Changes for page Notes for ChirpStack

Last modified by Kilight Cao on 2024/09/24 15:23
<
From version < 211.1 >
edited by Kilight Cao
on 2024/02/03 14:38
To version < 108.10 >
edited by Xiaoling
on 2022/07/23 14:22
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Kilight
1 +XWiki.Xiaoling
Content
... ... @@ -20,7 +20,7 @@
20 20  
21 21  **1) Have a Chirstack Server.**
22 22  
23 -[[image:image-20230821114047-4.png||height="524" width="990"]]
23 +[[image:image-20220525100058-1.png]]
24 24  
25 25  ChirpStack home page
26 26  
... ... @@ -38,58 +38,12 @@
38 38  )))
39 39  
40 40  
41 -= 2.  Node usage introduction =
42 42  
43 -== 2.1 Register Node ==
42 += 2.  Semtech UDP =
44 44  
44 +== 2.1  Step 1. Add the Network-servers ==
45 45  
46 -**Step 1: Add application**
47 47  
48 -[[image:image-20230702094608-1.png||height="537" width="1015"]]
49 -
50 -
51 -**Step 2：Fill name**
52 -
53 -[[image:image-20230702094852-2.png]]
54 -
55 -
56 -**Step3 ：Add device profile**
57 -
58 -[[image:image-20230702095114-4.png||height="448" width="1061"]]
59 -
60 -
61 -**Step4 ：Configure your device profile**
62 -
63 -[[image:image-20230702095557-5.png||height="648" width="1121"]]
64 -
65 -Does node support class-c
66 -
67 -[[image:image-20230702095641-6.png||height="349" width="1114"]]
68 -
69 -Add node's decoder
70 -
71 -[[image:image-20230702095827-7.png||height="490" width="1138"]]
72 -
73 -
74 -**Step5 ：add device**
75 -
76 -[[image:image-20230702094944-3.png||height="439" width="1153"]]
77 -
78 -
79 -[[image:image-20230702100312-8.png||height="550" width="1106"]]
80 -
81 -
82 -[[image:image-20230702100543-10.png||height="313" width="1099"]]
83 -
84 -
85 -[[image:image-20230702100930-11.png||height="613" width="1098"]]
86 -
87 -
88 -= 3.  Semtech UDP for ChirpStack v3 =
89 -
90 -== 3.1  Step 1. Add the Network-servers ==
91 -
92 -
93 93  The network-Servers address varies depending on the ChirpStack server setup environment
94 94  
95 95  (% class="box" %)
... ... @@ -101,24 +101,27 @@
101 101  
102 102  (% style="color:red" %)**If the user cannot add network-Servers, re-check the ChirpStack code or the server building process.**
103 103  
104 -[[image:image-20220531171609-1.png||height="638" width="1268"]](% style="display:none" %)
105 105  
59 +[[image:image-20220531171609-1.png]]
60 +
106 106  Add the Network-servers
107 107  
108 108  
109 -== 3.2  Step 2. Create Gateway-profiles ==
110 110  
65 +== 2.2  Step 2. Create Gateway-profiles ==
111 111  
112 -[[image:image-20220531171651-2.png||height="632" width="1264"]](% style="display:none" %)
113 113  
68 +[[image:image-20220531171651-2.png]]
69 +
114 114  Create Gateway-profiles
115 115  
116 116  
117 -== 3.3  Step 3. Create Service-profiles ==
118 118  
74 +== 2.3  Step 3. Create Service-profiles ==
119 119  
120 -[[image:image-20220531171809-3.png||height="761" width="1265"]]
121 121  
77 +[[image:image-20220531171809-3.png]]
78 +
122 122  Create Service-profiles
123 123  
124 124  
... ... @@ -129,59 +129,51 @@
129 129  If the user has completed the preceding steps, proceed to the next step.(% style="display:none" %)
130 130  
131 131  
132 -== 3.4  Step 4. Add the gateway ==
133 133  
90 +== 2.4  Step 4. Add the gateway ==
134 134  
92 +
135 135  The example gateway id is: a840411e96744150
136 136  
137 137  (((
138 138  (% style="color:red" %)**Note : The Gateway EUI and server addresses must match the ChirpStack configuration.**
97 +
98 +
139 139  )))
140 140  
141 -[[image:image-20220531171923-4.png||height="745" width="1253"]](% style="display:none" %)
101 +[[image:image-20220531171923-4.png]](% style="display:none" %)
142 142  
143 143  Add the gateway
144 144  
145 145  
106 +
146 146  [[image:image-20220531172031-5.png]]
147 147  
148 148  Configure the gateway
149 149  
150 150  
151 -== 3.5  Step 5. Checking gateway Status ==
152 152  
113 +== 2.5  Step 5. Checking gateway Status ==
153 153  
154 -[[image:image-20220531172158-6.png||height="704" width="1167"]](% style="display:none" %)
155 155  
116 +[[image:image-20220531172158-6.png]](% style="display:none" %)
156 156  
157 157  
119 +
158 158  gateway Status
159 159  
160 -[[image:image-20220531172304-7.png||height="628" width="1165"]]
122 +[[image:image-20220531172304-7.png]]
161 161  
162 162  gateway Status
163 163  
164 164  
165 -= 4.  Semtech UDP for ChirpStack v4 =
166 166  
167 -== 4.1  Step 1. Add the gateway ==
128 += 3.  Gateway Registration for Basics Station =
168 168  
169 169  
170 -[[image:image-20230926092907-1.png||height="598" width="1007"]]
131 +== 3.1  Introduction ==
171 171  
172 172  
173 -[[image:image-20230926093057-2.png||height="541" width="1002"]]
174 -
175 -
176 -== 4.2  Step 2. Checking gateway Status ==
177 -
178 -[[image:image-20230926093233-3.png||height="581" width="1018"]]
179 -
180 -= 5.  Gateway Registration for Basics Station =
181 -
182 -== 5.1  Introduction ==
183 -
184 -
185 185  The [[Semtech Basic Station>>url:https://doc.sm.tc/station/]] backend implements the [[LNS protocol>>url:https://doc.sm.tc/station/tcproto.html]]. It exposes a WebSocket handler to which Basic Station powered gateways can connect.
186 186  
187 187  ChirpStack Open-Source LoRaWAN® Network Server needs to set up a configuration that can use Semtech BasicStation.
... ... @@ -202,13 +202,14 @@
202 202  A gateway that can access the internet normally
203 203  
204 204  
205 -== 5.2  Add Gateway ==
206 206  
155 +== 3.2  Add Gateway ==
207 207  
157 +
208 208  [[image:image-20220524164205-10.png]]
209 209  
210 210  
211 -== 5.3  Access the gateway GUI ==
161 +== 3.3  Access the gateway GUI ==
212 212  
213 213  
214 214  Access the gateway GUI interface of LoRaWAN~-~->LoRaWAN ~-~- Basic Station
... ... @@ -222,7 +222,7 @@
222 222  (((
223 223  Service Provider  ~-~->  Choose the ChirpStack/Senet ~-~- Basic Station
224 224  
225 -LNS URI  ~-~->  Enter the LNS URI address, For example : wss:~/~/xxxx.chirpstack.com:443 or ws:~/~/xxxx.chirpstack.com:3001
175 +LNS URI  ~-~->  Enter the LNS URI address, For example : wss:~/~/xxxx.chirpstack.com:433 or ws:~/~/xxxx.chirpstack.com:3001
226 226  
227 227  LNS TLS trust  ~-~->  Upload the TLS Certificate
228 228  )))
... ... @@ -231,13 +231,13 @@
231 231  [[image:image-20220524164341-12.png]]
232 232  
233 233  
234 -== 5.4  Start Station ==
184 +== 3.4  Start Station ==
235 235  
236 236  
237 -When the user has finished the configuration, Please click **Sace&Apply** to start station to connect ChirpStack.
187 +When the user has finished the configuration, Please click Sace&Apply to start station to connect ChirpStack
238 238  
239 239  
240 -== 5.5  Successful Connection ==
190 +== 3.5  Successful Connection ==
241 241  
242 242  
243 243  If user completes the above steps, which will see live date in the ChirpStack.
... ... @@ -245,9 +245,10 @@
245 245  [[image:image-20220524164448-13.png]]
246 246  
247 247  
248 -== 5.6  Trouble Shooting ==
249 249  
199 +== 3.6  Trouble Shooting ==
250 250  
201 +
251 251  User can check the station log in the logread/system log page.
252 252  
253 253  [[image:image-20220531172837-8.png]]
... ... @@ -258,247 +258,31 @@
258 258  [[image:image-20220531172857-9.png]]
259 259  
260 260  
261 -= 6.  How the gateway connects to Chirpstack v3 via gateway-bridge =
262 262  
213 += 4. Downlink =
263 263  
264 -(% style="color:blue" %)**Below list the support products and Requirements:**
215 +== 4.1 Chirpstack Downlink Note ==
265 265  
266 -1. LoRaWAN Gateway model: [[LIG16>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/171-lig16.html]], [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]], [[DLOS8>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/160-dlos8.html]] ,[[LPS8>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/148-lps8.html]],[[LPS8N>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/200-lps8n.html]],[[LG308N>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/229-lg308n.html]],[[DLOS8N>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/225-dlos8n.html]]
267 -1. Firmware version since: [[Chirpstack-Bridge-V3.14.6>>https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V3.14.6-Bridge--build-v5.4.1679487778-20230322-2024/]]
268 268  
269 -(% style="color:blue" %)**What do you need to prepare**
218 +[[image:image-20220601102543-2.png]]
270 270  
271 -A gateway that can access the internet normally
220 +Convert the data to Base64
272 272  
273 273  
274 -The following example does not have configuration certificates:
223 +[[image:image-20220531173236-10.png]]
275 275  
225 +Check ChripStack downlink DataRate
276 276  
277 -== 6.1  Configure Packet Forwarder ==
278 278  
279 -
280 -In the Dragino gateway web interface, you need to configure the Packet Forwarder so that it forwards its data to the port. localhost:1700 or 127.0.0.1:1700
281 -
282 -* In the (% style="color:blue" %)**LoRaWAN** (%%)menu, click on (% style="color:blue" %)**LoRaWAN ~-~- Semtech UDP**
283 -
284 -* Make sure the following settings are set:
285 -** **Service Provider:** //~-~-Custom/Private LoRaWAN~-~-//
286 -** **LoRaWAN Server Address:** //localhost or 127.0.0.1//
287 -** **Server port for upstream:** //1700//
288 -** **Server port for downstream:** //1700//
289 -
290 - Click (% style="color:blue" %)**Save & Apply**.
291 -
292 -[[image:image-20221222114220-2.png||height="748" width="931"]]
293 -
294 -
295 -== 6.2  Configuring gateway frequency ==
296 -
297 -
298 -(% style="color:red" %)**Note: Gateway frequencies must match**
299 -
300 -[[image:image-20221222134830-3.png||height="408" width="923"]]
301 -
302 -
303 -== 6.3  Generate and modify the gateway-bridge configuration file ==
304 -
305 -
306 -**1）Generate the gateway-bridge configuration file**
307 -
308 -By default, the configuration file is not up-to-date,so the user needs to rebuild the gateway-bridge configuration file.
309 -
310 -Users need to access the command line of the gateway through SSH,Then type the following command:
311 -
312 -(% class="box infomessage" %)
313 -(((
314 -**/opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge configfile > /etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml **
315 -)))
316 -
317 -
318 -**2）modify the gateway-bridge configuration file**
319 -
320 -The user needs to modify the server address in line 252 in the configuration file
321 -
322 -(% class="box infomessage" %)
323 -(((
324 -**vim /etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml **
325 -)))
326 -
327 -[[image:image-20230415165254-1.png||height="583" width="956"]]
328 -
329 -
330 -== 6.4  Debug ==
331 -
332 -
333 -After the above configuration is completed, the user can enter the command to debug the gateway-bridge connection
334 -
335 -(% class="box infomessage" %)
336 -(((
337 -**/opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge ~-~-config /etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml**
338 -)))
339 -
340 -If the gateway-bridge connection is normal, the debug log displays **"connected to mqtt broker"**.
341 -
342 -[[image:image-20230415170404-2.png]]
343 -
344 -
345 -If the debug log shows "**connection error**", check that the server port or server is correct
346 -
347 -[[image:image-20230415170854-3.png]]
348 -
349 -
350 -More information can be found on the **[[ChirpStack website>>https://www.chirpstack.io/docs/]]**or **[[Forum>>url:https://forum.chirpstack.io/]]**
351 -
352 -
353 -== 6.5  (Re)start and stop gateway-bridge ==
354 -
355 -
356 -Use the following commands to (re)start and stop the ChirpStack Gateway Bridge Service:
357 -
358 -(% class="box infomessage" %)
359 -(((
360 -**# start**
361 -
362 -/etc/init.d/chirpstack-gateway-bridge start
363 -
364 -**# stop**
365 -
366 -/etc/init.d/chirpstack-gateway-bridge stop
367 -
368 -**# restart**
369 -
370 -/etc/init.d/chirpstack-gateway-bridge restart
371 -)))
372 -
373 -
374 -= 7.  How the gateway connects to Chirpstack v4 via gateway-bridge =
375 -
376 -
377 -(% style="color:blue" %)**Below list the support products and Requirements:**
378 -
379 -1. LoRaWAN Gateway model: [[LIG16>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/171-lig16.html]], [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]], [[DLOS8>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/160-dlos8.html]] ,[[LPS8>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/148-lps8.html]],[[LPS8N>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/200-lps8n.html]],[[LG308N>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/229-lg308n.html]],[[DLOS8N>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/225-dlos8n.html]]
380 -1. Firmware version since: [[Chirpstack-Bridge-V4>>https://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/Chirpstack-gateway-bridge/Chirpstack-Bridge-V4--build-v5.4.1670655072-20221210-1452/]]
381 -
382 -(% style="color:blue" %)**What do you need to prepare**
383 -
384 -A gateway that can access the internet normally
385 -
386 -
387 -== 7.1  Configure Packet Forwarder ==
388 -
389 -
390 -In the Dragino gateway web interface, you need to configure the Packet Forwarder so that it forwards its data to the port. localhost:1700 or 127.0.0.1:1700
391 -
392 -* In the (% style="color:blue" %)**LoRaWAN**(%%) menu, click on (% style="color:blue" %)**LoRaWAN ~-~- Semtech UDP**
393 -
394 -* Make sure the following settings are set:
395 -** **Service Provider:** //~-~-Custom/Private LoRaWAN~-~-//
396 -** **LoRaWAN Server Address:** //localhost or 127.0.0.1//
397 -** **Server port for upstream:** //1700//
398 -** **Server port for downstream:** //1700//
399 -
400 - Click (% style="color:blue" %)**Save & Apply**.
401 -
402 -[[image:image-20221222114220-2.png||height="748" width="931"]]
403 -
404 -
405 -== 7.2  Configuring gateway frequency ==
406 -
407 -
408 -(% style="color:red" %)**Note: Gateway frequencies must match**
409 -
410 -[[image:image-20221222134830-3.png||height="408" width="923"]]
411 -
412 -
413 -== 7.3  Modify the gateway-bridge configuration file ==
414 -
415 -
416 -Run the gateway command line command to modify the gateway-bridge configuration file:
417 -
418 -(% class="box infomessage" %)
419 -(((
420 -**root@dragino-1d27d4:~~#  vim /etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml **
421 -)))
422 -
423 -[[image:image-20221222113302-1.png]]
424 -
425 -
426 -[[image:image-20221222140203-4.png||height="875" width="806"]]
427 -
428 -
429 -Configure the server address to which the gateway needs to be connected,"tcp:~/~/chirpstack_address:1883"
430 -
431 -[[image:image-20221230094246-1.png||height="768" width="783"]]
432 -
433 -(% class="wikigeneratedid" id="H" %)
434 -After the modification, run the following command: **/etc/init.d/chirpstack-gateway-bridge restart**
435 -
436 -
437 -== 7.4  (Re)start and stop gateway-bridge ==
438 -
439 -
440 -Use the following commands to (re)start and stop the ChirpStack Gateway Bridge Service:
441 -
442 -(% class="box infomessage" %)
443 -(((
444 -**# start**
445 -
446 -/etc/init.d/chirpstack-gateway-bridge start
447 -
448 -**# stop**
449 -
450 -/etc/init.d/chirpstack-gateway-bridge stop
451 -
452 -**# restart**
453 -
454 -/etc/init.d/chirpstack-gateway-bridge restart
455 -)))
456 -
457 -
458 -== 7.5  Successful Connection ==
459 -
460 -
461 -[[image:image-20221222141754-5.png||height="488" width="1150"]]
462 -
463 -
464 -[[image:image-20221222141830-6.png||height="582" width="1153"]]
465 -
466 -
467 -= 8.  Downlink =
468 -
469 -
470 -=== 8.1 Chirpstack Downlink Note ===
471 -
472 -
473 -==== Select HEX format for downlink ====
474 -
475 -
476 -(% style="color:red" %)**Note: The end node user manual provides HEX format of the downlink commands, so users can directly select HEX format downlink.**
477 -
478 -
479 -[[image:image-20231108171112-5.png||height="629" width="1117"]]
480 -
481 -
482 -[[image:image-20231108171145-6.png||height="497" width="1101"]]
483 -
484 -
485 -
486 -
487 -
488 -[[image:image-20220531173236-10.png||height="597" width="1215"]]
489 -
490 -**Check ChripStack downlink DataRate**
491 -
492 -
493 -
494 494  [[image:image-20220525101326-11.png]]
495 495  
496 -**Make sure the RX2DR is the same in the end node**
230 +Make sure the RX2DR is the same in the end node
497 497  
498 498  
499 -== 8.3  Loraserver Downlink Note ==
500 500  
234 +== 4.2  Loraserver Downlink Note ==
501 501  
236 +
502 502  User can use MQTT to send downlink payload to ChirpStack to perform downstream to LoRaWAN End
503 503  
504 504  (((
... ... @@ -516,7 +516,7 @@
516 516  [[image:image-20220531173419-11.png]]
517 517  
518 518  (((
519 -**MQTT Connect to ChirpStack**
254 +MQTT Connect to ChirpStack
520 520  
521 521  
522 522  
... ... @@ -543,14 +543,26 @@
543 543  
544 544  [[image:image-20220531173519-12.png]]
545 545  
546 -**MQTT Connect to ChirpStack**
281 +MQTT Connect to ChirpStack
547 547  
548 548  
549 -
550 550  (((
551 -Downlink payload encode javescript code.
285 +(% style="color:red" %)**Note: Chirpstack use base64 to downlink, so need to convert the downlink payload from HEX to base64 [[https:~~/~~/base64.us/>>url:https://base64.us/]]**
286 +)))
552 552  
553 -We can run the following Javsscript code on the site:
288 +[[image:image-20220531173601-13.png]]
289 +
290 +Choose to Use Hex for Encode
291 +
292 +
293 +
294 +If we want send downstream hex 030101 to end node, the BASE64 payload is AwEB
295 +
296 +[[image:image-20220531173658-14.png]]
297 +
298 +
299 +(((
300 +Downlink payload encode javescript code: 可以在网站上运行以下Javsscript代码：
554 554  )))
555 555  
556 556  (% class="box" %)
... ... @@ -566,15 +566,15 @@
566 566   {
567 567   if(sha1[n] >= 'A' && sha1[n] <= 'Z')
568 568   {
569 - ascv = sha1.charCodeAt( n ) - 55;
316 + ascv = sha1.charCodeAt(n) - 55;
570 570   }
571 571   else if(sha1[n] >= 'a' && sha1[n] <= 'z')
572 572   {
573 - ascv = sha1.charCodeAt( n ) - 87;
320 + ascv = sha1.charCodeAt(n) - 87;
574 574   }
575 575   else
576 576   {
577 - ascv = sha1.charCodeAt( n ) - 48;
324 + ascv = sha1.charCodeAt(n) - 48;
578 578   }
579 579  \\ bit_arr = (bit_arr << 4) | ascv;
580 580   bit_num += 4;
... ... @@ -611,16 +611,15 @@
611 611  )))
612 612  
613 613  
614 -== 8.4  Add the decode function in Chirpstack for the payload ==
615 615  
362 +== 4.3  Add the decode function in Chirpstack for the payload ==
616 616  
364 +
617 617  User enters the payload code according to the steps.
618 618  
619 -Add the node device decoder you are using. The decoder for each node device is different. The decoder is found in this link: **[[decoder for dragino end node>>https://github.com/dragino/dragino-end-node-decoder]]**
367 +[[image:image-20220531173754-15.png]]
620 620  
621 -[[image:image-20220531173754-15.png||height="474" width="1334"]]
622 622  
623 -
624 624  [[image:image-20220531173856-16.png]]
625 625  
626 626  
... ... @@ -629,9 +629,10 @@
629 629  [[image:image-20220531174046-19.png]]
630 630  
631 631  
632 -= 9.  Multiply Uplink in ChirpStack =
633 633  
379 += 5.  Multiply Uplink in ChirpStack =
634 634  
381 +
635 635  (((
636 636  nbtrans field is the value to determine the re-transmission time for unconfirmed uplink data.
637 637  )))
... ... @@ -642,7 +642,7 @@
642 642  
643 643  )))
644 644  
645 -[[image:image-20220526091912-7.png||height="241" width="1336"]]
392 +[[image:image-20220526091912-7.png]]
646 646  
647 647  
648 648  (((
... ... @@ -667,18 +667,22 @@
667 667  
668 668  
669 669  
670 -**Duplicate transmission in short time**
417 +Duplicate transmission in short time
671 671  
672 -[[image:image-20220601102430-1.png||height="508" width="1120"]]
419 +[[image:image-20220601102430-1.png]]
673 673  
674 674  
675 -== 9.1  Solution ==
676 676  
423 +== 5.1  Solution ==
677 677  
425 +
678 678  This example uses the Windows version as a template, other versions can refer to this. Similiar reference: [[https:~~/~~/confluence.alitecs.de/plugins/servlet/mobile?contentId=79790102#content/view/79790102>>url:https://confluence.alitecs.de/plugins/servlet/mobile?contentId=79790102#content/view/79790102]]
679 679  
428 +
680 680  (((
681 -(% style="color:blue" %)**1.  Install the GO compilation environment: Download the corresponding version of the Go compiler at [[https:~~/~~/go.dev/dl/>>url:https://go.dev/dl/]] and install it.**
430 +(% style="color:blue" %)**1. Install the GO compilation environment: Download the corresponding version of the Go compiler at [[https:~~/~~/go.dev/dl/>>url:https://go.dev/dl/]] and install it.**
431 +
432 +
682 682  )))
683 683  
684 684  [[image:image-20220525104532-24.png]]
... ... @@ -691,7 +691,7 @@
691 691  
692 692  
693 693  (((
694 -(% style="color:blue" %)**2.  Environment variable settings:**
445 +(% style="color:blue" %)**2. Environment variable settings:**
695 695  )))
696 696  
697 697  (((
... ... @@ -716,7 +716,7 @@
716 716  
717 717  
718 718  
719 -(% style="color:blue" %)**3.  Modify the ADR configuration file according to your own needs, adr.setting.go is an example of the ADR configuration file.**
470 +(% style="color:blue" %)**3. Modify the ADR configuration file according to your own needs, adr.setting.go is an example of the ADR configuration file.**
720 720  
721 721  The name of the plugin: Example ADR plugin:
722 722  
... ... @@ -728,7 +728,7 @@
728 728  
729 729  
730 730  
731 -(% style="color:blue" %)**4.  Compile the ADR configuration file and generate the exe file.**
482 +(% style="color:blue" %)**4. Compile the ADR configuration file and generate the exe file.**
732 732  
733 733  1) Create a folder named adr-setting
734 734  
... ... @@ -754,7 +754,7 @@
754 754  
755 755  
756 756  
757 -(% style="color:blue" %)**5.  Add the plugin and run the plugin.**
508 +(% style="color:blue" %)**5. Add the plugin and run the plugin.**
758 758  
759 759  (((
760 760  The exe file generated in the previous step is placed in the same root directory as chirpstack-network-server.toml, and the ADR plugin is added to the toml file. The location of the addition is as follows:
... ... @@ -791,242 +791,16 @@
791 791  Finish.
792 792  
793 793  
794 -= 10.  How to store/get all data traffic for a specific sensor, including raw payload, and uplink/ downlink history. =
795 795  
546 += 6.  Trouble Shooting =
796 796  
797 -All data is published to the MQTT topics. if you want to store/get the data, you would have to create an MQTT handler and store the data yourself.
548 +== 6.1  MIC Mismatch or MIC Failed ==
798 798  
799 -This example will be shown how to store/get all the data in two ways:
800 800  
801 -(% style="color:blue" %)**//1). Chirpstack ~-~-> Node-red//**
802 -
803 -
804 -[[image:image-20221012184501-1.png||height="608" width="1041"]]
805 -
806 -
807 -Use MQTT in Nore-red to subscribe to topics published by the chirpstack-application and then continuously write to a file
808 -
809 -[[image:image-20221012174220-2.png]]
810 -
811 -
812 -[[image:image-20221012184655-3.png||height="395" width="1049"]]
813 -
814 -
815 -**Each message is continuously logged to a specified file**
816 -
817 -[[image:image-20221012174352-3.png]]
818 -
819 -
820 -(% style="color:blue" %)**//2). MQTT  Sub//**
821 -
822 -If you don't want to store the information via node-red, you can get the output via the subscribe command.
823 -
824 -
825 -**If connecting from the same machine, you can use the following command to receive data:**
826 -
827 -(% class="box infomessage" %)
828 828  (((
829 -**mosquitto_sub -h localhost -t "application/#" -v**
830 -)))
831 -
832 -
833 -(% style="color:blue" %)**Different host**
834 -
835 -(% class="box infomessage" %)
836 -(((
837 -**mosquitto_sub -h IPADDRESS -p 8883 ~-~-insecure ~-~-cafile ca.pem ~-~-cert cert.pem ~-~-key key.pem -t "application/#" -v**
838 -)))
839 -
840 -[[image:image-20221012173639-1.png||height="273" width="1206"]]
841 -
842 -
843 -= 11.  How to use Chirpstack API to batch register Sensor Node/Gateway in Chistapstack Server =
844 -
845 -The following example is based on the built-in ChirpStack server for LPS8V2
846 -
847 -[[image:image-20231201174640-1.png||height="584" width="1148"]]
848 -
849 -
850 -== **11.1 Generate API Tokens** ==
851 -
852 -Access the built-in chirpstack , click "**API Key**" and "**Add API Key**".
853 -
854 -[[image:image-20231201175118-2.png||height="597" width="1156"]]
855 -
856 -**Save the generated API Tokens**
857 -
858 -[[image:image-20231201175648-3.png||height="596" width="1155"]]
859 -
860 -[[image:image-20231204104802-1.png]]
861 -
862 -
863 -== **11.2 Template file** ==
864 -
865 -
866 -Click on **"Template File Download"**, the user will download a **register.csv** template file,
867 -
868 -[[image:image-20231204105201-2.png]]
869 -
870 -
871 -Before registering in batches, the user needs to add an **Application** and **Device profile**, If  you have already added them, you do not need to add them again，
872 -
873 -Open the corresponding **Application** and **Device profile** and copy their IDs
874 -
875 -[[image:image-20231204110902-5.png||height="618" width="1197"]]
876 -
877 -[[image:image-20231204111116-7.png||height="619" width="1199"]]
878 -
879 -[[image:image-20231204111834-9.png||height="273" width="1205"]]
880 -
881 -[[image:image-20231204112107-10.png||height="621" width="1203"]]
882 -
883 -
884 -
885 -== **11.3 Batch Register** ==
886 -
887 -[[image:image-20231204113136-11.png||height="362" width="1062"]]
888 -
889 -
890 -**Check whether the batch registration is successful**
891 -
892 -[[image:image-20231204113212-12.png]]
893 -
894 -[[image:image-20231204113237-13.png||height="558" width="1081"]]
895 -
896 -
897 -
898 -= 12.  Example: Use Local Server ChirpStack and Node-Red in LPS8v2 =
899 -
900 -
901 -LPS8v2 includes a local ChirpStack Server and Node-Red. This example shows how to configure LHT65N to use with the local Node-Red server. This example assumes users already have:
902 -
903 -* LHT65N register on LPS8v2 Built-In ChirpStack server already
904 -* The user is able to see the data on the built-in ChirpStack server device page.
905 -
906 -Below are the steps to plot the sensor data on LPS8v2 Node-Red.
907 -
908 -
909 -== 12.1 Link Node-Red to Local ChirpStack ==
910 -
911 -
912 -Users can download the Node-Red decoder from this link and import it into the Node-Red platform:  **[[attach:LHT65N-ChirpStack-node-red.json||target="_blank"]]**
913 -
914 -For more information on importing Input Flow, check out this link: **[[Import Input Flow for Dragino Sensors>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Node-RED/#H3.A0ImportInputFlowforDraginoSensors]]**
915 -
916 -After importing the Input Flow is complete, the user needs to edit the MQTT in the node
917 -
918 -
919 -(% style="color:blue" %)**1. Change the Topic**
920 -
921 -Topic modifies it to the following format:
922 -
923 -**application/(% style="color:red" %)Application ID(%%)/device/(% style="color:red" %)End device ID(%%)/event/up**
924 -
925 -Reference link: [[**Node-RED integration** >>https://www.chirpstack.io/docs/guides/node-red-integration.html]]
926 -
927 -[[image:image-20230527143923-1.png||height="588" width="1132"]]
928 -
929 -
930 -
931 -(% style="color:blue" %)**2. Enter the MQTT configuration information**
932 -
933 -[[image:image-20230527144206-2.png||height="590" width="1136"]]
934 -
935 -
936 -(% style="color:blue" %)**3.** **Finally, click "Update" and Deploy**
937 -
938 -"Connected" indicates that the Link Node-red to Local Chirpstack is normal.
939 -
940 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/Notes%20for%20TTN/WebHome/image-20220914140918-5.png?width=1121&height=602&rev=1.1||alt="image-20220914140918-5.png"]]
941 -
942 -
943 -== 12.2 Check result. ==
944 -
945 -
946 -Users can check logs by adding debug.
947 -
948 -Browser access: **Node-Red-Server-Address:1880/ui**
949 -
950 -[[image:image-20230529150923-1.png||height="424" width="1118"]]
951 -
952 -
953 -= 13.  Trouble Shooting =
954 -
955 -== 13.1  MIC Mismatch or MIC Failed ==
956 -
957 -
958 -(((
959 959  When the device is registered or the device is working normally, the problem of MIC mismatch and MIC failed occurs.
960 960  )))
961 961  
962 962  (((
963 963  Under normal circumstances, users need to change the APPKEY to solve this problem.
964 -
965 -
966 -== 13.2  The node is very close to the gateway, but the signal is poor ==
967 -
968 -
969 -If you are using US915 or AU915, you found the frequency points of different subband ranges in your uplink
970 -
971 -Like that：Both 905.1Mhz and 902.3Mhz appear on uplink
972 - But they belong to Subband1 and Subband2 of US915 respectively
973 -
974 -Cause: The server and the gateway use different frequency bands (the server uses Subband1, and the gateway uses Subband2)
975 -
976 - In server side, it shows the frequency is 905.1Mhz, which is sub-band2. But the RSSI is very low, Because this is not a signal in 905.1Mhz, it is on 902.3Mhz, the signal is too strong and appear a noise in 905.1Mhz.
977 -
978 -How to check the frequency band used by the server：
979 -
980 -You can view the information sent by the server: ch_mask in Unconfirmdedatadown
981 -
982 -[[image:image-20230821113255-1.png]]
983 -
984 -According to lorawan's protocol, your first ch_mask is 7 for ChMaskCntl = 7 then 125 kHz channels are disabled. Simultaneously the channels 64 to 71 are set according to the ChMask bit mask.
985 -
986 -[[image:image-20230821113539-2.png]]
987 -
988 -In the second message, the channel 0~~7 is true, which means that your server is using subband2.
989 -
990 -[[image:image-20230821113618-3.png]]
991 -
992 -**Note: lorawan's protocol link——[[LoRaWAN® Regional Parameters v1.0.3revA (lora-alliance.org)>>url:https://resources.lora-alliance.org/document/lorawan-regional-parameters-v1-0-3reva]]**
993 -
994 -
995 -
996 -
997 -== 13.3 How to get the log information of the node？ ==
998 -
999 -
1000 -~1. Get information about a single node.
1001 -
1002 -* Download this file in the node's live data interface.
1003 -
1004 -[[image:image-20240117173123-1.png||height="526" width="1086"]]
1005 -
1006 -* The LoRaWAN frames download gateway receives real-time data from the current node.
1007 -
1008 -[[image:image-20240117174452-2.png||height="525" width="1081"]]
1009 -
1010 -
1011 -2. Get information about the entire Gateway.
1012 -
1013 -* Click to select the online gateway of the current node.
1014 -
1015 -[[image:image-20240117175058-4.png||height="532" width="1077"]]
1016 -
1017 -
1018 -* Download this file on the LoRaWAN frames interface.
1019 -
1020 -[[image:image-20240117175009-3.png||height="524" width="1076"]]
1021 -
1022 -
1023 -
1024 -After the data collection is completed, you can send this file directly to our technical support personnel for analysis.
1025 -
1026 -
1027 -You can also use the packet analysis tool developed by our company to check it yourself. Please refer to the following [[link>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20of%20Dragino%20LoRaWAN%20Packet%20Analyze%20Tool/#H4.Chirpstack]] to use this tool.
1028 -
1029 -[[image:image-20240117175738-5.png]]
1030 -
1031 -== ==
1032 1032  )))
LHT65N-ChirpStack-node-red.json
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -18.9 KB
Content
... ... @@ -1,721 +1,0 @@
1 -[
2 - {
3 - "id": "0f8b93c6ce9ba9bd",
4 - "type": "tab",
5 - "label": "流程 1",
6 - "disabled": false,
7 - "info": "",
8 - "env": []
9 - },
10 - {
11 - "id": "11ea7050721f9df5",
12 - "type": "mqtt in",
13 - "z": "0f8b93c6ce9ba9bd",
14 - "name": "LHT65N",
15 - "topic": "application/43b0fd94-75be-4a80-a78c-c9381fe23b05/device/a84041c8b1824695/event/up",
16 - "qos": "0",
17 - "datatype": "auto-detect",
18 - "broker": "862a790de52f4ea4",
19 - "nl": false,
20 - "rap": true,
21 - "rh": 0,
22 - "inputs": 0,
23 - "x": 100,
24 - "y": 140,
25 - "wires": [
26 - [
27 - "034db5cd68129249",
28 - "6e4c3938ccd21838",
29 - "d20a25c0a12cad04",
30 - "38136d7454e138e5",
31 - "239852361ed7c91d"
32 - ]
33 - ]
34 - },
35 - {
36 - "id": "6e4c3938ccd21838",
37 - "type": "debug",
38 - "z": "0f8b93c6ce9ba9bd",
39 - "name": "",
40 - "active": true,
41 - "tosidebar": true,
42 - "console": false,
43 - "tostatus": false,
44 - "complete": "false",
45 - "statusVal": "",
46 - "statusType": "auto",
47 - "x": 490,
48 - "y": 140,
49 - "wires": []
50 - },
51 - {
52 - "id": "034db5cd68129249",
53 - "type": "function",
54 - "z": "0f8b93c6ce9ba9bd",
55 - "name": "",
56 - "func": "var data = msg.payload[\"deviceInfo\"]\nvar decode = msg.payload[\"object\"]\nif (decode[\"Ext_sensor\"] == \"Temperature Sensor\"){\nvar f_port = msg.payload[\"fPort\"]\nvar f_cnt = msg.payload[\"fCnt\"]\nvar data2 = decode\nvar bat =data2[\"BatV\"]\nvar bat_status=data2[\"Bat_status\"]\nvar ext_sensor=data2[\"Ext_sensor\"]\nvar hum_SHT=data2[\"Hum_SHT\"]\nif (\"TempC_DS\" in data2){\n var tempC_DS=data2[\"TempC_DS\"]\n}\nelse {\ntempC_DS=data2[\"TempC_TMP117\"]\n}\nvar tempC_SHT=data2[\"TempC_SHT\"]\nvar a1={payload:f_port},a2={payload:f_cnt},a3={payload:bat},a4={payload:bat_status},a5={payload:ext_sensor},\n a6={payload:hum_SHT},a7={payload:tempC_DS},a8={payload:tempC_SHT}\nreturn [a1,a2,a3,a4,a5,a6,a7,a8];\n}",
57 - "outputs": 9,
58 - "noerr": 0,
59 - "initialize": "",
60 - "finalize": "",
61 - "libs": [],
62 - "x": 470,
63 - "y": 260,
64 - "wires": [
65 - [
66 - "054041c1f8ad740a"
67 - ],
68 - [
69 - "11286fbcb9419c65"
70 - ],
71 - [
72 - "6f74bac1ba605862"
73 - ],
74 - [
75 - "c9f618cca24db5e1"
76 - ],
77 - [
78 - "7f2fc42c4bcc6ff9"
79 - ],
80 - [
81 - "980646824d0c5239"
82 - ],
83 - [
84 - "a2ed445e50c952ea"
85 - ],
86 - [
87 - "13394b6f113fe555"
88 - ],
89 - []
90 - ]
91 - },
92 - {
93 - "id": "054041c1f8ad740a",
94 - "type": "ui_text",
95 - "z": "0f8b93c6ce9ba9bd",
96 - "group": "6c8dcef19b33b1ab",
97 - "order": 0,
98 - "width": 0,
99 - "height": 0,
100 - "name": "f_port",
101 - "label": "f_port",
102 - "format": "{{msg.payload}}",
103 - "layout": "row-spread",
104 - "className": "",
105 - "x": 770,
106 - "y": 160,
107 - "wires": []
108 - },
109 - {
110 - "id": "11286fbcb9419c65",
111 - "type": "ui_text",
112 - "z": "0f8b93c6ce9ba9bd",
113 - "group": "9d9e40253fa3a62f",
114 - "order": 0,
115 - "width": 0,
116 - "height": 0,
117 - "name": "f_cunt",
118 - "label": "f_cunt",
119 - "format": "{{msg.payload}}",
120 - "layout": "row-spread",
121 - "className": "",
122 - "x": 770,
123 - "y": 200,
124 - "wires": []
125 - },
126 - {
127 - "id": "6f74bac1ba605862",
128 - "type": "ui_chart",
129 - "z": "0f8b93c6ce9ba9bd",
130 - "name": "bat",
131 - "group": "b24db75b1499c15f",
132 - "order": 0,
133 - "width": 0,
134 - "height": 0,
135 - "label": "bat",
136 - "chartType": "line",
137 - "legend": "false",
138 - "xformat": "HH:mm:ss",
139 - "interpolate": "linear",
140 - "nodata": "",
141 - "dot": false,
142 - "ymin": "",
143 - "ymax": "",
144 - "removeOlder": 1,
145 - "removeOlderPoints": "",
146 - "removeOlderUnit": "3600",
147 - "cutout": 0,
148 - "useOneColor": false,
149 - "useUTC": false,
150 - "colors": [
151 - "#1f77b4",
152 - "#aec7e8",
153 - "#ff7f0e",
154 - "#2ca02c",
155 - "#98df8a",
156 - "#d62728",
157 - "#ff9896",
158 - "#9467bd",
159 - "#c5b0d5"
160 - ],
161 - "outputs": 1,
162 - "useDifferentColor": false,
163 - "className": "",
164 - "x": 770,
165 - "y": 240,
166 - "wires": [
167 - []
168 - ]
169 - },
170 - {
171 - "id": "c9f618cca24db5e1",
172 - "type": "ui_text",
173 - "z": "0f8b93c6ce9ba9bd",
174 - "group": "758898c4bead5e6f",
175 - "order": 6,
176 - "width": 0,
177 - "height": 0,
178 - "name": "Bat_status",
179 - "label": "Bat_status",
180 - "format": "{{msg.payload}}",
181 - "layout": "row-spread",
182 - "className": "",
183 - "x": 790,
184 - "y": 280,
185 - "wires": []
186 - },
187 - {
188 - "id": "7f2fc42c4bcc6ff9",
189 - "type": "ui_text",
190 - "z": "0f8b93c6ce9ba9bd",
191 - "group": "a8f02d8f9b3e80a1",
192 - "order": 0,
193 - "width": 0,
194 - "height": 0,
195 - "name": "Ext_sensor",
196 - "label": "Ext_sensor",
197 - "format": "{{msg.payload}}",
198 - "layout": "row-spread",
199 - "className": "",
200 - "x": 790,
201 - "y": 320,
202 - "wires": []
203 - },
204 - {
205 - "id": "980646824d0c5239",
206 - "type": "ui_chart",
207 - "z": "0f8b93c6ce9ba9bd",
208 - "name": "Hum_SHT",
209 - "group": "a9ef53ea130e5557",
210 - "order": 6,
211 - "width": 0,
212 - "height": 0,
213 - "label": "Hum_SHT",
214 - "chartType": "line",
215 - "legend": "false",
216 - "xformat": "HH:mm:ss",
217 - "interpolate": "linear",
218 - "nodata": "",
219 - "dot": false,
220 - "ymin": "",
221 - "ymax": "",
222 - "removeOlder": 1,
223 - "removeOlderPoints": "",
224 - "removeOlderUnit": "3600",
225 - "cutout": 0,
226 - "useOneColor": false,
227 - "useUTC": false,
228 - "colors": [
229 - "#1f77b4",
230 - "#aec7e8",
231 - "#ff7f0e",
232 - "#2ca02c",
233 - "#98df8a",
234 - "#d62728",
235 - "#ff9896",
236 - "#9467bd",
237 - "#c5b0d5"
238 - ],
239 - "outputs": 1,
240 - "useDifferentColor": false,
241 - "className": "",
242 - "x": 790,
243 - "y": 360,
244 - "wires": [
245 - []
246 - ]
247 - },
248 - {
249 - "id": "a2ed445e50c952ea",
250 - "type": "ui_chart",
251 - "z": "0f8b93c6ce9ba9bd",
252 - "name": "TempC_sensor",
253 - "group": "1558cd7a030388f7",
254 - "order": 6,
255 - "width": 0,
256 - "height": 0,
257 - "label": "TempC_sensor",
258 - "chartType": "line",
259 - "legend": "false",
260 - "xformat": "HH:mm:ss",
261 - "interpolate": "linear",
262 - "nodata": "",
263 - "dot": false,
264 - "ymin": "",
265 - "ymax": "",
266 - "removeOlder": 1,
267 - "removeOlderPoints": "",
268 - "removeOlderUnit": "3600",
269 - "cutout": 0,
270 - "useOneColor": false,
271 - "useUTC": false,
272 - "colors": [
273 - "#1f77b4",
274 - "#aec7e8",
275 - "#ff7f0e",
276 - "#2ca02c",
277 - "#98df8a",
278 - "#d62728",
279 - "#ff9896",
280 - "#9467bd",
281 - "#c5b0d5"
282 - ],
283 - "outputs": 1,
284 - "useDifferentColor": false,
285 - "className": "",
286 - "x": 800,
287 - "y": 400,
288 - "wires": [
289 - []
290 - ]
291 - },
292 - {
293 - "id": "13394b6f113fe555",
294 - "type": "ui_chart",
295 - "z": "0f8b93c6ce9ba9bd",
296 - "name": "TempC_SHT",
297 - "group": "f523098714ee6cd6",
298 - "order": 6,
299 - "width": 0,
300 - "height": 0,
301 - "label": "TempC_SHT",
302 - "chartType": "line",
303 - "legend": "false",
304 - "xformat": "HH:mm:ss",
305 - "interpolate": "linear",
306 - "nodata": "",
307 - "dot": false,
308 - "ymin": "",
309 - "ymax": "",
310 - "removeOlder": 1,
311 - "removeOlderPoints": "",
312 - "removeOlderUnit": "3600",
313 - "cutout": 0,
314 - "useOneColor": false,
315 - "useUTC": false,
316 - "colors": [
317 - "#1f77b4",
318 - "#aec7e8",
319 - "#ff7f0e",
320 - "#2ca02c",
321 - "#98df8a",
322 - "#d62728",
323 - "#ff9896",
324 - "#9467bd",
325 - "#c5b0d5"
326 - ],
327 - "outputs": 1,
328 - "useDifferentColor": false,
329 - "className": "",
330 - "x": 790,
331 - "y": 440,
332 - "wires": [
333 - []
334 - ]
335 - },
336 - {
337 - "id": "d20a25c0a12cad04",
338 - "type": "function",
339 - "z": "0f8b93c6ce9ba9bd",
340 - "name": "",
341 - "func": "var data = msg.payload[\"deviceInfo\"]\nvar decode = msg.payload[\"object\"]\nif (decode[\"Work_mode\"]==\"Interrupt Sensor send\"){\nvar f_port = msg.payload[\"fPort\"]\nvar f_cnt = msg.payload[\"fCnt\"]\nvar data2 = decode\nvar bat =data2[\"BatV\"]\nvar bat_status=data2[\"Bat_status\"]\nvar work_mode=data2[\"Work_mode\"]\nvar exti_pin_level=data2[\"Exti_pin_level\"]\nvar exti_status=data2[\"Exti_status\"]\nvar hum_SHT=data2[\"Hum_SHT\"]\nvar tempC_SHT=data2[\"TempC_SHT\"]\nvar a1={payload:f_port},a2={payload:f_cnt},a3={payload:bat},a4={payload:bat_status},a5={payload:work_mode},\na6={payload:exti_pin_level},a7={payload:exti_status},a8={payload:hum_SHT},a9={payload:tempC_SHT}\nreturn [a1,a2,a3,a4,a5,a6,a7,a8,a9];\n}",
342 - "outputs": 9,
343 - "noerr": 0,
344 - "initialize": "",
345 - "finalize": "",
346 - "libs": [],
347 - "x": 470,
348 - "y": 440,
349 - "wires": [
350 - [
351 - "054041c1f8ad740a"
352 - ],
353 - [
354 - "11286fbcb9419c65"
355 - ],
356 - [
357 - "6f74bac1ba605862"
358 - ],
359 - [
360 - "c9f618cca24db5e1"
361 - ],
362 - [
363 - "7f2fc42c4bcc6ff9"
364 - ],
365 - [
366 - "0513bcb70cd63787"
367 - ],
368 - [
369 - "10eed06366dc18c4"
370 - ],
371 - [
372 - "980646824d0c5239"
373 - ],
374 - [
375 - "13394b6f113fe555"
376 - ]
377 - ]
378 - },
379 - {
380 - "id": "0513bcb70cd63787",
381 - "type": "ui_text",
382 - "z": "0f8b93c6ce9ba9bd",
383 - "group": "b1dc3cad430eb5b7",
384 - "order": 0,
385 - "width": 0,
386 - "height": 0,
387 - "name": "Exti_pin_level",
388 - "label": "Exti_pin_level",
389 - "format": "{{msg.payload}}",
390 - "layout": "row-spread",
391 - "className": "",
392 - "x": 780,
393 - "y": 560,
394 - "wires": []
395 - },
396 - {
397 - "id": "10eed06366dc18c4",
398 - "type": "ui_text",
399 - "z": "0f8b93c6ce9ba9bd",
400 - "group": "4184be11e1179998",
401 - "order": 0,
402 - "width": 0,
403 - "height": 0,
404 - "name": "Exti_status",
405 - "label": "Exti_status",
406 - "format": "{{msg.payload}}",
407 - "layout": "row-spread",
408 - "className": "",
409 - "x": 770,
410 - "y": 600,
411 - "wires": []
412 - },
413 - {
414 - "id": "38136d7454e138e5",
415 - "type": "function",
416 - "z": "0f8b93c6ce9ba9bd",
417 - "name": "",
418 - "func": "var data = msg.payload[\"deviceInfo\"]\nvar decode = msg.payload[\"object\"]\nif (decode[\"Work_mode\"]==\"Interrupt Sensor count\"){\nvar f_port = msg.payload[\"fPort\"]\nvar f_cnt = msg.payload[\"fCnt\"]\nvar data2 = decode\nvar bat =data2[\"BatV\"]\nvar bat_status=data2[\"Bat_status\"]\nvar work_mode=data2[\"Work_mode\"]\nvar exit_count=data2[\"Exit_count\"]\nvar hum_SHT=data2[\"Hum_SHT\"]\nvar tempC_SHT=data2[\"TempC_SHT\"]\nvar a1={payload:f_port},a2={payload:f_cnt},a3={payload:bat},a4={payload:bat_status},a5={payload:work_mode},\na6={payload:exit_count},a8={payload:hum_SHT},a9={payload:tempC_SHT}\nreturn [a1,a2,a3,a4,a5,a6,a8,a9];\n}",
419 - "outputs": 8,
420 - "noerr": 0,
421 - "initialize": "",
422 - "finalize": "",
423 - "libs": [],
424 - "x": 470,
425 - "y": 620,
426 - "wires": [
427 - [
428 - "054041c1f8ad740a"
429 - ],
430 - [
431 - "11286fbcb9419c65"
432 - ],
433 - [
434 - "6f74bac1ba605862"
435 - ],
436 - [
437 - "c9f618cca24db5e1"
438 - ],
439 - [
440 - "7f2fc42c4bcc6ff9"
441 - ],
442 - [
443 - "3914f37c12607c9f"
444 - ],
445 - [
446 - "980646824d0c5239"
447 - ],
448 - [
449 - "13394b6f113fe555"
450 - ]
451 - ]
452 - },
453 - {
454 - "id": "3914f37c12607c9f",
455 - "type": "ui_text",
456 - "z": "0f8b93c6ce9ba9bd",
457 - "group": "28cf5cca4c2c0bb5",
458 - "order": 0,
459 - "width": 0,
460 - "height": 0,
461 - "name": "exit_count",
462 - "label": "exit_count",
463 - "format": "{{msg.payload}}",
464 - "layout": "row-spread",
465 - "className": "",
466 - "x": 790,
467 - "y": 700,
468 - "wires": []
469 - },
470 - {
471 - "id": "239852361ed7c91d",
472 - "type": "function",
473 - "z": "0f8b93c6ce9ba9bd",
474 - "name": "",
475 - "func": "var data = msg.payload[\"deviceInfo\"]\nvar decode = msg.payload[\"object\"]\nif (decode[\"Work_mode\"]==\"ADC Sensor\"){\nvar f_port = msg.payload[\"fPort\"]\nvar f_cnt = msg.payload[\"fCnt\"]\nvar data2 = decode\nvar bat =data2[\"BatV\"]\nvar bat_status=data2[\"Bat_status\"]\nvar work_mode=data2[\"Work_mode\"]\nvar adc_V=data2[\"ADC_V\"]\nvar hum_SHT=data2[\"Hum_SHT\"]\nvar tempC_SHT=data2[\"TempC_SHT\"]\nvar a1={payload:f_port},a2={payload:f_cnt},a3={payload:bat},a4={payload:bat_status},a5={payload:work_mode},\na6={payload:adc_V},a8={payload:hum_SHT},a9={payload:tempC_SHT}\nreturn [a1,a2,a3,a4,a5,a6,a8,a9];\n}",
476 - "outputs": 8,
477 - "noerr": 0,
478 - "initialize": "",
479 - "finalize": "",
480 - "libs": [],
481 - "x": 470,
482 - "y": 760,
483 - "wires": [
484 - [
485 - "054041c1f8ad740a"
486 - ],
487 - [
488 - "11286fbcb9419c65"
489 - ],
490 - [
491 - "6f74bac1ba605862"
492 - ],
493 - [
494 - "c9f618cca24db5e1"
495 - ],
496 - [
497 - "7f2fc42c4bcc6ff9"
498 - ],
499 - [
500 - "605688b5e60df43d"
501 - ],
502 - [
503 - "980646824d0c5239"
504 - ],
505 - [
506 - "13394b6f113fe555"
507 - ]
508 - ]
509 - },
510 - {
511 - "id": "605688b5e60df43d",
512 - "type": "ui_chart",
513 - "z": "0f8b93c6ce9ba9bd",
514 - "name": "ADC_V",
515 - "group": "5f974d1fd1c0edfa",
516 - "order": 0,
517 - "width": 0,
518 - "height": 0,
519 - "label": "ADC_V",
520 - "chartType": "line",
521 - "legend": "false",
522 - "xformat": "HH:mm:ss",
523 - "interpolate": "linear",
524 - "nodata": "",
525 - "dot": false,
526 - "ymin": "",
527 - "ymax": "",
528 - "removeOlder": 1,
529 - "removeOlderPoints": "",
530 - "removeOlderUnit": "3600",
531 - "cutout": 0,
532 - "useOneColor": false,
533 - "useUTC": false,
534 - "colors": [
535 - "#1f77b4",
536 - "#aec7e8",
537 - "#ff7f0e",
538 - "#2ca02c",
539 - "#98df8a",
540 - "#d62728",
541 - "#ff9896",
542 - "#9467bd",
543 - "#c5b0d5"
544 - ],
545 - "outputs": 1,
546 - "useDifferentColor": false,
547 - "className": "",
548 - "x": 780,
549 - "y": 780,
550 - "wires": [
551 - []
552 - ]
553 - },
554 - {
555 - "id": "862a790de52f4ea4",
556 - "type": "mqtt-broker",
557 - "name": "LHT65N",
558 - "broker": "10.130.2.143",
559 - "port": "1883",
560 - "clientid": "",
561 - "autoConnect": true,
562 - "usetls": false,
563 - "protocolVersion": "4",
564 - "keepalive": "60",
565 - "cleansession": true,
566 - "birthTopic": "",
567 - "birthQos": "0",
568 - "birthPayload": "",
569 - "birthMsg": {},
570 - "closeTopic": "",
571 - "closeQos": "0",
572 - "closePayload": "",
573 - "closeMsg": {},
574 - "willTopic": "",
575 - "willQos": "0",
576 - "willPayload": "",
577 - "willMsg": {},
578 - "userProps": "",
579 - "sessionExpiry": ""
580 - },
581 - {
582 - "id": "6c8dcef19b33b1ab",
583 - "type": "ui_group",
584 - "name": "f_port",
585 - "tab": "7e01624d2b1a030f",
586 - "order": 1,
587 - "disp": true,
588 - "width": "6",
589 - "collapse": false,
590 - "className": ""
591 - },
592 - {
593 - "id": "9d9e40253fa3a62f",
594 - "type": "ui_group",
595 - "name": "f_cunt",
596 - "tab": "7e01624d2b1a030f",
597 - "order": 2,
598 - "disp": true,
599 - "width": "6",
600 - "collapse": false,
601 - "className": ""
602 - },
603 - {
604 - "id": "b24db75b1499c15f",
605 - "type": "ui_group",
606 - "name": "bat",
607 - "tab": "7e01624d2b1a030f",
608 - "order": 8,
609 - "disp": true,
610 - "width": "6",
611 - "collapse": false,
612 - "className": ""
613 - },
614 - {
615 - "id": "758898c4bead5e6f",
616 - "type": "ui_group",
617 - "name": "Bat_status",
618 - "tab": "7e01624d2b1a030f",
619 - "order": 3,
620 - "disp": true,
621 - "width": "6",
622 - "collapse": false,
623 - "className": ""
624 - },
625 - {
626 - "id": "a8f02d8f9b3e80a1",
627 - "type": "ui_group",
628 - "name": "Ext_sensor",
629 - "tab": "7e01624d2b1a030f",
630 - "order": 4,
631 - "disp": true,
632 - "width": "6",
633 - "collapse": false,
634 - "className": ""
635 - },
636 - {
637 - "id": "a9ef53ea130e5557",
638 - "type": "ui_group",
639 - "name": "Hum_SHT",
640 - "tab": "7e01624d2b1a030f",
641 - "order": 9,
642 - "disp": true,
643 - "width": "6",
644 - "collapse": false,
645 - "className": ""
646 - },
647 - {
648 - "id": "1558cd7a030388f7",
649 - "type": "ui_group",
650 - "name": "TempC_sensor",
651 - "tab": "7e01624d2b1a030f",
652 - "order": 10,
653 - "disp": true,
654 - "width": "6",
655 - "collapse": false,
656 - "className": ""
657 - },
658 - {
659 - "id": "f523098714ee6cd6",
660 - "type": "ui_group",
661 - "name": "TempC_SHT",
662 - "tab": "7e01624d2b1a030f",
663 - "order": 11,
664 - "disp": true,
665 - "width": "6",
666 - "collapse": false,
667 - "className": ""
668 - },
669 - {
670 - "id": "b1dc3cad430eb5b7",
671 - "type": "ui_group",
672 - "name": "Exti_pin_level",
673 - "tab": "7e01624d2b1a030f",
674 - "order": 6,
675 - "disp": true,
676 - "width": "6",
677 - "collapse": false,
678 - "className": ""
679 - },
680 - {
681 - "id": "4184be11e1179998",
682 - "type": "ui_group",
683 - "name": "Exti_status",
684 - "tab": "7e01624d2b1a030f",
685 - "order": 7,
686 - "disp": true,
687 - "width": "6",
688 - "collapse": false,
689 - "className": ""
690 - },
691 - {
692 - "id": "28cf5cca4c2c0bb5",
693 - "type": "ui_group",
694 - "name": "exit_count",
695 - "tab": "7e01624d2b1a030f",
696 - "order": 5,
697 - "disp": true,
698 - "width": "6",
699 - "collapse": false,
700 - "className": ""
701 - },
702 - {
703 - "id": "5f974d1fd1c0edfa",
704 - "type": "ui_group",
705 - "name": "ADC_V",
706 - "tab": "7e01624d2b1a030f",
707 - "order": 12,
708 - "disp": true,
709 - "width": "6",
710 - "collapse": false,
711 - "className": ""
712 - },
713 - {
714 - "id": "7e01624d2b1a030f",
715 - "type": "ui_tab",
716 - "name": "LHT65N",
717 - "icon": "LHT65N",
718 - "disabled": false,
719 - "hidden": false
720 - }
721 -]
image-20221010193350-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -42.7 KB
Content
image-20221010193621-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -34.2 KB
Content
image-20221012173639-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -56.2 KB
Content
image-20221012174220-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -14.8 KB
Content
image-20221012174352-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -93.0 KB
Content
image-20221012184501-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -91.3 KB
Content
image-20221012184631-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -32.4 KB
Content
image-20221012184655-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoye
Size
... ... @@ -1,1 +1,0 @@
1 -45.4 KB
Content
image-20221222113302-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -76.3 KB
Content
image-20221222114220-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -64.3 KB
Content
image-20221222134830-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -54.5 KB
Content
image-20221222140203-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -91.4 KB
Content
image-20221222141754-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -179.1 KB
Content
image-20221222141830-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -116.7 KB
Content
image-20221230094246-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -84.9 KB
Content
image-20230415165254-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -67.2 KB
Content
image-20230415170404-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -17.9 KB
Content
image-20230415170854-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -48.4 KB
Content
image-20230527115750-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -208.8 KB
Content
image-20230527143923-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -222.4 KB
Content
image-20230527144206-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -224.2 KB
Content
image-20230529150923-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -87.2 KB
Content
image-20230531162943-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -84.6 KB
Content
image-20230702094608-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -53.8 KB
Content
image-20230702094852-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -12.5 KB
Content
image-20230702094944-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -26.7 KB
Content
image-20230702095114-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -43.5 KB
Content
image-20230702095557-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -48.5 KB
Content
image-20230702095641-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -19.2 KB
Content
image-20230702095827-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -34.9 KB
Content
image-20230702100312-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -33.2 KB
Content
image-20230702100356-9.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -21.9 KB
Content
image-20230702100543-10.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -25.6 KB
Content
image-20230702100930-11.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -48.7 KB
Content
image-20230821113255-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -115.7 KB
Content
image-20230821113539-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -71.1 KB
Content
image-20230821113618-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -19.0 KB
Content
image-20230821114047-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -125.6 KB
Content
image-20230926092907-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -64.0 KB
Content
image-20230926093057-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -69.6 KB
Content
image-20230926093233-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -95.8 KB
Content
image-20231108140540-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -46.3 KB
Content
image-20231108164914-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -37.2 KB
Content
image-20231108165128-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -43.3 KB
Content
image-20231108165158-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -60.8 KB
Content
image-20231108171112-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -47.7 KB
Content
image-20231108171145-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -39.1 KB
Content
image-20231201174640-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -43.6 KB
Content
image-20231201175118-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -83.2 KB
Content
image-20231201175648-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -103.2 KB
Content
image-20231201180103-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -52.6 KB
Content
image-20231204104802-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -42.4 KB
Content
image-20231204105201-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -33.3 KB
Content
image-20231204105859-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -34.2 KB
Content
image-20231204110341-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -104.0 KB
Content
image-20231204110902-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -100.5 KB
Content
image-20231204111022-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -91.6 KB
Content
image-20231204111116-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -92.0 KB
Content
image-20231204111641-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -97.1 KB
Content
image-20231204111834-9.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -34.5 KB
Content
image-20231204112107-10.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -109.7 KB
Content
image-20231204113136-11.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -50.0 KB
Content
image-20231204113212-12.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -45.3 KB
Content
image-20231204113237-13.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Kilight
Size
... ... @@ -1,1 +1,0 @@
1 -93.5 KB
Content
image-20240117173123-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -120.8 KB
Content
image-20240117174452-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -132.1 KB
Content
image-20240117175009-3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -120.3 KB
Content
image-20240117175058-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -92.9 KB
Content
image-20240117175738-5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.ting
Size
... ... @@ -1,1 +1,0 @@
1 -56.8 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0