Wiki source code of End Device Frequency Band

Version 11.1 by Xiaoling on 2022/05/30 10:40
Hide last authors
Xiaoling 3.1 1 (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %)
Xiaoling 3.12 2 **Contents：**
Xiaoling 1.1 3
Xiaoling 3.1 4 {{toc/}}
Xiaoling 1.1 5
Xiaoling 8.1 6
7
8
Xiaoling 3.1 9 = 1. Introduction =
Xiaoling 1.1 10
11 This page list the default frequency band for Dragino End Devices. The frequency bands are base on TTN Frequency Bands. User can modify upgrade firmware to support different frequency band or use AT Command to change the sub band in some frequency bands.
12
13 * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
14 * Frequency Bands vs Country List : Page 11 of [[LoRaWAN Regional Parameters RP2-1.0.3>>url:https://resources.lora-alliance.org/technical-specifications/rp2-1-0-3-lorawan-regional-parameters]]
15
Xiaoling 5.1 16
Xiaoling 3.1 17 = 2. OTAA Join Behaviour =
Xiaoling 1.1 18
19 For 005 LoRaWAN stack: to save battery, once boot, device will make first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again.
20
Xiaoling 3.6 21 (((
Xiaoling 1.1 22 For 005 LoRaWAN Stack:
Xiaoling 3.6 23 )))
Xiaoling 1.1 24
25 * EU868 OTAA Join DR select. SF7->SF8->SF9->SF10->SF11->SF12; Each 3 attempts and then loop
26 * US915 and AU915 OTAA Join procedure,. End node by default will use all 72 channels to join and it will be set to use the proper sub-band after Join success
27
Xiaoling 5.1 28
Xiaoling 3.1 29 = 3. Default Frequency Bands =
Xiaoling 1.1 30
31
Xiaoling 3.1 32 == 3.1 AS923 ==
Xiaoling 1.1 33
Xiaoling 3.1 34 === 3.1.1 Notice for AS923 Frequency Bands ===
Xiaoling 1.1 35
Xiaoling 3.6 36 (((
Xiaoling 1.1 37 Since [[RP002-1.0.1LoRaWAN Regional Parameters>>url:https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf]], AS923 include three different default settings for different countries: AS923-1, AS923-2 and AS923-3.
Xiaoling 3.6 38 )))
Xiaoling 1.1 39
Xiaoling 3.6 40 (((
Xiaoling 1.1 41 AS923-1 use the same default uplink frequency as previous AS923 firmware. AS923-2 and AS923-3 are new with different default uplink frequency. User need to know exactly the frequency bands from the LoRaWAN server and choose the right firmware version for the end node.
Xiaoling 3.6 42 )))
Xiaoling 1.1 43
44
Xiaoling 3.1 45 === 3.1.2 AS920-923 & AS923-925 : AS923-1 (AS923) ===
Xiaoling 1.1 46
47 * Default Uplink channel:
48 ** 923.2 - SF7BW125 to SF10BW125
49 ** 923.4 - SF7BW125 to SF10BW125
50
51 * Additional Uplink Channel: These channels are set during OTAA Join process from server. Below are the settings from TTN
52 * AS920~~AS923:
53 ** 922.2 - SF7BW125 to SF10BW125
54 ** 922.4 - SF7BW125 to SF10BW125
55 ** 922.6 - SF7BW125 to SF10BW125
56 ** 922.8 - SF7BW125 to SF10BW125
57 ** 923.0 - SF7BW125 to SF10BW125
58 ** 922.0 - SF7BW125 to SF10BW125
59
60 * AS923 ~~ AS925:
61 ** 923.6 - SF7BW125 to SF10BW125
62 ** 923.8 - SF7BW125 to SF10BW125
63 ** 924.0 - SF7BW125 to SF10BW125
64 ** 924.2 - SF7BW125 to SF10BW125
65 ** 924.4 - SF7BW125 to SF10BW125
66 ** 924.6 - SF7BW125 to SF10BW125
67
68 * Downlink:
69 ** Uplink channels 1-8 (RX1)
70 ** 923.2 - SF10BW125 (RX2)
71
Xiaoling 9.1 72
Xiaoling 11.1 73
Xiaoling 3.1 74 === 3.1.3 AS923-2 ===
Xiaoling 1.1 75
76 * Default Uplink channel:
77 ** 921.4 - SF7BW125 to SF10BW125
78 ** 921.6 - SF7BW125 to SF10BW125
79
80 * Additional Uplink Channels: These channels are set during OTAA Join process from server.
81
82 * Downlink:
83 ** Uplink channels 1-8 (RX1)
84 ** 921.4 - SF10BW125 (RX2)
85
Xiaoling 9.1 86
Xiaoling 11.1 87
Xiaoling 3.1 88 === 3.1.4 AS923-3 ===
Xiaoling 1.1 89
90 * Default Uplink channel:
91 ** 916.6 - SF7BW125 to SF10BW125
92 ** 916.8 - SF7BW125 to SF10BW125
93
94 * Additional Uplink Channels: These channels are set during OTAA Join process from server.
95
96 * Downlink:
97 ** Uplink channels 1-8 (RX1)
98 ** 916.6 - SF10BW125 (RX2)
99
Xiaoling 9.1 100
Xiaoling 11.1 101
Xiaoling 3.1 102 === 3.1.5 AS923-4 ===
Xiaoling 1.1 103
Edwin Chen 2.1 104 * Countries : Israel
Xiaoling 1.1 105 * Default Uplink channel:
106 ** 917.3 - SF7BW125 to SF10BW125
107 ** 917.5 - SF7BW125 to SF10BW125
108
109 * Additional Uplink Channels: These channels are set during OTAA Join process from server.
110 * Downlink:
111 ** Uplink channels 1-8 (RX1)
112 ** 917.3 - SF10BW125 (RX2)
113
Xiaoling 9.1 114
Xiaoling 11.1 115
Xiaoling 3.1 116 == 3.2 AU915-928(AU915) ==
Xiaoling 1.1 117
118 **Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]** , Default use CHE=2
119
120 * Uplink:
121 ** 916.8 - SF7BW125 to SF12BW125
122 ** 917.0 - SF7BW125 to SF12BW125
123 ** 917.2 - SF7BW125 to SF12BW125
124 ** 917.4 - SF7BW125 to SF12BW125
125 ** 917.6 - SF7BW125 to SF12BW125
126 ** 917.8 - SF7BW125 to SF12BW125
127 ** 918.0 - SF7BW125 to SF12BW125
128 ** 918.2 - SF7BW125 to SF12BW125
129
130 * Downlink:
131 ** 923.3 - SF7BW500 to SF12BW500
132 ** 923.9 - SF7BW500 to SF12BW500
133 ** 924.5 - SF7BW500 to SF12BW500
134 ** 925.1 - SF7BW500 to SF12BW500
135 ** 925.7 - SF7BW500 to SF12BW500
136 ** 926.3 - SF7BW500 to SF12BW500
137 ** 926.9 - SF7BW500 to SF12BW500
138 ** 927.5 - SF7BW500 to SF12BW500
139 ** 923.3 - SF12BW500(RX2 downlink only)
140
Xiaoling 3.8 141 (((
Xiaoling 1.1 142 There is a issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only works for the LoRaWAN server use sub-band2 , such as TTN. To solve this, user need to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvinient.
Xiaoling 3.8 143 )))
Xiaoling 1.1 144
Xiaoling 3.8 145
146 (((
Xiaoling 1.1 147 So since **Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]**, To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
Xiaoling 3.8 148 )))
Xiaoling 1.1 149
Xiaoling 3.8 150
151 (((
Xiaoling 1.1 152 After Join success, the end node will switch to the correct sub band by:
Xiaoling 3.8 153 )))
Xiaoling 1.1 154
Xiaoling 3.8 155 * (((
156 Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
157 )))
158 * (((
159 Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
Xiaoling 6.1 160
161
Xiaoling 3.8 162 )))
Xiaoling 1.1 163
Xiaoling 3.1 164 == 3.3 CN470-510 (CN470) ==
Xiaoling 1.1 165
166 Used in China, Default use CHE=1
167
168 * Uplink:
169 ** 486.3 - SF7BW125 to SF12BW125
170 ** 486.5 - SF7BW125 to SF12BW125
171 ** 486.7 - SF7BW125 to SF12BW125
172 ** 486.9 - SF7BW125 to SF12BW125
173 ** 487.1 - SF7BW125 to SF12BW125
174 ** 487.3 - SF7BW125 to SF12BW125
175 ** 487.5 - SF7BW125 to SF12BW125
176 ** 487.7 - SF7BW125 to SF12BW125
177
178 * Downlink:
179 ** 506.7 - SF7BW125 to SF12BW125
180 ** 506.9 - SF7BW125 to SF12BW125
181 ** 507.1 - SF7BW125 to SF12BW125
182 ** 507.3 - SF7BW125 to SF12BW125
183 ** 507.5 - SF7BW125 to SF12BW125
184 ** 507.7 - SF7BW125 to SF12BW125
185 ** 507.9 - SF7BW125 to SF12BW125
186 ** 508.1 - SF7BW125 to SF12BW125
187 ** 505.3 - SF12BW125 (RX2 downlink only)
188
Xiaoling 3.1 189 == 3.4 EU863-870 (EU868) ==
Xiaoling 1.1 190
191 * Uplink:
192 ** 868.1 - SF7BW125 to SF12BW125
193 ** 868.3 - SF7BW125 to SF12BW125 and SF7BW250
194 ** 868.5 - SF7BW125 to SF12BW125
195 ** 867.1 - SF7BW125 to SF12BW125
196 ** 867.3 - SF7BW125 to SF12BW125
197 ** 867.5 - SF7BW125 to SF12BW125
198 ** 867.7 - SF7BW125 to SF12BW125
199 ** 867.9 - SF7BW125 to SF12BW125
200 ** 868.8 - FSK
201
202 * Downlink:
203 ** Uplink channels 1-9 (RX1)
204 ** 869.525 - SF9BW125 (RX2 downlink only)
205
206 OTAA RX2DR is set to DR0, SF12BW125 since 2021,Mar for Dragino Devices.
207
208
Xiaoling 3.1 209 == 3.5 IN865-867 (IN865) ==
Xiaoling 1.1 210
211 * Uplink:
212 ** 865.0625 - SF7BW125 to SF12BW125
213 ** 865.4025 - SF7BW125 to SF12BW125
214 ** 865.9850 - SF7BW125 to SF12BW125
215
216 * Downlink:
217 ** Uplink channels 1-3 (RX1)
218 ** 866.550 - SF10BW125 (RX2)
219
Xiaoling 3.1 220 == 3.6 KZ865 ==
Xiaoling 1.1 221
222 * Uplink ~-~- 125Khz , DR0 - DR5
223 ** 865.1
224 ** 865.2
225 ** 865.5
226 ** 865.7
227 ** 865.9
228
229 * Downlink:
230 ** The RX1 receive window uses the same channel as the preceding uplink.
231 ** The RX2 receive window uses a fixed frequency and data rate. The default parameters are 866.7MHz / DR0 (SF12, 125 kHz)​
232
Xiaoling 3.1 233 == 3.7 KR920-923 (KR920) ==
Xiaoling 1.1 234
235 * Default channel:
236 ** 922.1 - SF7BW125 to SF12BW125
237 ** 922.3 - SF7BW125 to SF12BW125
238 ** 922.5 - SF7BW125 to SF12BW125
239
240 * Uplink: (OTAA mode, channel added by JoinAccept message)
241 ** 922.1 - SF7BW125 to SF12BW125
242 ** 922.3 - SF7BW125 to SF12BW125
243 ** 922.5 - SF7BW125 to SF12BW125
244 ** 922.7 - SF7BW125 to SF12BW125
245 ** 922.9 - SF7BW125 to SF12BW125
246 ** 923.1 - SF7BW125 to SF12BW125
247 ** 923.3 - SF7BW125 to SF12BW125
248
249 * Downlink:
250 ** Uplink channels 1-7(RX1)
251 ** 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
252
Xiaoling 3.1 253 == 3.8 MA869 ==
Xiaoling 1.1 254
Edwin Chen 4.1 255 Country: Morroco
256
Xiaoling 1.1 257 * Uplink:
258 ** 869.1 - SF7BW125 to SF12BW125
259 ** 869.3 - SF7BW125 to SF12BW125
260 ** 869.5 - SF7BW125 to SF12BW125
261 ** 869.7 - SF7BW125 to SF12BW125
262 ** 869.9 - SF7BW125 to SF12BW125
263 ** 870.0 - SF7BW125 to SF12BW125
264 ** 870.1 - SF7BW125 to SF12BW125
265 ** 870.3 - SF7BW125 to SF12BW125
266 ** 869.8 - FSK
267
268 * Downlink:
269 ** Uplink channels 1-9 (RX1)
270 ** 869.525 - SF12BW125 (RX2 downlink only)
271
Xiaoling 3.1 272 == 3.9 US902-928 (US915) ==
Xiaoling 1.1 273
274 Used in USA, Canada and South America.
275
Xiaoling 6.1 276
Xiaoling 3.1 277 === 3.9.1 Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]. ===
Xiaoling 1.1 278
279 Default use CHE=2, Subband 2
280
281 * Uplink:
282 ** 903.9 - SF7BW125 to SF10BW125
283 ** 904.1 - SF7BW125 to SF10BW125
284 ** 904.3 - SF7BW125 to SF10BW125
285 ** 904.5 - SF7BW125 to SF10BW125
286 ** 904.7 - SF7BW125 to SF10BW125
287 ** 904.9 - SF7BW125 to SF10BW125
288 ** 905.1 - SF7BW125 to SF10BW125
289 ** 905.3 - SF7BW125 to SF10BW125
290
291 * Downlink:
292 ** 923.3 - SF7BW500 to SF12BW500
293 ** 923.9 - SF7BW500 to SF12BW500
294 ** 924.5 - SF7BW500 to SF12BW500
295 ** 925.1 - SF7BW500 to SF12BW500
296 ** 925.7 - SF7BW500 to SF12BW500
297 ** 926.3 - SF7BW500 to SF12BW500
298 ** 926.9 - SF7BW500 to SF12BW500
299 ** 927.5 - SF7BW500 to SF12BW500
300 ** 923.3 - SF12BW500(RX2 downlink only)
301
Xiaoling 3.1 302 === 3.9.2 Latest firmware, Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]] ===
Xiaoling 1.1 303
Xiaoling 3.7 304 (((
Xiaoling 1.1 305 There is an issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only work for the LoRaWAN server use sub-band2 , such as TTN. To solve this, the user needs to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvenient.
Xiaoling 3.7 306 )))
Xiaoling 1.1 307
Xiaoling 3.7 308 (((
309
310 )))
311
312 (((
Xiaoling 1.1 313 So since **Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]**, we have improved this, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join, In this case, In this case, the end node can support LoRaWAN servers with different subbands. To make sure the end node will only transmit the proper sub-band after OTAA Joined successfully, the end node will:
Xiaoling 3.7 314 )))
Xiaoling 1.1 315
Xiaoling 3.7 316 * (((
317 Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that subband
318 )))
319 * (((
320 Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include)
Xiaoling 6.1 321
322
Xiaoling 3.7 323 )))
Xiaoling 1.1 324
Xiaoling 3.1 325 = 4. Frequency Bands for different server =
Xiaoling 1.1 326
327 * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
328 * Loriot [[https:~~/~~/docs.loriot.io/display/LNS/Regional+Frequency+Plans>>url:https://docs.loriot.io/display/LNS/Regional+Frequency+Plans]]

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0