<
From version < 192.2 >
edited by Xiaoling
on 2023/11/17 14:26
To version < 191.4 >
edited by Xiaoling
on 2023/06/10 16:52
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -119,6 +119,8 @@
119 119  * Isolation level 4 KVrms.
120 120  * Enhanced surge protection
121 121  
122 +
123 +
122 122  == 1.3 Features ==
123 123  
124 124  
... ... @@ -141,6 +141,8 @@
141 141  * Power Consumption:12v ,300-500mA
142 142  * Operating Temperature: -20~~85°C
143 143  
146 +
147 +
144 144  == 1.4 Hardware System Structure ==
145 145  
146 146  
... ... @@ -259,7 +259,7 @@
259 259  
260 260  
261 261  (((
262 -The WAN port also has a [[fall back ip address>>||anchor="H11.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H11.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
266 +The WAN port also has a [[fall back ip address>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
263 263  )))
264 264  
265 265  
... ... @@ -301,6 +301,8 @@
301 301  * **WiFi AP Mode**
302 302  * **Cellular Mode**
303 303  
308 +
309 +
304 304  == 3.2 Use WAN port to access Internet ==
305 305  
306 306  
... ... @@ -1021,7 +1021,7 @@
1021 1021  After updating the Chirpstack gateway-bridge firmware, there is no need to re-download and install the Chirpstack gateway-bridge package
1022 1022  
1023 1023  
1024 -== 6.6  How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive). ==
1030 +== 6.6 How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive). ==
1025 1025  
1026 1026  
1027 1027  USB card reader plugged into the USB port of the gateway.
... ... @@ -1056,7 +1056,7 @@
1056 1056  [[image:image-20230425173831-3.png||height="105" width="833"]]
1057 1057  
1058 1058  
1059 -== 6.7  How to view DLOS8N GPS information ==
1065 +== 6.7 How to view DLOS8N GPS information ==
1060 1060  
1061 1061  
1062 1062  By default, when the DLOS8N GPS positioning is complete, it will be displayed in the state package on the **LogRead ~-~-> System Log**  interface.
... ... @@ -1381,6 +1381,8 @@
1381 1381  
1382 1382  
1383 1383  As below photo:
1390 +
1391 +
1384 1384  )))
1385 1385  
1386 1386  [[image:1652435256286-879.png]]
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0