<
From version < 191.4 >
edited by Xiaoling
on 2023/06/10 16:52
To version < 192.2 >
edited by Xiaoling
on 2023/11/17 14:26
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -119,8 +119,6 @@
119 119  * Isolation level 4 KVrms.
120 120  * Enhanced surge protection
121 121  
122 -
123 -
124 124  == 1.3 Features ==
125 125  
126 126  
... ... @@ -143,8 +143,6 @@
143 143  * Power Consumption:12v ,300-500mA
144 144  * Operating Temperature: -20~~85°C
145 145  
146 -
147 -
148 148  == 1.4 Hardware System Structure ==
149 149  
150 150  
... ... @@ -263,7 +263,7 @@
263 263  
264 264  
265 265  (((
266 -The WAN port also has a [[fall back ip address>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
262 +The WAN port also has a [[fall back ip address>>||anchor="H11.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H11.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
267 267  )))
268 268  
269 269  
... ... @@ -305,8 +305,6 @@
305 305  * **WiFi AP Mode**
306 306  * **Cellular Mode**
307 307  
308 -
309 -
310 310  == 3.2 Use WAN port to access Internet ==
311 311  
312 312  
... ... @@ -1027,7 +1027,7 @@
1027 1027  After updating the Chirpstack gateway-bridge firmware, there is no need to re-download and install the Chirpstack gateway-bridge package
1028 1028  
1029 1029  
1030 -== 6.6 How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive). ==
1024 +== 6.6  How to extend the gateway size of memory with USB device (SD/TF card, USB flash drive). ==
1031 1031  
1032 1032  
1033 1033  USB card reader plugged into the USB port of the gateway.
... ... @@ -1062,7 +1062,7 @@
1062 1062  [[image:image-20230425173831-3.png||height="105" width="833"]]
1063 1063  
1064 1064  
1065 -== 6.7 How to view DLOS8N GPS information ==
1059 +== 6.7  How to view DLOS8N GPS information ==
1066 1066  
1067 1067  
1068 1068  By default, when the DLOS8N GPS positioning is complete, it will be displayed in the state package on the **LogRead ~-~-> System Log**  interface.
... ... @@ -1387,8 +1387,6 @@
1387 1387  
1388 1388  
1389 1389  As below photo:
1390 -
1391 -
1392 1392  )))
1393 1393  
1394 1394  [[image:1652435256286-879.png]]
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0