Skip to Content
Last modified by Kilight Cao on 2025/06/05 09:47
From version 139.7
edited by Xiaoling
on 2022/07/28 15:39
Change comment: There is no comment for this version
To version 139.18
edited by Xiaoling
on 2022/07/28 18:04
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -7,9 +7,6 @@
7 7  
8 8  
9 9  
10 -
11 -
12 -
13 13  **Table of Contents：**
14 14  
15 15  {{toc/}}
... ... @@ -21,10 +21,6 @@
21 21  
22 22  
23 23  
24 -
25 -
26 -
27 -
28 28  = 1. Introduction =
29 29  
30 30  == 1.1 What is the DLOS8N ==
... ... @@ -59,11 +59,15 @@
59 59  == 1.2 Specifications ==
60 60  
61 61  
55 +(((
62 62  (% style="color:#037691" %)**Hardware System:**
57 +)))
63 63  
64 64  (((
60 +(((
65 65  (% style="color:#037691" %)**Linux Part:**
66 66  )))
63 +)))
67 67  
68 68  * 400Mhz ar9331 processor
69 69  * 64MB RAM
... ... @@ -123,6 +123,8 @@
123 123  * Isolation level 4 KVrms.
124 124  * Enhanced surge protection
125 125  
123 +
124 +
126 126  == 1.3 Features ==
127 127  
128 128  
... ... @@ -143,6 +143,8 @@
143 143  * Lighting Protection
144 144  * Power Consumption:12v ,300-500mA
145 145  
145 +
146 +
146 146  == 1.4 Hardware System Structure ==
147 147  
148 148  
... ... @@ -197,6 +197,7 @@
197 197  The DLOS8N is configured as a WiFi Access Point by default. User can access and configure the DLOS8N after connecting to its WiFi network, or via its Ethernet port.
198 198  
199 199  
201 +
200 200  == 2.1 Find IP address of DLOS8N ==
201 201  
202 202  === 2.1.1 Connect via WiFi ===
... ... @@ -225,7 +225,9 @@
225 225  
226 226  
227 227  (((
230 +(((
228 228  Alternatively, connect the DLOS8N Ethernet port to your router and DLOS8N will obtain an IP address from your router. In the router's management portal, you should be able to find what IP address the router has assigned to the DLOS8N. You can also use this IP to connect.
232 +)))
229 229  
230 230  
231 231  
... ... @@ -244,7 +244,9 @@
244 244  === 2.1.4 Connect via Ethernet with fall back ip ===
245 245  
246 246  
251 +(((
247 247  The WAN port also has a [[fall back ip address>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] for access if user doesn't connect to uplink router. Click [[here>>||anchor="H10.3IconfiguredDLOS8NforWiFiaccessandlostitsIP.Whattodonow3F"]] to see how to configure.
253 +)))
248 248  
249 249  
250 250  
... ... @@ -287,10 +287,14 @@
287 287  * **WiFi AP Mode**
288 288  * **Cellular Mode**
289 289  
296 +
297 +
290 290  == 3.2 Use WAN port to access Internet ==
291 291  
292 292  
301 +(((
293 293  By default, the DLOS8N is set to use the WAN port to connect to an upstream network. When you connect the DLOS8N's WAN port to an upstream router, DLOS8N will get an IP address from the router and have Internet access via the upstream router. The network status can be checked in the (% style="color:#4f81bd" %)**home page**:
303 +)))
294 294  
295 295  [[image:1657089235431-309.png]]
296 296  
... ... @@ -299,11 +299,15 @@
299 299  == 3.3 Access the Internet as a WiFi Client ==
300 300  
301 301  
312 +(((
302 302  In the WiFi Client Mode, DLOS8N acts as a WiFi client and gets DHCP from an upstream router via WiFi.
314 +)))
303 303  
304 304  (((
317 +(((
305 305  The settings for WiFi Client is under page (% style="color:#4f81bd" %)**System~-~-> WiFi ~-~-> WiFi WAN Client Settings**
306 306  )))
320 +)))
307 307  
308 308  [[image:1657089014716-109.png]]
309 309  
... ... @@ -317,11 +317,15 @@
317 317  == 3.4 Access the Internet via Cellular ==
318 318  
319 319  
334 +(((
320 320  If the DLOS8N support 3G/4G Cellular modem option, When the label on the shell is displayed as Model : DLOS8N-EC25, it indicates that DLOS8 already has EC25 3G/4G modules,user can use it as main internet connection or back up.
336 +)))
321 321  
322 322  (((
339 +(((
323 323  First, release the four screws of DLOS8N, pull out PCB and install SIM card as below:
324 324  )))
342 +)))
325 325  
326 326  [[image:1652420606018-181.png]]
327 327  
... ... @@ -366,7 +366,9 @@
366 366  = 4. Example: Configure as a LoRaWAN gateway =
367 367  
368 368  
387 +(((
369 369  DLOS8N is fully compatible with LoRaWAN protocol. It uses the legacy Semtech Packet forwarder to forward the LoRaWAN packets to server. The structure is as below.
389 +)))
370 370  
371 371  (((
372 372  [[image:image-20220513140429-1.png||height="565" width="824"]]
... ... @@ -381,11 +381,15 @@
381 381  == 4.1 Create a gateway in TTN V3 Server ==
382 382  
383 383  
404 +(((
384 384  (% style="color:blue" %)**Step 1: Get a Unique gateway ID.**
406 +)))
385 385  
386 386  (((
409 +(((
387 387  Every DLOS8N has a unique gateway id. The ID can be found at LoRaWAN page:
388 388  )))
412 +)))
389 389  
390 390  (((
391 391  [[image:1652421929753-168.png||height="403" width="739"]]
... ... @@ -480,7 +480,9 @@
480 480  == 4.3 Configure frequency ==
481 481  
482 482  
507 +(((
483 483  We also need to set the frequency plan in DLOS8N to match the end node we use, so to receive the LoRaWAN packets from the LoRaWAN sensor.
509 +)))
484 484  
485 485  
486 486  [[image:1652422737399-529.png||height="362" width="737"]]
... ... @@ -520,8 +520,10 @@
520 520  (((
521 521  
522 522  
549 +(((
523 523  A set of these codes are stored in each device by the manufacturer as the default codes for that particular device. Each device is shipped with a sticker with the default Device EUI as shown below.
524 524  )))
552 +)))
525 525  
526 526  [[image:1652422840936-838.png]]
527 527  
... ... @@ -640,7 +640,9 @@
640 640  === 5.2.2 LoRa ~-~-> ABP Decryption ===
641 641  
642 642  
671 +(((
643 643  The DLOS8N can communicate with LoRaWAN ABP End Node without the need of LoRaWAN server. It can be used in some cases such as:
673 +)))
644 644  
645 645  * No internet connection.
646 646  * User wants to get data forward in gateway and forward to their server based on MQTT/HTTP, etc. (Combine ABP communication method and [[MQTT forward together>>doc:Main.MQTT Forward Instruction.WebHome]]).
... ... @@ -823,7 +823,7 @@
823 823  )))
824 824  
825 825  
826 -R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Remote Access Gateway.WebHome]]**
856 +R-SSH is for remote access device and management, introduction for how to use: **[[Remote Access Gateway>>doc:Main.Monitor & Remote Access Gateway.WebHome]]**
827 827  
828 828  [[image:1657090254561-321.png]]
829 829  
... ... @@ -1001,7 +1001,9 @@
1001 1001  == 7.4 Package maintenance system ==
1002 1002  
1003 1003  
1034 +(((
1004 1004  DLOS8N uses the OpenWrt [[**OPKG package maintenance system**>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]. There are more than 3000+ packages available in our package server for users to install for their applications. For example, if you want to add the **//iperf //** tool, you can install the related packages and configure DLOS8N to use **//iperf //**.
1036 +)))
1005 1005  
1006 1006  (((
1007 1007  Below are some example **//opkg //** commands. For more information please refer to the [[OPKG package maintain system>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]]** **([[https:~~/~~/oldwiki.archive.openwrt.org/doc/techref/opkg>>https://oldwiki.archive.openwrt.org/doc/techref/opkg]])
... ... @@ -1079,7 +1079,9 @@
1079 1079  == 9.2 Can I connect DLOS8N to LORIOT? ==
1080 1080  
1081 1081  
1114 +(((
1082 1082  Yes, the set up instruction is here: **[[Notes for LORIOT>>doc:Main.Notes for LORIOT.WebHome]]**
1116 +)))
1083 1083  
1084 1084  
1085 1085  
... ... @@ -1155,7 +1155,9 @@
1155 1155  
1156 1156  )))
1157 1157  
1192 +(((
1158 1158  (% style="color:red" %)**Note: fallback IP can be disabled in the WAN and DHCP page.**
1194 +)))
1159 1159  
1160 1160  
1161 1161  (((
... ... @@ -1191,15 +1191,13 @@
1191 1191  
1192 1192   **//PART: (% style="color:blue" %)DLOS8N-XXX-YYY//(%%)**
1193 1193  
1194 -**//XXX: Frequency Band//**
1230 +(% style="color:blue" %)**//XXX~://**(%%)**// Frequency Band//**
1195 1195  
1196 1196  * (% style="color:red" %)** 868**(%%) : valid frequency: 863Mhz ~~ 870Mhz. for bands EU868, RU864, IN865 or KZ865.
1197 1197  * (% style="color:red" %)** 915**(%%):  valid frequency: 902Mhz ~~ 928Mhz. for bands US915, AU915, AS923 or KR920
1198 1198  
1235 +(% style="color:blue" %)**//YYY~://**(%%)**// 4G Cellular Option//**
1199 1199  
1200 -
1201 -**//YYY: 4G Cellular Option//**
1202 -
1203 1203  * (% style="color:red" %)** E**(% style="color:black" %):  EMEA, Korea, Thailand, India.
1204 1204  * (% style="color:red" %)** A**(% style="color:black" %):  North America/ Rogers/AT&T/T-Mobile.
1205 1205  * (% style="color:red" %)** AU**(% style="color:black" %): Latin America, New Zeland, Taiwan
... ... @@ -1220,8 +1220,6 @@
1220 1220  * Stick Antenna for LoRa RF part. Frequency is one of 470 or 868 or 915Mhz depends the model ordered
1221 1221  * Packaging with environmental protection paper box
1222 1222  
1223 -
1224 -
1225 1225  (((
1226 1226  **Dimension and weight**:
1227 1227  )))
... ... @@ -1233,8 +1233,6 @@
1233 1233  
1234 1234  
1235 1235  
1236 -
1237 -
1238 1238  = 13. Support =
1239 1239  
1240 1240