Skip to Content
Last modified by Mengting Qiu on 2025/07/03 18:49
From version 143.5
edited by Mengting Qiu
on 2025/07/03 18:27
Change comment: There is no comment for this version
To version 141.10
edited by Mengting Qiu
on 2025/06/16 10:14
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -982,7 +982,7 @@
982 982  
983 983  * Does your SIM card support NB-IoT network? If SIM card doesn't not specify support NB-IoT clearly, normally it doesn't support. You need to confirm with your operator.
984 984  * Do you configure the correct APN? [[Check here for APN settings>>http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H2.1GeneralConfiguretoattachnetwork]].
985 -* Do you lock the frequency band? This is the most case we see. [[Explain and Instruction>>||anchor="H1.ConfigureFrequencyBand"]].
985 +* Do you lock the frequency band? This is the most case we see. [[Explain and Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H2.2SpeedUpNetworkAttachtime]].
986 986  * Check if the device is attached to Carrier network but reject. (need to check with operator).
987 987  * Check if the antenna is connected firmly.
988 988  
... ... @@ -1013,14 +1013,12 @@
1013 1013  
1014 1014  === **MQTT Protocol:** ===
1015 1015  
1016 -==== **1. HEX-format** ====
1016 +Supports both **JSON-format** and **HEX-format** downlink commands (corresponding to AT commands).
1017 1017  
1018 -Supports **HEX-format** downlink commands (corresponding to AT commands).
1019 -
1020 1020  //Example~:// For the S31-CB's uplink interval modification (AT+TDC=900):
1021 1021  
1022 1022  * HEX format: (% style="color:blue" %)**01000384**(%%)  ~/~/ There are no Spaces. 0x0384(H)=900(D), that is, modify TDC to 900 seconds.
1023 -* JSON format: (% style="color:blue" %)**{AT+TDC=900}**(%%)**       **~/~/ The correct format is (% style="color:blue" %)**{AT Command}**(%%). No extra characters other than valid AT commands can be added within {}.
1021 +* JSON format: (% style="color:blue" %)**{AT+TDC=900}**(%%)**  **~/~/ The correct format is (% style="color:blue" %)**{AT Command}**(%%). No extra characters other than valid AT commands can be added within {}.
1024 1024  
1025 1025  (% style="color:red" %)**Note:**
1026 1026  
... ... @@ -1031,11 +1031,12 @@
1031 1031  (% style="color:red" %)**For example, the HEX-format downlink command corresponding to AT+TDC can only be used to configure TDC and cannot be used for queries. There is no HEX-format downlink command equivalent to AT+TDC=? , so querying TDC via downlink is not supported.**
1032 1032  
1033 1033  
1034 -==== **2. JSON-format ** ====
1035 1035  
1036 -**Template for Batch Configuration:**
1037 1037  
1038 -We can also use templates to configure multiple commands AT once. Users only need to modify the parameters of the required AT commands in the correct template for each device.
1034 +Json：
1035 +
1036 +The Json format in MQTT mode needs to be configured with all commands.
1037 +If you have configurations that need to be changed, please change them in the template below.
1039 1039  Template:
1040 1040  
1041 1041  {
... ... @@ -1061,18 +1061,16 @@
1061 1061  "AT+TEMPALARM3":"0"
1062 1062  }
1063 1063  
1064 -**Instructions for Using the Template:**
1063 +Hex：
1065 1065  
1066 -1. Modify the parameters for each AT command in the template as needed.
1067 -1. Send the entire template in one downlink command.
1065 +MQTT's hex format. Since many commands need to support strings, only a few commands are supported.
1068 1068  
1069 -(% style="color:red" %)**Note:**
1067 +The supported commands are consistent with LoRaWAN's hex commands.
1068 +Please refer to the following link to obtain the hex format:
1070 1070  
1071 -* The template may vary depending on the device model.
1072 -* **Currently, each specific template is being updated and tested**. If you need a template for your specific device, please contact **Dragino Technical Support** at [[support@dragino.com>>url:https://mailto:support@dragino.com/]] to request the latest downlink template.
1070 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
1073 1073  
1074 1074  
1075 -
1076 1076  == 7.4 What if the signal is good but the domain name resolution fails? ==
1077 1077  
1078 1078