Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 38.1
edited by Karry Zhuang
on 2024/04/26 15:04
Change comment: There is no comment for this version
To version 26.1
edited by Karry Zhuang
on 2024/04/19 16:19
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,30 +14,15 @@
1 -
2 -
3 -
4 -**Table of Contents:**
5 -
6 -{{toc/}}
7 -
8 -
9 -
10 -
11 -
12 -
13 -
14 14  = 1. Prepare Hardware & Software =
15 15  
16 -* Update Tool:[[OTA_Tool>>https://www.dropbox.com/scl/fi/d0tephd9ttghwf1ednj2s/OTA_Tool.rar?rlkey=sll5ny1fikqc8l0se9c4egxzs&st=f3ml8mop&dl=0]]
3 +* Update Tool:
17 17  * Hardware: Sensor, Converter
18 -* Firmware:[[Digital wheel dial firmware>>https://www.dropbox.com/scl/fi/nxa0nw0k2qhbpcxzfsz03/Digital-table-wheel-firmware.rar?rlkey=u9wqmilfwu899fhc9i2jfcwou&st=ftsl46f5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=5m196s89&dl=0]]
5 +* Firmware:
19 19  
20 20  = 2. Hardware Connection =
21 21  
22 -The AI Sensors and UART are connected and then connected to the PC.
9 +The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side.
23 23  
24 -[[image:image-20240424145937-3.png||height="629" width="544"]]
11 +[[image:image-20240419145552-1.jpeg||height="399" width="476"]] [[image:image-20240419145552-2.jpeg||height="395" width="395"]]
25 25  
26 -[[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
27 -
28 28  = 3.OTA UART flash =
29 29  
30 30  Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
... ... @@ -41,33 +41,36 @@
41 41  
42 42  2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
43 43  
44 -3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17
29 +3 Select a port number. For example, the serial port number is COM17. Press 1 to select COM17
45 45  
46 46  4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
47 47  
48 -[[image:1713511914316-181.png||height="754" width="865"]]
33 +[[image:1713511914316-181.png||height="664" width="761"]]
49 49  After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
50 50  
51 -[[image:1713513351848-254.png||height="477" width="861"]]x
36 +[[image:1713513351848-254.png||height="428" width="773"]]x
52 52  
53 53  Select 1 to check whether the configured port is correct.
54 54  
55 -[[image:1713513373484-487.png||height="472" width="856"]]
40 +[[image:1713513373484-487.png]]
56 56  
57 57  Select 2 is port is after normal communication with AIS.
58 58  
59 -[[image:1713513478607-793.png||height="471" width="851"]]
44 +[[image:1713513478607-793.png||height="428" width="773"]]
60 60  
61 61  Press 0, press Enter, and select 2 to go to the upgrade surface.
62 62  
63 -[[image:1713513522820-547.png||height="467" width="847"]]
48 +[[image:1713513522820-547.png||height="426" width="773"]]
64 64  
65 -[[image:1713513544122-175.png||height="467" width="845"]]
50 +[[image:1713513544122-175.png||height="426" width="771"]]
66 66  
67 67  Select 2 to enter the upgrade.
68 68  
69 -[[image:1713513668777-698.png||height="464" width="840"]]
54 +[[image:1713513668777-698.png||height="429" width="776"]]
70 70  
71 71  If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
72 72  
73 -[[image:1713513732175-702.png||height="354" width="836"]]
58 +[[image:1713513732175-702.png||height="327" width="772"]]
59 +
60 +
61 +
image-20240424145824-1.gif
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 MB
Content
image-20240424145847-2.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -3.1 MB
Content
image-20240424145937-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 MB
Content
layout.bin
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -192 bytes
Content