Last modified by Mengting Qiu on 2024/11/11 17:09
<
From version < 33.1 >
edited by Edwin Chen
on 2023/05/15 10:30
To version < 14.1 >
edited by Edwin Chen
on 2022/12/24 17:47
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,5 @@
1 -(% class="wikigeneratedid" %)
1 +
2 +
2 2  **Table of Contents:**
3 3  
4 4  {{toc/}}
... ... @@ -6,125 +6,67 @@
6 6  
7 7  
8 8  
9 -= 1. LoRaST v4 base Hardware =
10 10  
11 += LoRaST v4 base Hardware =
11 11  
12 -Below hardware use LoRaST v4 module. They supports UART Access for AT Command and Firmware Upgrade.
13 +Below hardware use LoRaST v4 module. They module support UART Access for AT Command and Firmware Upgrade.
13 13  
14 -{{velocity}}
15 -$xwiki.ssfx.use("js/xwiki/table/table.css")
16 -$xwiki.jsfx.use("js/xwiki/table/tablefilterNsort.js", true)
17 -{{/velocity}}
15 +(% border="1" cellspacing="10" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f7faff; width:770px" %)
16 +(% class="sortHeader" %)|=(% style="width: 180px;" %)Model|=(% style="width: 135px;" %)Mother Board|=(% style="width: 199px;" %)UART for AT Commands|=(% style="width: 230px;" %)UART for Upgrade Firmware
17 +|(% style="width:180px" %)(((
18 +**PS-LB **
19 +)))|(% style="width:135px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:230px" %)Instruction
18 18  
19 -(% border="1" cellspacing="5" class="doOddEven filterable grid sortable" id="tableid" style="width:829px" %)
20 -|(% style="background-color:#d9e2f3; width:290px" %)**Models**|(% style="background-color:#d9e2f3; color:#0070c0; width:172px" %)**Mother Board**|(% style="background-color:#d9e2f3; color:#0070c0; width:116px" %)**UART for AT Commands**|(% style="background-color:#d9e2f3; color:#0070c0; width:248px" %)**UART for Upgrade Firmware**
21 -|(% style="width:290px" %)PS-LB, PS-LB-NA, SDI12-LB|(% style="width:172px" %)SIB|(% style="width:116px" %)Instruction|(% style="width:248px" %)Instruction
22 -|(% style="width:290px" %)(((
23 -SN50v3, S31-LB, S31B-LB,
21 += UART for AT Commands =
24 24  
25 -D20-LB.D20S-LB, D21-LB, D22-LB
26 -)))|(% style="width:172px" %)SN50v3|(% style="width:116px" %) |(% style="width:248px" %)
27 -|(% style="width:290px" %)LHT65N|(% style="width:172px" %)LHT65N|(% style="width:116px" %) |(% style="width:248px" %)
28 -|(% style="width:290px" %) |(% style="width:172px" %) |(% style="width:116px" %) |(% style="width:248px" %)
23 +== Generate software set up for AT Commands via UART ==
29 29  
30 -= 2. UART for AT Commands =
25 +1. Use a general serial tool.
26 +1. Connect PC to device's UART interface
27 +1. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
31 31  
32 -== 2.1 Generate software set up for AT Commands via UART ==
33 -
34 -
35 -~1. Use a general serial tool.
36 -
37 -2. Connect PC to device's UART interface
38 -
39 -3. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
40 -
41 -(((
42 -4. The password is the last six characters of APPSKEY or PIN of box
43 -
44 -**Example：**
45 -
46 -APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85
47 -
48 -The password：147485
49 -
50 -[[image:image-20230329162900-1.png||height="302" width="648"]]
51 -
52 -
53 -)))
54 -
55 55  [[image:image-20221224170218-1.png||height="497" width="640"]]
56 56  
57 57  
58 -== 2.2 UART Connection for SIB mother board ==
32 +== UART Connection for SIB mother board ==
59 59  
60 -
61 61  [[image:image-20221224171304-3.png||height="545" width="863"]]
62 62  
63 63  
64 -== 2.3 UART Connection for SN50v3 base mother board ==
65 65  
38 += UART for Firmware Upgrade =
66 66  
40 +== General Instruction for UART update firmware ==
67 67  
68 -= 3. UART for Firmware Upgrade =
42 +LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
69 69  
70 -== 3.1 Check Your device already have bootloader ==
44 + **Step1**: Set BOOT Switch to **PROG** mode. PROG mode is for update firmware specially.
71 71  
72 -=== 3.1.1 What is Dragino Bootloader? ===
46 + **Step2**: Press **Reset** button, the module will then boot into program mode.
73 73  
48 + **Step3**: Use **TremoProgrammer** to update the firmware to LoRaST v4.
74 74  
75 -Dragino Bootloader is a customizer made bootloader which support below features:
50 + **Step4**: Set BOOT Switch to **FLASH** position. Press Reset button again and module will run the new software.
76 76  
77 -* OTA Update via LoRa or BLE
78 -* OTA Batch update configure via LoRa or BLE
79 79  
80 -All Dragino End Devices base on LoRa ST v4 supports Dragino Bootloader.
53 +Below is the method for how to update via **TremoProgrammer:**
81 81  
55 +1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
82 82  
83 -=== 3.1.2 How can i know if my device already have bootloader? ===
57 +2.  Run** TremoProgrammer.**
84 84  
85 -If a device has a bootloader. it will output bootloader info to UART when boot. As below:
59 +3.  Choose software and set the address to **0x0800D000**
86 86  
87 -[[image:image-20230514150410-1.png||height="398" width="815"]]
61 +4. Rember to set BOOT Switch to FLASH after update
88 88  
63 +[[image:image-20221224174341-4.png||height="471" width="374"]]
89 89  
90 -=== 3.1.3 How to upload bootloader to device? ===
91 91  
92 -If your is LoRa ST v4 base hardware and doesn't have bootloader. You can upload a bootloader to it.
66 +== UART Connection for SIB mother board for Program. ==
93 93  
68 +Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference.
94 94  
95 -== 3.2 Update Firmware (Assume the device already have a bootloader) ==
70 +[[image:image-20221224174605-6.png||height="569" width="880"]]
96 96  
97 -=== 3.2.1 Update a firmware via Dragino bootloader ===
98 98  
99 -
100 -
101 -
102 -=== 3.2.2 Update a firmware via TremoProgrammer ===
103 -
104 -Make sure your device already bootloader while use this update. Other device won't be able to boot ( can be solve by upload a bootloader to the device).
105 -
106 -LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
107 -
108 - (% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
109 -
110 - (% style="color:blue" %)**Step2**(%%): Press (% style="color:blue" %)**Reset**(%%) button, the module will then boot into program mode.
111 -
112 - (% style="color:blue" %)**Step3**(%%): Use (% style="color:blue" %)**TremoProgrammer**(%%) to update the firmware to LoRaST v4.
113 -
114 - (% style="color:blue" %)**Step4**(%%): Set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) position. Press Reset button again and module will run the new software.
115 -
116 -
117 -Below is the method for how to update via (% style="color:blue" %)**TremoProgrammer:**
118 -
119 -1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
120 -
121 -2.  Run** (% style="color:blue" %)TremoProgrammer.(%%)**
122 -
123 -3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000**(%%). (% style="color:red" %)VERY IMPORTANT: USE THIS ADDRESS FOR FIRMWARE WITHOUT BOOTLOADER
124 -
125 -4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update
126 -
127 -[[image:image-20221224174341-4.png||height="471" width="374"]]
128 -
129 -
130 130  
image-20230329162900-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -217.0 KB
Content
image-20230514150410-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -275.3 KB
Content
image-20230515102801-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -812.6 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0