Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 35.1
edited by Karry Zhuang
on 2024/04/24 17:19
Change comment: There is no comment for this version
To version 25.1
edited by Karry Zhuang
on 2024/04/19 16:18
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,19 +1,17 @@
1 -= 1. Prepare Hardware & Software =
1 +~1. Prepare Hardware & Software
2 2  
3 -* Update Tool:OTA_Tool
3 +* Update Tool:
4 4  * Hardware: Sensor, Converter
5 5  * Firmware:
6 6  
7 -= 2. Hardware Connection =
7 +2. Hardware Connection
8 8  
9 -The AI Sensors and UART are connected and then connected to the PC.
9 +The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side.
10 10  
11 -[[image:image-20240424145937-3.png||height="629" width="544"]]
11 +[[image:image-20240419145552-1.jpeg||height="399" width="476"]] [[image:image-20240419145552-2.jpeg||height="395" width="395"]]
12 12  
13 -[[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
13 +3.OTA UART flash
14 14  
15 -= 3.OTA UART flash =
16 -
17 17  Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
18 18  
19 19  [[image:1713510920220-760.png||height="219" width="816"]]
... ... @@ -28,33 +28,36 @@
28 28  
29 29  2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
30 30  
31 -3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17
29 +3 Select a port number. For example, the serial port number is COM17. Press 1 to select COM17
32 32  
33 33  4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
34 34  
35 -[[image:1713511914316-181.png||height="754" width="865"]]
33 +[[image:1713511914316-181.png||height="664" width="761"]]
36 36  After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
37 37  
38 -[[image:1713513351848-254.png||height="477" width="861"]]x
36 +[[image:1713513351848-254.png||height="428" width="773"]]x
39 39  
40 40  Select 1 to check whether the configured port is correct.
41 41  
42 -[[image:1713513373484-487.png||height="472" width="856"]]
40 +[[image:1713513373484-487.png]]
43 43  
44 44  Select 2 is port is after normal communication with AIS.
45 45  
46 -[[image:1713513478607-793.png||height="471" width="851"]]
44 +[[image:1713513478607-793.png||height="428" width="773"]]
47 47  
48 48  Press 0, press Enter, and select 2 to go to the upgrade surface.
49 49  
50 -[[image:1713513522820-547.png||height="467" width="847"]]
48 +[[image:1713513522820-547.png||height="426" width="773"]]
51 51  
52 -[[image:1713513544122-175.png||height="467" width="845"]]
50 +[[image:1713513544122-175.png||height="426" width="771"]]
53 53  
54 54  Select 2 to enter the upgrade.
55 55  
56 -[[image:1713513668777-698.png||height="464" width="840"]]
54 +[[image:1713513668777-698.png||height="429" width="776"]]
57 57  
58 58  If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
59 59  
60 -[[image:1713513732175-702.png||height="354" width="836"]]
58 +[[image:1713513732175-702.png||height="327" width="772"]]
59 +
60 +
61 +
image-20240424145824-1.gif
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 MB
Content
image-20240424145847-2.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -3.1 MB
Content
image-20240424145937-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 MB
Content
layout.bin
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.karry
Size
... ... @@ -1,1 +1,0 @@
1 -192 bytes
Content