Last modified by Mengting Qiu on 2024/11/11 17:09
<
From version < 13.1 >
edited by Edwin Chen
on 2022/12/24 17:47
To version < 26.17 >
edited by Xiaoling
on 2023/04/20 11:06
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Xiaoling
Content
... ... @@ -1,63 +1,120 @@
1 -= LoRaST v4 base Hardware =
1 +(% class="wikigeneratedid" %)
2 +**Table of Contents:**
2 2  
4 +{{toc/}}
5 +
6 +
7 +
8 +
9 += 1. LoRaST v4 base Hardware =
10 +
11 +
3 3  Below hardware use LoRaST v4 module. They module support UART Access for AT Command and Firmware Upgrade.
4 4  
5 -(% border="1" cellspacing="10" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f7faff; width:770px" %)
6 -(% class="sortHeader" %)|=(% style="width: 180px;" %)Model|=(% style="width: 135px;" %)Mother Board|=(% style="width: 199px;" %)UART for AT Commands|=(% style="width: 230px;" %)UART for Upgrade Firmware
7 -|(% style="width:180px" %)(((
8 -**PS-LB **
9 -)))|(% style="width:135px" %)SIB|(% style="width:199px" %)Instruction|(% style="width:230px" %)Instruction
14 +(% style="display:none" %)
10 10  
11 -= UART for AT Commands =
12 12  
13 -== Generate software set up for AT Commands via UART ==
14 14  
18 +
19 += 2. UART for AT Commands =
20 +
21 +== 2.1 Generate software set up for AT Commands via UART ==
22 +
23 +
24 +(% start="1" style="list-style-type:decimal" %)
15 15  1. Use a general serial tool.
16 16  1. Connect PC to device's UART interface
17 17  1. Set up serial tool with : BaudRate: 9600, databit:8, No parity, No flow control.
28 +1. (((
29 +The password is the last six characters of APPSKEY or PIN of box
18 18  
31 +**Example：**
32 +
33 +APPSKEY= 41 85 71 A7 5D 7E 54 52 25 58 74 85 96 14 74 85
34 +
35 +The password：147485
36 +
37 +[[image:image-20230329162900-1.png||height="302" width="648"]]
38 +
39 +
40 +)))
41 +
19 19  [[image:image-20221224170218-1.png||height="497" width="640"]]
20 20  
21 21  
22 -== UART Connection for SIB mother board ==
45 +== 2.2 UART Connection for SIB mother board ==
23 23  
47 +
24 24  [[image:image-20221224171304-3.png||height="545" width="863"]]
25 25  
26 26  
51 +== 2.3 UART Connection for SN50v3 base mother board ==
27 27  
28 -= UART for Firmware Upgrade =
29 29  
30 -== General Instruction for UART update firmware ==
54 += 3. UART for Firmware Upgrade =
31 31  
56 +== 3.1 Update firmware ==
57 +
58 +=== 3.1.0 What is Dragino Bootloader? ===
59 +
60 +Dragino Bootloader is a customizer made bootloader which support below features:
61 +
62 +* OTA Update via LoRa or BLE
63 +* OTA Batch update configure via LoRa or BLE
64 +
65 +{{velocity}}
66 +$xwiki.ssfx.use("js/xwiki/table/table.css")
67 +$xwiki.jsfx.use("js/xwiki/table/tablefilterNsort.js", true)
68 +{{/velocity}}
69 +
70 +(% border="1" cellspacing="10" class="doOddEven filterable grid sortable" id="tableid" style="background-color:#f7faff; width:621.989px" %)
71 +(% class="sortHeader" %)|=(% style="width: 307px;" %)Model with LoRa Bootloader|=(% style="width: 313px;" %)Model with BLE Bootloader
72 +|(% style="width:307px" %)(((
73 +PS-LB, SDI12-LB, PS-LB-NA, SN50v3-LB,
74 +
75 +D2x-LB, S31x-LB, SDI12-LB
76 +)))|(% style="width:313px" %)
77 +
78 +=== 3.1.1 Update a firmware with Dragino bootloader ===
79 +
80 +
81 +
82 +
83 +=== 3.1.2 Update a firmware without bootloader ===
84 +
85 +If a firmware's name doesn't have the suffix **_with_bootloader**. It means the firmware is without bootloader and user can use this method to uplink.
86 +
32 32  LoRaSTv4 Base hardware support UART update firmware. the UART connection is the same as AT Command connection, with the need for two extra action. See below for the steps:
33 33  
34 - **Step1**: Set BOOT Switch to **PROG** mode. PROG mode is for update firmware specially.
89 + (% style="color:blue" %)**Step1**(%%): Set BOOT Switch to (% style="color:blue" %)**PROG**(%%) mode. PROG mode is for update firmware specially.
35 35  
36 - **Step2**: Press **Reset** button, the module will then boot into program mode.
91 + (% style="color:blue" %)**Step2**(%%): Press (% style="color:blue" %)**Reset**(%%) button, the module will then boot into program mode.
37 37  
38 - **Step3**: Use **TremoProgrammer** to update the firmware to LoRaST v4.
93 + (% style="color:blue" %)**Step3**(%%): Use (% style="color:blue" %)**TremoProgrammer**(%%) to update the firmware to LoRaST v4.
39 39  
40 - **Step4**: Set BOOT Switch to **FLASH** position. Press Reset button again and module will run the new software.
95 + (% style="color:blue" %)**Step4**(%%): Set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) position. Press Reset button again and module will run the new software.
41 41  
42 42  
43 -Below is the method for how to update via **TremoProgrammer:**
98 +Below is the method for how to update via (% style="color:blue" %)**TremoProgrammer:**
44 44  
45 45  1.  Software download link:  [[https:~~/~~/www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0>>url:https://www.dropbox.com/sh/j0qyc7a9ejit7jk/AACtx2tK4gEv6YFXMIVUM4dLa?dl=0]]
46 46  
47 -2.  Run** TremoProgrammer.**
102 +2.  Run** (% style="color:blue" %)TremoProgrammer.(%%)**
48 48  
49 -3.  Choose software and set the address to **0x0800D000**
104 +3.  Choose software and set the address to (% style="color:blue" %)**0x0800D000**(%%). (% style="color:red" %)VERY IMPORTANT: USE THIS ADDRESS FOR FIRMWARE WITHOUT BOOTLOADER
50 50  
51 -4. Rember to set BOOT Switch to FLASH after update
106 +4. Rember to set BOOT Switch to (% style="color:blue" %)**FLASH**(%%) after update
52 52  
53 53  [[image:image-20221224174341-4.png||height="471" width="374"]]
54 54  
55 55  
56 -== UART Connection for SIB mother board for Program. ==
57 57  
58 -Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference.
59 59  
60 -[[image:image-20221224174605-6.png||height="569" width="880"]]
61 61  
62 62  
63 -
115 +== 3.2 UART Connection for SIB mother board for Program. ==
116 +
117 +
118 +Below shows the SIB board UART connection, reset button and BOOT Switch (Program Jumper) position. They can be used for firmware upgrade reference.
119 +
120 +[[image:image-20221224174605-6.png||height="569" width="880"]]
image-20230329162900-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Bei
Size
... ... @@ -1,0 +1,1 @@
1 +217.0 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0