Wiki source code of UART Access for LoRa ST v4 base model
Version 16.1 by Bei Jinggeng on 2023/03/20 10:25
Show last authors
| author | version | line-number | content |
|---|---|---|---|
| 1 | **Table of Contents:** | ||
| 2 | |||
| 3 | {{toc/}} | ||
| 4 | |||
| 5 | |||
| 6 | |||
| 7 | |||
| 8 | |||
| 9 | = 1. LoRaST v4 base Hardware = | ||
| 10 | |||
| 11 | |||
| 12 | Below hardware use LoRaST v4 module. They module support UART Access for AT Command and Firmware Upgrade. | ||
| 13 | {{velocity}}$xwiki.ssfx.use("js/xwiki/table/table.css") | ||
| 14 | $xwiki.jsfx.use("js/xwiki/table/tablefilterNsort.js", true){{/velocity}} | ||
| 15 | |||
| 16 | (% border="1" cellspacing="10" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f7faff; width:621.989px" %) | ||
| 17 | (% class="sortHeader" %)|=(% style="width: 77px;" %)Model|=(% style="width: 120px;" %)Mother Board|=(% style="width: 199px;" %)UART for AT Commands|=(% style="width: 221px;" %)UART for Upgrade Firmware | ||
| 18 | |(% style="width:77px" %)((( | ||
| 19 | **PS-LB ** | ||
| 20 | )))|(% style="width:120px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:221px" %)Instruction | ||
| 21 | |||
| 22 | |||
| 23 | = 2. UART for AT Commands = | ||
| 24 | |||
| 25 | == 2.1 Generate software set up for AT Commands via UART == | ||
| 26 | |||
| 27 | |||
| 28 | (% start="1" style="list-style-type:none" %) | ||
| 29 | 1. Use a general serial tool. | ||
| 30 | 1. Connect PC to device's UART interface | ||
| 31 | 1. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control. | ||
| 32 | 1. ((( | ||
| 33 | The password is the last six characters of APPSKEY | ||
| 34 | |||
| 35 | Example： | ||
| 36 | |||
| 37 | APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85 | ||
| 38 | |||
| 39 | The password：147485 | ||
| 40 | ))) | ||
| 41 | |||
| 42 | [[image:image-20221224170218-1.png||height="497" width="640"]] | ||
| 43 | |||
| 44 | |||
| 45 | == 2.2 UART Connection for SIB mother board == | ||
| 46 | |||
| 47 | |||
| 48 | [[image:image-20221224171304-3.png||height="545" width="863"]] | ||
| 49 | |||
| 50 | |||
| 51 | = 3. UART for Firmware Upgrade = | ||
| 52 | |||
| 53 | == 3.1 General Instruction for UART update firmware == | ||
| 54 | |||
| 55 | |||
| 56 | LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps: | ||
| 57 | |||
| 58 | (% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially. | ||
| 59 | |||
| 60 | (% style="color:blue" %)**Step2**(%%): Press (% style="color:blue" %)**Reset**(%%) button, the module will then boot into program mode. | ||
| 61 | |||
| 62 | (% style="color:blue" %)**Step3**(%%): Use (% style="color:blue" %)**TremoProgrammer**(%%) to update the firmware to LoRaST v4. | ||
| 63 | |||
| 64 | (% style="color:blue" %)**Step4**(%%): Set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) position. Press Reset button again and module will run the new software. | ||
| 65 | |||
| 66 | |||
| 67 | Below is the method for how to update via (% style="color:blue" %)**TremoProgrammer:** | ||
| 68 | |||
| 69 | 1. Software download link: [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]] | ||
| 70 | |||
| 71 | 2. Run** (% style="color:blue" %)TremoProgrammer.(%%)** | ||
| 72 | |||
| 73 | 3. Choose software and set the address to (% style="color:blue" %)**0x0800D000** | ||
| 74 | |||
| 75 | 4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update | ||
| 76 | |||
| 77 | [[image:image-20221224174341-4.png||height="471" width="374"]] | ||
| 78 | |||
| 79 | |||
| 80 | == 3.2 UART Connection for SIB mother board for Program. == | ||
| 81 | |||
| 82 | |||
| 83 | Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference. | ||
| 84 | |||
| 85 | [[image:image-20221224174605-6.png||height="569" width="880"]] | ||
| 86 | |||
| 87 | |||
| 88 |