Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 34.1
edited by Karry Zhuang
on 2024/04/24 14:59
Change comment: Uploaded new attachment "image-20240424145937-3.png", version {1}
To version 43.2
edited by Xiaoling
on 2024/05/17 10:53
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.karry
1 +XWiki.Xiaoling
Content
... ... @@ -1,17 +1,38 @@
1 +
2 +
3 +
4 +**Table of Contents:**
5 +
6 +{{toc/}}
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 1  = 1. Prepare Hardware & Software =
2 2  
3 -* Update Tool:OTA_Tool
4 -* Hardware: Sensor, Converter
5 -* Firmware:
6 6  
17 +* Update Tool:[[OTA_Tool>>https://www.dropbox.com/scl/fi/d0tephd9ttghwf1ednj2s/OTA_Tool.rar?rlkey=sll5ny1fikqc8l0se9c4egxzs&st=f3ml8mop&dl=0]]
18 +* Hardware: AIS Sensor, AUC USB TTL Adapter for AIS Sensors, PC
19 +* Firmware:[[Digital wheel dial firmware>>https://www.dropbox.com/scl/fi/nxa0nw0k2qhbpcxzfsz03/Digital-table-wheel-firmware.rar?rlkey=u9wqmilfwu899fhc9i2jfcwou&st=ftsl46f5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=5m196s89&dl=0]]
20 +
21 +
22 +
7 7  = 2. Hardware Connection =
8 8  
9 -The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side.
10 10  
26 +The AIS Sensors and AUC USB TTL Adapter for AIS Sensors are connected and then connected to the PC.
27 +
28 +[[image:image-20240428155042-1.png||height="598" width="506"]]
29 +
11 11  [[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
12 12  
32 +
13 13  = 3.OTA UART flash =
14 14  
35 +
15 15  Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
16 16  
17 17  [[image:1713510920220-760.png||height="219" width="816"]]
... ... @@ -26,23 +26,28 @@
26 26  
27 27  2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
28 28  
29 -3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17
50 +3 Select a port number.The instance device port number is 17.Press 1 to select COM17
30 30  
31 31  4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
32 32  
33 33  [[image:1713511914316-181.png||height="754" width="865"]]
55 +
56 +
34 34  After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
35 35  
36 36  [[image:1713513351848-254.png||height="477" width="861"]]x
37 37  
61 +
38 38  Select 1 to check whether the configured port is correct.
39 39  
40 40  [[image:1713513373484-487.png||height="472" width="856"]]
41 41  
66 +
42 42  Select 2 is port is after normal communication with AIS.
43 43  
44 44  [[image:1713513478607-793.png||height="471" width="851"]]
45 45  
71 +
46 46  Press 0, press Enter, and select 2 to go to the upgrade surface.
47 47  
48 48  [[image:1713513522820-547.png||height="467" width="847"]]
... ... @@ -49,6 +49,7 @@
49 49  
50 50  [[image:1713513544122-175.png||height="467" width="845"]]
51 51  
78 +
52 52  Select 2 to enter the upgrade.
53 53  
54 54  [[image:1713513668777-698.png||height="464" width="840"]]
image-20240428155042-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +3.1 MB
Content