Wiki source code of Update Firmware for the AI Sensors
Version 38.1 by Karry Zhuang on 2024/04/26 15:04
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
36.2 | 1 | |
| |
36.1 | 2 | |
| 3 | |||
| 4 | **Table of Contents:** | ||
| 5 | |||
| 6 | {{toc/}} | ||
| 7 | |||
| 8 | |||
| 9 | |||
| 10 | |||
| 11 | |||
| 12 | |||
| 13 | |||
| |
26.1 | 14 | = 1. Prepare Hardware & Software = |
 |
2.1 | 15 | |
| |
36.2 | 16 | * Update Tool:[[OTA_Tool>>https://www.dropbox.com/scl/fi/d0tephd9ttghwf1ednj2s/OTA_Tool.rar?rlkey=sll5ny1fikqc8l0se9c4egxzs&st=f3ml8mop&dl=0]] |
| |
2.1 | 17 | * Hardware: Sensor, Converter |
| |
38.1 | 18 | * Firmware:[[Digital wheel dial firmware>>https://www.dropbox.com/scl/fi/nxa0nw0k2qhbpcxzfsz03/Digital-table-wheel-firmware.rar?rlkey=u9wqmilfwu899fhc9i2jfcwou&st=ftsl46f5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=5m196s89&dl=0]] |
| |
2.1 | 19 | |
| |
26.1 | 20 | = 2. Hardware Connection = |
| |
2.1 | 21 | |
| |
34.2 | 22 | The AI Sensors and UART are connected and then connected to the PC. |
| |
2.1 | 23 | |
| |
34.2 | 24 | [[image:image-20240424145937-3.png||height="629" width="544"]] |
| 25 | |||
| |
33.2 | 26 | [[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]] |
| |
25.1 | 27 | |
| |
26.1 | 28 | = 3.OTA UART flash = |
| |
25.1 | 29 | |
| 30 | Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder. | ||
| 31 | |||
| 32 | [[image:1713510920220-760.png||height="219" width="816"]] | ||
| 33 | |||
| 34 | The OTA_Tool folder should be opened and the program can be run by double-clicking on ota.exe. | ||
| 35 | |||
| 36 | [[image:1713511385474-910.png||height="452" width="804"]] | ||
| 37 | |||
| 38 | When the program opens, follow these steps. | ||
| 39 | |||
| 40 | 1 Select the chip type. AIS uses QFN72. Press 2 to select QFN72 | ||
| 41 | |||
| 42 | 2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol | ||
| 43 | |||
| |
31.1 | 44 | 3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17 |
| |
25.1 | 45 | |
| 46 | 4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600 | ||
| 47 | |||
| |
27.1 | 48 | [[image:1713511914316-181.png||height="754" width="865"]] |
| |
25.1 | 49 | After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct. |
| 50 | |||
| |
27.1 | 51 | [[image:1713513351848-254.png||height="477" width="861"]]x |
| |
25.1 | 52 | |
| 53 | Select 1 to check whether the configured port is correct. | ||
| 54 | |||
| |
27.1 | 55 | [[image:1713513373484-487.png||height="472" width="856"]] |
| |
25.1 | 56 | |
| 57 | Select 2 is port is after normal communication with AIS. | ||
| 58 | |||
| |
27.1 | 59 | [[image:1713513478607-793.png||height="471" width="851"]] |
| |
25.1 | 60 | |
| 61 | Press 0, press Enter, and select 2 to go to the upgrade surface. | ||
| 62 | |||
| |
27.1 | 63 | [[image:1713513522820-547.png||height="467" width="847"]] |
| |
25.1 | 64 | |
| |
27.1 | 65 | [[image:1713513544122-175.png||height="467" width="845"]] |
| |
25.1 | 66 | |
| 67 | Select 2 to enter the upgrade. | ||
| 68 | |||
| |
27.1 | 69 | [[image:1713513668777-698.png||height="464" width="840"]] |
| |
25.1 | 70 | |
| 71 | If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds. | ||
| 72 | |||
| |
27.1 | 73 | [[image:1713513732175-702.png||height="354" width="836"]] |