Wiki source code of Update Firmware for the AI Sensors
Version 33.2 by Karry Zhuang on 2024/04/24 14:59
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
26.1 | 1 | = 1. Prepare Hardware & Software = |
 |
2.1 | 2 | |
| |
29.1 | 3 | * Update Tool:OTA_Tool |
| |
2.1 | 4 | * Hardware: Sensor, Converter |
| 5 | * Firmware: | ||
| 6 | |||
| |
26.1 | 7 | = 2. Hardware Connection = |
| |
2.1 | 8 | |
| |
25.1 | 9 | The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side. |
| |
2.1 | 10 | |
| |
33.2 | 11 | [[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]] |
| |
25.1 | 12 | |
| |
26.1 | 13 | = 3.OTA UART flash = |
| |
25.1 | 14 | |
| 15 | Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder. | ||
| 16 | |||
| 17 | [[image:1713510920220-760.png||height="219" width="816"]] | ||
| 18 | |||
| 19 | The OTA_Tool folder should be opened and the program can be run by double-clicking on ota.exe. | ||
| 20 | |||
| 21 | [[image:1713511385474-910.png||height="452" width="804"]] | ||
| 22 | |||
| 23 | When the program opens, follow these steps. | ||
| 24 | |||
| 25 | 1 Select the chip type. AIS uses QFN72. Press 2 to select QFN72 | ||
| 26 | |||
| 27 | 2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol | ||
| 28 | |||
| |
31.1 | 29 | 3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17 |
| |
25.1 | 30 | |
| 31 | 4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600 | ||
| 32 | |||
| |
27.1 | 33 | [[image:1713511914316-181.png||height="754" width="865"]] |
| |
25.1 | 34 | After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct. |
| 35 | |||
| |
27.1 | 36 | [[image:1713513351848-254.png||height="477" width="861"]]x |
| |
25.1 | 37 | |
| 38 | Select 1 to check whether the configured port is correct. | ||
| 39 | |||
| |
27.1 | 40 | [[image:1713513373484-487.png||height="472" width="856"]] |
| |
25.1 | 41 | |
| 42 | Select 2 is port is after normal communication with AIS. | ||
| 43 | |||
| |
27.1 | 44 | [[image:1713513478607-793.png||height="471" width="851"]] |
| |
25.1 | 45 | |
| 46 | Press 0, press Enter, and select 2 to go to the upgrade surface. | ||
| 47 | |||
| |
27.1 | 48 | [[image:1713513522820-547.png||height="467" width="847"]] |
| |
25.1 | 49 | |
| |
27.1 | 50 | [[image:1713513544122-175.png||height="467" width="845"]] |
| |
25.1 | 51 | |
| 52 | Select 2 to enter the upgrade. | ||
| 53 | |||
| |
27.1 | 54 | [[image:1713513668777-698.png||height="464" width="840"]] |
| |
25.1 | 55 | |
| 56 | If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds. | ||
| 57 | |||
| |
27.1 | 58 | [[image:1713513732175-702.png||height="354" width="836"]] |