Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 26.1
edited by Karry Zhuang
on 2024/04/19 16:19
Change comment: There is no comment for this version
To version 38.1
edited by Karry Zhuang
on 2024/04/26 15:04
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,15 +1,30 @@
1 +
2 +
3 +
4 +**Table of Contents:**
5 +
6 +{{toc/}}
7 +
8 +
9 +
10 +
11 +
12 +
13 +
1 1  = 1. Prepare Hardware & Software =
2 2  
3 -* Update Tool:
16 +* Update Tool:[[OTA_Tool>>https://www.dropbox.com/scl/fi/d0tephd9ttghwf1ednj2s/OTA_Tool.rar?rlkey=sll5ny1fikqc8l0se9c4egxzs&st=f3ml8mop&dl=0]]
4 4  * Hardware: Sensor, Converter
5 -* Firmware:
18 +* Firmware:[[Digital wheel dial firmware>>https://www.dropbox.com/scl/fi/nxa0nw0k2qhbpcxzfsz03/Digital-table-wheel-firmware.rar?rlkey=u9wqmilfwu899fhc9i2jfcwou&st=ftsl46f5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=5m196s89&dl=0]]
6 6  
7 7  = 2. Hardware Connection =
8 8  
9 -The data cable should be connected to the AIS (note: there is no camera on this side), while the computer should be connected on the other side.
22 +The AI Sensors and UART are connected and then connected to the PC.
10 10  
11 -[[image:image-20240419145552-1.jpeg||height="399" width="476"]] [[image:image-20240419145552-2.jpeg||height="395" width="395"]]
24 +[[image:image-20240424145937-3.png||height="629" width="544"]]
12 12  
26 +[[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
27 +
13 13  = 3.OTA UART flash =
14 14  
15 15  Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
... ... @@ -26,36 +26,33 @@
26 26  
27 27  2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
28 28  
29 -3 Select a port number. For example, the serial port number is COM17. Press 1 to select COM17
44 +3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17
30 30  
31 31  4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
32 32  
33 -[[image:1713511914316-181.png||height="664" width="761"]]
48 +[[image:1713511914316-181.png||height="754" width="865"]]
34 34  After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
35 35  
36 -[[image:1713513351848-254.png||height="428" width="773"]]x
51 +[[image:1713513351848-254.png||height="477" width="861"]]x
37 37  
38 38  Select 1 to check whether the configured port is correct.
39 39  
40 -[[image:1713513373484-487.png]]
55 +[[image:1713513373484-487.png||height="472" width="856"]]
41 41  
42 42  Select 2 is port is after normal communication with AIS.
43 43  
44 -[[image:1713513478607-793.png||height="428" width="773"]]
59 +[[image:1713513478607-793.png||height="471" width="851"]]
45 45  
46 46  Press 0, press Enter, and select 2 to go to the upgrade surface.
47 47  
48 -[[image:1713513522820-547.png||height="426" width="773"]]
63 +[[image:1713513522820-547.png||height="467" width="847"]]
49 49  
50 -[[image:1713513544122-175.png||height="426" width="771"]]
65 +[[image:1713513544122-175.png||height="467" width="845"]]
51 51  
52 52  Select 2 to enter the upgrade.
53 53  
54 -[[image:1713513668777-698.png||height="429" width="776"]]
69 +[[image:1713513668777-698.png||height="464" width="840"]]
55 55  
56 56  If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
57 57  
58 -[[image:1713513732175-702.png||height="327" width="772"]]
59 -
60 -
61 -
73 +[[image:1713513732175-702.png||height="354" width="836"]]
image-20240424145824-1.gif
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 MB
Content
image-20240424145847-2.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +3.1 MB
Content
image-20240424145937-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +2.2 MB
Content
layout.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +192 bytes
Content