Changes for page Firmware Upgrade Instruction -- ASR
Last modified by Mengting Qiu on 2024/07/01 09:19
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,5 +1,5 @@ 1 1 (% class="wikigeneratedid" %) 2 -**~ Contents:** 2 +**~ Table of Contents:** 3 3 4 4 {{toc/}} 5 5 ... ... @@ -6,6 +6,7 @@ 6 6 7 7 = 1. Introduction = 8 8 9 + 9 9 This article shows the firmware upgrade method and troubleshooting for the below models Dragino sensors. 10 10 11 11 ... ... @@ -13,8 +13,10 @@ 13 13 14 14 == 2.1 LDS01/LWL01 == 15 15 17 + 16 16 [[Firmware Location>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]] 17 17 20 + 18 18 ((( 19 19 Pin Mapping: 20 20 ))) ... ... @@ -33,8 +33,10 @@ 33 33 34 34 == 2.2 LDS02/LWL02 == 35 35 39 + 36 36 [[Firmware Location(same as LDS01)>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]] 37 37 42 + 38 38 ((( 39 39 Pin Mapping: 40 40 ))) ... ... @@ -44,13 +44,16 @@ 44 44 LDS02/LDS02 v2.0 Pin Mapping 45 45 46 46 52 + 47 47 [[image:image-20220527084230-4.png]] 48 48 49 49 LDS02/LDS02 v2.2 Pin Mapping 50 50 51 51 58 + 52 52 == 2.3 LHT52 == 53 53 61 + 54 54 [[Firmware Location>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LHT52/firmware/]] 55 55 56 56 [[image:image-20220527084401-5.png]] ... ... @@ -62,6 +62,7 @@ 62 62 63 63 == 3.1 Use DAP-Link and Connect to the Device as above photos == 64 64 73 + 65 65 We need to connect VDD,GND,SWCLK,SWDIO to DAP-Link. 66 66 67 67 * Connection method: ... ... @@ -79,6 +79,7 @@ 79 79 80 80 == 3.2 Install PSoCProgrammer 3.27.1 == 81 81 91 + 82 82 ((( 83 83 Download Link: [[PSoCProgrammer3.27.1>>url:https://www.dragino.com/downloads/index.php?dir=tools/]] 84 84 ))) ... ... @@ -92,11 +92,13 @@ 92 92 93 93 == 3.3 Download Sensor Firmware == 94 94 105 + 95 95 Downlink sensor firmware to prepare the update 96 96 97 97 98 98 == 3.4 Upgrade Firmware == 99 99 111 + 100 100 Open PSOC Programmer, select the default configuration, no need to modify 101 101 102 102 [[image:image-20220527084612-8.png]] ... ... @@ -110,6 +110,7 @@ 110 110 [[image:image-20220527084739-10.png||height="453" width="1034"]] 111 111 112 112 125 + 113 113 ((( 114 114 Click the download icon, and the progress bar as shown in the figure below will appear. When PASS appears, it proves that the burning is successful. 115 115 ))) ... ... @@ -124,7 +124,7 @@ 124 124 ))) 125 125 126 126 ((( 127 - *If you change different LoRa Frequency Bands/Region, you need using AT+FDR command to restore factory data after program success.140 +(% style="color:red" %)If you change different LoRa Frequency Bands/Region, you need using AT+FDR command to restore factory data after program success. 128 128 129 129 130 130 ))) ... ... @@ -133,5 +133,6 @@ 133 133 134 134 == 4.1 Unable to detect upgrade == 135 135 149 + 136 136 * Try to shot the bootloader pin to GND and reset the device. So the device will runs in bootloader mode. 137 137 * Or use AT+IREBOOT=7 to set the device to work in bootloader mode.