Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 2 removed)
  • image-20221224174529-5.png
  • image-20221224174605-6.png

Details

Page properties

Content

...	...	@@ -1,13 +11,3 @@
1		-
2		-
3		-**Table of Contents:**
4		-
5		-{{toc/}}
6		-
7		-
8		-
9		-
10		-
11	11	= LoRaST v4 base Hardware =
12	12
13	13	Below hardware use LoRaST v4 module. They module support UART Access for AT Command and Firmware Upgrade.
...	...	@@ -18,6 +18,7 @@
18	18	**PS-LB **
19	19	)))|(% style="width:135px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:230px" %)Instruction
20	20
	11	+
21	21	= UART for AT Commands =
22	22
23	23	== Generate software set up for AT Commands via UART ==
...	...	@@ -37,37 +37,4 @@
37	37
38	38	= UART for Firmware Upgrade =
39	39
40		-== General Instruction for UART update firmware ==
41		-
42		-LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
43		-
44		- **Step1**: Set BOOT Switch to **PROG** mode. PROG mode is for update firmware specially.
45		-
46		- **Step2**: Press **Reset** button, the module will then boot into program mode.
47		-
48		- **Step3**: Use **TremoProgrammer** to update the firmware to LoRaST v4.
49		-
50		- **Step4**: Set BOOT Switch to **FLASH** position. Press Reset button again and module will run the new software.
51		-
52		-
53		-Below is the method for how to update via **TremoProgrammer:**
54		-
55		-1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
56		-
57		-2.  Run** TremoProgrammer.**
58		-
59		-3.  Choose software and set the address to **0x0800D000**
60		-
61		-4. Rember to set BOOT Switch to FLASH after update
62		-
63		-[[image:image-20221224174341-4.png||height="471" width="374"]]
64		-
65		-
66		-== UART Connection for SIB mother board for Program. ==
67		-
68		-Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference.
69		-
70		-[[image:image-20221224174605-6.png||height="569" width="880"]]
71		-
72		-
73	73

image-20221224174529-5.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Edwin

Size

...	...	@@ -1,1 +1,0 @@
1		-1.6 MB

Content

image-20221224174605-6.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Edwin

Size

...	...	@@ -1,1 +1,0 @@
1		-1.5 MB

Content