Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 36.1
edited by Karry Zhuang
on 2024/04/26 14:37
Change comment: There is no comment for this version
To version 26.1
edited by Karry Zhuang
on 2024/04/19 16:19
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,31 +15,15 @@
1 -
2 -
3 -
4 -
5 -**Table of Contents:**
6 -
7 -{{toc/}}
8 -
9 -
10 -
11 -
12 -
13 -
14 -
15 15  = 1. Prepare Hardware & Software =
16 16  
17 -* Update Tool:OTA_Tool
3 +* Update Tool:
18 18  * Hardware: Sensor, Converter
19 19  * Firmware:
20 20  
21 21  = 2. Hardware Connection =
22 22  
23 -The AI Sensors and UART are connected and then connected to the PC.
9 +The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side.
24 24  
25 -[[image:image-20240424145937-3.png||height="629" width="544"]]
11 +[[image:image-20240419145552-1.jpeg||height="399" width="476"]] [[image:image-20240419145552-2.jpeg||height="395" width="395"]]
26 26  
27 -[[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
28 -
29 29  = 3.OTA UART flash =
30 30  
31 31  Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
... ... @@ -42,33 +42,36 @@
42 42  
43 43  2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
44 44  
45 -3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17
29 +3 Select a port number. For example, the serial port number is COM17. Press 1 to select COM17
46 46  
47 47  4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
48 48  
49 -[[image:1713511914316-181.png||height="754" width="865"]]
33 +[[image:1713511914316-181.png||height="664" width="761"]]
50 50  After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
51 51  
52 -[[image:1713513351848-254.png||height="477" width="861"]]x
36 +[[image:1713513351848-254.png||height="428" width="773"]]x
53 53  
54 54  Select 1 to check whether the configured port is correct.
55 55  
56 -[[image:1713513373484-487.png||height="472" width="856"]]
40 +[[image:1713513373484-487.png]]
57 57  
58 58  Select 2 is port is after normal communication with AIS.
59 59  
60 -[[image:1713513478607-793.png||height="471" width="851"]]
44 +[[image:1713513478607-793.png||height="428" width="773"]]
61 61  
62 62  Press 0, press Enter, and select 2 to go to the upgrade surface.
63 63  
64 -[[image:1713513522820-547.png||height="467" width="847"]]
48 +[[image:1713513522820-547.png||height="426" width="773"]]
65 65  
66 -[[image:1713513544122-175.png||height="467" width="845"]]
50 +[[image:1713513544122-175.png||height="426" width="771"]]
67 67  
68 68  Select 2 to enter the upgrade.
69 69  
70 -[[image:1713513668777-698.png||height="464" width="840"]]
54 +[[image:1713513668777-698.png||height="429" width="776"]]
71 71  
72 72  If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
73 73  
74 -[[image:1713513732175-702.png||height="354" width="836"]]
58 +[[image:1713513732175-702.png||height="327" width="772"]]
59 +
60 +
61 +
image-20240424145824-1.gif
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 MB
Content
image-20240424145847-2.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -3.1 MB
Content
image-20240424145937-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 MB
Content
layout.bin
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -192 bytes
Content