Summary

• Page properties (2 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • image-20230329162900-1.png

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.Xiaoling
	1	+XWiki.Edwin

Content

...	...	@@ -16,20 +16,32 @@
16	16	(% border="1" cellspacing="10" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f7faff; width:621.989px" %)
17	17	(% class="sortHeader" %)|=(% style="width: 77px;" %)Model|=(% style="width: 120px;" %)Mother Board|=(% style="width: 199px;" %)UART for AT Commands|=(% style="width: 221px;" %)UART for Upgrade Firmware
18	18	|(% style="width:77px" %)(((
19		-**PS-LB **
	19	+PS-LB
20	20	)))|(% style="width:120px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:221px" %)Instruction
21	21
22		-
23		-
24	24	= 2. UART for AT Commands =
25	25
26	26	== 2.1 Generate software set up for AT Commands via UART ==
27	27
28	28
	27	+(% start="1" style="list-style-type:decimal" %)
29	29	1. Use a general serial tool.
30	30	1. Connect PC to device's UART interface
31	31	1. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
	31	+1. (((
	32	+The password is the last six characters of APPSKEY or PIN of box
32	32
	34	+**Example：**
	35	+
	36	+APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85
	37	+
	38	+The password：147485
	39	+
	40	+[[image:image-20230329162900-1.png||height="302" width="648"]]
	41	+
	42	+
	43	+)))
	44	+
33	33	[[image:image-20221224170218-1.png||height="497" width="640"]]
34	34
35	35
...	...	@@ -39,11 +39,16 @@
39	39	[[image:image-20221224171304-3.png||height="545" width="863"]]
40	40
41	41
	54	+== 2.3 UART Connection for SN50v3 base mother board ==
	55	+
	56	+
42	42	= 3. UART for Firmware Upgrade =
43	43
44		-== 3.1 General Instruction for UART update firmware ==
	59	+== 3.1 Update firmware ==
45	45
	61	+=== 3.1.1 Update a firmware without bootloader ===
46	46
	63	+
47	47	LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
48	48
49	49	(% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
...	...	@@ -61,7 +61,7 @@
61	61
62	62	2.  Run** (% style="color:blue" %)TremoProgrammer.(%%)**
63	63
64		-3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000**
	81	+3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000(%%)**. (% style="color:red" %)VERY IMPORTANT: USE THIS ADDRESS FOR FIRMWARE WITHOUT BOOTLOADER(%%)
65	65
66	66	4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update
67	67

image-20230329162900-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Bei

Size

...	...	@@ -1,0 +1,1 @@
	1	+217.0 KB

Content