Wiki source code of Update Firmware for the AI Sensors
Version 40.1 by Karry Zhuang on 2024/04/28 10:01
Show last authors
| author | version | line-number | content |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | **Table of Contents:** | ||
| 5 | |||
| 6 | {{toc/}} | ||
| 7 | |||
| 8 | |||
| 9 | |||
| 10 | |||
| 11 | |||
| 12 | |||
| 13 | |||
| 14 | = 1. Prepare Hardware & Software = | ||
| 15 | |||
| 16 | * Update Tool:[[OTA_Tool>>https://www.dropbox.com/scl/fi/d0tephd9ttghwf1ednj2s/OTA_Tool.rar?rlkey=sll5ny1fikqc8l0se9c4egxzs&st=f3ml8mop&dl=0]] | ||
| 17 | * Hardware: AIS Sensor, AUC USB TTL Adapter for AIS Sensors, PC | ||
| 18 | * Firmware:[[Digital wheel dial firmware>>https://www.dropbox.com/scl/fi/nxa0nw0k2qhbpcxzfsz03/Digital-table-wheel-firmware.rar?rlkey=u9wqmilfwu899fhc9i2jfcwou&st=ftsl46f5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=5m196s89&dl=0]] | ||
| 19 | |||
| 20 | = 2. Hardware Connection = | ||
| 21 | |||
| 22 | The AI Sensors and UART are connected and then connected to the PC. | ||
| 23 | |||
| 24 | [[image:image-20240424145937-3.png||height="629" width="544"]] | ||
| 25 | |||
| 26 | [[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]] | ||
| 27 | |||
| 28 | = 3.OTA UART flash = | ||
| 29 | |||
| 30 | Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder. | ||
| 31 | |||
| 32 | [[image:1713510920220-760.png||height="219" width="816"]] | ||
| 33 | |||
| 34 | The OTA_Tool folder should be opened and the program can be run by double-clicking on ota.exe. | ||
| 35 | |||
| 36 | [[image:1713511385474-910.png||height="452" width="804"]] | ||
| 37 | |||
| 38 | When the program opens, follow these steps. | ||
| 39 | |||
| 40 | 1 Select the chip type. AIS uses QFN72. Press 2 to select QFN72 | ||
| 41 | |||
| 42 | 2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol | ||
| 43 | |||
| 44 | 3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17 | ||
| 45 | |||
| 46 | 4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600 | ||
| 47 | |||
| 48 | [[image:1713511914316-181.png||height="754" width="865"]] | ||
| 49 | After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct. | ||
| 50 | |||
| 51 | [[image:1713513351848-254.png||height="477" width="861"]]x | ||
| 52 | |||
| 53 | Select 1 to check whether the configured port is correct. | ||
| 54 | |||
| 55 | [[image:1713513373484-487.png||height="472" width="856"]] | ||
| 56 | |||
| 57 | Select 2 is port is after normal communication with AIS. | ||
| 58 | |||
| 59 | [[image:1713513478607-793.png||height="471" width="851"]] | ||
| 60 | |||
| 61 | Press 0, press Enter, and select 2 to go to the upgrade surface. | ||
| 62 | |||
| 63 | [[image:1713513522820-547.png||height="467" width="847"]] | ||
| 64 | |||
| 65 | [[image:1713513544122-175.png||height="467" width="845"]] | ||
| 66 | |||
| 67 | Select 2 to enter the upgrade. | ||
| 68 | |||
| 69 | [[image:1713513668777-698.png||height="464" width="840"]] | ||
| 70 | |||
| 71 | If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds. | ||
| 72 | |||
| 73 | [[image:1713513732175-702.png||height="354" width="836"]] |