methods to upgrade, as below.
736 736  )))
... ... @@ -743,6 +743,7 @@
743 743  
744 744  Select the required image and click **Flash Image.** The image will be uploaded to the device, and then click **Process Update** to upgrade.
745 745  
754 +
746 746  (% style="color:red" %)**NOTE**: (% style="color:black" %)You normally need to **//uncheck//** the **Preserve Settings** checkbox when doing an upgrade to ensure that there is no conflict between the old settings and the new firmware. The new firmware will start up with its default settings.
747 747  
748 748  The system will automatically boot into the new firmware after upgrade.
... ... @@ -801,6 +801,7 @@
801 801  
802 802  [[image:1652430369760-511.png||height="373" width="730"]]
803 803  
813 +
804 804  = 6. More features =
805 805  
806 806  == 6.1 More instructions ==
... ... @@ -923,6 +923,8 @@
923 923  
924 924  (((
925 925  (% style="background-color:#dcdcdc" %)//Configuring iperf.//
936 +
937 +
926 926  )))
927 927  
928 928  = 8. Upgrade Linux Firmware =
... ... @@ -1007,15 +1007,21 @@
1007 1007  (% style="color:red" %)Note: fallback IP can be disabled in the WAN and DHCP page.
1008 1008  
1009 1009  
1022 +(((
1010 1010  Steps to connect via fall back IP:
1024 +)))
1011 1011  
1026 +(((
1012 1012  ~1. Connect PC's Ethernet port to DLOS8N's WAN port
1028 +)))
1013 1013  
1014 -2. Configure PC's Ethernet port has
1015 - IP: 172.31.255.253 and
1016 - Netmask: 255.255.255.252
1030 +(((
1031 +2. Configure PC's Ethernet port has IP: 172.31.255.253 and Netmask: 255.255.255.252
1032 +)))
1017 1017  
1034 +(((
1018 1018  As below photo:
1036 +)))
1019 1019  
1020 1020  [[image:1652435256286-879.png]]
1021 1021  
... ... @@ -1030,19 +1030,20 @@
1030 1030  
1031 1031  (% style="color:#4f81bd" %) **//XXX: Frequency Band//**
1032 1032  
1033 -* (% style="color:#4f81bd" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1034 -* (% style="color:#4f81bd" %)** 915**(% style="color:black" %): valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1051 +* (% style="color:red" %)** 868**(% style="color:black" %) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1052 +* (% style="color:red" %)** 915**(% style="color:black" %):  valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1035 1035  
1036 1036  (% style="color:#4f81bd" %) **//YYY: 4G Cellular Option//**
1037 1037  
1038 -* (% style="color:#4f81bd" %)** E**(% style="color:black" %): EMEA, Korea, Thailand, India.
1039 -* (% style="color:#4f81bd" %)** A**(% style="color:black" %): North America/ Rogers/AT&T/T-Mobile.
1040 -* (% style="color:#4f81bd" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
1041 -* (% style="color:#4f81bd" %)** J**(% style="color:black" %): Japan, DOCOMO/SoftBank/ KDDI
1056 +* (% style="color:red" %)** E**(% style="color:black" %):  EMEA, Korea, Thailand, India.
1057 +* (% style="color:red" %)** A**(% style="color:black" %):  North America/ Rogers/AT&T/T-Mobile.
1058 +* (% style="color:red" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
1059 +* (% style="color:red" %)** J**(% style="color:black" %):  Japan, DOCOMO/SoftBank/ KDDI
1042 1042  
1043 1043  More info about valid bands, please see [[EC25-E product page>>url:https://www.quectel.com/product/ec25.htm]].
1044 1044  
1045 1045  
1064 +
1046 1046  = 12. Packing Info =
1047 1047  
1048 1048  (((

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0