Changes for page End Device Frequency Band
Last modified by Edwin Chen on 2024/10/21 20:35
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,5 +1,5 @@ 1 1 (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %) 2 - **Contents：** 2 + **Table of** **Contents：** 3 3 4 4 {{toc/}} 5 5 ... ... @@ -8,6 +8,7 @@ 8 8 9 9 = 1. Introduction = 10 10 11 + 11 11 This page list the default frequency band for Dragino End Devices. The frequency bands are base on TTN Frequency Bands. User can modify upgrade firmware to support different frequency band or use AT Command to change the sub band in some frequency bands. 12 12 13 13 * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]] ... ... @@ -16,6 +16,7 @@ 16 16 17 17 = 2. OTAA Join Behaviour = 18 18 20 + 19 19 For 005 LoRaWAN stack: to save battery, once boot, device will make first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again. 20 20 21 21 ((( ... ... @@ -28,11 +28,11 @@ 28 28 29 29 = 3. Default Frequency Bands = 30 30 31 - 32 32 == 3.1 AS923 == 33 33 34 34 === 3.1.1 Notice for AS923 Frequency Bands === 35 35 37 + 36 36 ((( 37 37 Since [[RP002-1.0.1LoRaWAN Regional Parameters>>url:https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf]], AS923 include three different default settings for different countries: AS923-1, AS923-2 and AS923-3. 38 38 ))) ... ... @@ -44,6 +44,8 @@ 44 44 45 45 === 3.1.2 AS920-923 & AS923-925 : AS923-1 (AS923) === 46 46 49 + 50 +* **Countries**: Malaysia, 47 47 * Default Uplink channel: 48 48 ** 923.2 - SF7BW125 to SF10BW125 49 49 ** 923.4 - SF7BW125 to SF10BW125 ... ... @@ -70,9 +70,9 @@ 70 70 ** 923.2 - SF10BW125 (RX2) 71 71 72 72 73 - 74 74 === 3.1.3 AS923-2 === 75 75 79 + 76 76 * Default Uplink channel: 77 77 ** 921.4 - SF7BW125 to SF10BW125 78 78 ** 921.6 - SF7BW125 to SF10BW125 ... ... @@ -84,9 +84,9 @@ 84 84 ** 921.4 - SF10BW125 (RX2) 85 85 86 86 87 - 88 88 === 3.1.4 AS923-3 === 89 89 93 + 90 90 * Default Uplink channel: 91 91 ** 916.6 - SF7BW125 to SF10BW125 92 92 ** 916.8 - SF7BW125 to SF10BW125 ... ... @@ -98,9 +98,9 @@ 98 98 ** 916.6 - SF10BW125 (RX2) 99 99 100 100 101 - 102 102 === 3.1.5 AS923-4 === 103 103 107 + 104 104 * Countries : Israel 105 105 * Default Uplink channel: 106 106 ** 917.3 - SF7BW125 to SF10BW125 ... ... @@ -112,9 +112,9 @@ 112 112 ** 917.3 - SF10BW125 (RX2) 113 113 114 114 115 - 116 116 == 3.2 AU915-928(AU915) == 117 117 121 + 118 118 **Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]** , Default use CHE=2 119 119 120 120 * Uplink: ... ... @@ -156,13 +156,15 @@ 156 156 Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band 157 157 ))) 158 158 * ((( 159 -Use the Join successful sub-band if the server doesn ’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)163 +Use the Join successful sub-band if the server doesn't include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include) 160 160 165 + 161 161 162 162 ))) 163 163 164 164 == 3.3 CN470-510 (CN470) == 165 165 171 + 166 166 Used in China, Default use CHE=1 167 167 168 168 * Uplink: ... ... @@ -187,9 +187,9 @@ 187 187 ** 505.3 - SF12BW125 (RX2 downlink only) 188 188 189 189 190 - 191 191 == 3.4 EU863-870 (EU868) == 192 192 198 + 193 193 * Uplink: 194 194 ** 868.1 - SF7BW125 to SF12BW125 195 195 ** 868.3 - SF7BW125 to SF12BW125 and SF7BW250 ... ... @@ -210,6 +210,7 @@ 210 210 211 211 == 3.5 IN865-867 (IN865) == 212 212 219 + 213 213 * Uplink: 214 214 ** 865.0625 - SF7BW125 to SF12BW125 215 215 ** 865.4025 - SF7BW125 to SF12BW125 ... ... @@ -219,10 +219,21 @@ 219 219 ** Uplink channels 1-3 (RX1) 220 220 ** 866.550 - SF10BW125 (RX2) 221 221 229 +Gateway has below eight channels in IN865 bands. 222 222 231 +* 865.0625 - SF7BW125 to SF12BW125 232 +* 865.4025 - SF7BW125 to SF12BW125 233 +* 865.6025 - SF7BW125 to SF12BW125 234 +* 865.9850 - SF7BW125 to SF12BW125 235 +* 866.1850 - SF7BW125 to SF12BW125 236 +* 866.3850 - SF7BW125 to SF12BW125 237 +* 866.5850 - SF7BW125 to SF12BW125 238 +* 866.7850 - SF7BW125 to SF12BW125 223 223 240 + 224 224 == 3.6 KZ865 == 225 225 243 + 226 226 * Uplink ~-~- 125Khz , DR0 - DR5 227 227 ** 865.1 228 228 ** 865.2 ... ... @@ -235,9 +235,9 @@ 235 235 ** The RX2 receive window uses a fixed frequency and data rate. The default parameters are 866.7MHz / DR0 (SF12, 125 kHz) 236 236 237 237 238 - 239 239 == 3.7 KR920-923 (KR920) == 240 240 258 + 241 241 * Default channel: 242 242 ** 922.1 - SF7BW125 to SF12BW125 243 243 ** 922.3 - SF7BW125 to SF12BW125 ... ... @@ -257,9 +257,9 @@ 257 257 ** 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125) 258 258 259 259 260 - 261 261 == 3.8 MA869 == 262 262 280 + 263 263 Country: Morroco 264 264 265 265 * Uplink: ... ... @@ -278,14 +278,15 @@ 278 278 ** 869.525 - SF12BW125 (RX2 downlink only) 279 279 280 280 281 - 282 282 == 3.9 US902-928 (US915) == 283 283 301 + 284 284 Used in USA, Canada and South America. 285 285 286 286 287 287 === 3.9.1 Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]. === 288 288 307 + 289 289 Default use CHE=2, Subband 2 290 290 291 291 * Uplink: ... ... @@ -309,8 +309,10 @@ 309 309 ** 927.5 - SF7BW500 to SF12BW500 310 310 ** 923.3 - SF12BW500(RX2 downlink only) 311 311 331 + 312 312 === 3.9.2 Latest firmware, Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]] === 313 313 334 + 314 314 ((( 315 315 There is an issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only work for the LoRaWAN server use sub-band2 , such as TTN. To solve this, the user needs to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvenient. 316 316 ))) ... ... @@ -329,10 +329,12 @@ 329 329 * ((( 330 330 Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include) 331 331 353 + 332 332 333 333 ))) 334 334 335 335 = 4. Frequency Bands for different server = 336 336 359 + 337 337 * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]] 338 338 * Loriot [[https:~~/~~/docs.loriot.io/display/LNS/Regional+Frequency+Plans>>url:https://docs.loriot.io/display/LNS/Regional+Frequency+Plans]]