Skip to Content
Last modified by Karry Zhuang on 2024/09/20 17:17
From version 21.1
edited by Karry Zhuang
on 2024/04/19 15:59
Change comment: Uploaded new attachment "1713513562444-394.png", version {1}
To version 34.3
edited by Karry Zhuang
on 2024/04/24 17:19
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,10 +1,60 @@
1 -~1. Prepare Hardware & Software
1 += 1. Prepare Hardware & Software =
2 2  
3 -* Update Tool
3 +* Update Tool:OTA_Tool
4 4  * Hardware: Sensor, Converter
5 5  * Firmware:
6 6  
7 += 2. Hardware Connection =
7 7  
8 -~1. Hardware Connection
9 +The AI Sensors and UART are connected and then connected to the PC.
9 9  
10 -2.
11 +[[image:image-20240424145937-3.png||height="629" width="544"]]
12 +
13 +[[image:image-20240424145824-1.gif]][[image:image-20240424145847-2.jpeg||height="359" width="478"]]
14 +
15 += 3.OTA UART flash =
16 +
17 +Open the OTA_Tool folder and put the latest firmware "layout.bin" and "output. img" into the img folder.
18 +
19 +[[image:1713510920220-760.png||height="219" width="816"]]
20 +
21 +The OTA_Tool folder should be opened and the program can be run by double-clicking on ota.exe.
22 +
23 +[[image:1713511385474-910.png||height="452" width="804"]]
24 +
25 +When the program opens, follow these steps.
26 +
27 +1 Select the chip type. AIS uses QFN72. Press 2 to select QFN72
28 +
29 +2 Select an upgrade mode. AIS supports serial port upgrade only. Press 2 to select Uart protocol
30 +
31 +3 Select a port number. Choose the largest number of serial port, For example, here shows 16 and 17. Press 1 to select COM17
32 +
33 +4 Select the baud rate. The default baud rate is 921600. Press 14 to select 921600
34 +
35 +[[image:1713511914316-181.png||height="754" width="865"]]
36 +After the baud rate is configured, the upgrade page is displayed. 1 is to check whether the communication port is correct.
37 +
38 +[[image:1713513351848-254.png||height="477" width="861"]]x
39 +
40 +Select 1 to check whether the configured port is correct.
41 +
42 +[[image:1713513373484-487.png||height="472" width="856"]]
43 +
44 +Select 2 is port is after normal communication with AIS.
45 +
46 +[[image:1713513478607-793.png||height="471" width="851"]]
47 +
48 +Press 0, press Enter, and select 2 to go to the upgrade surface.
49 +
50 +[[image:1713513522820-547.png||height="467" width="847"]]
51 +
52 +[[image:1713513544122-175.png||height="467" width="845"]]
53 +
54 +Select 2 to enter the upgrade.
55 +
56 +[[image:1713513668777-698.png||height="464" width="840"]]
57 +
58 +If ReBoot WEI is displayed as shown in the following figure, the upgrade succeeds.
59 +
60 +[[image:1713513732175-702.png||height="354" width="836"]]
1713513668777-698.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +45.5 KB
Content
1713513718489-217.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +29.1 KB
Content
1713513732175-702.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +41.9 KB
Content
image-20240424145824-1.gif
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 MB
Content
image-20240424145847-2.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +3.1 MB
Content
image-20240424145937-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +2.2 MB
Content
layout.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.karry
Size
... ... @@ -1,0 +1,1 @@
1 +192 bytes
Content