Changes for page End Device Frequency Band

Last modified by Edwin Chen on 2024/10/21 20:35
<
From version < 4.1 >
edited by Edwin Chen
on 2022/05/19 06:54
To version < 14.1 >
edited by Edwin Chen
on 2023/02/02 14:22
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,17 +1,23 @@
1 1  (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %)
2 - **Contents：**
2 + **Table of** **Contents：**
3 3  
4 4  {{toc/}}
5 5  
6 +
7 +
8 +
6 6  = 1. Introduction =
7 7  
11 +
8 8  This page list the default frequency band for Dragino End Devices. The frequency bands are base on TTN Frequency Bands. User can modify upgrade firmware to support different frequency band or use AT Command to change the sub band in some frequency bands.
9 9  
10 10  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
11 11  * Frequency Bands vs Country List : Page 11 of [[LoRaWAN Regional Parameters RP2-1.0.3>>url:https://resources.lora-alliance.org/technical-specifications/rp2-1-0-3-lorawan-regional-parameters]]
12 12  
17 +
13 13  = 2. OTAA Join Behaviour =
14 14  
20 +
15 15  For 005 LoRaWAN stack: to save battery, once boot, device will make first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again.
16 16  
17 17  (((
... ... @@ -21,13 +21,14 @@
21 21  * EU868 OTAA Join DR select. SF7->SF8->SF9->SF10->SF11->SF12; Each 3 attempts and then loop
22 22  * US915 and AU915 OTAA Join procedure,. End node by default will use all 72 channels to join and it will be set to use the proper sub-band after Join success
23 23  
30 +
24 24  = 3. Default Frequency Bands =
25 25  
26 -
27 27  == 3.1 AS923 ==
28 28  
29 29  === 3.1.1 Notice for AS923 Frequency Bands ===
30 30  
37 +
31 31  (((
32 32  Since [[RP002-1.0.1LoRaWAN Regional Parameters>>url:https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf]], AS923 include three different default settings for different countries: AS923-1, AS923-2 and AS923-3.
33 33  )))
... ... @@ -37,9 +37,10 @@
37 37  )))
38 38  
39 39  
40 -
41 41  === 3.1.2 AS920-923 & AS923-925 : AS923-1 (AS923) ===
42 42  
49 +
50 +* **Countries**: Malaysia,
43 43  * Default Uplink channel:
44 44  ** 923.2 - SF7BW125 to SF10BW125
45 45  ** 923.4 - SF7BW125 to SF10BW125
... ... @@ -65,8 +65,10 @@
65 65  ** Uplink channels 1-8 (RX1)
66 66  ** 923.2 - SF10BW125 (RX2)
67 67  
76 +
68 68  === 3.1.3 AS923-2 ===
69 69  
79 +
70 70  * Default Uplink channel:
71 71  ** 921.4 - SF7BW125 to SF10BW125
72 72  ** 921.6 - SF7BW125 to SF10BW125
... ... @@ -77,8 +77,10 @@
77 77  ** Uplink channels 1-8 (RX1)
78 78  ** 921.4 - SF10BW125 (RX2)
79 79  
90 +
80 80  === 3.1.4 AS923-3 ===
81 81  
93 +
82 82  * Default Uplink channel:
83 83  ** 916.6 - SF7BW125 to SF10BW125
84 84  ** 916.8 - SF7BW125 to SF10BW125
... ... @@ -89,8 +89,10 @@
89 89  ** Uplink channels 1-8 (RX1)
90 90  ** 916.6 - SF10BW125 (RX2)
91 91  
104 +
92 92  === 3.1.5 AS923-4 ===
93 93  
107 +
94 94  * Countries : Israel
95 95  * Default Uplink channel:
96 96  ** 917.3 - SF7BW125 to SF10BW125
... ... @@ -101,8 +101,10 @@
101 101  ** Uplink channels 1-8 (RX1)
102 102  ** 917.3 - SF10BW125 (RX2)
103 103  
118 +
104 104  == 3.2 AU915-928(AU915) ==
105 105  
121 +
106 106  **Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]** , Default use CHE=2
107 107  
108 108  * Uplink:
... ... @@ -144,11 +144,15 @@
144 144  Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
145 145  )))
146 146  * (((
147 -Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
163 +Use the Join successful sub-band if the server doesn't include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
164 +
165 +
166 +
148 148  )))
149 149  
150 150  == 3.3 CN470-510 (CN470) ==
151 151  
171 +
152 152  Used in China, Default use CHE=1
153 153  
154 154  * Uplink:
... ... @@ -172,8 +172,10 @@
172 172  ** 508.1 - SF7BW125 to SF12BW125
173 173  ** 505.3 - SF12BW125 (RX2 downlink only)
174 174  
195 +
175 175  == 3.4 EU863-870 (EU868) ==
176 176  
198 +
177 177  * Uplink:
178 178  ** 868.1 - SF7BW125 to SF12BW125
179 179  ** 868.3 - SF7BW125 to SF12BW125 and SF7BW250
... ... @@ -194,6 +194,7 @@
194 194  
195 195  == 3.5 IN865-867 (IN865) ==
196 196  
219 +
197 197  * Uplink:
198 198  ** 865.0625 - SF7BW125 to SF12BW125
199 199  ** 865.4025 - SF7BW125 to SF12BW125
... ... @@ -203,8 +203,21 @@
203 203  ** Uplink channels 1-3 (RX1)
204 204  ** 866.550 - SF10BW125 (RX2)
205 205  
229 +Gateway has below eight channels in IN865 bands.
230 +
231 +* 865.0625 - SF7BW125 to SF12BW125
232 +* 865.4025 - SF7BW125 to SF12BW125
233 +* 865.6025 - SF7BW125 to SF12BW125
234 +* 865.9850 - SF7BW125 to SF12BW125
235 +* 866.1850 - SF7BW125 to SF12BW125
236 +* 866.3850 - SF7BW125 to SF12BW125
237 +* 866.5850 - SF7BW125 to SF12BW125
238 +* 866.7850 - SF7BW125 to SF12BW125
239 +
240 +
206 206  == 3.6 KZ865 ==
207 207  
243 +
208 208  * Uplink ~-~- 125Khz , DR0 - DR5
209 209  ** 865.1
210 210  ** 865.2
... ... @@ -216,8 +216,10 @@
216 216  ** The RX1 receive window uses the same channel as the preceding uplink.
217 217  ** The RX2 receive window uses a fixed frequency and data rate. The default parameters are 866.7MHz / DR0 (SF12, 125 kHz)​
218 218  
255 +
219 219  == 3.7 KR920-923 (KR920) ==
220 220  
258 +
221 221  * Default channel:
222 222  ** 922.1 - SF7BW125 to SF12BW125
223 223  ** 922.3 - SF7BW125 to SF12BW125
... ... @@ -236,8 +236,10 @@
236 236  ** Uplink channels 1-7(RX1)
237 237  ** 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
238 238  
277 +
239 239  == 3.8 MA869 ==
240 240  
280 +
241 241   Country: Morroco
242 242  
243 243  * Uplink:
... ... @@ -255,12 +255,16 @@
255 255  ** Uplink channels 1-9 (RX1)
256 256  ** 869.525 - SF12BW125 (RX2 downlink only)
257 257  
298 +
258 258  == 3.9 US902-928 (US915) ==
259 259  
301 +
260 260  Used in USA, Canada and South America.
261 261  
304 +
262 262  === 3.9.1 Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]. ===
263 263  
307 +
264 264  Default use CHE=2, Subband 2
265 265  
266 266  * Uplink:
... ... @@ -284,8 +284,10 @@
284 284  ** 927.5 - SF7BW500 to SF12BW500
285 285  ** 923.3 - SF12BW500(RX2 downlink only)
286 286  
331 +
287 287  === 3.9.2 Latest firmware, Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]] ===
288 288  
334 +
289 289  (((
290 290  There is an issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only work for the LoRaWAN server use sub-band2 , such as TTN. To solve this, the user needs to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvenient.
291 291  )))
... ... @@ -303,9 +303,36 @@
303 303  )))
304 304  * (((
305 305  Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include)
352 +
353 +
354 +
306 306  )))
307 307  
308 308  = 4. Frequency Bands for different server =
309 309  
359 +
310 310  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
311 311  * Loriot [[https:~~/~~/docs.loriot.io/display/LNS/Regional+Frequency+Plans>>url:https://docs.loriot.io/display/LNS/Regional+Frequency+Plans]]
362 +
363 +
364 += 5. Subband Related questiones in US915, AU915, CN470 bands. =
365 +
366 +Frequency band US915, AU915 and CN470 supports totally 72 frequency in 8 sub-bands, Normally Gateway only support 8 channels ( one subband). So how does the gateway and end nodes work in such frequency?
367 +
368 +== 5.1 Set Subband in Gateway. ==
369 +
370 +* If Gateway choose **Semtech UDP packet** forwarder to Connect to LoRaWAN server. User need to manually set the match Subband in the gateway web UI.
371 +* If Gateway choose **Basic Station Mode** to connect to the LoRaWAN server. User can set the subband in the Server side and gateway will the correct subband from server. no need to set this in gateway. AWS-IoT, TTN, ChirpStack all supports Basic Station Connection.
372 +
373 +== 5.2 Set Subband in End Node ==
374 +
375 +* In early End Node firmware, it is pre-set to subband 2 , user need to manually set to proper subband if they don;t use subband 2.
376 +* In new end node firmware , it supports all sub-bands, and will swtich to the proper subband after OTAA join. So user can use the end node with all sub-band.
377 +
378 +Reference: [[How it affects the OTAA Join when end node is set to support all subbands>>http://wiki.dragino.com/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/#H13.WhyittakeslongertimeforOTAAjoinedinUS9152FCN4702FAU915band3F]]?
379 +
380 +
381 +
382 +
383 +
384 +

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0