Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 28.1
edited by Karry Zhuang
on 2024/04/22 17:23
Change comment: There is no comment for this version
To version 24.1
edited by Karry Zhuang
on 2024/04/19 16:02
Change comment: Uploaded new attachment "1713513732175-702.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -1,59 +1,10 @@
1 -= 1. Prepare Hardware & Software =
1 +~1. Prepare Hardware & Software
2 2  
3 -* Update Tool:
3 +* Update Tool
4 4  * Hardware: Sensor, Converter
5 -* Software:
6 6  * Firmware:
7 7  
8 -= 2. Hardware Connection =
9 9  
10 -The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side.
8 +~1. Hardware Connection
11 11  
12 -[[image:image-20240419145552-1.jpeg||height="399" width="476"]] [[image:image-20240419145552-2.jpeg||height="395" width="395"]]
13 -
14 -= 3.OTA UART flash =
15 -
16 -Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
17 -
18 -[[image:1713510920220-760.png||height="219" width="816"]]
19 -
20 -The OTA_Tool folder should be opened and the program can be run by double-clicking on ota.exe.
21 -
22 -[[image:1713511385474-910.png||height="452" width="804"]]
23 -
24 -When the program opens, follow these steps.
25 -
26 -1 Select the chip type. AIS uses QFN72. Press 2 to select QFN72
27 -
28 -2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
29 -
30 -3 Select a port number. For example, the serial port number is COM17. Press 1 to select COM17
31 -
32 -4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
33 -
34 -[[image:1713511914316-181.png||height="754" width="865"]]
35 -After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
36 -
37 -[[image:1713513351848-254.png||height="477" width="861"]]x
38 -
39 -Select 1 to check whether the configured port is correct.
40 -
41 -[[image:1713513373484-487.png||height="472" width="856"]]
42 -
43 -Select 2 is port is after normal communication with AIS.
44 -
45 -[[image:1713513478607-793.png||height="471" width="851"]]
46 -
47 -Press 0, press Enter, and select 2 to go to the upgrade surface.
48 -
49 -[[image:1713513522820-547.png||height="467" width="847"]]
50 -
51 -[[image:1713513544122-175.png||height="467" width="845"]]
52 -
53 -Select 2 to enter the upgrade.
54 -
55 -[[image:1713513668777-698.png||height="464" width="840"]]
56 -
57 -If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
58 -
59 -[[image:1713513732175-702.png||height="354" width="836"]]
10 +2.