Changes for page Firmware Upgrade Instruction -- ASR
Last modified by Mengting Qiu on 2024/07/01 09:19
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,5 +1,5 @@ 1 1 (% class="wikigeneratedid" %) 2 -**~ Table ofContents:**2 +**~ Contents:** 3 3 4 4 {{toc/}} 5 5 ... ... @@ -6,7 +6,6 @@ 6 6 7 7 = 1. Introduction = 8 8 9 - 10 10 This article shows the firmware upgrade method and troubleshooting for the below models Dragino sensors. 11 11 12 12 ... ... @@ -14,10 +14,8 @@ 14 14 15 15 == 2.1 LDS01/LWL01 == 16 16 17 - 18 18 [[Firmware Location>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]] 19 19 20 - 21 21 ((( 22 22 Pin Mapping: 23 23 ))) ... ... @@ -27,7 +27,7 @@ 27 27 LDS01/LWL01 Pin Mapping 28 28 29 29 30 - **DAP-Link Connection:**27 +DAP-Link Connection: 31 31 32 32 [[image:image-20220527083959-2.png]] 33 33 ... ... @@ -34,13 +34,10 @@ 34 34 Connect DAP-Link 35 35 36 36 37 - 38 38 == 2.2 LDS02/LWL02 == 39 39 40 - 41 41 [[Firmware Location(same as LDS01)>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]] 42 42 43 - 44 44 ((( 45 45 Pin Mapping: 46 46 ))) ... ... @@ -50,16 +50,13 @@ 50 50 LDS02/LDS02 v2.0 Pin Mapping 51 51 52 52 53 - 54 54 [[image:image-20220527084230-4.png]] 55 55 56 56 LDS02/LDS02 v2.2 Pin Mapping 57 57 58 58 59 - 60 60 == 2.3 LHT52 == 61 61 62 - 63 63 [[Firmware Location>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LHT52/firmware/]] 64 64 65 65 [[image:image-20220527084401-5.png]] ... ... @@ -67,12 +67,10 @@ 67 67 LHT52 Pin Mapping 68 68 69 69 70 - 71 71 = 3. How to Upgrade = 72 72 73 73 == 3.1 Use DAP-Link and Connect to the Device as above photos == 74 74 75 - 76 76 We need to connect VDD,GND,SWCLK,SWDIO to DAP-Link. 77 77 78 78 * Connection method: ... ... @@ -88,10 +88,8 @@ 88 88 [[image:image-20220527084505-6.png]] 89 89 90 90 91 - 92 92 == 3.2 Install PSoCProgrammer 3.27.1 == 93 93 94 - 95 95 ((( 96 96 Download Link: [[PSoCProgrammer3.27.1>>url:https://www.dragino.com/downloads/index.php?dir=tools/]] 97 97 ))) ... ... @@ -103,17 +103,13 @@ 103 103 [[image:image-20220527084537-7.png]] 104 104 105 105 106 - 107 107 == 3.3 Download Sensor Firmware == 108 108 109 - 110 110 Downlink sensor firmware to prepare the update 111 111 112 112 113 - 114 114 == 3.4 Upgrade Firmware == 115 115 116 - 117 117 Open PSOC Programmer, select the default configuration, no need to modify 118 118 119 119 [[image:image-20220527084612-8.png]] ... ... @@ -127,7 +127,6 @@ 127 127 [[image:image-20220527084739-10.png||height="453" width="1034"]] 128 128 129 129 130 - 131 131 ((( 132 132 Click the download icon, and the progress bar as shown in the figure below will appear. When PASS appears, it proves that the burning is successful. 133 133 ))) ... ... @@ -142,9 +142,8 @@ 142 142 ))) 143 143 144 144 ((( 145 - (% style="color:red" %)If you change different LoRa Frequency Bands/Region, you need using AT+FDR command to restore factory data after program success.127 +*If you change different LoRa Frequency Bands/Region, you need using AT+FDR command to restore factory data after program success. 146 146 147 - 148 148 149 149 ))) 150 150 ... ... @@ -152,6 +152,5 @@ 152 152 153 153 == 4.1 Unable to detect upgrade == 154 154 155 - 156 156 * Try to shot the bootloader pin to GND and reset the device. So the device will runs in bootloader mode. 157 157 * Or use AT+IREBOOT=7 to set the device to work in bootloader mode.