Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 24.1
edited by Karry Zhuang
on 2024/04/19 16:02
Change comment: Uploaded new attachment "1713513732175-702.png", version {1}
To version 43.4
edited by Xiaoling
on 2024/05/17 10:54
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.karry
1 +XWiki.Xiaoling
Content
... ... @@ -1,10 +1,84 @@
1 -~1. Prepare Hardware & Software
1 +
2 2  
3 -* Update Tool
4 -* Hardware: Sensor, Converter
5 -* Firmware:
6 6  
4 +**Table of Contents:**
7 7  
8 -~1. Hardware Connection
6 +{{toc/}}
9 9  
10 -2.
8 +
9 +
10 +
11 +
12 +
13 +
14 += 1. Prepare Hardware & Software =
15 +
16 +
17 +* Update Tool: [[OTA_Tool>>https://www.dropbox.com/scl/fi/d0tephd9ttghwf1ednj2s/OTA_Tool.rar?rlkey=sll5ny1fikqc8l0se9c4egxzs&st=f3ml8mop&dl=0]]
18 +* Hardware: AIS Sensor, AUC USB TTL Adapter for AIS Sensors, PC
19 +* Firmware: [[Digital wheel dial firmware>>https://www.dropbox.com/scl/fi/nxa0nw0k2qhbpcxzfsz03/Digital-table-wheel-firmware.rar?rlkey=u9wqmilfwu899fhc9i2jfcwou&st=ftsl46f5&dl=0]]，[[Pointer dial firmware>>https://www.dropbox.com/scl/fi/y03feisk7ztq1ey6pmhqb/Pointer-dial-firmware.rar?rlkey=knlx67m1g26xukrthcum1kk23&st=5m196s89&dl=0]]
20 +
21 +
22 += 2. Hardware Connection =
23 +
24 +
25 +The AIS Sensors and AUC USB TTL Adapter for AIS Sensors are connected and then connected to the PC.
26 +
27 +[[image:image-20240428155042-1.png||height="598" width="506"]]
28 +
29 +[[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
30 +
31 +
32 += 3.OTA UART flash =
33 +
34 +
35 +Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
36 +
37 +[[image:1713510920220-760.png||height="219" width="816"]]
38 +
39 +The OTA_Tool folder should be opened and the program can be run by double-clicking on ota.exe.
40 +
41 +[[image:1713511385474-910.png||height="452" width="804"]]
42 +
43 +When the program opens, follow these steps.
44 +
45 +1 Select the chip type. AIS uses QFN72. Press 2 to select QFN72
46 +
47 +2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
48 +
49 +3 Select a port number.The instance device port number is 17.Press 1 to select COM17
50 +
51 +4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
52 +
53 +[[image:1713511914316-181.png||height="754" width="865"]]
54 +
55 +
56 +After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
57 +
58 +[[image:1713513351848-254.png||height="477" width="861"]]x
59 +
60 +
61 +Select 1 to check whether the configured port is correct.
62 +
63 +[[image:1713513373484-487.png||height="472" width="856"]]
64 +
65 +
66 +Select 2 is port is after normal communication with AIS.
67 +
68 +[[image:1713513478607-793.png||height="471" width="851"]]
69 +
70 +
71 +Press 0, press Enter, and select 2 to go to the upgrade surface.
72 +
73 +[[image:1713513522820-547.png||height="467" width="847"]]
74 +
75 +[[image:1713513544122-175.png||height="467" width="845"]]
76 +
77 +
78 +Select 2 to enter the upgrade.
79 +
80 +[[image:1713513668777-698.png||height="464" width="840"]]
81 +
82 +If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
83 +
84 +[[image:1713513732175-702.png||height="354" width="836"]]
image-20240424145824-1.gif
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 MB
Content
image-20240424145847-2.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +3.1 MB
Content
image-20240424145937-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +2.2 MB
Content
image-20240428155042-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +3.1 MB
Content
layout.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +192 bytes
Content